PIC32CZ2051CA90144 EVSYS registers

The 284 registers of EVSYS (Event System Interface), from 0x44860000, with their reset value and every field. The PIC32CZ2051CA90144 has 5988 registers in 67 peripherals, one page each.

EVSYS Event System Interface

CTRLAControl

Address
0x44860000
Reset
0x00
Access
write only
  1. 7–
  2. 6–
  3. 5–
  4. 4–
  5. 3–
  6. 2–
  7. 1–
  8. 0SWRST
1 field
FieldBitsWhat it does
SWRST0Software Reset

SWEVTSoftware Event

Address
0x44860004
Reset
0x00000000
Access
write only
Size
32-bit
32 fields
FieldBitsWhat it does
CHANNEL3030Channel 30 Software Selection
CHANNEL2929Channel 29 Software Selection
CHANNEL2828Channel 28 Software Selection
CHANNEL2727Channel 27 Software Selection
CHANNEL2626Channel 26 Software Selection
CHANNEL2525Channel 25 Software Selection
CHANNEL2424Channel 24 Software Selection
CHANNEL2323Channel 23 Software Selection
CHANNEL2222Channel 22 Software Selection
CHANNEL2121Channel 21 Software Selection
CHANNEL2020Channel 20 Software Selection
CHANNEL1919Channel 19 Software Selection
CHANNEL1818Channel 18 Software Selection
CHANNEL1717Channel 17 Software Selection
CHANNEL1616Channel 16 Software Selection
CHANNEL1515Channel 15 Software Selection
CHANNEL1414Channel 14 Software Selection
CHANNEL1313Channel 13 Software Selection
CHANNEL1212Channel 12 Software Selection
CHANNEL1111Channel 11 Software Selection
CHANNEL1010Channel 10 Software Selection
CHANNEL99Channel 9 Software Selection
CHANNEL88Channel 8 Software Selection
CHANNEL77Channel 7 Software Selection
CHANNEL66Channel 6 Software Selection
CHANNEL55Channel 5 Software Selection
CHANNEL44Channel 4 Software Selection
CHANNEL33Channel 3 Software Selection
CHANNEL22Channel 2 Software Selection
CHANNEL11Channel 1 Software Selection
CHANNEL00Channel 0 Software Selection
CHANNEL3131Channel 31 Software Selection

PRICTRLPriority Control

Address
0x44860008
Reset
0x00
Access
read/write
  1. 7RREN
  2. 6–
  3. 5–
  4. 4–
  5. 3PRI3
  6. 2PRI2
  7. 1PRI1
  8. 0PRI0
2 fields
FieldBitsWhat it does
RREN7Round-Robin Scheduling Enable
PRI3:0Channel Priority Number

INTPENDChannel Pending Interrupt

Address
0x44860010
Reset
0x4000
Access
read/write
Size
16-bit
5 fields
FieldBitsWhat it does
BUSY15Busy
READY14Ready
EVD9Channel Event Detected
OVR8Channel Overrun
ID3:0Channel ID

INTSTATUSInterrupt Status

Address
0x44860014
Reset
0x00000000
Access
read only
Size
32-bit
12 fields
FieldBitsWhat it does
CHINT1111Channel 11 Pending Interrupt
CHINT1010Channel 10 Pending Interrupt
CHINT99Channel 9 Pending Interrupt
CHINT88Channel 8 Pending Interrupt
CHINT77Channel 7 Pending Interrupt
CHINT66Channel 6 Pending Interrupt
CHINT55Channel 5 Pending Interrupt
CHINT44Channel 4 Pending Interrupt
CHINT33Channel 3 Pending Interrupt
CHINT22Channel 2 Pending Interrupt
CHINT11Channel 1 Pending Interrupt
CHINT00Channel 0 Pending Interrupt

BUSYCHBusy Channels

Address
0x44860018
Reset
0x00000000
Access
read only
Size
32-bit
12 fields
FieldBitsWhat it does
BUSYCH1111Busy Channel 11
BUSYCH1010Busy Channel 10
BUSYCH99Busy Channel 9
BUSYCH88Busy Channel 8
BUSYCH77Busy Channel 7
BUSYCH66Busy Channel 6
BUSYCH55Busy Channel 5
BUSYCH44Busy Channel 4
BUSYCH33Busy Channel 3
BUSYCH22Busy Channel 2
BUSYCH11Busy Channel 1
BUSYCH00Busy Channel 0

READYUSRReady Users

Address
0x4486001C
Reset
0xFFFFFFFF
Access
read only
Size
32-bit
12 fields
FieldBitsWhat it does
READYUSR1111Ready User for Channel 11
READYUSR1010Ready User for Channel 10
READYUSR99Ready User for Channel 9
READYUSR88Ready User for Channel 8
READYUSR77Ready User for Channel 7
READYUSR66Ready User for Channel 6
READYUSR55Ready User for Channel 5
READYUSR44Ready User for Channel 4
READYUSR33Ready User for Channel 3
READYUSR22Ready User for Channel 2
READYUSR11Ready User for Channel 1
READYUSR00Ready User for Channel 0

CHANNEL0.CHANNELChannel n Control

Address
0x44860020
Reset
0x00008000
Access
read/write
Size
32-bit
5 fields
FieldBitsWhat it does
ONDEMAND15Generic Clock On Demand
RUNSTDBY14Run in standby
EDGSEL11:10Edge Detection Selection
  • 0 No event output when using the resynchronized or synchronous path
  • 1 Event detection only on the rising edge of the signal from the event generator when using the resynchronized or synchronous path
  • 2 Event detection only on the falling edge of the signal from the event generator when using the resynchronized or synchronous path
  • 3 Event detection on rising and falling edges of the signal from the event generator when using the resynchronized or synchronous path
PATH9:8Path Selection
  • 0 Asynchronous path
  • 1 Resynchronized path
EVGEN7:0Event Generator Selection

CHANNEL0.CHINTENCLRChannel n Interrupt Enable Clear

Address
0x44860024
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5–
  4. 4–
  5. 3–
  6. 2–
  7. 1EVD
  8. 0OVR
2 fields
FieldBitsWhat it does
EVD1Channel Event Detected Interrupt Disable
OVR0Channel Overrun Interrupt Disable

CHANNEL0.CHINTENSETChannel n Interrupt Enable Set

Address
0x44860025
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5–
  4. 4–
  5. 3–
  6. 2–
  7. 1EVD
  8. 0OVR
2 fields
FieldBitsWhat it does
EVD1Channel Event Detected Interrupt Enable
OVR0Channel Overrun Interrupt Enable

CHANNEL0.CHINTFLAGChannel n Interrupt Flag Status and Clear

Address
0x44860026
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5–
  4. 4–
  5. 3–
  6. 2–
  7. 1EVD
  8. 0OVR
2 fields
FieldBitsWhat it does
EVD1Channel Event Detected
OVR0Channel Overrun

CHANNEL0.CHSTATUSChannel n Status

Address
0x44860027
Reset
0x01
Access
read only
  1. 7–
  2. 6–
  3. 5–
  4. 4–
  5. 3–
  6. 2–
  7. 1BUSYCH
  8. 0RDYUSR
2 fields
FieldBitsWhat it does
BUSYCH1Busy Channel
RDYUSR0Ready User

CHANNEL1.CHANNELChannel n Control

Address
0x44860028
Reset
0x00008000
Access
read/write
Size
32-bit
5 fields
FieldBitsWhat it does
ONDEMAND15Generic Clock On Demand
RUNSTDBY14Run in standby
EDGSEL11:10Edge Detection Selection
  • 0 No event output when using the resynchronized or synchronous path
  • 1 Event detection only on the rising edge of the signal from the event generator when using the resynchronized or synchronous path
  • 2 Event detection only on the falling edge of the signal from the event generator when using the resynchronized or synchronous path
  • 3 Event detection on rising and falling edges of the signal from the event generator when using the resynchronized or synchronous path
PATH9:8Path Selection
  • 0 Asynchronous path
  • 1 Resynchronized path
EVGEN7:0Event Generator Selection

CHANNEL1.CHINTENCLRChannel n Interrupt Enable Clear

Address
0x4486002C
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5–
  4. 4–
  5. 3–
  6. 2–
  7. 1EVD
  8. 0OVR
2 fields
FieldBitsWhat it does
EVD1Channel Event Detected Interrupt Disable
OVR0Channel Overrun Interrupt Disable

CHANNEL1.CHINTENSETChannel n Interrupt Enable Set

Address
0x4486002D
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5–
  4. 4–
  5. 3–
  6. 2–
  7. 1EVD
  8. 0OVR
2 fields
FieldBitsWhat it does
EVD1Channel Event Detected Interrupt Enable
OVR0Channel Overrun Interrupt Enable

CHANNEL1.CHINTFLAGChannel n Interrupt Flag Status and Clear

Address
0x4486002E
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5–
  4. 4–
  5. 3–
  6. 2–
  7. 1EVD
  8. 0OVR
2 fields
FieldBitsWhat it does
EVD1Channel Event Detected
OVR0Channel Overrun

CHANNEL1.CHSTATUSChannel n Status

Address
0x4486002F
Reset
0x01
Access
read only
  1. 7–
  2. 6–
  3. 5–
  4. 4–
  5. 3–
  6. 2–
  7. 1BUSYCH
  8. 0RDYUSR
2 fields
FieldBitsWhat it does
BUSYCH1Busy Channel
RDYUSR0Ready User

CHANNEL2.CHANNELChannel n Control

Address
0x44860030
Reset
0x00008000
Access
read/write
Size
32-bit
5 fields
FieldBitsWhat it does
ONDEMAND15Generic Clock On Demand
RUNSTDBY14Run in standby
EDGSEL11:10Edge Detection Selection
  • 0 No event output when using the resynchronized or synchronous path
  • 1 Event detection only on the rising edge of the signal from the event generator when using the resynchronized or synchronous path
  • 2 Event detection only on the falling edge of the signal from the event generator when using the resynchronized or synchronous path
  • 3 Event detection on rising and falling edges of the signal from the event generator when using the resynchronized or synchronous path
PATH9:8Path Selection
  • 0 Asynchronous path
  • 1 Resynchronized path
EVGEN7:0Event Generator Selection

CHANNEL2.CHINTENCLRChannel n Interrupt Enable Clear

Address
0x44860034
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5–
  4. 4–
  5. 3–
  6. 2–
  7. 1EVD
  8. 0OVR
2 fields
FieldBitsWhat it does
EVD1Channel Event Detected Interrupt Disable
OVR0Channel Overrun Interrupt Disable

