The 164 registers of USBHS (USB High Speed), from 0x46000000, with their reset value and every field. The PIC32CK1025GC01144 has 5730 registers in 69 peripherals, one page each.
USBHS USB High Speed
CTRLAUSBHS Control Register A. (All bits except ENABLE and SWRST are Enable protected)
Address
0x46000000
Reset
0x00000000
Access
read/write
Size
32-bit
5 fields
Field
Bits
What it does
REFCLKSEL
10
Select USB PLL Reference Clock Speed
IDOVEN
9
ID Source Select
IDVAL
8
Override Valud of ID
ENABLE
1
USBHS Enable
SWRST
0
USBHS Software Reset
CTRLBUSBHS Control Register B
Address
0x46000004
Reset
0x00000000
Access
read/write
Size
32-bit
1 field
Field
Bits
What it does
BLANK
19:0
Blank the wakeup monitoring for a specific real time
0 No blank delay
1048575 Maximum blank delay
CTRLCUSBHS Control Register C
Address
0x46000008
Reset
0x00000000
Access
read/write
Size
32-bit
1 field
Field
Bits
What it does
T1MSEN
4
REFCLK and SUSPENDM override
INTENCLRUSBHS Interrupt Enable Clear Register
Address
0x4600000C
Reset
0x00000000
Access
read/write
Size
32-bit
6 fields
Field
Bits
What it does
PHYRDY
5
Clear PHYRDY Interrupt Enable
T1MS
4
Clear T1MS Interrupt Enable
DMA
3
Clear DMA Interrupt Enable
USB
2
Clear USBCORE General Interrupt Enable
RESUME
1
Clear Resume Interrupt Enable
WAKEUP
0
Clear USCORE Detaction Interrupt Enable
INTENSETUSBHS Interrupt Enable Clear Register
Address
0x46000010
Reset
0x00000000
Access
read/write
Size
32-bit
6 fields
Field
Bits
What it does
PHYRDY
5
PHYRDY Interrupt Enable
T1MS
4
T1MS Interrupt Enable
DMA
3
DMA Interrupt Enable
USB
2
USBCORE General Interrupt Enable
RESUME
1
Resume Interrupt Enable
WAKEUP
0
USCORE Detaction Interrupt Enable
INTFLAGUSBHS Interrupt Flag Register
Address
0x46000014
Reset
0x00000000
Access
read/write
Size
32-bit
6 fields
Field
Bits
What it does
PHYRDY
5
PHY Ready Interrupt
T1MS
4
Timer 1ms Tick Interrupt
DMA
3
DMA Interrupt
USB
2
USBCORE General Interrupt
RESUME
1
Resume Interrupt
WAKEUP
0
USB Activity Detection Interrupt
STATUSUSBHS Status Register
Address
0x46000018
Reset
0x00000000
Access
read only
Size
32-bit
3 fields
Field
Bits
What it does
VREGRDY
2
USB Voltage Regulator Status
PHYON
1
Power On of PHY Complete
PHYRDY
0
PHY Is Ready for USBCORE Activity
SYNCBUSYUSBHS Syncbusy Register
Address
0x4600001C
Reset
0x00000000
Access
read only
Size
32-bit
3 fields
Field
Bits
What it does
T1MSEN
2
T1MS enable busy bit
ENABLE
1
Enable busy bit
SWRST
0
Software reset busy bit
FADDRFunction Address Register
Address
0x46001000
Reset
0x00
Access
read/write
7–
6FUNCADDR6
5FUNCADDR5
4FUNCADDR4
3FUNCADDR3
2FUNCADDR2
1FUNCADDR1
0FUNCADDR0
1 field
Field
Bits
What it does
FUNCADDR
6:0
Function address
POWRUsed For Controlling Suspend And Resume Signaling And Some Basic Operation Of USBCORE
Address
0x46001001
Reset
0x20
Access
read/write
7ISOUPD
6SOFTCONN
5HSEN
4HSMODE
3RESET
2RESUME
1SUSPMODE
0SUSPEN
8 fields
Field
Bits
What it does
ISOUPD
7
when set by cpu the usbcore will wait for an sof token
SOFTCONN
6
if enabled the D+ D- lines are enabled when this bit is set by the cpu
HSEN
5
when set by cpu the usbcore will negotiate the high speed mode
HSMODE
4
when set this read only bit indicates high speed mode successfully negotiated during usb reset
RESET
3
this bit is set when reset signaling is present on the bus
RESUME
2
set by cpu to generate resume signaling when te device is in suspend
SUSPMODE
1
set by cpu to enter suspend mode
SUSPEN
0
set by the cpu to enable suspendm output
INTRTXRead Only Register Which Indicates Which Interrupts Are Currently Active For EP0 And TX EP1-15
Address
0x46001002
Reset
0x0000
Access
read only
Size
16-bit
8 fields
Field
Bits
What it does
EP7TX
7
Interrupts Active For TX7 Endpoint
EP6TX
6
Interrupts Active For TX6 Endpoint
EP5TX
5
Interrupts Active For TX5 Endpoint
EP4TX
4
Interrupts Active For TX4 Endpoint
EP3TX
3
Interrupts Active For TX3 Endpoint
EP2TX
2
Interrupts Active For TX2 Endpoint
EP1TX
1
Interrupts Active For TX1 Endpoint
EP0TX
0
Interrupts Active For TX0 Endpoint
INTRRXRead Only Register Which Indicates Which Interrupts Are Currently Active For RX EP1-15
Address
0x46001004
Reset
0x0000
Access
read only
Size
16-bit
7 fields
Field
Bits
What it does
EP7RX
7
Interrupts Active For Which RX7 Endpoint
EP6RX
6
Interrupts Active For Which RX6 Endpoint
EP5RX
5
Interrupts Active For Which RX5 Endpoint
EP4RX
4
Interrupts Active For Which RX4 Endpoint
EP3RX
3
Interrupts Active For Which RX3 Endpoint
EP2RX
2
Interrupts Active For Which RX2 Endpoint
EP1RX
1
Interrupts Active For Which RX1 Endpoint
INTRTXEInterrupt Enable Bits for INTRTX
Address
0x46001006
Reset
0xFFFF
Access
read/write
Size
16-bit
8 fields
Field
Bits
What it does
EP7TXEN
7
Interrupt Enabled for TX EP7
EP6TXEN
6
Interrupt Enabled for TX EP6
EP5TXEN
5
Interrupt Enabled for TX EP5
EP4TXEN
4
Interrupt Enabled for TX EP4
EP3TXEN
3
Interrupt Enabled for TX EP3
EP2TXEN
2
Interrupt Enabled for TX EP2
EP1TXEN
1
Interrupt Enabled for TX EP1
EP0TXEN
0
Interrupt Enabled for TX EP0
INTRRXEInterrupt Enable Bits for INTRRX
Address
0x46001008
Reset
0xFFFE
Access
read/write
Size
16-bit
7 fields
Field
Bits
What it does
EP7RXE
7
Interrupt Enabled for RX EP7
EP6RXE
6
Interrupt Enabled for RX EP6
EP5RXE
5
Interrupt Enabled for RX EP5
EP4RXE
4
Interrupt Enabled for RX EP4
EP3RXE
3
Interrupt Enabled for RX EP3
EP2RXE
2
Interrupt Enabled for RX EP2
EP1RXE
1
Interrupt Enabled for RX EP1
INTRUSBRead Only Register Which Indicates Which USB Interrupts Are Currently Active.
Address
0x4600100A
Reset
0x00
Access
read only
7VBUSERR
6SESSREQ
5DISCON
4CONN
3SOF
2RESET
1RESUME
0SUSPEND
8 fields
Field
Bits
What it does
VBUSERR
7
Set When VBus Drops Below The VBus Valid Threshold During A Session.
SESSREQ
6
Set When Session Request Signaling Has Been Detected.
DISCON
5
Set In Host Mode When A Device Disconnect Is Detected.Set In Peripheral Mode When A Session Ends
CONN
4
Set When A Device Connection Is Detected
SOF
3
Set When A New Frame Starts
RESET
2
Set In Peripheral Mode when Reset Is Detected On The Bus. In HostMode When Babble Is Detected
RESUME
1
Set When Resume Signal Is Detected On The Bus
SUSPEND
0
Set When Suspend Signal Is Detected On The Bus
INTRUSBEInterrupt Enable Bits for USB Interrupts
Address
0x4600100B
Reset
0x06
Access
read/write
7VBUSERREN
6SESSREQEN
5DISCONEN
4CONNEN
3SOFEN
2RESETEN
1RESUMEEN
0SUSPENDEN
8 fields
Field
Bits
What it does
VBUSERREN
7
VBus Error Interrupt Enable
SESSREQEN
6
SESSREQ Interrupt Enable
DISCONEN
5
DISCONN Interrupt Enable
CONNEN
4
CONN Interrupt Enable
SOFEN
3
SOF Interrupt Enable
RESETEN
2
RESET/BABBLE Interrupt Enable
RESUMEEN
1
RESUME Interrupt Enable
SUSPENDEN
0
SUSEPND Interrupt Enable
FRAMEHolds The Last Received Frame Number
Address
0x4600100C
Reset
0x0000
Access
read only
Size
16-bit
1 field
Field
Bits
What it does
FRMNUM
10:0
Frame Number
INDEXIndex Is A 4-Bit Register That Determines Which Endpoint Control/Status Registers Are Accessed
Address
0x4600100E
Reset
0x00
Access
read/write
7–
6–
5–
4–
3SELEP3
2SELEP2
1SELEP1
0SELEP0
1 field
Field
Bits
What it does
SELEP
3:0
The Selected Endpoint
0 Endpoint 0 Select
1 Endpoint 1 Select
2 Endpoint 2 Select
3 Endpoint 3 Select
4 Endpoint 4 Select
5 Endpoint 5 Select
6 Endpoint 6 Select
7 Endpoint 7 Select
8 Endpoint 8 Select
TESTMODENot Used In Normal Operation. Configuration To Put the USBCORE Into One Of The Four Test Modes For HighSpeed Operation
Address
0x4600100F
Reset
0x00
Access
read/write
7FORCEHOST
6FIFOACCESS
5FORCEFS
4FORCEHS
3TESTPACKET
2TESTK
1TESTJ
0TESTSE0NAK
8 fields
Field
Bits
What it does
FORCEHOST
7
The CPU Sets This Bit To Instruct The Core To Enter Host Mode When The Session Bit Is Set
FIFOACCESS
6
The CPU Sets This Bit To Transfer The Packet In The Endpoint 0 TX FIFO To The Endpoint 0 Rx FIFO. It Is Cleared Automatically.
FORCEFS
5
Depending On Bit 7 Force Controller Into FS Speed Mode
FORCEHS
4
Depending On Bit 7 Force Controller Into High Speed Mode
TESTPACKET
3
Set To Enter The Test_Packet mode
TESTK
2
Set To Enter The Test_K mode
TESTJ
1
Set To Enter The Test_J mode
TESTSE0NAK
0
Set To Enter The Test_SE0_NAK mode
ENDPOINTX.TXMAXPENDPOINTX Maximum Amount Of Data That Can Be Transferred Through The Selected TX Endpoint In A Single Operation
Address
0x46001010
Reset
0x0000
Access
read/write
Size
16-bit
2 fields
Field
Bits
What it does
MULTIPLIER
15:11
Multiplier Value (m-1)
MAXPAYLOAD
10:0
Maximum Payload/Transactions
ENDPOINT0.CSR0LENDPOINT0 Control And Status Bits for TX Endpoint 0
Address
0x46001012
Reset
0x00
Access
read/write
7NAKTIMEOUT
6SERVICEDRXPKTRDY
5REQPKT
4ERROR
3DATAEND
2RXSTALL
1TXPKTRDY
0RXPKTRDY
14 fields
Field
Bits
What it does
NAKTIMEOUT
7
This Bit Will Be Set When Endpoint 0 Is Halted Following The Receipt Of NAK Responses For Longer Than The Time Set By The NAKLimit0 register.
SERVICEDSETUPEND
7
The CPU Writes A 1 To This Bit To Clear The SetupEnd Bit. It Is Cleared Automatically.
SERVICEDRXPKTRDY
6
The CPU Writes A 1 To This Bit To Clear The RxPktRdy Bit. It Is Cleared Automatically
STATUSPKT
6
The CPU Sets This Bit At The Same Time As The TxPktRdy Or ReqPkt Bit Is Set, To Perform A Status Stage Transaction
REQPKT
5
The CPU Sets This Bit To Request An IN Transaction
SENDSTALL
5
The CPU Writes A 1 To This Bit To Terminate The Current Transaction
ERROR
4
This Bit Will Be Set When Three Attempts Have Been Made To Perform A Transaction With No Response From The Peripheral
SETUPEND
4
This Bit Will Be Set When A Control Transaction Ends Before The DataEnd Bit Has Been Set
DATAEND
3
The CPU Sets This Bit 1. When Setting TxPktRdy For The Last Data Packet 2. When Clearing RxPktRdy After Unloading The Last Data Packet.3. When Setting TxPktRdy For A Zero Length Data Packet.
SETUPPKT
3
The CPU Sets This Bit, At The Same Time As The TxPktRdy Bit Is Set, To Send A SETUP Token Instead Of An OUT Token For The Transaction
RXSTALL
2
This Bit Is Set When A Stall Handshake Is Received.
SENTSTALL
2
This Bit Is Set When A Stall Handshake Is Transmitted.
TXPKTRDY
1
The CPU Sets This Bit After Loading A Data Packet Into The FIFO.
RXPKTRDY
0
This Bit Is Set When A Data Packet Has Been Received
ENDPOINTX.TXCSRLENDPOINTX Control And Status Bits for TX Endpoints 1-15
Address
0x46001012
Reset
0x00
Access
read/write
7INCOMPTX
6CLRDATATOG
5RXSTALL
4SENDSTALL
3FLUSHFIFO
2ERROR
1FIFONOTEMPTY
0TXPKTRDY
12 fields
Field
Bits
What it does
INCOMPTX
7
When The Endpoint Is Being Used For High-Bandwidth Isochronous, This Bit Is Set To Indicate Where A Large Packet Has Been Split Into 2 Or 3 Packets For Transmission But Insufficient IN Tokens Have Been Received To Send All The Parts.
NAKTIMEOUT
7
This Bit Will Be Set When Endpoint 0 Is Halted Following The Receipt Of NAK Responses For Longer Than The Time Set By The NAKLimit0 register.
CLRDATATOG
6
The CPU Writes A 1 To This Bit To Reset The Endpoint Data Toggle To 0.
RXSTALL
5
This Bit Is Set When A Stall Handshake Is Received.
SENTSTALL
5
This Bit Is Set When A Stall Handshake Is Transmitted.
SENDSTALL
4
The CPU Writes A 1 To This Bit To Issue A Stall Handshake To An In Token
SETUPPKT
4
The CPU Sets This Bit, At The Same Time As The TxPktRdy Bit Is Set, To Send A SETUP Token Instead Of An OUT Token For The Transaction
FLUSHFIFO
3
The CPU Writes A 1 To This Bit To Flush The Latest Packet From The Endpoint TX FIFO
ERROR
2
This Bit Will Be Set When Three Attempts Have Been Made To Perform A Transaction With No Response From The Peripheral
UNDERRUN
2
The USB Sets This Bit If An In Token Is Received When TxPktRdy Is Not Set.
FIFONOTEMPTY
1
The USB Sets This Bit When There Is At Least 1 Packet In The TX FIFO.
TXPKTRDY
0
The CPU Sets This Bit After Loading A Data Packet Into The FIFO.
ENDPOINT0.CSR0HENDPOINT0 Additional Control And Status Bits For TX Endpoint 0
Address
0x46001013
Reset
0x00
Access
read/write
7–
6–
5–
4–
3DISPING
2DATATOGGLEWRTENABLE
1DATATOGGLE
0FLUSHFIFO
4 fields
Field
Bits
What it does
DISPING
3
The CPU Writes A 1 To This Bit To Instruct The Core Not To Issue PING Tokens In Data And Status Phases Of A High-Speed Control Transfer
DATATOGGLEWRTENABLE
2
The CPU Writes A 1 To This Bit To Enable The Current State Of The Endpoint 0 Data Toggle To Be Written
DATATOGGLE
1
When Read, This Bit Indicates The Current State Of The Endpoint 0 Data Toggle
FLUSHFIFO
0
Flush The Next Packet To Be Transmitted/Read
ENDPOINTX.TXCSRHENDPOINTX Additional Control And Status Bits For TX Endpoints 1-15
Address
0x46001013
Reset
0x00
Access
read/write
7AUTOSET
6ISO
5MODE
4DMAREQENAB
3FRCDATATOG
2DMAREQMODE
1DATATOGGLEWRENABLE
0DATATOGGLE
12 fields
Field
Bits
What it does
AUTOSET
7
If The CPU Sets This Bit, TxPktRdy Will Be Automatically Set When Data Of The Maximum P
AUTOSET
7
If The CPU Sets This Bit, TxPktRdy Will Be Automatically Set When Data Of The Maximum Packet Size Is Loaded Into The TX FIFO.
ISO
6
The CPU Sets This Bit To Enable The TX Endpoint For Isochronous Transfers
MODE
5
The CPU Sets This Bit To Enable The Endpoint Direction As TX
DMAREQENAB
4
The CPU Sets This Bit To Enable The DMA Request For The RX Endpoint
DMAREQENAB
4
The CPU Sets This Bit To Enable The DMA Request For The TX Endpoint
FRCDATATOG
3
The CPU Sets This Bit To Force The Endpoint Data Toggle To Switch And The Data Packe
FRCDATATOG
3
The CPU Sets This Bit To Force The Endpoint Data Toggle To Switch And The Data Packet To Be Cleared From The FIFO.
DMAREQMODE
2
The CPU Sets This Bit To Select DMA Request Mode
DMAREQMODE
2
The CPU Sets This Bit To Select DMA Request Mode 1 And Clears It To Select DMA Request Mode 0.
DATATOGGLEWRENABLE
1
The CPU Writes A 1 To This Bit To Enable The Current State Of The Endpoint 0 Data Toggle To Be Written
DATATOGGLE
0
When Read, This Bit Indicates The Current State Of The Endpoint
ENDPOINTX.RXMAXPENDPOINTX Maximum Amount Of Data That Can Be Transferred Through The Selected RX Endpoint In A Single Operation
Address
0x46001014
Reset
0x0000
Access
read/write
Size
16-bit
2 fields
Field
Bits
What it does
MULTIPLIER
15:11
Multiplier Value (m-1)
MAXPAYLOAD
10:0
Maximum Payload/Transactions
ENDPOINTX.RXCSRLENDPOINTX Control And Status Bits for RX Endpoint 0 Or Endpoint 1-15
Address
0x46001016
Reset
0x00
Access
read/write
7CLRDATATOG
6RXSTALL
5REQPKT
4FLUSHFIFO
3DATAERROR
2ERROR
1FIFOFULL
0RXPKTRDY
13 fields
Field
Bits
What it does
CLRDATATOG
7
The CPU Writes A 1 To This Bit To Reset The Endpoint Data Toggle To 0.
RXSTALL
6
When A STALL Handshake Is Received, This Bit Is Set And An Interrupt Is Generated.
SENTSTALL
6
This Bit Is Set When A STALL Handshake Is Transmitted.
REQPKT
5
The CPU Writes A 1 To This Bit To Request An IN Transaction.
SENDSTALL
5
The CPU Writes A 1 To This Bit To Issue A STALL Handshake.
FLUSHFIFO
4
The CPU Writes A 1 To This Bit To Flush The Next Packet To Be Read From The Endpoint Rx FIFO
DATAERROR
3
This Bit Is Set When RxPktRdy Is Set If The Data Packet Has A CRC Or Bit-stuff Error.
NAKTIMEOUT
3
This Bit Is Set When RxPktRdy Is Set If The Data Packet Has A CRC Or Bit-stuff Error.
ERROR
2
The USB Sets This Bit When 3 Attempts Have Been Made To Receive A Packet And No Data Packet Has Been Received.
OVERRUN
2
This Bit Is Set If An OUT Packet Cannot Be Loaded Into The Rx FIFO.
FIFOFULL
1
This Bit Is Set When No More Packets Can Be Loaded
FIFOFULL
1
This Bit Is Set When No More Packets Can Be Loaded Into The Rx FIFO.
RXPKTRDY
0
This Bit Is Set When A Data Packet Has Been Received.