CHANNEL2.CHINTENSETChannel n Interrupt Enable Set

Address
0x44860035
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5–
  4. 4–
  5. 3–
  6. 2–
  7. 1EVD
  8. 0OVR
2 fields
FieldBitsWhat it does
EVD1Channel Event Detected Interrupt Enable
OVR0Channel Overrun Interrupt Enable

CHANNEL2.CHINTFLAGChannel n Interrupt Flag Status and Clear

Address
0x44860036
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5–
  4. 4–
  5. 3–
  6. 2–
  7. 1EVD
  8. 0OVR
2 fields
FieldBitsWhat it does
EVD1Channel Event Detected
OVR0Channel Overrun

CHANNEL2.CHSTATUSChannel n Status

Address
0x44860037
Reset
0x01
Access
read only
  1. 7–
  2. 6–
  3. 5–
  4. 4–
  5. 3–
  6. 2–
  7. 1BUSYCH
  8. 0RDYUSR
2 fields
FieldBitsWhat it does
BUSYCH1Busy Channel
RDYUSR0Ready User

CHANNEL3.CHANNELChannel n Control

Address
0x44860038
Reset
0x00008000
Access
read/write
Size
32-bit
5 fields
FieldBitsWhat it does
ONDEMAND15Generic Clock On Demand
RUNSTDBY14Run in standby
EDGSEL11:10Edge Detection Selection
  • 0 No event output when using the resynchronized or synchronous path
  • 1 Event detection only on the rising edge of the signal from the event generator when using the resynchronized or synchronous path
  • 2 Event detection only on the falling edge of the signal from the event generator when using the resynchronized or synchronous path
  • 3 Event detection on rising and falling edges of the signal from the event generator when using the resynchronized or synchronous path
PATH9:8Path Selection
  • 0 Asynchronous path
  • 1 Resynchronized path
EVGEN7:0Event Generator Selection

CHANNEL3.CHINTENCLRChannel n Interrupt Enable Clear

Address
0x4486003C
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5–
  4. 4–
  5. 3–
  6. 2–
  7. 1EVD
  8. 0OVR
2 fields
FieldBitsWhat it does
EVD1Channel Event Detected Interrupt Disable
OVR0Channel Overrun Interrupt Disable

CHANNEL3.CHINTENSETChannel n Interrupt Enable Set

Address
0x4486003D
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5–
  4. 4–
  5. 3–
  6. 2–
  7. 1EVD
  8. 0OVR
2 fields
FieldBitsWhat it does
EVD1Channel Event Detected Interrupt Enable
OVR0Channel Overrun Interrupt Enable

CHANNEL3.CHINTFLAGChannel n Interrupt Flag Status and Clear

Address
0x4486003E
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5–
  4. 4–
  5. 3–
  6. 2–
  7. 1EVD
  8. 0OVR
2 fields
FieldBitsWhat it does
EVD1Channel Event Detected
OVR0Channel Overrun

CHANNEL3.CHSTATUSChannel n Status

Address
0x4486003F
Reset
0x01
Access
read only
  1. 7–
  2. 6–
  3. 5–
  4. 4–
  5. 3–
  6. 2–
  7. 1BUSYCH
  8. 0RDYUSR
2 fields
FieldBitsWhat it does
BUSYCH1Busy Channel
RDYUSR0Ready User

CHANNEL4.CHANNELChannel n Control

Address
0x44860040
Reset
0x00008000
Access
read/write
Size
32-bit
5 fields
FieldBitsWhat it does
ONDEMAND15Generic Clock On Demand
RUNSTDBY14Run in standby
EDGSEL11:10Edge Detection Selection
  • 0 No event output when using the resynchronized or synchronous path
  • 1 Event detection only on the rising edge of the signal from the event generator when using the resynchronized or synchronous path
  • 2 Event detection only on the falling edge of the signal from the event generator when using the resynchronized or synchronous path
  • 3 Event detection on rising and falling edges of the signal from the event generator when using the resynchronized or synchronous path
PATH9:8Path Selection
  • 0 Asynchronous path
  • 1 Resynchronized path
EVGEN7:0Event Generator Selection

CHANNEL4.CHINTENCLRChannel n Interrupt Enable Clear

Address
0x44860044
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5–
  4. 4–
  5. 3–
  6. 2–
  7. 1EVD
  8. 0OVR
2 fields
FieldBitsWhat it does
EVD1Channel Event Detected Interrupt Disable
OVR0Channel Overrun Interrupt Disable

CHANNEL4.CHINTENSETChannel n Interrupt Enable Set

Address
0x44860045
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5–
  4. 4–
  5. 3–
  6. 2–
  7. 1EVD
  8. 0OVR
2 fields
FieldBitsWhat it does
EVD1Channel Event Detected Interrupt Enable
OVR0Channel Overrun Interrupt Enable

CHANNEL4.CHINTFLAGChannel n Interrupt Flag Status and Clear

Address
0x44860046
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5–
  4. 4–
  5. 3–
  6. 2–
  7. 1EVD
  8. 0OVR
2 fields
FieldBitsWhat it does
EVD1Channel Event Detected
OVR0Channel Overrun

CHANNEL4.CHSTATUSChannel n Status

Address
0x44860047
Reset
0x01
Access
read only
  1. 7–
  2. 6–
  3. 5–
  4. 4–
  5. 3–
  6. 2–
  7. 1BUSYCH
  8. 0RDYUSR
2 fields
FieldBitsWhat it does
BUSYCH1Busy Channel
RDYUSR0Ready User

CHANNEL5.CHANNELChannel n Control

Address
0x44860048
Reset
0x00008000
Access
read/write
Size
32-bit
5 fields
FieldBitsWhat it does
ONDEMAND15Generic Clock On Demand
RUNSTDBY14Run in standby
EDGSEL11:10Edge Detection Selection
  • 0 No event output when using the resynchronized or synchronous path
  • 1 Event detection only on the rising edge of the signal from the event generator when using the resynchronized or synchronous path
  • 2 Event detection only on the falling edge of the signal from the event generator when using the resynchronized or synchronous path
  • 3 Event detection on rising and falling edges of the signal from the event generator when using the resynchronized or synchronous path
PATH9:8Path Selection
  • 0 Asynchronous path
  • 1 Resynchronized path
EVGEN7:0Event Generator Selection

CHANNEL5.CHINTENCLRChannel n Interrupt Enable Clear

Address
0x4486004C
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5–
  4. 4–
  5. 3–
  6. 2–
  7. 1EVD
  8. 0OVR
2 fields
FieldBitsWhat it does
EVD1Channel Event Detected Interrupt Disable
OVR0Channel Overrun Interrupt Disable

CHANNEL5.CHINTENSETChannel n Interrupt Enable Set

Address
0x4486004D
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5–
  4. 4–
  5. 3–
  6. 2–
  7. 1EVD
  8. 0OVR
2 fields
FieldBitsWhat it does
EVD1Channel Event Detected Interrupt Enable
OVR0Channel Overrun Interrupt Enable

CHANNEL5.CHINTFLAGChannel n Interrupt Flag Status and Clear

Address
0x4486004E
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5–
  4. 4–
  5. 3–
  6. 2–
  7. 1EVD
  8. 0OVR
2 fields
FieldBitsWhat it does
EVD1Channel Event Detected
OVR0Channel Overrun

CHANNEL5.CHSTATUSChannel n Status

Address
0x4486004F
Reset
0x01
Access
read only
  1. 7–
  2. 6–
  3. 5–
  4. 4–
  5. 3–
  6. 2–
  7. 1BUSYCH
  8. 0RDYUSR
2 fields
FieldBitsWhat it does
BUSYCH1Busy Channel
RDYUSR0Ready User

CHANNEL6.CHANNELChannel n Control

Address
0x44860050
Reset
0x00008000
Access
read/write
Size
32-bit
5 fields
FieldBitsWhat it does
ONDEMAND15Generic Clock On Demand
RUNSTDBY14Run in standby
EDGSEL11:10Edge Detection Selection
  • 0 No event output when using the resynchronized or synchronous path
  • 1 Event detection only on the rising edge of the signal from the event generator when using the resynchronized or synchronous path
  • 2 Event detection only on the falling edge of the signal from the event generator when using the resynchronized or synchronous path
  • 3 Event detection on rising and falling edges of the signal from the event generator when using the resynchronized or synchronous path
PATH9:8Path Selection
  • 0 Asynchronous path
  • 1 Resynchronized path
EVGEN7:0Event Generator Selection

CHANNEL6.CHINTENCLRChannel n Interrupt Enable Clear

Address
0x44860054
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5–
  4. 4–
  5. 3–
  6. 2–
  7. 1EVD
  8. 0OVR
2 fields
FieldBitsWhat it does
EVD1Channel Event Detected Interrupt Disable
OVR0Channel Overrun Interrupt Disable

CHANNEL6.CHINTENSETChannel n Interrupt Enable Set

Address
0x44860055
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5–
  4. 4–
  5. 3–
  6. 2–
  7. 1EVD
  8. 0OVR
2 fields
FieldBitsWhat it does
EVD1Channel Event Detected Interrupt Enable
OVR0Channel Overrun Interrupt Enable

CHANNEL6.CHINTFLAGChannel n Interrupt Flag Status and Clear

Address
0x44860056
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5–
  4. 4–
  5. 3–
  6. 2–
  7. 1EVD
  8. 0OVR
2 fields
FieldBitsWhat it does
EVD1Channel Event Detected
OVR0Channel Overrun

CHANNEL6.CHSTATUSChannel n Status

Address
0x44860057
Reset
0x01
Access
read only
  1. 7–
  2. 6–
  3. 5–
  4. 4–
  5. 3–
  6. 2–
  7. 1BUSYCH
  8. 0RDYUSR
2 fields
FieldBitsWhat it does
BUSYCH1Busy Channel
RDYUSR0Ready User

CHANNEL7.CHANNELChannel n Control

Address
0x44860058
Reset
0x00008000
Access
read/write
Size
32-bit
5 fields
FieldBitsWhat it does
ONDEMAND15Generic Clock On Demand
RUNSTDBY14Run in standby
EDGSEL11:10Edge Detection Selection
  • 0 No event output when using the resynchronized or synchronous path
  • 1 Event detection only on the rising edge of the signal from the event generator when using the resynchronized or synchronous path
  • 2 Event detection only on the falling edge of the signal from the event generator when using the resynchronized or synchronous path
  • 3 Event detection on rising and falling edges of the signal from the event generator when using the resynchronized or synchronous path
PATH9:8Path Selection
  • 0 Asynchronous path
  • 1 Resynchronized path
EVGEN7:0Event Generator Selection