ENDPOINTX.RXCSRHENDPOINTX Additional Control And Status Bits for RX Endpoint 0 Or Endpoint 1-15
Address
0x46001017
Reset
0x00
Access
read/write
7AUTOCLEAR
6AUTOREQ
5DMAREQENAB
4DISNYET
3DMAREQMODE
2DATATOGGLEWRTENABLE
1DATATOGGLE
0INCOMPRX
12 fields
Field
Bits
What it does
AUTOCLEAR
7
If The CPU Sets This Bit Then The RxPktRdy Bit Will Be Automatically Cleared Whean A Packet Of RxMaxP Bytes Has Benn Unloaded Froim The Rx FIFO
AUTOCLEAR
7
If The CPU Sets This Bit, TxPktRdy Will Be Automatically Cleared When A Packet Of RxMaxP Bytes Has Been Unloaded From The RX FIFO
AUTOREQ
6
If The CPU Sets This Bit, The ReqPkt Bit Will Be Automatically Set When The RxPktRdy Bit Is Cleared.
ISO
6
The CPU Sets This Bit To Enable the RX Endpoint For Isochronous Transfers
DMAREQENAB
5
The CPU Sets This Bit To Enable The DMA Request For The RX Endpoint
DISNYET
4
The CPU Sets This Bit To Disable The Sending Of NYET Handshakes
PIDERROR
4
Indicates A PID Error In The Received Packet
DMAREQMODE
3
The CPU Sets This Bit To Select DMA Request Mode
DATATOGGLEWRTENABLE
2
The CPU Writes A 1 To This Bit To Enable The Current State Of The Endpoint 0 Data Toggle To Be Written
DATATOGGLE
1
When Read, This Bit Indicates The Current State Of The Endpoint
INCOMPRX
0
This Bit Is Set In A High-Bandwidth Isochronous/Interrupt Transfer If The Packet In The Rx FIFO Is Incomplete
INCOMPRX
0
This Bit Is Set In A High-Bandwidth Isochronous/Interrupt Transfer If The Packet In The Rx FIFO Is Incomplete Because Parts Of The Data Were Not Received.
ENDPOINT0.COUNT0ENDPOINT0 Number Of Received Bytes In Endpoint 0 FIFO
Address
0x46001018
Reset
0x00
Access
read only
7–
6EP0RXCOUNT6
5EP0RXCOUNT5
4EP0RXCOUNT4
3EP0RXCOUNT3
2EP0RXCOUNT2
1EP0RXCOUNT1
0EP0RXCOUNT0
1 field
Field
Bits
What it does
EP0RXCOUNT
6:0
Number Of Received Data Bytes In Endpoint 0 FIFO
ENDPOINTX.RXCOUNTENDPOINTX Number Of Data Bytes In The Packet Currently In Line To Be Read From The RX FIFO.
Address
0x46001018
Reset
0x0000
Access
read only
Size
16-bit
1 field
Field
Bits
What it does
ENDPOINTRXCOUNT
13:0
Number Of Data Bytes In The Packet Currently In Line To Be Read From The RX FIFO.
ENDPOINT0.TYPE0ENDPOINT0 Host Mode Only: Operating Speed Of The Targeted Device
Address
0x4600101A
Reset
0x00
Access
read/write
7SPEED1
6SPEED0
5–
4–
3–
2–
1–
0–
1 field
Field
Bits
What it does
SPEED
7:6
Operating Speed Of The Target Device
1 Device In High Speed
2 Device In Full Speed
3 Device In Low Speed
ENDPOINTX.TXTYPEENDPOINTX Host Mode Only: Should Be Written With The Endpoint Number To Be Targeted By The Endpoint
Address
0x4600101A
Reset
0x00
Access
read/write
7SPEED1
6SPEED0
5PROTOCOL1
4PROTOCOL0
3ENDPOINTNUMBER3
2ENDPOINTNUMBER2
1ENDPOINTNUMBER1
0ENDPOINTNUMBER0
3 fields
Field
Bits
What it does
SPEED
7:6
operating speed of the target device when the core is configured with the multipoint option: 00: unused (note: if selected, the target will be assumed to be using the same connection speed as the core.) 01: high 10: full 11: low
1 Device In High Speed
2 Device In Full Speed
3 Device In Low Speed
PROTOCOL
5:4
the cpu should set this to select the required protocol for the tx endpoint 00: control 01: isochronous 10: bulk 11: interrupt
0
1
2
3
ENDPOINTNUMBER
3:0
the cpu should set this value to the endpoint number contained in the tx endpoint descriptor
ENDPOINT0.NAKLIMIT0ENDPOINT0 Host Mode Only: Sets The NAK Response Timeout On Endpoint 0.
Address
0x4600101B
Reset
0x00
Access
read/write
7–
6–
5–
4EP0NAKLIMIT4
3EP0NAKLIMIT3
2EP0NAKLIMIT2
1EP0NAKLIMIT1
0EP0NAKLIMIT0
1 field
Field
Bits
What it does
EP0NAKLIMIT
4:0
Number Of Frames/Microframes After Which Endpoint 0 Should Timeout
ENDPOINTX.TXINTERVALENDPOINTX Host Mode Only: Defines The Polling Interval For The Currently Selected TX Endpoint.
Address
0x4600101B
Reset
0x00
Access
read/write
7TXPOLLINGINTERVAL7
6TXPOLLINGINTERVAL6
5TXPOLLINGINTERVAL5
4TXPOLLINGINTERVAL4
3TXPOLLINGINTERVAL3
2TXPOLLINGINTERVAL2
1TXPOLLINGINTERVAL1
0TXPOLLINGINTERVAL0
1 field
Field
Bits
What it does
TXPOLLINGINTERVAL
7:0
polling interval
ENDPOINTX.RXTYPEENDPOINTX Host Mode Only: Should Be Written With The Endpoint Number To Be Targeted By The Endpoint
Address
0x4600101C
Reset
0x00
Access
read/write
7SPEED1
6SPEED0
5PROTOCOL1
4PROTOCOL0
3ENDPOINTNUMBER3
2ENDPOINTNUMBER2
1ENDPOINTNUMBER1
0ENDPOINTNUMBER0
3 fields
Field
Bits
What it does
SPEED
7:6
operating speed of the target device when the core is configured with the multipoint option: 00: unused (note: if selected, the target will be assumed to be using the same connection speed as the core.) 01: high 10: full 11: low
0
1
2
3
PROTOCOL
5:4
the cpu should set this to select the required protocol for the rx endpoint 00: control 01: isochronous 10: bulk 11: interrupt
0
1
2
3
ENDPOINTNUMBER
3:0
the cpu should set this value to the endpoint number contained in the rx endpoint descriptor returned to the musbmhdrc during device enumeration.
ENDPOINTX.RXINTERVALENDPOINTX Host Mode Only: Defines The Polling Interval For The Currently Selected RX Endpoint.
Address
0x4600101D
Reset
0x00
Access
read/write
7RXPOLLINGINTERVAL7
6RXPOLLINGINTERVAL6
5RXPOLLINGINTERVAL5
4RXPOLLINGINTERVAL4
3RXPOLLINGINTERVAL3
2RXPOLLINGINTERVAL2
1RXPOLLINGINTERVAL1
0RXPOLLINGINTERVAL0
1 field
Field
Bits
What it does
RXPOLLINGINTERVAL
7:0
polling interval
ENDPOINT0.CONFIGDATAENDPOINT0 Returns Information About The Selected Core Configuration. Only Applicable when INDEX Regsiter Is 0. That Is Endpoint0 Is Selected.
Address
0x4600101F
Reset
0x00
Access
read only
7MPRXE
6MPTXE
5BIGENDIAN
4HBRXE
3HBTXE
2DYNFIFOSIZING
1SOFTCONE
0UTMIDATAWIDTH
8 fields
Field
Bits
What it does
MPRXE
7
Automatic Splitting Of Bulk Amalgamation Is Selected
MPTXE
6
Automatic Splitting Of Bulk Packets Is Selected
BIGENDIAN
5
Indicates Little Endian Ordering
HBRXE
4
Indicates High Bandwidth RX ISO Endpoint Support Selected
HBTXE
3
Indicates High Bandwidth TX ISO Endpoint Support Selected
ENDPOINTX.FIFOSIZEENDPOINTX Read Only Register That Returns The Sizes Of The FIFO's Associated With The Selected Additional TX/RX Endpoints. INDEX Regsiter should be set 1-15
Address
0x4600101F
Reset
0x00
Access
read only
7RXFIFOSIZE3
6RXFIFOSIZE2
5RXFIFOSIZE1
4RXFIFOSIZE0
3TXFIFOSIZE3
2TXFIFOSIZE2
1TXFIFOSIZE1
0TXFIFOSIZE0
2 fields
Field
Bits
What it does
RXFIFOSIZE
7:4
Rx FIFO Size
TXFIFOSIZE
3:0
Tx FIFO Size
FIFOX0Address Range Provides 16 Addresses For CPU Access To The FIFO's For Each Endpoint
Address
0x46001020
Reset
0x00000000
Access
read/write
Size
32-bit
1 field
Field
Bits
What it does
FIFOADDR
31:0
Writing To These Addresses Loads Data Into The TXFIFO For The Corresponding Endpoint
FIFOX1Address Range Provides 16 Addresses For CPU Access To The FIFO's For Each Endpoint
Address
0x46001024
Reset
0x00000000
Access
read/write
Size
32-bit
1 field
Field
Bits
What it does
FIFOADDR
31:0
Writing To These Addresses Loads Data Into The TXFIFO For The Corresponding Endpoint
FIFOX2Address Range Provides 16 Addresses For CPU Access To The FIFO's For Each Endpoint
Address
0x46001028
Reset
0x00000000
Access
read/write
Size
32-bit
1 field
Field
Bits
What it does
FIFOADDR
31:0
Writing To These Addresses Loads Data Into The TXFIFO For The Corresponding Endpoint
FIFOX3Address Range Provides 16 Addresses For CPU Access To The FIFO's For Each Endpoint
Address
0x4600102C
Reset
0x00000000
Access
read/write
Size
32-bit
1 field
Field
Bits
What it does
FIFOADDR
31:0
Writing To These Addresses Loads Data Into The TXFIFO For The Corresponding Endpoint
FIFOX4Address Range Provides 16 Addresses For CPU Access To The FIFO's For Each Endpoint
Address
0x46001030
Reset
0x00000000
Access
read/write
Size
32-bit
1 field
Field
Bits
What it does
FIFOADDR
31:0
Writing To These Addresses Loads Data Into The TXFIFO For The Corresponding Endpoint
FIFOX5Address Range Provides 16 Addresses For CPU Access To The FIFO's For Each Endpoint
Address
0x46001034
Reset
0x00000000
Access
read/write
Size
32-bit
1 field
Field
Bits
What it does
FIFOADDR
31:0
Writing To These Addresses Loads Data Into The TXFIFO For The Corresponding Endpoint
FIFOX6Address Range Provides 16 Addresses For CPU Access To The FIFO's For Each Endpoint
Address
0x46001038
Reset
0x00000000
Access
read/write
Size
32-bit
1 field
Field
Bits
What it does
FIFOADDR
31:0
Writing To These Addresses Loads Data Into The TXFIFO For The Corresponding Endpoint
FIFOX7Address Range Provides 16 Addresses For CPU Access To The FIFO's For Each Endpoint
Address
0x4600103C
Reset
0x00000000
Access
read/write
Size
32-bit
1 field
Field
Bits
What it does
FIFOADDR
31:0
Writing To These Addresses Loads Data Into The TXFIFO For The Corresponding Endpoint
DEVCTLSelects Whether The Core Is Operating In Peripheral Or Host Mode
Address
0x46001060
Reset
0x80
Access
read/write
7BDEVICE
6FSDEV
5LSDEV
4VBUS1
3VBUS0
2HOSTMODE
1HOSTREQ
0SESSION
7 fields
Field
Bits
What it does
BDEVICE
7
indicates whether the core is operating as a 'A' device or 'B' device
FSDEV
6
host mode only: this bit is set when a full or high speed device has been detected being connected to the port
LSDEV
5
host mode only: this bit is set when a low speed device has been detected being connected to the port
VBUS
4:3
encoded value for the VBus level
0 Below SessionEnd
1 Above SessionEnd, below AValid
2 Above AValid, below VBus Valid
3 Above VBusValid
HOSTMODE
2
this read-only bit is set when the USBCORE is acting as a host
HOSTREQ
1
when set, the USBCORE will initiate the host negotiation when suspend mode is entered.