CHANNEL7.CHINTENCLRChannel n Interrupt Enable Clear

Address
0x4486005C
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5–
  4. 4–
  5. 3–
  6. 2–
  7. 1EVD
  8. 0OVR
2 fields
FieldBitsWhat it does
EVD1Channel Event Detected Interrupt Disable
OVR0Channel Overrun Interrupt Disable

CHANNEL7.CHINTENSETChannel n Interrupt Enable Set

Address
0x4486005D
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5–
  4. 4–
  5. 3–
  6. 2–
  7. 1EVD
  8. 0OVR
2 fields
FieldBitsWhat it does
EVD1Channel Event Detected Interrupt Enable
OVR0Channel Overrun Interrupt Enable

CHANNEL7.CHINTFLAGChannel n Interrupt Flag Status and Clear

Address
0x4486005E
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5–
  4. 4–
  5. 3–
  6. 2–
  7. 1EVD
  8. 0OVR
2 fields
FieldBitsWhat it does
EVD1Channel Event Detected
OVR0Channel Overrun

CHANNEL7.CHSTATUSChannel n Status

Address
0x4486005F
Reset
0x01
Access
read only
  1. 7–
  2. 6–
  3. 5–
  4. 4–
  5. 3–
  6. 2–
  7. 1BUSYCH
  8. 0RDYUSR
2 fields
FieldBitsWhat it does
BUSYCH1Busy Channel
RDYUSR0Ready User

CHANNEL8.CHANNELChannel n Control

Address
0x44860060
Reset
0x00008000
Access
read/write
Size
32-bit
5 fields
FieldBitsWhat it does
ONDEMAND15Generic Clock On Demand
RUNSTDBY14Run in standby
EDGSEL11:10Edge Detection Selection
  • 0 No event output when using the resynchronized or synchronous path
  • 1 Event detection only on the rising edge of the signal from the event generator when using the resynchronized or synchronous path
  • 2 Event detection only on the falling edge of the signal from the event generator when using the resynchronized or synchronous path
  • 3 Event detection on rising and falling edges of the signal from the event generator when using the resynchronized or synchronous path
PATH9:8Path Selection
  • 0 Asynchronous path
  • 1 Resynchronized path
EVGEN7:0Event Generator Selection

CHANNEL8.CHINTENCLRChannel n Interrupt Enable Clear

Address
0x44860064
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5–
  4. 4–
  5. 3–
  6. 2–
  7. 1EVD
  8. 0OVR
2 fields
FieldBitsWhat it does
EVD1Channel Event Detected Interrupt Disable
OVR0Channel Overrun Interrupt Disable

CHANNEL8.CHINTENSETChannel n Interrupt Enable Set

Address
0x44860065
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5–
  4. 4–
  5. 3–
  6. 2–
  7. 1EVD
  8. 0OVR
2 fields
FieldBitsWhat it does
EVD1Channel Event Detected Interrupt Enable
OVR0Channel Overrun Interrupt Enable

CHANNEL8.CHINTFLAGChannel n Interrupt Flag Status and Clear

Address
0x44860066
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5–
  4. 4–
  5. 3–
  6. 2–
  7. 1EVD
  8. 0OVR
2 fields
FieldBitsWhat it does
EVD1Channel Event Detected
OVR0Channel Overrun

CHANNEL8.CHSTATUSChannel n Status

Address
0x44860067
Reset
0x01
Access
read only
  1. 7–
  2. 6–
  3. 5–
  4. 4–
  5. 3–
  6. 2–
  7. 1BUSYCH
  8. 0RDYUSR
2 fields
FieldBitsWhat it does
BUSYCH1Busy Channel
RDYUSR0Ready User

CHANNEL9.CHANNELChannel n Control

Address
0x44860068
Reset
0x00008000
Access
read/write
Size
32-bit
5 fields
FieldBitsWhat it does
ONDEMAND15Generic Clock On Demand
RUNSTDBY14Run in standby
EDGSEL11:10Edge Detection Selection
  • 0 No event output when using the resynchronized or synchronous path
  • 1 Event detection only on the rising edge of the signal from the event generator when using the resynchronized or synchronous path
  • 2 Event detection only on the falling edge of the signal from the event generator when using the resynchronized or synchronous path
  • 3 Event detection on rising and falling edges of the signal from the event generator when using the resynchronized or synchronous path
PATH9:8Path Selection
  • 0 Asynchronous path
  • 1 Resynchronized path
EVGEN7:0Event Generator Selection

CHANNEL9.CHINTENCLRChannel n Interrupt Enable Clear

Address
0x4486006C
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5–
  4. 4–
  5. 3–
  6. 2–
  7. 1EVD
  8. 0OVR
2 fields
FieldBitsWhat it does
EVD1Channel Event Detected Interrupt Disable
OVR0Channel Overrun Interrupt Disable

CHANNEL9.CHINTENSETChannel n Interrupt Enable Set

Address
0x4486006D
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5–
  4. 4–
  5. 3–
  6. 2–
  7. 1EVD
  8. 0OVR
2 fields
FieldBitsWhat it does
EVD1Channel Event Detected Interrupt Enable
OVR0Channel Overrun Interrupt Enable

CHANNEL9.CHINTFLAGChannel n Interrupt Flag Status and Clear

Address
0x4486006E
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5–
  4. 4–
  5. 3–
  6. 2–
  7. 1EVD
  8. 0OVR
2 fields
FieldBitsWhat it does
EVD1Channel Event Detected
OVR0Channel Overrun

CHANNEL9.CHSTATUSChannel n Status

Address
0x4486006F
Reset
0x01
Access
read only
  1. 7–
  2. 6–
  3. 5–
  4. 4–
  5. 3–
  6. 2–
  7. 1BUSYCH
  8. 0RDYUSR
2 fields
FieldBitsWhat it does
BUSYCH1Busy Channel
RDYUSR0Ready User

CHANNEL10.CHANNELChannel n Control

Address
0x44860070
Reset
0x00008000
Access
read/write
Size
32-bit
5 fields
FieldBitsWhat it does
ONDEMAND15Generic Clock On Demand
RUNSTDBY14Run in standby
EDGSEL11:10Edge Detection Selection
  • 0 No event output when using the resynchronized or synchronous path
  • 1 Event detection only on the rising edge of the signal from the event generator when using the resynchronized or synchronous path
  • 2 Event detection only on the falling edge of the signal from the event generator when using the resynchronized or synchronous path
  • 3 Event detection on rising and falling edges of the signal from the event generator when using the resynchronized or synchronous path
PATH9:8Path Selection
  • 0 Asynchronous path
  • 1 Resynchronized path
EVGEN7:0Event Generator Selection

CHANNEL10.CHINTENCLRChannel n Interrupt Enable Clear

Address
0x44860074
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5–
  4. 4–
  5. 3–
  6. 2–
  7. 1EVD
  8. 0OVR
2 fields
FieldBitsWhat it does
EVD1Channel Event Detected Interrupt Disable
OVR0Channel Overrun Interrupt Disable

CHANNEL10.CHINTENSETChannel n Interrupt Enable Set

Address
0x44860075
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5–
  4. 4–
  5. 3–
  6. 2–
  7. 1EVD
  8. 0OVR
2 fields
FieldBitsWhat it does
EVD1Channel Event Detected Interrupt Enable
OVR0Channel Overrun Interrupt Enable

CHANNEL10.CHINTFLAGChannel n Interrupt Flag Status and Clear

Address
0x44860076
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5–
  4. 4–
  5. 3–
  6. 2–
  7. 1EVD
  8. 0OVR
2 fields
FieldBitsWhat it does
EVD1Channel Event Detected
OVR0Channel Overrun

CHANNEL10.CHSTATUSChannel n Status

Address
0x44860077
Reset
0x01
Access
read only
  1. 7–
  2. 6–
  3. 5–
  4. 4–
  5. 3–
  6. 2–
  7. 1BUSYCH
  8. 0RDYUSR
2 fields
FieldBitsWhat it does
BUSYCH1Busy Channel
RDYUSR0Ready User

CHANNEL11.CHANNELChannel n Control

Address
0x44860078
Reset
0x00008000
Access
read/write
Size
32-bit
5 fields
FieldBitsWhat it does
ONDEMAND15Generic Clock On Demand
RUNSTDBY14Run in standby
EDGSEL11:10Edge Detection Selection
  • 0 No event output when using the resynchronized or synchronous path
  • 1 Event detection only on the rising edge of the signal from the event generator when using the resynchronized or synchronous path
  • 2 Event detection only on the falling edge of the signal from the event generator when using the resynchronized or synchronous path
  • 3 Event detection on rising and falling edges of the signal from the event generator when using the resynchronized or synchronous path
PATH9:8Path Selection
  • 0 Asynchronous path
  • 1 Resynchronized path
EVGEN7:0Event Generator Selection

CHANNEL11.CHINTENCLRChannel n Interrupt Enable Clear

Address
0x4486007C
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5–
  4. 4–
  5. 3–
  6. 2–
  7. 1EVD
  8. 0OVR
2 fields
FieldBitsWhat it does
EVD1Channel Event Detected Interrupt Disable
OVR0Channel Overrun Interrupt Disable

CHANNEL11.CHINTENSETChannel n Interrupt Enable Set

Address
0x4486007D
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5–
  4. 4–
  5. 3–
  6. 2–
  7. 1EVD
  8. 0OVR
2 fields
FieldBitsWhat it does
EVD1Channel Event Detected Interrupt Enable
OVR0Channel Overrun Interrupt Enable

CHANNEL11.CHINTFLAGChannel n Interrupt Flag Status and Clear

Address
0x4486007E
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5–
  4. 4–
  5. 3–
  6. 2–
  7. 1EVD
  8. 0OVR
2 fields
FieldBitsWhat it does
EVD1Channel Event Detected
OVR0Channel Overrun

CHANNEL11.CHSTATUSChannel n Status

Address
0x4486007F
Reset
0x01
Access
read only
  1. 7–
  2. 6–
  3. 5–
  4. 4–
  5. 3–
  6. 2–
  7. 1BUSYCH
  8. 0RDYUSR
2 fields
FieldBitsWhat it does
BUSYCH1Busy Channel
RDYUSR0Ready User