SESSION
0
when operating as an 'A' device, this bit is set or cleared by CPU to state or end a session. when operating as a 'B' device, this bit is set/cleared by the USBCORE when a session starts/ends
MISCRX/TX Early DMA Enable Bits
Address
0x46001061
Reset
0x00
Access
read/write
7–
6–
5–
4–
3–
2–
1TXEDMA
0RXEDMA
2 fields
Field
Bits
What it does
TXEDMA
1
DMA_REQ signal for all IN endpoints will be deasserted based on this bit selection
0 Dma_req signal for all in endpoints will be de-asserted when maxp bytes have been written to an endpoint. this is late mode.
1 Dma_req signal for all in endpoints will be de-asserted when maxp-8 bytes have been written to an endpoint. this is early mode.
RXEDMA
0
DMA_REQ signal for all OUT endpoints will be deasserted based on this bit selection
0 Dma_req signal for all out endpoints will be de-asserted when maxp bytes have been written to an endpoint. this is late mode.
1 Dma_req signal for all out endpoints will be de-asserted when maxp-8 bytes have been written to an endpoint. this is early mode.
TXFIFOSZControls The Size Of The Selected TX Endpoint FIFO
Address
0x46001062
Reset
0x00
Access
read/write
7–
6–
5–
4DPB
3SZ3
2SZ2
1SZ1
0SZ0
2 fields
Field
Bits
What it does
DPB
4
double packet buffering supported or not
SZ
3:0
maximum packet size to be allowed
0 8 BYTES
1 16 BYTES
2 32 BYTES
3 64 BYTES
4 128 BYTES
5 256 BYTES
6 512 BYTES
7 1024 BYTES
8 2048 BYTES
9 4096 BYTES
RXFIFOSZControls The Size Of The Selected RX Endpoint FIFO
Address
0x46001063
Reset
0x00
Access
read/write
7–
6–
5–
4DPB
3SZ3
2SZ2
1SZ1
0SZ0
2 fields
Field
Bits
What it does
DPB
4
double packet buffering enabled or not
SZ
3:0
maximum packet size to be allowed
0 8 BYTES
1 16 BYTES
2 32 BYTES
3 64 BYTES
4 128 BYTES
5 256 BYTES
6 512 BYTES
7 1024 BYTES
8 2048 BYTES
9 4096 BYTES
TXFIFOADDControls The Start Address Of the Selected TX Endpoint FIFO
Address
0x46001064
Reset
0x0000
Access
read/write
Size
16-bit
1 field
Field
Bits
What it does
ADDR
12:0
start address of the endpoint FIFO
RXFIFOADDControls The Start Address Of the Selected RX Endpoint FIFO
Address
0x46001066
Reset
0x0000
Access
read/write
Size
16-bit
1 field
Field
Bits
What it does
ADDR
12:0
start address of the endpoint FIFO
EPINFOAllows Read-Back Of The Number Of TX And RX Endpoints
Address
0x46001078
Reset
0xFF
Access
read only
7RXENDPOINTS3
6RXENDPOINTS2
5RXENDPOINTS1
4RXENDPOINTS0
3TXENDPOINTS3
2TXENDPOINTS2
1TXENDPOINTS1
0TXENDPOINTS0
2 fields
Field
Bits
What it does
RXENDPOINTS
7:4
number of rx endpoints
TXENDPOINTS
3:0
number of tx endpoints
RAMINFODetails About Width Of RAM and DMA Channels
Address
0x46001079
Reset
0x8D
Access
read only
7DMACHANS3
6DMACHANS2
5DMACHANS1
4DMACHANS0
3RAMBITS3
2RAMBITS2
1RAMBITS1
0RAMBITS0
2 fields
Field
Bits
What it does
DMACHANS
7:4
number of dma channels implemented in the design
RAMBITS
3:0
width of the ram address bus
LINKINFOAllows Some Delays To Be Specified
Address
0x4600107A
Reset
0x5C
Access
read/write
7WTCON3
6WTCON2
5WTCON1
4WTCON0
3WTID3
2WTID2
1WTID1
0WTID0
2 fields
Field
Bits
What it does
WTCON
7:4
sets the wait to be applied to allow for the user's connect/disconnect filter in units of 533.3ns
WTID
3:0
sets the delay to be applied from idpullup being asserted to iddig being considered valid in units of 4.369ms
VPLENSets The Duration Of The VBus Pulsing Charge
Address
0x4600107B
Reset
0x3C
Access
read/write
7VPLEN7
6VPLEN6
5VPLEN5
4VPLEN4
3VPLEN3
2VPLEN2
1VPLEN1
0VPLEN0
1 field
Field
Bits
What it does
VPLEN
7:0
duration of VBus pulsing charge in units of 546.1us
HSEOF1Sets The Minimum Time Gap That Is To Be Allowed Between The Start Of The Last Transaction And The EOF For HS Transactions
Address
0x4600107C
Reset
0x80
Access
read/write
7HSEOF17
6HSEOF16
5HSEOF15
4HSEOF14
3HSEOF13
2HSEOF12
1HSEOF11
0HSEOF10
1 field
Field
Bits
What it does
HSEOF1
7:0
sets for high-speed transactions the time before eof to stop beginning new transactions, in units of 133.3ns. (the default setting corresponds to 17.07us.)
FSEOF1Sets The Minimum Time Gap That Is To Be Allowed Between The Start Of The Last Transaction And The EOF For FS Transactions
Address
0x4600107D
Reset
0x77
Access
read/write
7FSEOF17
6FSEOF16
5FSEOF15
4FSEOF14
3FSEOF13
2FSEOF12
1FSEOF11
0FSEOF10
1 field
Field
Bits
What it does
FSEOF1
7:0
sets for full-speed transactions the time before eof to stop beginning new transactions, in units of 533.3ns. (the default setting corresponds to 63.46us.)
LSEOF1Sets The Minimum Time Gap That Is To Be Allowed Between The Start Of The Last Transaction And The EOF For LS Transactions
Address
0x4600107E
Reset
0x72
Access
read/write
7LSEOF17
6LSEOF16
5LSEOF15
4LSEOF14
3LSEOF13
2LSEOF12
1LSEOF11
0LSEOF10
1 field
Field
Bits
What it does
LSEOF1
7:0
sets for low-speed transactions the time before eof to stop beginning new transactions, in units of 1.067us. (the default setting corresponds to 121.6us.)
SOFTRSTAssert Low The Output Reset Signals NRSTO and NRSTXO
Address
0x4600107F
Reset
0x00
Access
read/write
7–
6–
5–
4–
3–
2–
1NRSTX
0NRST
2 fields
Field
Bits
What it does
NRSTX
1
when a 1 is written to this bit, the output nrstxo will be asserted (low) within a minimum delay of 7 cycles of the clk input. the output nrstxo will be asynchronously asserted and synchronously de-asserted with respect to xclk.
NRST
0
when a 1 is written to this bit, the output nrsto will be asserted (low) within a minimum delay of 7 cycles of the clk input. the output nrsto will be asynchronously asserted and synchronously de-asserted with respect to clk.
TXFUNADDR0.TXFUNCADDREPRelevant In Host Mode Only. Address Of The Target Function.
Address
0x46001080
Reset
0x00
Access
read/write
7–
6TXFUNCADDR6
5TXFUNCADDR5
4TXFUNCADDR4
3TXFUNCADDR3
2TXFUNCADDR2
1TXFUNCADDR1
0TXFUNCADDR0
1 field
Field
Bits
What it does
TXFUNCADDR
6:0
address of the target function
TXFUNADDR0.TXHUBADDREPRelevant In Host Mode Only. HUB Address
Address
0x46001082
Reset
0x00
Access
read/write
7MULTRANS
6TXHUBADDR6
5TXHUBADDR5
4TXHUBADDR4
3TXHUBADDR3
2TXHUBADDR2
1TXHUBADDR1
0TXHUBADDR0
2 fields
Field
Bits
What it does
MULTRANS
7
hub has multiple or single translator
TXHUBADDR
6:0
hub address
TXFUNADDR0.TXHUBPORTRelevant In Host Mode Only. HUB Address
Address
0x46001083
Reset
0x00
Access
read/write
7–
6HUBPORT6
5HUBPORT5
4HUBPORT4
3HUBPORT3
2HUBPORT2
1HUBPORT1
0HUBPORT0
1 field
Field
Bits
What it does
HUBPORT
6:0
Hub Port
TXFUNADDR0.RXFUNCADDREPRelevant In Host Mode Only. Address Of The Target Function.