CHANNEL12.CHANNELChannel n Control

Address
0x44860080
Reset
0x00008000
Access
read/write
Size
32-bit
5 fields
FieldBitsWhat it does
ONDEMAND15Generic Clock On Demand
RUNSTDBY14Run in standby
EDGSEL11:10Edge Detection Selection
  • 0 No event output when using the resynchronized or synchronous path
  • 1 Event detection only on the rising edge of the signal from the event generator when using the resynchronized or synchronous path
  • 2 Event detection only on the falling edge of the signal from the event generator when using the resynchronized or synchronous path
  • 3 Event detection on rising and falling edges of the signal from the event generator when using the resynchronized or synchronous path
PATH9:8Path Selection
  • 0 Asynchronous path
  • 1 Resynchronized path
EVGEN7:0Event Generator Selection

CHANNEL12.CHINTENCLRChannel n Interrupt Enable Clear

Address
0x44860084
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5–
  4. 4–
  5. 3–
  6. 2–
  7. 1EVD
  8. 0OVR
2 fields
FieldBitsWhat it does
EVD1Channel Event Detected Interrupt Disable
OVR0Channel Overrun Interrupt Disable

CHANNEL12.CHINTENSETChannel n Interrupt Enable Set

Address
0x44860085
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5–
  4. 4–
  5. 3–
  6. 2–
  7. 1EVD
  8. 0OVR
2 fields
FieldBitsWhat it does
EVD1Channel Event Detected Interrupt Enable
OVR0Channel Overrun Interrupt Enable

CHANNEL12.CHINTFLAGChannel n Interrupt Flag Status and Clear

Address
0x44860086
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5–
  4. 4–
  5. 3–
  6. 2–
  7. 1EVD
  8. 0OVR
2 fields
FieldBitsWhat it does
EVD1Channel Event Detected
OVR0Channel Overrun

CHANNEL12.CHSTATUSChannel n Status

Address
0x44860087
Reset
0x01
Access
read only
  1. 7–
  2. 6–
  3. 5–
  4. 4–
  5. 3–
  6. 2–
  7. 1BUSYCH
  8. 0RDYUSR
2 fields
FieldBitsWhat it does
BUSYCH1Busy Channel
RDYUSR0Ready User

CHANNEL13.CHANNELChannel n Control

Address
0x44860088
Reset
0x00008000
Access
read/write
Size
32-bit
5 fields
FieldBitsWhat it does
ONDEMAND15Generic Clock On Demand
RUNSTDBY14Run in standby
EDGSEL11:10Edge Detection Selection
  • 0 No event output when using the resynchronized or synchronous path
  • 1 Event detection only on the rising edge of the signal from the event generator when using the resynchronized or synchronous path
  • 2 Event detection only on the falling edge of the signal from the event generator when using the resynchronized or synchronous path
  • 3 Event detection on rising and falling edges of the signal from the event generator when using the resynchronized or synchronous path
PATH9:8Path Selection
  • 0 Asynchronous path
  • 1 Resynchronized path
EVGEN7:0Event Generator Selection

CHANNEL13.CHINTENCLRChannel n Interrupt Enable Clear

Address
0x4486008C
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5–
  4. 4–
  5. 3–
  6. 2–
  7. 1EVD
  8. 0OVR
2 fields
FieldBitsWhat it does
EVD1Channel Event Detected Interrupt Disable
OVR0Channel Overrun Interrupt Disable

CHANNEL13.CHINTENSETChannel n Interrupt Enable Set

Address
0x4486008D
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5–
  4. 4–
  5. 3–
  6. 2–
  7. 1EVD
  8. 0OVR
2 fields
FieldBitsWhat it does
EVD1Channel Event Detected Interrupt Enable
OVR0Channel Overrun Interrupt Enable

CHANNEL13.CHINTFLAGChannel n Interrupt Flag Status and Clear

Address
0x4486008E
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5–
  4. 4–
  5. 3–
  6. 2–
  7. 1EVD
  8. 0OVR
2 fields
FieldBitsWhat it does
EVD1Channel Event Detected
OVR0Channel Overrun

CHANNEL13.CHSTATUSChannel n Status

Address
0x4486008F
Reset
0x01
Access
read only
  1. 7–
  2. 6–
  3. 5–
  4. 4–
  5. 3–
  6. 2–
  7. 1BUSYCH
  8. 0RDYUSR
2 fields
FieldBitsWhat it does
BUSYCH1Busy Channel
RDYUSR0Ready User

CHANNEL14.CHANNELChannel n Control

Address
0x44860090
Reset
0x00008000
Access
read/write
Size
32-bit
5 fields
FieldBitsWhat it does
ONDEMAND15Generic Clock On Demand
RUNSTDBY14Run in standby
EDGSEL11:10Edge Detection Selection
  • 0 No event output when using the resynchronized or synchronous path
  • 1 Event detection only on the rising edge of the signal from the event generator when using the resynchronized or synchronous path
  • 2 Event detection only on the falling edge of the signal from the event generator when using the resynchronized or synchronous path
  • 3 Event detection on rising and falling edges of the signal from the event generator when using the resynchronized or synchronous path
PATH9:8Path Selection
  • 0 Asynchronous path
  • 1 Resynchronized path
EVGEN7:0Event Generator Selection

CHANNEL14.CHINTENCLRChannel n Interrupt Enable Clear

Address
0x44860094
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5–
  4. 4–
  5. 3–
  6. 2–
  7. 1EVD
  8. 0OVR
2 fields
FieldBitsWhat it does
EVD1Channel Event Detected Interrupt Disable
OVR0Channel Overrun Interrupt Disable

CHANNEL14.CHINTENSETChannel n Interrupt Enable Set

Address
0x44860095
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5–
  4. 4–
  5. 3–
  6. 2–
  7. 1EVD
  8. 0OVR
2 fields
FieldBitsWhat it does
EVD1Channel Event Detected Interrupt Enable
OVR0Channel Overrun Interrupt Enable

CHANNEL14.CHINTFLAGChannel n Interrupt Flag Status and Clear

Address
0x44860096
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5–
  4. 4–
  5. 3–
  6. 2–
  7. 1EVD
  8. 0OVR
2 fields
FieldBitsWhat it does
EVD1Channel Event Detected
OVR0Channel Overrun

CHANNEL14.CHSTATUSChannel n Status

Address
0x44860097
Reset
0x01
Access
read only
  1. 7–
  2. 6–
  3. 5–
  4. 4–
  5. 3–
  6. 2–
  7. 1BUSYCH
  8. 0RDYUSR
2 fields
FieldBitsWhat it does
BUSYCH1Busy Channel
RDYUSR0Ready User

CHANNEL15.CHANNELChannel n Control

Address
0x44860098
Reset
0x00008000
Access
read/write
Size
32-bit
5 fields
FieldBitsWhat it does
ONDEMAND15Generic Clock On Demand
RUNSTDBY14Run in standby
EDGSEL11:10Edge Detection Selection
  • 0 No event output when using the resynchronized or synchronous path
  • 1 Event detection only on the rising edge of the signal from the event generator when using the resynchronized or synchronous path
  • 2 Event detection only on the falling edge of the signal from the event generator when using the resynchronized or synchronous path
  • 3 Event detection on rising and falling edges of the signal from the event generator when using the resynchronized or synchronous path
PATH9:8Path Selection
  • 0 Asynchronous path
  • 1 Resynchronized path
EVGEN7:0Event Generator Selection

CHANNEL15.CHINTENCLRChannel n Interrupt Enable Clear

Address
0x4486009C
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5–
  4. 4–
  5. 3–
  6. 2–
  7. 1EVD
  8. 0OVR
2 fields
FieldBitsWhat it does
EVD1Channel Event Detected Interrupt Disable
OVR0Channel Overrun Interrupt Disable

CHANNEL15.CHINTENSETChannel n Interrupt Enable Set

Address
0x4486009D
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5–
  4. 4–
  5. 3–
  6. 2–
  7. 1EVD
  8. 0OVR
2 fields
FieldBitsWhat it does
EVD1Channel Event Detected Interrupt Enable
OVR0Channel Overrun Interrupt Enable

CHANNEL15.CHINTFLAGChannel n Interrupt Flag Status and Clear

Address
0x4486009E
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5–
  4. 4–
  5. 3–
  6. 2–
  7. 1EVD
  8. 0OVR
2 fields
FieldBitsWhat it does
EVD1Channel Event Detected
OVR0Channel Overrun

CHANNEL15.CHSTATUSChannel n Status

Address
0x4486009F
Reset
0x01
Access
read only
  1. 7–
  2. 6–
  3. 5–
  4. 4–
  5. 3–
  6. 2–
  7. 1BUSYCH
  8. 0RDYUSR
2 fields
FieldBitsWhat it does
BUSYCH1Busy Channel
RDYUSR0Ready User

CHANNEL16.CHANNELChannel n Control

Address
0x448600A0
Reset
0x00008000
Access
read/write
Size
32-bit
5 fields
FieldBitsWhat it does
ONDEMAND15Generic Clock On Demand
RUNSTDBY14Run in standby
EDGSEL11:10Edge Detection Selection
  • 0 No event output when using the resynchronized or synchronous path
  • 1 Event detection only on the rising edge of the signal from the event generator when using the resynchronized or synchronous path
  • 2 Event detection only on the falling edge of the signal from the event generator when using the resynchronized or synchronous path
  • 3 Event detection on rising and falling edges of the signal from the event generator when using the resynchronized or synchronous path
PATH9:8Path Selection
  • 0 Asynchronous path
  • 1 Resynchronized path
EVGEN7:0Event Generator Selection

CHANNEL16.CHINTENCLRChannel n Interrupt Enable Clear

Address
0x448600A4
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5–
  4. 4–
  5. 3–
  6. 2–
  7. 1EVD
  8. 0OVR
2 fields
FieldBitsWhat it does
EVD1Channel Event Detected Interrupt Disable
OVR0Channel Overrun Interrupt Disable

CHANNEL16.CHINTENSETChannel n Interrupt Enable Set

Address
0x448600A5
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5–
  4. 4–
  5. 3–
  6. 2–
  7. 1EVD
  8. 0OVR
2 fields
FieldBitsWhat it does
EVD1Channel Event Detected Interrupt Enable
OVR0Channel Overrun Interrupt Enable

CHANNEL16.CHINTFLAGChannel n Interrupt Flag Status and Clear

Address
0x448600A6
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5–
  4. 4–
  5. 3–
  6. 2–
  7. 1EVD
  8. 0OVR
2 fields
FieldBitsWhat it does
EVD1Channel Event Detected
OVR0Channel Overrun

CHANNEL16.CHSTATUSChannel n Status

Address
0x448600A7
Reset
0x01
Access
read only
  1. 7–
  2. 6–
  3. 5–
  4. 4–
  5. 3–
  6. 2–
  7. 1BUSYCH
  8. 0RDYUSR
2 fields
FieldBitsWhat it does
BUSYCH1Busy Channel
RDYUSR0Ready User

CHANNEL17.CHANNELChannel n Control

Address
0x448600A8
Reset
0x00008000
Access
read/write
Size
32-bit
5 fields
FieldBitsWhat it does
ONDEMAND15Generic Clock On Demand
RUNSTDBY14Run in standby
EDGSEL11:10Edge Detection Selection
  • 0 No event output when using the resynchronized or synchronous path
  • 1 Event detection only on the rising edge of the signal from the event generator when using the resynchronized or synchronous path
  • 2 Event detection only on the falling edge of the signal from the event generator when using the resynchronized or synchronous path
  • 3 Event detection on rising and falling edges of the signal from the event generator when using the resynchronized or synchronous path
PATH9:8Path Selection
  • 0 Asynchronous path
  • 1 Resynchronized path
EVGEN7:0Event Generator Selection

CHANNEL17.CHINTENCLRChannel n Interrupt Enable Clear

Address
0x448600AC
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5–
  4. 4–
  5. 3–
  6. 2–
  7. 1EVD
  8. 0OVR
2 fields
FieldBitsWhat it does
EVD1Channel Event Detected Interrupt Disable
OVR0Channel Overrun Interrupt Disable

CHANNEL17.CHINTENSETChannel n Interrupt Enable Set

Address
0x448600AD
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5–
  4. 4–
  5. 3–
  6. 2–
  7. 1EVD
  8. 0OVR
2 fields
FieldBitsWhat it does
EVD1Channel Event Detected Interrupt Enable
OVR0Channel Overrun Interrupt Enable

CHANNEL17.CHINTFLAGChannel n Interrupt Flag Status and Clear

Address
0x448600AE
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5–
  4. 4–
  5. 3–
  6. 2–
  7. 1EVD
  8. 0OVR
2 fields
FieldBitsWhat it does
EVD1Channel Event Detected
OVR0Channel Overrun

CHANNEL17.CHSTATUSChannel n Status

Address
0x448600AF
Reset
0x01
Access
read only
  1. 7–
  2. 6–
  3. 5–
  4. 4–
  5. 3–
  6. 2–
  7. 1BUSYCH
  8. 0RDYUSR
2 fields
FieldBitsWhat it does
BUSYCH1Busy Channel
RDYUSR0Ready User

CHANNEL18.CHANNELChannel n Control

Address
0x448600B0
Reset
0x00008000
Access
read/write
Size
32-bit
5 fields
FieldBitsWhat it does
ONDEMAND15Generic Clock On Demand
RUNSTDBY14Run in standby
EDGSEL11:10Edge Detection Selection
  • 0 No event output when using the resynchronized or synchronous path
  • 1 Event detection only on the rising edge of the signal from the event generator when using the resynchronized or synchronous path
  • 2 Event detection only on the falling edge of the signal from the event generator when using the resynchronized or synchronous path
  • 3 Event detection on rising and falling edges of the signal from the event generator when using the resynchronized or synchronous path
PATH9:8Path Selection
  • 0 Asynchronous path
  • 1 Resynchronized path
EVGEN7:0Event Generator Selection

CHANNEL18.CHINTENCLRChannel n Interrupt Enable Clear

Address
0x448600B4
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5–
  4. 4–
  5. 3–
  6. 2–
  7. 1EVD
  8. 0OVR
2 fields
FieldBitsWhat it does
EVD1Channel Event Detected Interrupt Disable
OVR0Channel Overrun Interrupt Disable

CHANNEL18.CHINTENSETChannel n Interrupt Enable Set

Address
0x448600B5
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5–
  4. 4–
  5. 3–
  6. 2–
  7. 1EVD
  8. 0OVR
2 fields
FieldBitsWhat it does
EVD1Channel Event Detected Interrupt Enable
OVR0Channel Overrun Interrupt Enable

CHANNEL18.CHINTFLAGChannel n Interrupt Flag Status and Clear

Address
0x448600B6
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5–
  4. 4–
  5. 3–
  6. 2–
  7. 1EVD
  8. 0OVR
2 fields
FieldBitsWhat it does
EVD1Channel Event Detected
OVR0Channel Overrun

CHANNEL18.CHSTATUSChannel n Status

Address
0x448600B7
Reset
0x01
Access
read only
  1. 7–
  2. 6–
  3. 5–
  4. 4–
  5. 3–
  6. 2–
  7. 1BUSYCH
  8. 0RDYUSR
2 fields
FieldBitsWhat it does
BUSYCH1Busy Channel
RDYUSR0Ready User

CHANNEL19.CHANNELChannel n Control

Address
0x448600B8
Reset
0x00008000
Access
read/write
Size
32-bit
5 fields
FieldBitsWhat it does
ONDEMAND15Generic Clock On Demand
RUNSTDBY14Run in standby
EDGSEL11:10Edge Detection Selection
  • 0 No event output when using the resynchronized or synchronous path
  • 1 Event detection only on the rising edge of the signal from the event generator when using the resynchronized or synchronous path
  • 2 Event detection only on the falling edge of the signal from the event generator when using the resynchronized or synchronous path
  • 3 Event detection on rising and falling edges of the signal from the event generator when using the resynchronized or synchronous path
PATH9:8Path Selection
  • 0 Asynchronous path
  • 1 Resynchronized path
EVGEN7:0Event Generator Selection

CHANNEL19.CHINTENCLRChannel n Interrupt Enable Clear

Address
0x448600BC
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5–
  4. 4–
  5. 3–
  6. 2–
  7. 1EVD
  8. 0OVR
2 fields
FieldBitsWhat it does
EVD1Channel Event Detected Interrupt Disable
OVR0Channel Overrun Interrupt Disable

CHANNEL19.CHINTENSETChannel n Interrupt Enable Set

Address
0x448600BD
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5–
  4. 4–
  5. 3–
  6. 2–
  7. 1EVD
  8. 0OVR
2 fields
FieldBitsWhat it does
EVD1Channel Event Detected Interrupt Enable
OVR0Channel Overrun Interrupt Enable

CHANNEL19.CHINTFLAGChannel n Interrupt Flag Status and Clear

Address
0x448600BE
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5–
  4. 4–
  5. 3–
  6. 2–
  7. 1EVD
  8. 0OVR
2 fields
FieldBitsWhat it does
EVD1Channel Event Detected
OVR0Channel Overrun

CHANNEL19.CHSTATUSChannel n Status

Address
0x448600BF
Reset
0x01
Access
read only
  1. 7–
  2. 6–
  3. 5–
  4. 4–
  5. 3–
  6. 2–
  7. 1BUSYCH
  8. 0RDYUSR
2 fields
FieldBitsWhat it does
BUSYCH1Busy Channel
RDYUSR0Ready User

CHANNEL20.CHANNELChannel n Control

Address
0x448600C0
Reset
0x00008000
Access
read/write
Size
32-bit
5 fields
FieldBitsWhat it does
ONDEMAND15Generic Clock On Demand
RUNSTDBY14Run in standby
EDGSEL11:10Edge Detection Selection
  • 0 No event output when using the resynchronized or synchronous path
  • 1 Event detection only on the rising edge of the signal from the event generator when using the resynchronized or synchronous path
  • 2 Event detection only on the falling edge of the signal from the event generator when using the resynchronized or synchronous path
  • 3 Event detection on rising and falling edges of the signal from the event generator when using the resynchronized or synchronous path
PATH9:8Path Selection
  • 0 Asynchronous path
  • 1 Resynchronized path
EVGEN7:0Event Generator Selection

CHANNEL20.CHINTENCLRChannel n Interrupt Enable Clear

Address
0x448600C4
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5–
  4. 4–
  5. 3–
  6. 2–
  7. 1EVD
  8. 0OVR
2 fields
FieldBitsWhat it does
EVD1Channel Event Detected Interrupt Disable
OVR0Channel Overrun Interrupt Disable

CHANNEL20.CHINTENSETChannel n Interrupt Enable Set

Address
0x448600C5
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5–
  4. 4–
  5. 3–
  6. 2–
  7. 1EVD
  8. 0OVR
2 fields
FieldBitsWhat it does
EVD1Channel Event Detected Interrupt Enable
OVR0Channel Overrun Interrupt Enable

CHANNEL20.CHINTFLAGChannel n Interrupt Flag Status and Clear

Address
0x448600C6
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5–
  4. 4–
  5. 3–
  6. 2–
  7. 1EVD
  8. 0OVR
2 fields
FieldBitsWhat it does
EVD1Channel Event Detected
OVR0Channel Overrun

CHANNEL20.CHSTATUSChannel n Status

Address
0x448600C7
Reset
0x01
Access
read only
  1. 7–
  2. 6–
  3. 5–
  4. 4–
  5. 3–
  6. 2–
  7. 1BUSYCH
  8. 0RDYUSR
2 fields
FieldBitsWhat it does
BUSYCH1Busy Channel
RDYUSR0Ready User

CHANNEL21.CHANNELChannel n Control

Address
0x448600C8
Reset
0x00008000
Access
read/write
Size
32-bit
5 fields
FieldBitsWhat it does
ONDEMAND15Generic Clock On Demand
RUNSTDBY14Run in standby
EDGSEL11:10Edge Detection Selection
  • 0 No event output when using the resynchronized or synchronous path
  • 1 Event detection only on the rising edge of the signal from the event generator when using the resynchronized or synchronous path
  • 2 Event detection only on the falling edge of the signal from the event generator when using the resynchronized or synchronous path
  • 3 Event detection on rising and falling edges of the signal from the event generator when using the resynchronized or synchronous path
PATH9:8Path Selection
  • 0 Asynchronous path
  • 1 Resynchronized path
EVGEN7:0Event Generator Selection