Address
0x46001084
Reset
0x00
Access
read/write
7–
6RXFUNCADDR6
5RXFUNCADDR5
4RXFUNCADDR4
3RXFUNCADDR3
2RXFUNCADDR2
1RXFUNCADDR1
0RXFUNCADDR0
1 field
Field
Bits
What it does
RXFUNCADDR
6:0
address of the target function
TXFUNADDR0.RXHUBADDREPRelevant In Host Mode Only. HUB Address
Address
0x46001086
Reset
0x00
Access
read/write
7MULTRANS
6RXHUBADDR6
5RXHUBADDR5
4RXHUBADDR4
3RXHUBADDR3
2RXHUBADDR2
1RXHUBADDR1
0RXHUBADDR0
2 fields
Field
Bits
What it does
MULTRANS
7
hub has multiple or single translator
RXHUBADDR
6:0
hub address
TXFUNADDR0.RXHUBPORTRelevant In Host Mode Only. HUB Address
Address
0x46001087
Reset
0x00
Access
read/write
7–
6HUBPORT6
5HUBPORT5
4HUBPORT4
3HUBPORT3
2HUBPORT2
1HUBPORT1
0HUBPORT0
1 field
Field
Bits
What it does
HUBPORT
6:0
Hub Port
TXFUNADDR1.TXFUNCADDREPRelevant In Host Mode Only. Address Of The Target Function.
Address
0x46001088
Reset
0x00
Access
read/write
7–
6TXFUNCADDR6
5TXFUNCADDR5
4TXFUNCADDR4
3TXFUNCADDR3
2TXFUNCADDR2
1TXFUNCADDR1
0TXFUNCADDR0
1 field
Field
Bits
What it does
TXFUNCADDR
6:0
address of the target function
TXFUNADDR1.TXHUBADDREPRelevant In Host Mode Only. HUB Address
Address
0x4600108A
Reset
0x00
Access
read/write
7MULTRANS
6TXHUBADDR6
5TXHUBADDR5
4TXHUBADDR4
3TXHUBADDR3
2TXHUBADDR2
1TXHUBADDR1
0TXHUBADDR0
2 fields
Field
Bits
What it does
MULTRANS
7
hub has multiple or single translator
TXHUBADDR
6:0
hub address
TXFUNADDR1.TXHUBPORTRelevant In Host Mode Only. HUB Address
Address
0x4600108B
Reset
0x00
Access
read/write
7–
6HUBPORT6
5HUBPORT5
4HUBPORT4
3HUBPORT3
2HUBPORT2
1HUBPORT1
0HUBPORT0
1 field
Field
Bits
What it does
HUBPORT
6:0
Hub Port
TXFUNADDR1.RXFUNCADDREPRelevant In Host Mode Only. Address Of The Target Function.
Address
0x4600108C
Reset
0x00
Access
read/write
7–
6RXFUNCADDR6
5RXFUNCADDR5
4RXFUNCADDR4
3RXFUNCADDR3
2RXFUNCADDR2
1RXFUNCADDR1
0RXFUNCADDR0
1 field
Field
Bits
What it does
RXFUNCADDR
6:0
address of the target function
TXFUNADDR1.RXHUBADDREPRelevant In Host Mode Only. HUB Address
Address
0x4600108E
Reset
0x00
Access
read/write
7MULTRANS
6RXHUBADDR6
5RXHUBADDR5
4RXHUBADDR4
3RXHUBADDR3
2RXHUBADDR2
1RXHUBADDR1
0RXHUBADDR0
2 fields
Field
Bits
What it does
MULTRANS
7
hub has multiple or single translator
RXHUBADDR
6:0
hub address
TXFUNADDR1.RXHUBPORTRelevant In Host Mode Only. HUB Address
Address
0x4600108F
Reset
0x00
Access
read/write
7–
6HUBPORT6
5HUBPORT5
4HUBPORT4
3HUBPORT3
2HUBPORT2
1HUBPORT1
0HUBPORT0
1 field
Field
Bits
What it does
HUBPORT
6:0
Hub Port
TXFUNADDR2.TXFUNCADDREPRelevant In Host Mode Only. Address Of The Target Function.
Address
0x46001090
Reset
0x00
Access
read/write
7–
6TXFUNCADDR6
5TXFUNCADDR5
4TXFUNCADDR4
3TXFUNCADDR3
2TXFUNCADDR2
1TXFUNCADDR1
0TXFUNCADDR0
1 field
Field
Bits
What it does
TXFUNCADDR
6:0
address of the target function
TXFUNADDR2.TXHUBADDREPRelevant In Host Mode Only. HUB Address
Address
0x46001092
Reset
0x00
Access
read/write
7MULTRANS
6TXHUBADDR6
5TXHUBADDR5
4TXHUBADDR4
3TXHUBADDR3
2TXHUBADDR2
1TXHUBADDR1
0TXHUBADDR0
2 fields
Field
Bits
What it does
MULTRANS
7
hub has multiple or single translator
TXHUBADDR
6:0
hub address
TXFUNADDR2.TXHUBPORTRelevant In Host Mode Only. HUB Address
Address
0x46001093
Reset
0x00
Access
read/write
7–
6HUBPORT6
5HUBPORT5
4HUBPORT4
3HUBPORT3
2HUBPORT2
1HUBPORT1
0HUBPORT0
1 field
Field
Bits
What it does
HUBPORT
6:0
Hub Port
TXFUNADDR2.RXFUNCADDREPRelevant In Host Mode Only. Address Of The Target Function.
Address
0x46001094
Reset
0x00
Access
read/write
7–
6RXFUNCADDR6
5RXFUNCADDR5
4RXFUNCADDR4
3RXFUNCADDR3
2RXFUNCADDR2
1RXFUNCADDR1
0RXFUNCADDR0
1 field
Field
Bits
What it does
RXFUNCADDR
6:0
address of the target function
TXFUNADDR2.RXHUBADDREPRelevant In Host Mode Only. HUB Address
Address
0x46001096
Reset
0x00
Access
read/write
7MULTRANS
6RXHUBADDR6
5RXHUBADDR5
4RXHUBADDR4
3RXHUBADDR3
2RXHUBADDR2
1RXHUBADDR1
0RXHUBADDR0
2 fields
Field
Bits
What it does
MULTRANS
7
hub has multiple or single translator
RXHUBADDR
6:0
hub address
TXFUNADDR2.RXHUBPORTRelevant In Host Mode Only. HUB Address
Address
0x46001097
Reset
0x00
Access
read/write
7–
6HUBPORT6
5HUBPORT5
4HUBPORT4
3HUBPORT3
2HUBPORT2
1HUBPORT1
0HUBPORT0
1 field
Field
Bits
What it does
HUBPORT
6:0
Hub Port
TXFUNADDR3.TXFUNCADDREPRelevant In Host Mode Only. Address Of The Target Function.
Address
0x46001098
Reset
0x00
Access
read/write
7–
6TXFUNCADDR6
5TXFUNCADDR5
4TXFUNCADDR4
3TXFUNCADDR3
2TXFUNCADDR2
1TXFUNCADDR1
0TXFUNCADDR0
1 field
Field
Bits
What it does
TXFUNCADDR
6:0
address of the target function
TXFUNADDR3.TXHUBADDREPRelevant In Host Mode Only. HUB Address
Address
0x4600109A
Reset
0x00
Access
read/write
7MULTRANS
6TXHUBADDR6
5TXHUBADDR5
4TXHUBADDR4
3TXHUBADDR3
2TXHUBADDR2
1TXHUBADDR1
0TXHUBADDR0
2 fields
Field
Bits
What it does
MULTRANS
7
hub has multiple or single translator
TXHUBADDR
6:0
hub address
TXFUNADDR3.TXHUBPORTRelevant In Host Mode Only. HUB Address
Address
0x4600109B
Reset
0x00
Access
read/write
7–
6HUBPORT6
5HUBPORT5
4HUBPORT4
3HUBPORT3
2HUBPORT2
1HUBPORT1
0HUBPORT0
1 field
Field
Bits
What it does
HUBPORT
6:0
Hub Port
TXFUNADDR3.RXFUNCADDREPRelevant In Host Mode Only. Address Of The Target Function.
Address
0x4600109C
Reset
0x00
Access
read/write
7–
6RXFUNCADDR6
5RXFUNCADDR5
4RXFUNCADDR4
3RXFUNCADDR3
2RXFUNCADDR2
1RXFUNCADDR1
0RXFUNCADDR0
1 field
Field
Bits
What it does
RXFUNCADDR
6:0
address of the target function
TXFUNADDR3.RXHUBADDREPRelevant In Host Mode Only. HUB Address
Address
0x4600109E
Reset
0x00
Access
read/write
7MULTRANS
6RXHUBADDR6
5RXHUBADDR5
4RXHUBADDR4
3RXHUBADDR3
2RXHUBADDR2
1RXHUBADDR1
0RXHUBADDR0
2 fields
Field
Bits
What it does
MULTRANS
7
hub has multiple or single translator
RXHUBADDR
6:0
hub address
TXFUNADDR3.RXHUBPORTRelevant In Host Mode Only. HUB Address
Address
0x4600109F
Reset
0x00
Access
read/write
7–
6HUBPORT6
5HUBPORT5
4HUBPORT4
3HUBPORT3
2HUBPORT2
1HUBPORT1
0HUBPORT0
1 field
Field
Bits
What it does
HUBPORT
6:0
Hub Port
TXFUNADDR4.TXFUNCADDREPRelevant In Host Mode Only. Address Of The Target Function.
Address
0x460010A0
Reset
0x00
Access
read/write
7–
6TXFUNCADDR6
5TXFUNCADDR5
4TXFUNCADDR4
3TXFUNCADDR3
2TXFUNCADDR2
1TXFUNCADDR1
0TXFUNCADDR0
1 field
Field
Bits
What it does
TXFUNCADDR
6:0
address of the target function
TXFUNADDR4.TXHUBADDREPRelevant In Host Mode Only. HUB Address
Address
0x460010A2
Reset
0x00
Access
read/write
7MULTRANS
6TXHUBADDR6
5TXHUBADDR5
4TXHUBADDR4
3TXHUBADDR3
2TXHUBADDR2
1TXHUBADDR1
0TXHUBADDR0
2 fields
Field
Bits
What it does
MULTRANS
7
hub has multiple or single translator
TXHUBADDR
6:0
hub address
TXFUNADDR4.TXHUBPORTRelevant In Host Mode Only. HUB Address
Address
0x460010A3
Reset
0x00
Access
read/write
7–
6HUBPORT6
5HUBPORT5
4HUBPORT4
3HUBPORT3
2HUBPORT2
1HUBPORT1
0HUBPORT0
1 field
Field
Bits
What it does
HUBPORT
6:0
Hub Port
TXFUNADDR4.RXFUNCADDREPRelevant In Host Mode Only. Address Of The Target Function.
Address
0x460010A4
Reset
0x00
Access
read/write
7–
6RXFUNCADDR6
5RXFUNCADDR5
4RXFUNCADDR4
3RXFUNCADDR3
2RXFUNCADDR2
1RXFUNCADDR1
0RXFUNCADDR0
1 field
Field
Bits
What it does
RXFUNCADDR
6:0
address of the target function
TXFUNADDR4.RXHUBADDREPRelevant In Host Mode Only. HUB Address
Address
0x460010A6
Reset
0x00
Access
read/write
7MULTRANS
6RXHUBADDR6
5RXHUBADDR5
4RXHUBADDR4
3RXHUBADDR3
2RXHUBADDR2
1RXHUBADDR1
0RXHUBADDR0
2 fields
Field
Bits
What it does
MULTRANS
7
hub has multiple or single translator
RXHUBADDR
6:0
hub address
TXFUNADDR4.RXHUBPORTRelevant In Host Mode Only. HUB Address
Address
0x460010A7
Reset
0x00
Access
read/write
7–
6HUBPORT6
5HUBPORT5
4HUBPORT4
3HUBPORT3
2HUBPORT2
1HUBPORT1
0HUBPORT0
1 field
Field
Bits
What it does
HUBPORT
6:0
Hub Port
TXFUNADDR5.TXFUNCADDREPRelevant In Host Mode Only. Address Of The Target Function.
Address
0x460010A8
Reset
0x00
Access
read/write
7–
6TXFUNCADDR6
5TXFUNCADDR5
4TXFUNCADDR4
3TXFUNCADDR3
2TXFUNCADDR2
1TXFUNCADDR1
0TXFUNCADDR0
1 field
Field
Bits
What it does
TXFUNCADDR
6:0
address of the target function
TXFUNADDR5.TXHUBADDREPRelevant In Host Mode Only. HUB Address
Address
0x460010AA
Reset
0x00
Access
read/write
7MULTRANS
6TXHUBADDR6
5TXHUBADDR5
4TXHUBADDR4
3TXHUBADDR3
2TXHUBADDR2
1TXHUBADDR1
0TXHUBADDR0
2 fields
Field
Bits
What it does
MULTRANS
7
hub has multiple or single translator
TXHUBADDR
6:0
hub address
TXFUNADDR5.TXHUBPORTRelevant In Host Mode Only. HUB Address
Address
0x460010AB
Reset
0x00
Access
read/write
7–
6HUBPORT6
5HUBPORT5
4HUBPORT4
3HUBPORT3
2HUBPORT2
1HUBPORT1
0HUBPORT0
1 field
Field
Bits
What it does
HUBPORT
6:0
Hub Port
TXFUNADDR5.RXFUNCADDREPRelevant In Host Mode Only. Address Of The Target Function.
Address
0x460010AC
Reset
0x00
Access
read/write
7–
6RXFUNCADDR6
5RXFUNCADDR5
4RXFUNCADDR4
3RXFUNCADDR3
2RXFUNCADDR2
1RXFUNCADDR1
0RXFUNCADDR0
1 field
Field
Bits
What it does
RXFUNCADDR
6:0
address of the target function
TXFUNADDR5.RXHUBADDREPRelevant In Host Mode Only. HUB Address
Address
0x460010AE
Reset
0x00
Access
read/write
7MULTRANS
6RXHUBADDR6
5RXHUBADDR5
4RXHUBADDR4
3RXHUBADDR3
2RXHUBADDR2
1RXHUBADDR1
0RXHUBADDR0
2 fields
Field
Bits
What it does
MULTRANS
7
hub has multiple or single translator
RXHUBADDR
6:0
hub address
TXFUNADDR5.RXHUBPORTRelevant In Host Mode Only. HUB Address
Address
0x460010AF
Reset
0x00
Access
read/write
7–
6HUBPORT6
5HUBPORT5
4HUBPORT4
3HUBPORT3
2HUBPORT2
1HUBPORT1
0HUBPORT0
1 field
Field
Bits
What it does
HUBPORT
6:0
Hub Port
TXFUNADDR6.TXFUNCADDREPRelevant In Host Mode Only. Address Of The Target Function.
Address
0x460010B0
Reset
0x00
Access
read/write
7–
6TXFUNCADDR6
5TXFUNCADDR5
4TXFUNCADDR4
3TXFUNCADDR3
2TXFUNCADDR2
1TXFUNCADDR1
0TXFUNCADDR0
1 field
Field
Bits
What it does
TXFUNCADDR
6:0
address of the target function
TXFUNADDR6.TXHUBADDREPRelevant In Host Mode Only. HUB Address
Address
0x460010B2
Reset
0x00
Access
read/write
7MULTRANS
6TXHUBADDR6
5TXHUBADDR5
4TXHUBADDR4
3TXHUBADDR3
2TXHUBADDR2
1TXHUBADDR1
0TXHUBADDR0
2 fields
Field
Bits
What it does
MULTRANS
7
hub has multiple or single translator
TXHUBADDR
6:0
hub address
TXFUNADDR6.TXHUBPORTRelevant In Host Mode Only. HUB Address
Address
0x460010B3
Reset
0x00
Access
read/write
7–
6HUBPORT6
5HUBPORT5
4HUBPORT4
3HUBPORT3
2HUBPORT2
1HUBPORT1
0HUBPORT0
1 field
Field
Bits
What it does
HUBPORT
6:0
Hub Port
TXFUNADDR6.RXFUNCADDREPRelevant In Host Mode Only. Address Of The Target Function.
Address
0x460010B4
Reset
0x00
Access
read/write
7–
6RXFUNCADDR6
5RXFUNCADDR5
4RXFUNCADDR4
3RXFUNCADDR3
2RXFUNCADDR2
1RXFUNCADDR1
0RXFUNCADDR0
1 field
Field
Bits
What it does
RXFUNCADDR
6:0
address of the target function
TXFUNADDR6.RXHUBADDREPRelevant In Host Mode Only. HUB Address
Address
0x460010B6
Reset
0x00
Access
read/write
7MULTRANS
6RXHUBADDR6
5RXHUBADDR5
4RXHUBADDR4
3RXHUBADDR3
2RXHUBADDR2
1RXHUBADDR1
0RXHUBADDR0
2 fields
Field
Bits
What it does
MULTRANS
7
hub has multiple or single translator
RXHUBADDR
6:0
hub address
TXFUNADDR6.RXHUBPORTRelevant In Host Mode Only. HUB Address
Address
0x460010B7
Reset
0x00
Access
read/write
7–
6HUBPORT6
5HUBPORT5
4HUBPORT4
3HUBPORT3
2HUBPORT2
1HUBPORT1
0HUBPORT0
1 field
Field
Bits
What it does
HUBPORT
6:0
Hub Port
TXFUNADDR7.TXFUNCADDREPRelevant In Host Mode Only. Address Of The Target Function.
Address
0x460010B8
Reset
0x00
Access
read/write
7–
6TXFUNCADDR6
5TXFUNCADDR5
4TXFUNCADDR4
3TXFUNCADDR3
2TXFUNCADDR2
1TXFUNCADDR1
0TXFUNCADDR0
1 field
Field
Bits
What it does
TXFUNCADDR
6:0
address of the target function
TXFUNADDR7.TXHUBADDREPRelevant In Host Mode Only. HUB Address
Address
0x460010BA
Reset
0x00
Access
read/write
7MULTRANS
6TXHUBADDR6
5TXHUBADDR5
4TXHUBADDR4
3TXHUBADDR3
2TXHUBADDR2
1TXHUBADDR1
0TXHUBADDR0
2 fields
Field
Bits
What it does
MULTRANS
7
hub has multiple or single translator
TXHUBADDR
6:0
hub address
TXFUNADDR7.TXHUBPORTRelevant In Host Mode Only. HUB Address
Address
0x460010BB
Reset
0x00
Access
read/write
7–
6HUBPORT6
5HUBPORT5
4HUBPORT4
3HUBPORT3
2HUBPORT2
1HUBPORT1
0HUBPORT0
1 field
Field
Bits
What it does
HUBPORT
6:0
Hub Port
TXFUNADDR7.RXFUNCADDREPRelevant In Host Mode Only. Address Of The Target Function.