CHANNEL21.CHINTENCLRChannel n Interrupt Enable Clear

Address
0x448600CC
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5–
  4. 4–
  5. 3–
  6. 2–
  7. 1EVD
  8. 0OVR
2 fields
FieldBitsWhat it does
EVD1Channel Event Detected Interrupt Disable
OVR0Channel Overrun Interrupt Disable

CHANNEL21.CHINTENSETChannel n Interrupt Enable Set

Address
0x448600CD
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5–
  4. 4–
  5. 3–
  6. 2–
  7. 1EVD
  8. 0OVR
2 fields
FieldBitsWhat it does
EVD1Channel Event Detected Interrupt Enable
OVR0Channel Overrun Interrupt Enable

CHANNEL21.CHINTFLAGChannel n Interrupt Flag Status and Clear

Address
0x448600CE
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5–
  4. 4–
  5. 3–
  6. 2–
  7. 1EVD
  8. 0OVR
2 fields
FieldBitsWhat it does
EVD1Channel Event Detected
OVR0Channel Overrun

CHANNEL21.CHSTATUSChannel n Status

Address
0x448600CF
Reset
0x01
Access
read only
  1. 7–
  2. 6–
  3. 5–
  4. 4–
  5. 3–
  6. 2–
  7. 1BUSYCH
  8. 0RDYUSR
2 fields
FieldBitsWhat it does
BUSYCH1Busy Channel
RDYUSR0Ready User

CHANNEL22.CHANNELChannel n Control

Address
0x448600D0
Reset
0x00008000
Access
read/write
Size
32-bit
5 fields
FieldBitsWhat it does
ONDEMAND15Generic Clock On Demand
RUNSTDBY14Run in standby
EDGSEL11:10Edge Detection Selection
  • 0 No event output when using the resynchronized or synchronous path
  • 1 Event detection only on the rising edge of the signal from the event generator when using the resynchronized or synchronous path
  • 2 Event detection only on the falling edge of the signal from the event generator when using the resynchronized or synchronous path
  • 3 Event detection on rising and falling edges of the signal from the event generator when using the resynchronized or synchronous path
PATH9:8Path Selection
  • 0 Asynchronous path
  • 1 Resynchronized path
EVGEN7:0Event Generator Selection

CHANNEL22.CHINTENCLRChannel n Interrupt Enable Clear

Address
0x448600D4
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5–
  4. 4–
  5. 3–
  6. 2–
  7. 1EVD
  8. 0OVR
2 fields
FieldBitsWhat it does
EVD1Channel Event Detected Interrupt Disable
OVR0Channel Overrun Interrupt Disable

CHANNEL22.CHINTENSETChannel n Interrupt Enable Set

Address
0x448600D5
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5–
  4. 4–
  5. 3–
  6. 2–
  7. 1EVD
  8. 0OVR
2 fields
FieldBitsWhat it does
EVD1Channel Event Detected Interrupt Enable
OVR0Channel Overrun Interrupt Enable

CHANNEL22.CHINTFLAGChannel n Interrupt Flag Status and Clear

Address
0x448600D6
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5–
  4. 4–
  5. 3–
  6. 2–
  7. 1EVD
  8. 0OVR
2 fields
FieldBitsWhat it does
EVD1Channel Event Detected
OVR0Channel Overrun

CHANNEL22.CHSTATUSChannel n Status

Address
0x448600D7
Reset
0x01
Access
read only
  1. 7–
  2. 6–
  3. 5–
  4. 4–
  5. 3–
  6. 2–
  7. 1BUSYCH
  8. 0RDYUSR
2 fields
FieldBitsWhat it does
BUSYCH1Busy Channel
RDYUSR0Ready User

CHANNEL23.CHANNELChannel n Control

Address
0x448600D8
Reset
0x00008000
Access
read/write
Size
32-bit
5 fields
FieldBitsWhat it does
ONDEMAND15Generic Clock On Demand
RUNSTDBY14Run in standby
EDGSEL11:10Edge Detection Selection
  • 0 No event output when using the resynchronized or synchronous path
  • 1 Event detection only on the rising edge of the signal from the event generator when using the resynchronized or synchronous path
  • 2 Event detection only on the falling edge of the signal from the event generator when using the resynchronized or synchronous path
  • 3 Event detection on rising and falling edges of the signal from the event generator when using the resynchronized or synchronous path
PATH9:8Path Selection
  • 0 Asynchronous path
  • 1 Resynchronized path
EVGEN7:0Event Generator Selection

CHANNEL23.CHINTENCLRChannel n Interrupt Enable Clear

Address
0x448600DC
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5–
  4. 4–
  5. 3–
  6. 2–
  7. 1EVD
  8. 0OVR
2 fields
FieldBitsWhat it does
EVD1Channel Event Detected Interrupt Disable
OVR0Channel Overrun Interrupt Disable

CHANNEL23.CHINTENSETChannel n Interrupt Enable Set

Address
0x448600DD
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5–
  4. 4–
  5. 3–
  6. 2–
  7. 1EVD
  8. 0OVR
2 fields
FieldBitsWhat it does
EVD1Channel Event Detected Interrupt Enable
OVR0Channel Overrun Interrupt Enable

CHANNEL23.CHINTFLAGChannel n Interrupt Flag Status and Clear

Address
0x448600DE
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5–
  4. 4–
  5. 3–
  6. 2–
  7. 1EVD
  8. 0OVR
2 fields
FieldBitsWhat it does
EVD1Channel Event Detected
OVR0Channel Overrun

CHANNEL23.CHSTATUSChannel n Status

Address
0x448600DF
Reset
0x01
Access
read only
  1. 7–
  2. 6–
  3. 5–
  4. 4–
  5. 3–
  6. 2–
  7. 1BUSYCH
  8. 0RDYUSR
2 fields
FieldBitsWhat it does
BUSYCH1Busy Channel
RDYUSR0Ready User

CHANNEL24.CHANNELChannel n Control

Address
0x448600E0
Reset
0x00008000
Access
read/write
Size
32-bit
5 fields
FieldBitsWhat it does
ONDEMAND15Generic Clock On Demand
RUNSTDBY14Run in standby
EDGSEL11:10Edge Detection Selection
  • 0 No event output when using the resynchronized or synchronous path
  • 1 Event detection only on the rising edge of the signal from the event generator when using the resynchronized or synchronous path
  • 2 Event detection only on the falling edge of the signal from the event generator when using the resynchronized or synchronous path
  • 3 Event detection on rising and falling edges of the signal from the event generator when using the resynchronized or synchronous path
PATH9:8Path Selection
  • 0 Asynchronous path
  • 1 Resynchronized path
EVGEN7:0Event Generator Selection

CHANNEL24.CHINTENCLRChannel n Interrupt Enable Clear

Address
0x448600E4
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5–
  4. 4–
  5. 3–
  6. 2–
  7. 1EVD
  8. 0OVR
2 fields
FieldBitsWhat it does
EVD1Channel Event Detected Interrupt Disable
OVR0Channel Overrun Interrupt Disable

CHANNEL24.CHINTENSETChannel n Interrupt Enable Set

Address
0x448600E5
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5–
  4. 4–
  5. 3–
  6. 2–
  7. 1EVD
  8. 0OVR
2 fields
FieldBitsWhat it does
EVD1Channel Event Detected Interrupt Enable
OVR0Channel Overrun Interrupt Enable

CHANNEL24.CHINTFLAGChannel n Interrupt Flag Status and Clear

Address
0x448600E6
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5–
  4. 4–
  5. 3–
  6. 2–
  7. 1EVD
  8. 0OVR
2 fields
FieldBitsWhat it does
EVD1Channel Event Detected
OVR0Channel Overrun

CHANNEL24.CHSTATUSChannel n Status

Address
0x448600E7
Reset
0x01
Access
read only
  1. 7–
  2. 6–
  3. 5–
  4. 4–
  5. 3–
  6. 2–
  7. 1BUSYCH
  8. 0RDYUSR
2 fields
FieldBitsWhat it does
BUSYCH1Busy Channel
RDYUSR0Ready User

CHANNEL25.CHANNELChannel n Control

Address
0x448600E8
Reset
0x00008000
Access
read/write
Size
32-bit
5 fields
FieldBitsWhat it does
ONDEMAND15Generic Clock On Demand
RUNSTDBY14Run in standby
EDGSEL11:10Edge Detection Selection
  • 0 No event output when using the resynchronized or synchronous path
  • 1 Event detection only on the rising edge of the signal from the event generator when using the resynchronized or synchronous path
  • 2 Event detection only on the falling edge of the signal from the event generator when using the resynchronized or synchronous path
  • 3 Event detection on rising and falling edges of the signal from the event generator when using the resynchronized or synchronous path
PATH9:8Path Selection
  • 0 Asynchronous path
  • 1 Resynchronized path
EVGEN7:0Event Generator Selection

CHANNEL25.CHINTENCLRChannel n Interrupt Enable Clear

Address
0x448600EC
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5–
  4. 4–
  5. 3–
  6. 2–
  7. 1EVD
  8. 0OVR
2 fields
FieldBitsWhat it does
EVD1Channel Event Detected Interrupt Disable
OVR0Channel Overrun Interrupt Disable

CHANNEL25.CHINTENSETChannel n Interrupt Enable Set

Address
0x448600ED
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5–
  4. 4–
  5. 3–
  6. 2–
  7. 1EVD
  8. 0OVR
2 fields
FieldBitsWhat it does
EVD1Channel Event Detected Interrupt Enable
OVR0Channel Overrun Interrupt Enable

CHANNEL25.CHINTFLAGChannel n Interrupt Flag Status and Clear

Address
0x448600EE
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5–
  4. 4–
  5. 3–
  6. 2–
  7. 1EVD
  8. 0OVR
2 fields
FieldBitsWhat it does
EVD1Channel Event Detected
OVR0Channel Overrun

CHANNEL25.CHSTATUSChannel n Status

Address
0x448600EF
Reset
0x01
Access
read only
  1. 7–
  2. 6–
  3. 5–
  4. 4–
  5. 3–
  6. 2–
  7. 1BUSYCH
  8. 0RDYUSR
2 fields
FieldBitsWhat it does
BUSYCH1Busy Channel
RDYUSR0Ready User

CHANNEL26.CHANNELChannel n Control

Address
0x448600F0
Reset
0x00008000
Access
read/write
Size
32-bit
5 fields
FieldBitsWhat it does
ONDEMAND15Generic Clock On Demand
RUNSTDBY14Run in standby
EDGSEL11:10Edge Detection Selection
  • 0 No event output when using the resynchronized or synchronous path
  • 1 Event detection only on the rising edge of the signal from the event generator when using the resynchronized or synchronous path
  • 2 Event detection only on the falling edge of the signal from the event generator when using the resynchronized or synchronous path
  • 3 Event detection on rising and falling edges of the signal from the event generator when using the resynchronized or synchronous path
PATH9:8Path Selection
  • 0 Asynchronous path
  • 1 Resynchronized path
EVGEN7:0Event Generator Selection

CHANNEL26.CHINTENCLRChannel n Interrupt Enable Clear

Address
0x448600F4
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5–
  4. 4–
  5. 3–
  6. 2–
  7. 1EVD
  8. 0OVR
2 fields
FieldBitsWhat it does
EVD1Channel Event Detected Interrupt Disable
OVR0Channel Overrun Interrupt Disable

CHANNEL26.CHINTENSETChannel n Interrupt Enable Set

Address
0x448600F5
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5–
  4. 4–
  5. 3–
  6. 2–
  7. 1EVD
  8. 0OVR
2 fields
FieldBitsWhat it does
EVD1Channel Event Detected Interrupt Enable
OVR0Channel Overrun Interrupt Enable

CHANNEL26.CHINTFLAGChannel n Interrupt Flag Status and Clear

Address
0x448600F6
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5–
  4. 4–
  5. 3–
  6. 2–
  7. 1EVD
  8. 0OVR
2 fields
FieldBitsWhat it does
EVD1Channel Event Detected
OVR0Channel Overrun

CHANNEL26.CHSTATUSChannel n Status

Address
0x448600F7
Reset
0x01
Access
read only
  1. 7–
  2. 6–
  3. 5–
  4. 4–
  5. 3–
  6. 2–
  7. 1BUSYCH
  8. 0RDYUSR
2 fields
FieldBitsWhat it does
BUSYCH1Busy Channel
RDYUSR0Ready User

CHANNEL27.CHANNELChannel n Control

Address
0x448600F8
Reset
0x00008000
Access
read/write
Size
32-bit
5 fields
FieldBitsWhat it does
ONDEMAND15Generic Clock On Demand
RUNSTDBY14Run in standby
EDGSEL11:10Edge Detection Selection
  • 0 No event output when using the resynchronized or synchronous path
  • 1 Event detection only on the rising edge of the signal from the event generator when using the resynchronized or synchronous path
  • 2 Event detection only on the falling edge of the signal from the event generator when using the resynchronized or synchronous path
  • 3 Event detection on rising and falling edges of the signal from the event generator when using the resynchronized or synchronous path
PATH9:8Path Selection
  • 0 Asynchronous path
  • 1 Resynchronized path
EVGEN7:0Event Generator Selection

CHANNEL27.CHINTENCLRChannel n Interrupt Enable Clear

Address
0x448600FC
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5–
  4. 4–
  5. 3–
  6. 2–
  7. 1EVD
  8. 0OVR
2 fields
FieldBitsWhat it does
EVD1Channel Event Detected Interrupt Disable
OVR0Channel Overrun Interrupt Disable

CHANNEL27.CHINTENSETChannel n Interrupt Enable Set

Address
0x448600FD
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5–
  4. 4–
  5. 3–
  6. 2–
  7. 1EVD
  8. 0OVR
2 fields
FieldBitsWhat it does
EVD1Channel Event Detected Interrupt Enable
OVR0Channel Overrun Interrupt Enable

CHANNEL27.CHINTFLAGChannel n Interrupt Flag Status and Clear

Address
0x448600FE
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5–
  4. 4–
  5. 3–
  6. 2–
  7. 1EVD
  8. 0OVR
2 fields
FieldBitsWhat it does
EVD1Channel Event Detected
OVR0Channel Overrun

CHANNEL27.CHSTATUSChannel n Status

Address
0x448600FF
Reset
0x01
Access
read only
  1. 7–
  2. 6–
  3. 5–
  4. 4–
  5. 3–
  6. 2–
  7. 1BUSYCH
  8. 0RDYUSR
2 fields
FieldBitsWhat it does
BUSYCH1Busy Channel
RDYUSR0Ready User

CHANNEL28.CHANNELChannel n Control

Address
0x44860100
Reset
0x00008000
Access
read/write
Size
32-bit
5 fields
FieldBitsWhat it does
ONDEMAND15Generic Clock On Demand
RUNSTDBY14Run in standby
EDGSEL11:10Edge Detection Selection
  • 0 No event output when using the resynchronized or synchronous path
  • 1 Event detection only on the rising edge of the signal from the event generator when using the resynchronized or synchronous path
  • 2 Event detection only on the falling edge of the signal from the event generator when using the resynchronized or synchronous path
  • 3 Event detection on rising and falling edges of the signal from the event generator when using the resynchronized or synchronous path
PATH9:8Path Selection
  • 0 Asynchronous path
  • 1 Resynchronized path
EVGEN7:0Event Generator Selection

CHANNEL28.CHINTENCLRChannel n Interrupt Enable Clear

Address
0x44860104
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5–
  4. 4–
  5. 3–
  6. 2–
  7. 1EVD
  8. 0OVR
2 fields
FieldBitsWhat it does
EVD1Channel Event Detected Interrupt Disable
OVR0Channel Overrun Interrupt Disable

CHANNEL28.CHINTENSETChannel n Interrupt Enable Set

Address
0x44860105
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5–
  4. 4–
  5. 3–
  6. 2–
  7. 1EVD
  8. 0OVR
2 fields
FieldBitsWhat it does
EVD1Channel Event Detected Interrupt Enable
OVR0Channel Overrun Interrupt Enable

CHANNEL28.CHINTFLAGChannel n Interrupt Flag Status and Clear

Address
0x44860106
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5–
  4. 4–
  5. 3–
  6. 2–
  7. 1EVD
  8. 0OVR
2 fields
FieldBitsWhat it does
EVD1Channel Event Detected
OVR0Channel Overrun

CHANNEL28.CHSTATUSChannel n Status

Address
0x44860107
Reset
0x01
Access
read only
  1. 7–
  2. 6–
  3. 5–
  4. 4–
  5. 3–
  6. 2–
  7. 1BUSYCH
  8. 0RDYUSR
2 fields
FieldBitsWhat it does
BUSYCH1Busy Channel
RDYUSR0Ready User

CHANNEL29.CHANNELChannel n Control

Address
0x44860108
Reset
0x00008000
Access
read/write
Size
32-bit
5 fields
FieldBitsWhat it does
ONDEMAND15Generic Clock On Demand
RUNSTDBY14Run in standby
EDGSEL11:10Edge Detection Selection
  • 0 No event output when using the resynchronized or synchronous path
  • 1 Event detection only on the rising edge of the signal from the event generator when using the resynchronized or synchronous path
  • 2 Event detection only on the falling edge of the signal from the event generator when using the resynchronized or synchronous path
  • 3 Event detection on rising and falling edges of the signal from the event generator when using the resynchronized or synchronous path
PATH9:8Path Selection
  • 0 Asynchronous path
  • 1 Resynchronized path
EVGEN7:0Event Generator Selection

CHANNEL29.CHINTENCLRChannel n Interrupt Enable Clear

Address
0x4486010C
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5–
  4. 4–
  5. 3–
  6. 2–
  7. 1EVD
  8. 0OVR
2 fields
FieldBitsWhat it does
EVD1Channel Event Detected Interrupt Disable
OVR0Channel Overrun Interrupt Disable

CHANNEL29.CHINTENSETChannel n Interrupt Enable Set

Address
0x4486010D
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5–
  4. 4–
  5. 3–
  6. 2–
  7. 1EVD
  8. 0OVR
2 fields
FieldBitsWhat it does
EVD1Channel Event Detected Interrupt Enable
OVR0Channel Overrun Interrupt Enable

CHANNEL29.CHINTFLAGChannel n Interrupt Flag Status and Clear

Address
0x4486010E
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5–
  4. 4–
  5. 3–
  6. 2–
  7. 1EVD
  8. 0OVR
2 fields
FieldBitsWhat it does
EVD1Channel Event Detected
OVR0Channel Overrun

CHANNEL29.CHSTATUSChannel n Status

Address
0x4486010F
Reset
0x01
Access
read only
  1. 7–
  2. 6–
  3. 5–
  4. 4–
  5. 3–
  6. 2–
  7. 1BUSYCH
  8. 0RDYUSR
2 fields
FieldBitsWhat it does
BUSYCH1Busy Channel
RDYUSR0Ready User

CHANNEL30.CHANNELChannel n Control

Address
0x44860110
Reset
0x00008000
Access
read/write
Size
32-bit
5 fields
FieldBitsWhat it does
ONDEMAND15Generic Clock On Demand
RUNSTDBY14Run in standby
EDGSEL11:10Edge Detection Selection
  • 0 No event output when using the resynchronized or synchronous path
  • 1 Event detection only on the rising edge of the signal from the event generator when using the resynchronized or synchronous path
  • 2 Event detection only on the falling edge of the signal from the event generator when using the resynchronized or synchronous path
  • 3 Event detection on rising and falling edges of the signal from the event generator when using the resynchronized or synchronous path
PATH9:8Path Selection
  • 0 Asynchronous path
  • 1 Resynchronized path
EVGEN7:0Event Generator Selection

CHANNEL30.CHINTENCLRChannel n Interrupt Enable Clear

Address
0x44860114
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5–
  4. 4–
  5. 3–
  6. 2–
  7. 1EVD
  8. 0OVR
2 fields
FieldBitsWhat it does
EVD1Channel Event Detected Interrupt Disable
OVR0Channel Overrun Interrupt Disable

CHANNEL30.CHINTENSETChannel n Interrupt Enable Set

Address
0x44860115
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5–
  4. 4–
  5. 3–
  6. 2–
  7. 1EVD
  8. 0OVR
2 fields
FieldBitsWhat it does
EVD1Channel Event Detected Interrupt Enable
OVR0Channel Overrun Interrupt Enable

CHANNEL30.CHINTFLAGChannel n Interrupt Flag Status and Clear

Address
0x44860116
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5–
  4. 4–
  5. 3–
  6. 2–
  7. 1EVD
  8. 0OVR
2 fields
FieldBitsWhat it does
EVD1Channel Event Detected
OVR0Channel Overrun