Address
0x460010BC
Reset
0x00
Access
read/write
7–
6RXFUNCADDR6
5RXFUNCADDR5
4RXFUNCADDR4
3RXFUNCADDR3
2RXFUNCADDR2
1RXFUNCADDR1
0RXFUNCADDR0
1 field
Field
Bits
What it does
RXFUNCADDR
6:0
address of the target function
TXFUNADDR7.RXHUBADDREPRelevant In Host Mode Only. HUB Address
Address
0x460010BE
Reset
0x00
Access
read/write
7MULTRANS
6RXHUBADDR6
5RXHUBADDR5
4RXHUBADDR4
3RXHUBADDR3
2RXHUBADDR2
1RXHUBADDR1
0RXHUBADDR0
2 fields
Field
Bits
What it does
MULTRANS
7
hub has multiple or single translator
RXHUBADDR
6:0
hub address
TXFUNADDR7.RXHUBPORTRelevant In Host Mode Only. HUB Address
Address
0x460010BF
Reset
0x00
Access
read/write
7–
6HUBPORT6
5HUBPORT5
4HUBPORT4
3HUBPORT3
2HUBPORT2
1HUBPORT1
0HUBPORT0
1 field
Field
Bits
What it does
HUBPORT
6:0
Hub Port
DMAINTRDMA Interrupt Status for Each Channel
Address
0x46001200
Reset
0x00000000
Access
read/write
Size
32-bit
1 field
Field
Bits
What it does
DMAINTR
7:0
DMA Interrupt for each channel
DMACNT0.DMACNTLDMA Transfer Control For Each Channel
Address
0x46001204
Reset
0x00000000
Access
read/write
Size
32-bit
7 fields
Field
Bits
What it does
DMABRSTM
10:9
burst mode
0 Burst Mode 0
1 Burst Mode 1
2 Burst Mode 2
3 Burst Mode 3
DMAERR
8
bus error bit
DMAEP
7:4
endpoint number this channel is assigned to
DMAIE
3
interrupt enable
DMAMODE
2
transfer mode
0 Mode 0 Transfer
1 Mode1 Transfer
DMADIR
1
transfer direction
0 DMA Write (RX Endpoint)
1 DMA Read (TX Endpoint)
DMAEN
0
dma transfer enable
DMACNT0.DMAADDRMemory Address Of The Corresponding DMA Channel
Address
0x46001208
Reset
0x00000000
Access
read/write
Size
32-bit
2 fields
Field
Bits
What it does
ADDR10
1:0
Lower 2 bits of DMA memory address
ADDR312
31:2
upper 30 bits of address
DMACNT0.DMACOUNTCurrent DMA Count Of The Transfer
Address
0x4600120C
Reset
0x00000000
Access
read/write
Size
32-bit
1 field
Field
Bits
What it does
DMACOUNT
31:0
current dma count of the transfer
DMACNT1.DMACNTLDMA Transfer Control For Each Channel
Address
0x46001214
Reset
0x00000000
Access
read/write
Size
32-bit
7 fields
Field
Bits
What it does
DMABRSTM
10:9
burst mode
0 Burst Mode 0
1 Burst Mode 1
2 Burst Mode 2
3 Burst Mode 3
DMAERR
8
bus error bit
DMAEP
7:4
endpoint number this channel is assigned to
DMAIE
3
interrupt enable
DMAMODE
2
transfer mode
0 Mode 0 Transfer
1 Mode1 Transfer
DMADIR
1
transfer direction
0 DMA Write (RX Endpoint)
1 DMA Read (TX Endpoint)
DMAEN
0
dma transfer enable
DMACNT1.DMAADDRMemory Address Of The Corresponding DMA Channel
Address
0x46001218
Reset
0x00000000
Access
read/write
Size
32-bit
2 fields
Field
Bits
What it does
ADDR10
1:0
Lower 2 bits of DMA memory address
ADDR312
31:2
upper 30 bits of address
DMACNT1.DMACOUNTCurrent DMA Count Of The Transfer
Address
0x4600121C
Reset
0x00000000
Access
read/write
Size
32-bit
1 field
Field
Bits
What it does
DMACOUNT
31:0
current dma count of the transfer
DMACNT2.DMACNTLDMA Transfer Control For Each Channel
Address
0x46001224
Reset
0x00000000
Access
read/write
Size
32-bit
7 fields
Field
Bits
What it does
DMABRSTM
10:9
burst mode
0 Burst Mode 0
1 Burst Mode 1
2 Burst Mode 2
3 Burst Mode 3
DMAERR
8
bus error bit
DMAEP
7:4
endpoint number this channel is assigned to
DMAIE
3
interrupt enable
DMAMODE
2
transfer mode
0 Mode 0 Transfer
1 Mode1 Transfer
DMADIR
1
transfer direction
0 DMA Write (RX Endpoint)
1 DMA Read (TX Endpoint)
DMAEN
0
dma transfer enable
DMACNT2.DMAADDRMemory Address Of The Corresponding DMA Channel
Address
0x46001228
Reset
0x00000000
Access
read/write
Size
32-bit
2 fields
Field
Bits
What it does
ADDR10
1:0
Lower 2 bits of DMA memory address
ADDR312
31:2
upper 30 bits of address
DMACNT2.DMACOUNTCurrent DMA Count Of The Transfer
Address
0x4600122C
Reset
0x00000000
Access
read/write
Size
32-bit
1 field
Field
Bits
What it does
DMACOUNT
31:0
current dma count of the transfer
DMACNT3.DMACNTLDMA Transfer Control For Each Channel
Address
0x46001234
Reset
0x00000000
Access
read/write
Size
32-bit
7 fields
Field
Bits
What it does
DMABRSTM
10:9
burst mode
0 Burst Mode 0
1 Burst Mode 1
2 Burst Mode 2
3 Burst Mode 3
DMAERR
8
bus error bit
DMAEP
7:4
endpoint number this channel is assigned to
DMAIE
3
interrupt enable
DMAMODE
2
transfer mode
0 Mode 0 Transfer
1 Mode1 Transfer
DMADIR
1
transfer direction
0 DMA Write (RX Endpoint)
1 DMA Read (TX Endpoint)
DMAEN
0
dma transfer enable
DMACNT3.DMAADDRMemory Address Of The Corresponding DMA Channel
Address
0x46001238
Reset
0x00000000
Access
read/write
Size
32-bit
2 fields
Field
Bits
What it does
ADDR10
1:0
Lower 2 bits of DMA memory address
ADDR312
31:2
upper 30 bits of address
DMACNT3.DMACOUNTCurrent DMA Count Of The Transfer
Address
0x4600123C
Reset
0x00000000
Access
read/write
Size
32-bit
1 field
Field
Bits
What it does
DMACOUNT
31:0
current dma count of the transfer
DMACNT4.DMACNTLDMA Transfer Control For Each Channel
Address
0x46001244
Reset
0x00000000
Access
read/write
Size
32-bit
7 fields
Field
Bits
What it does
DMABRSTM
10:9
burst mode
0 Burst Mode 0
1 Burst Mode 1
2 Burst Mode 2
3 Burst Mode 3
DMAERR
8
bus error bit
DMAEP
7:4
endpoint number this channel is assigned to
DMAIE
3
interrupt enable
DMAMODE
2
transfer mode
0 Mode 0 Transfer
1 Mode1 Transfer
DMADIR
1
transfer direction
0 DMA Write (RX Endpoint)
1 DMA Read (TX Endpoint)
DMAEN
0
dma transfer enable
DMACNT4.DMAADDRMemory Address Of The Corresponding DMA Channel
Address
0x46001248
Reset
0x00000000
Access
read/write
Size
32-bit
2 fields
Field
Bits
What it does
ADDR10
1:0
Lower 2 bits of DMA memory address
ADDR312
31:2
upper 30 bits of address
DMACNT4.DMACOUNTCurrent DMA Count Of The Transfer
Address
0x4600124C
Reset
0x00000000
Access
read/write
Size
32-bit
1 field
Field
Bits
What it does
DMACOUNT
31:0
current dma count of the transfer
DMACNT5.DMACNTLDMA Transfer Control For Each Channel
Address
0x46001254
Reset
0x00000000
Access
read/write
Size
32-bit
7 fields
Field
Bits
What it does
DMABRSTM
10:9
burst mode
0 Burst Mode 0
1 Burst Mode 1
2 Burst Mode 2
3 Burst Mode 3
DMAERR
8
bus error bit
DMAEP
7:4
endpoint number this channel is assigned to
DMAIE
3
interrupt enable
DMAMODE
2
transfer mode
0 Mode 0 Transfer
1 Mode1 Transfer
DMADIR
1
transfer direction
0 DMA Write (RX Endpoint)
1 DMA Read (TX Endpoint)
DMAEN
0
dma transfer enable
DMACNT5.DMAADDRMemory Address Of The Corresponding DMA Channel
Address
0x46001258
Reset
0x00000000
Access
read/write
Size
32-bit
2 fields
Field
Bits
What it does
ADDR10
1:0
Lower 2 bits of DMA memory address
ADDR312
31:2
upper 30 bits of address
DMACNT5.DMACOUNTCurrent DMA Count Of The Transfer
Address
0x4600125C
Reset
0x00000000
Access
read/write
Size
32-bit
1 field
Field
Bits
What it does
DMACOUNT
31:0
current dma count of the transfer
DMACNT6.DMACNTLDMA Transfer Control For Each Channel
Address
0x46001264
Reset
0x00000000
Access
read/write
Size
32-bit
7 fields
Field
Bits
What it does
DMABRSTM
10:9
burst mode
0 Burst Mode 0
1 Burst Mode 1
2 Burst Mode 2
3 Burst Mode 3
DMAERR
8
bus error bit
DMAEP
7:4
endpoint number this channel is assigned to
DMAIE
3
interrupt enable
DMAMODE
2
transfer mode
0 Mode 0 Transfer
1 Mode1 Transfer
DMADIR
1
transfer direction
0 DMA Write (RX Endpoint)
1 DMA Read (TX Endpoint)
DMAEN
0
dma transfer enable
DMACNT6.DMAADDRMemory Address Of The Corresponding DMA Channel
Address
0x46001268
Reset
0x00000000
Access
read/write
Size
32-bit
2 fields
Field
Bits
What it does
ADDR10
1:0
Lower 2 bits of DMA memory address
ADDR312
31:2
upper 30 bits of address
DMACNT6.DMACOUNTCurrent DMA Count Of The Transfer
Address
0x4600126C
Reset
0x00000000
Access
read/write
Size
32-bit
1 field
Field
Bits
What it does
DMACOUNT
31:0
current dma count of the transfer
DMACNT7.DMACNTLDMA Transfer Control For Each Channel
Address
0x46001274
Reset
0x00000000
Access
read/write
Size
32-bit
7 fields
Field
Bits
What it does
DMABRSTM
10:9
burst mode
0 Burst Mode 0
1 Burst Mode 1
2 Burst Mode 2
3 Burst Mode 3
DMAERR
8
bus error bit
DMAEP
7:4
endpoint number this channel is assigned to
DMAIE
3
interrupt enable
DMAMODE
2
transfer mode
0 Mode 0 Transfer
1 Mode1 Transfer
DMADIR
1
transfer direction
0 DMA Write (RX Endpoint)
1 DMA Read (TX Endpoint)
DMAEN
0
dma transfer enable
DMACNT7.DMAADDRMemory Address Of The Corresponding DMA Channel
Address
0x46001278
Reset
0x00000000
Access
read/write
Size
32-bit
2 fields
Field
Bits
What it does
ADDR10
1:0
Lower 2 bits of DMA memory address
ADDR312
31:2
upper 30 bits of address
DMACNT7.DMACOUNTCurrent DMA Count Of The Transfer
Address
0x4600127C
Reset
0x00000000
Access
read/write
Size
32-bit
1 field
Field
Bits
What it does
DMACOUNT
31:0
current dma count of the transfer
RQPKTCOUNT0Host Mode Only: Used To Specify Number Of Packets That Are To Be Transaferred In A Block Transfer
Address
0x46001304
Reset
0x00000000
Access
read/write
Size
32-bit
1 field
Field
Bits
What it does
RQPKTCOUNT
15:0
sets the number of packets of size maxp that are to be transferred in a block transfer. only used in host mode when autoreq is set. has no effect in peripheral mode or when autoreq is not set.
RQPKTCOUNT1Host Mode Only: Used To Specify Number Of Packets That Are To Be Transaferred In A Block Transfer
Address
0x46001308
Reset
0x00000000
Access
read/write
Size
32-bit
1 field
Field
Bits
What it does
RQPKTCOUNT
15:0
sets the number of packets of size maxp that are to be transferred in a block transfer. only used in host mode when autoreq is set. has no effect in peripheral mode or when autoreq is not set.
RQPKTCOUNT2Host Mode Only: Used To Specify Number Of Packets That Are To Be Transaferred In A Block Transfer
Address
0x4600130C
Reset
0x00000000
Access
read/write
Size
32-bit
1 field
Field
Bits
What it does
RQPKTCOUNT
15:0
sets the number of packets of size maxp that are to be transferred in a block transfer. only used in host mode when autoreq is set. has no effect in peripheral mode or when autoreq is not set.
RQPKTCOUNT3Host Mode Only: Used To Specify Number Of Packets That Are To Be Transaferred In A Block Transfer
Address
0x46001310
Reset
0x00000000
Access
read/write
Size
32-bit
1 field
Field
Bits
What it does
RQPKTCOUNT
15:0
sets the number of packets of size maxp that are to be transferred in a block transfer. only used in host mode when autoreq is set. has no effect in peripheral mode or when autoreq is not set.
RQPKTCOUNT4Host Mode Only: Used To Specify Number Of Packets That Are To Be Transaferred In A Block Transfer
Address
0x46001314
Reset
0x00000000
Access
read/write
Size
32-bit
1 field
Field
Bits
What it does
RQPKTCOUNT
15:0
sets the number of packets of size maxp that are to be transferred in a block transfer. only used in host mode when autoreq is set. has no effect in peripheral mode or when autoreq is not set.
RQPKTCOUNT5Host Mode Only: Used To Specify Number Of Packets That Are To Be Transaferred In A Block Transfer
Address
0x46001318
Reset
0x00000000
Access
read/write
Size
32-bit
1 field
Field
Bits
What it does
RQPKTCOUNT
15:0
sets the number of packets of size maxp that are to be transferred in a block transfer. only used in host mode when autoreq is set. has no effect in peripheral mode or when autoreq is not set.
RQPKTCOUNT6Host Mode Only: Used To Specify Number Of Packets That Are To Be Transaferred In A Block Transfer
Address
0x4600131C
Reset
0x00000000
Access
read/write
Size
32-bit
1 field
Field
Bits
What it does
RQPKTCOUNT
15:0
sets the number of packets of size maxp that are to be transferred in a block transfer. only used in host mode when autoreq is set. has no effect in peripheral mode or when autoreq is not set.
RXDPKTBUFDISIndicates Which Of The RX Endpoints Have Disabled Double Packet Buffer Functionality
Address
0x46001340
Reset
0x0000
Access
read/write
Size
16-bit
1 field
Field
Bits
What it does
EPxRXDIS
15:1
each bit indicates which of the Rx endpoint have disabled double buffer functionality
TXDPKTBUFDISIndicates Which Of The TX Endpoints Have Disabled Double Packet Buffer Functionality
Address
0x46001342
Reset
0x0000
Access
read/write
Size
16-bit
1 field
Field
Bits
What it does
EPxTXDIS
15:1
each bit indicates which of the Tx endpoint have disabled double buffer functionality
CTUCHChirp Timeout. Number Of XCLK Cycles Before The Timeout
Address
0x46001344
Reset
0x4074
Access
read/write
Size
16-bit
1 field
Field
Bits
What it does
CTUCH
15:0
this number when multiplied by 4 represents the number of xclk cycles before the timeout occurs
CTHHSRTNSets The Delay From The End Of High-Speed Resume Signaling (Acting As A Host) To Enable The UTM Normal Operating Mode
Address
0x46001346
Reset
0x0032
Access
read/write
Size
16-bit
1 field
Field
Bits
What it does
CTHHSRTN
15:0
the delay from the end of high speed resume signaling to enabling utm normal operating mode.
CTHSBTThis Register Represents The Value To Be Added To The Minimum High Speed Timeout Period Of 736 Bit Times.
Address
0x46001348
Reset
0x0000
Access
read/write
Size
16-bit
1 field
Field
Bits
What it does
HSTMEOUTADD
3:0
this register represents the value to be added to the mimumum high speed timeout period of 736 bit times
LPMATTRDefines The Attributes Of An LPM Transaction And Sleep Cycle.
Address
0x46001360
Reset
0x0000
Access
read/write
Size
16-bit
4 fields
Field
Bits
What it does
ENDPOINT
15:12
this is the endpnt that in the token packet of the lpm transaction.
RMTWAK
8
this bit is the remote wakeup enable bit.
HIRD
7:4
this is the host initiated resume duration.
LINKSTATE
3:0
this value is provided by the host to the peripheral to indicate what state the peripheral must transition to after the receipt and acceptance of a lpm transaction.
1 Sleep State (L1)
LPMCNTRLLPM Control Register
Address
0x46001362
Reset
0x00
Access
read/write
7–
6–
5–
4LPMNAK
3LPMEN1
2LPMEN0
1LPMRES
0LPMXMT
6 fields
Field
Bits
What it does
LPMNAK
4
this bit is used to place all end points in a state such that the response to all transactions other then an lpm transaction will be a nak.
LPMEN
3:2
this register is used to enable lpm in the musbmhdrc.
0 Core supports LPM extended transactions
1 LPM is not supported but extended transactions are supported.
2 LPM and extended transactions are not supported
3 LPM and extended transactions are not supported
LPMRES
1
this bit is used by software to initiate a resume from the l1 state
LPMRES
1
this bit is used by software to initiate resume (remote wakeup).
LPMXMT
0
software should set this bit to transmit an lpm transaction.
LPMXMT
0
this bit is set by software to instruct the core to transition to the l1 state upon the receipt of the next lpm transaction.
LPMINTRENLPM Interrupts Enable Register
Address
0x46001363
Reset
0x00
Access
read/write
7–
6–
5LPMERREN
4LPMRESEN
3LPMNCEN
2LPMACKEN
1LPMNYEN
0LPMSTEN
6 fields
Field
Bits
What it does
LPMERREN
5
LPMERR interrupt
LPMRESEN
4
LPMRES interrupt
LPMNCEN
3
LPMNC interrupt
LPMACKEN
2
LPMACK interrupt
LPMNYEN
1
LPMMNY interrupt
LPMSTEN
0
LPMMST interrupt
LPMINTRStatus Of The LPM Power State
Address
0x46001364
Reset
0x00
Access
read/write
7–
6–
5LPMERR
4LPMRES
3LPMNC
2LPMACK
1LPMNY
0LPMST
12 fields
Field
Bits
What it does
LPMERR
5
this bit is set if a response to the lpm transaction is received with a bit stuff error or a pid error
LPMERR
5
this bit is set if an lpm transaction is received that has a linkstate field that is not supported
LPMRES
4
this bit is set if the core has been resumed for any reason.
LPMRES
4
this bit is set when the core has been resumed for any reason.
LPMNC
3
this bit is set when an lpm transaction has been transmitted and has failed to complete.
LPMNC
3
this bit is set when an lpm transaction is received and the core responds with a nyet due to data pending in the rx fifos.
LPMACK
2
this bit is set when an lpm transaction is received and the core responds with an ack.
LPMACK
2
this bit is set when an lpm transaction is transmitted and the device responds with an ack.
LPMNY
1
this bit is set when an lpm transaction is received and the core responds with a nyet
LPMNY
1
this bit is set when an lpm transaction is transmitted and the device responds with a nyet.
LPMST
0
this bit is set when an lpm transaction is received and the core responds with a stall.
LPMST
0
this bit is set when an lpm transaction is transmitted and the device responds with a stall.
LPMFADDRFunction Address In LPM Payload
Address
0x46001365
Reset
0x00
Access
read/write
7–
6FUNCADDR6
5FUNCADDR5
4FUNCADDR4
3FUNCADDR3
2FUNCADDR2
1FUNCADDR1
0FUNCADDR0
1 field
Field
Bits
What it does
FUNCADDR
6:0
function address that will be placed in the LPM payload
PHY00USBHPHY Control Register.
Address
0x46001500
Reset
0x00000019
Access
read/write
Size
32-bit
3 fields
Field
Bits
What it does
RXPHSSEL
7:5
RX clock phase select
0 Earliest phase
7 Latest phase
SLEWRATE
4:3
adjust FS/LS slew rate
0 Highest slew rate
1 Middle slew rate
2 Middle slew rate
3 Smallest slew rate
PREEMP
2:0
enables pre-emphasis
0 Enable pre-emphasis during SOF and EOP
1 Enable pre-emphasis during chirp
2 Enable pre-emphasis in non-chirp state
3 Always enable pre-emphasis
PHY04USBHPHY Control Register.
Address
0x46001504
Reset
0x0000008F
Access
read/write
Size
32-bit
4 fields
Field
Bits
What it does
SQUELCH210
7:5
Lower 3 bits of RX squelch trigger point configuration
HIZ
4
Set D+/D- to a high impedence state
RSVD
3
Reserved
TXPHSSEL
1:0
set the Tx clock phase select
PHY08USBHPHY Control Register.
Address
0x46001508
Reset
0x00000007
Access
read/write
Size
32-bit
2 fields
Field
Bits
What it does
RSVD
7:1
Reserved
SQUELCH3
0
MSB of Squelch configuration
PHY0CUSBHPHY Control Register.
Address
0x4600150C
Reset
0x000000E0
Access
read/write
Size
32-bit
1 field
Field
Bits
What it does
TUNE210
11:5
Lower 3 bits for HS amplitude tuning
PHY10USBHPHY Control Register.
Address
0x46001510
Reset
0x000000AA
Access
read/write
Size
32-bit
2 fields
Field
Bits
What it does
DRVTUNE210
7:5
Lower 3 bits for HS/FS/LS driver strength tuning
TUNE76543
4:0
Upper 5 bits for HS amplitude tuning
PHY14USBHPHY Control Register.
Address
0x46001514
Reset
0x00000012
Access
read/write
Size
32-bit
4 fields
Field
Bits
What it does
ODT0
7
On die termination compensation voltage reference
BYPSSSQUELCH
4
Bypass squelch trigger point configure in chirp mode
COMPBYPSS
3:2
Auto compensation bypass
DRVTUNE43
1:0
Upper 2 bits for HS/FS/LS driver strength tuning
PHY18USBHPHY Control Register.
Address
0x46001518
Reset
0x00000008
Access
read/write
Size
32-bit
2 fields
Field
Bits
What it does
RSVD
5:2
reserved
ODT21
1:0
Upper 3 bits for on die termination compensation voltage reference
PHY1CUSBHPHY Control Register.
Address
0x4600151C
Reset
0x00000082
Access
read/write
Size
32-bit
2 fields
Field
Bits
What it does
FSLSDIFF
7
Turn off FS/LS differential receiver in suspend mode
BETA