CHANNEL30.CHSTATUSChannel n Status

Address
0x44860117
Reset
0x01
Access
read only
  1. 7–
  2. 6–
  3. 5–
  4. 4–
  5. 3–
  6. 2–
  7. 1BUSYCH
  8. 0RDYUSR
2 fields
FieldBitsWhat it does
BUSYCH1Busy Channel
RDYUSR0Ready User

CHANNEL31.CHANNELChannel n Control

Address
0x44860118
Reset
0x00008000
Access
read/write
Size
32-bit
5 fields
FieldBitsWhat it does
ONDEMAND15Generic Clock On Demand
RUNSTDBY14Run in standby
EDGSEL11:10Edge Detection Selection
  • 0 No event output when using the resynchronized or synchronous path
  • 1 Event detection only on the rising edge of the signal from the event generator when using the resynchronized or synchronous path
  • 2 Event detection only on the falling edge of the signal from the event generator when using the resynchronized or synchronous path
  • 3 Event detection on rising and falling edges of the signal from the event generator when using the resynchronized or synchronous path
PATH9:8Path Selection
  • 0 Asynchronous path
  • 1 Resynchronized path
EVGEN7:0Event Generator Selection

CHANNEL31.CHINTENCLRChannel n Interrupt Enable Clear

Address
0x4486011C
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5–
  4. 4–
  5. 3–
  6. 2–
  7. 1EVD
  8. 0OVR
2 fields
FieldBitsWhat it does
EVD1Channel Event Detected Interrupt Disable
OVR0Channel Overrun Interrupt Disable

CHANNEL31.CHINTENSETChannel n Interrupt Enable Set

Address
0x4486011D
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5–
  4. 4–
  5. 3–
  6. 2–
  7. 1EVD
  8. 0OVR
2 fields
FieldBitsWhat it does
EVD1Channel Event Detected Interrupt Enable
OVR0Channel Overrun Interrupt Enable

CHANNEL31.CHINTFLAGChannel n Interrupt Flag Status and Clear

Address
0x4486011E
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5–
  4. 4–
  5. 3–
  6. 2–
  7. 1EVD
  8. 0OVR
2 fields
FieldBitsWhat it does
EVD1Channel Event Detected
OVR0Channel Overrun

CHANNEL31.CHSTATUSChannel n Status

Address
0x4486011F
Reset
0x01
Access
read only
  1. 7–
  2. 6–
  3. 5–
  4. 4–
  5. 3–
  6. 2–
  7. 1BUSYCH
  8. 0RDYUSR
2 fields
FieldBitsWhat it does
BUSYCH1Busy Channel
RDYUSR0Ready User

USER0User Multiplexer n

Address
0x44860120
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5CHANNEL5
  4. 4CHANNEL4
  5. 3CHANNEL3
  6. 2CHANNEL2
  7. 1CHANNEL1
  8. 0CHANNEL0
1 field
FieldBitsWhat it does
CHANNEL5:0Channel Event Selection

USER1User Multiplexer n

Address
0x44860121
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5CHANNEL5
  4. 4CHANNEL4
  5. 3CHANNEL3
  6. 2CHANNEL2
  7. 1CHANNEL1
  8. 0CHANNEL0
1 field
FieldBitsWhat it does
CHANNEL5:0Channel Event Selection

USER2User Multiplexer n

Address
0x44860122
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5CHANNEL5
  4. 4CHANNEL4
  5. 3CHANNEL3
  6. 2CHANNEL2
  7. 1CHANNEL1
  8. 0CHANNEL0
1 field
FieldBitsWhat it does
CHANNEL5:0Channel Event Selection

USER3User Multiplexer n

Address
0x44860123
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5CHANNEL5
  4. 4CHANNEL4
  5. 3CHANNEL3
  6. 2CHANNEL2
  7. 1CHANNEL1
  8. 0CHANNEL0
1 field
FieldBitsWhat it does
CHANNEL5:0Channel Event Selection

USER4User Multiplexer n

Address
0x44860124
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5CHANNEL5
  4. 4CHANNEL4
  5. 3CHANNEL3
  6. 2CHANNEL2
  7. 1CHANNEL1
  8. 0CHANNEL0
1 field
FieldBitsWhat it does
CHANNEL5:0Channel Event Selection

USER5User Multiplexer n

Address
0x44860125
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5CHANNEL5
  4. 4CHANNEL4
  5. 3CHANNEL3
  6. 2CHANNEL2
  7. 1CHANNEL1
  8. 0CHANNEL0
1 field
FieldBitsWhat it does
CHANNEL5:0Channel Event Selection

USER6User Multiplexer n

Address
0x44860126
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5CHANNEL5
  4. 4CHANNEL4
  5. 3CHANNEL3
  6. 2CHANNEL2
  7. 1CHANNEL1
  8. 0CHANNEL0
1 field
FieldBitsWhat it does
CHANNEL5:0Channel Event Selection

USER7User Multiplexer n

Address
0x44860127
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5CHANNEL5
  4. 4CHANNEL4
  5. 3CHANNEL3
  6. 2CHANNEL2
  7. 1CHANNEL1
  8. 0CHANNEL0
1 field
FieldBitsWhat it does
CHANNEL5:0Channel Event Selection

USER8User Multiplexer n

Address
0x44860128
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5CHANNEL5
  4. 4CHANNEL4
  5. 3CHANNEL3
  6. 2CHANNEL2
  7. 1CHANNEL1
  8. 0CHANNEL0
1 field
FieldBitsWhat it does
CHANNEL5:0Channel Event Selection

USER9User Multiplexer n

Address
0x44860129
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5CHANNEL5
  4. 4CHANNEL4
  5. 3CHANNEL3
  6. 2CHANNEL2
  7. 1CHANNEL1
  8. 0CHANNEL0
1 field
FieldBitsWhat it does
CHANNEL5:0Channel Event Selection

USER10User Multiplexer n

Address
0x4486012A
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5CHANNEL5
  4. 4CHANNEL4
  5. 3CHANNEL3
  6. 2CHANNEL2
  7. 1CHANNEL1
  8. 0CHANNEL0
1 field
FieldBitsWhat it does
CHANNEL5:0Channel Event Selection

USER11User Multiplexer n

Address
0x4486012B
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5CHANNEL5
  4. 4CHANNEL4
  5. 3CHANNEL3
  6. 2CHANNEL2
  7. 1CHANNEL1
  8. 0CHANNEL0
1 field
FieldBitsWhat it does
CHANNEL5:0Channel Event Selection

USER12User Multiplexer n

Address
0x4486012C
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5CHANNEL5
  4. 4CHANNEL4
  5. 3CHANNEL3
  6. 2CHANNEL2
  7. 1CHANNEL1
  8. 0CHANNEL0
1 field
FieldBitsWhat it does
CHANNEL5:0Channel Event Selection

USER13User Multiplexer n

Address
0x4486012D
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5CHANNEL5
  4. 4CHANNEL4
  5. 3CHANNEL3
  6. 2CHANNEL2
  7. 1CHANNEL1
  8. 0CHANNEL0
1 field
FieldBitsWhat it does
CHANNEL5:0Channel Event Selection

USER14User Multiplexer n

Address
0x4486012E
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5CHANNEL5
  4. 4CHANNEL4
  5. 3CHANNEL3
  6. 2CHANNEL2
  7. 1CHANNEL1
  8. 0CHANNEL0
1 field
FieldBitsWhat it does
CHANNEL5:0Channel Event Selection

USER15User Multiplexer n

Address
0x4486012F
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5CHANNEL5
  4. 4CHANNEL4
  5. 3CHANNEL3
  6. 2CHANNEL2
  7. 1CHANNEL1
  8. 0CHANNEL0
1 field
FieldBitsWhat it does
CHANNEL5:0Channel Event Selection

USER16User Multiplexer n

Address
0x44860130
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5CHANNEL5
  4. 4CHANNEL4
  5. 3CHANNEL3
  6. 2CHANNEL2
  7. 1CHANNEL1
  8. 0CHANNEL0
1 field
FieldBitsWhat it does
CHANNEL5:0Channel Event Selection

USER17User Multiplexer n

Address
0x44860131
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5CHANNEL5
  4. 4CHANNEL4
  5. 3CHANNEL3
  6. 2CHANNEL2
  7. 1CHANNEL1
  8. 0CHANNEL0
1 field
FieldBitsWhat it does
CHANNEL5:0Channel Event Selection

USER18User Multiplexer n

Address
0x44860132
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5CHANNEL5
  4. 4CHANNEL4
  5. 3CHANNEL3
  6. 2CHANNEL2
  7. 1CHANNEL1
  8. 0CHANNEL0
1 field
FieldBitsWhat it does
CHANNEL5:0Channel Event Selection

USER19User Multiplexer n

Address
0x44860133
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5CHANNEL5
  4. 4CHANNEL4
  5. 3CHANNEL3
  6. 2CHANNEL2
  7. 1CHANNEL1
  8. 0CHANNEL0
1 field
FieldBitsWhat it does
CHANNEL5:0Channel Event Selection

USER20User Multiplexer n

Address
0x44860134
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5CHANNEL5
  4. 4CHANNEL4
  5. 3CHANNEL3
  6. 2CHANNEL2
  7. 1CHANNEL1
  8. 0CHANNEL0
1 field
FieldBitsWhat it does
CHANNEL5:0Channel Event Selection

USER21User Multiplexer n

Address
0x44860135
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5CHANNEL5
  4. 4CHANNEL4
  5. 3CHANNEL3
  6. 2CHANNEL2
  7. 1CHANNEL1
  8. 0CHANNEL0
1 field
FieldBitsWhat it does
CHANNEL5:0Channel Event Selection

USER22User Multiplexer n

Address
0x44860136
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5CHANNEL5
  4. 4CHANNEL4
  5. 3CHANNEL3
  6. 2CHANNEL2
  7. 1CHANNEL1
  8. 0CHANNEL0
1 field
FieldBitsWhat it does
CHANNEL5:0Channel Event Selection

USER23User Multiplexer n

Address
0x44860137
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5CHANNEL5
  4. 4CHANNEL4
  5. 3CHANNEL3
  6. 2CHANNEL2
  7. 1CHANNEL1
  8. 0CHANNEL0
1 field
FieldBitsWhat it does
CHANNEL5:0Channel Event Selection

USER24User Multiplexer n

Address
0x44860138
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5CHANNEL5
  4. 4CHANNEL4
  5. 3CHANNEL3
  6. 2CHANNEL2
  7. 1CHANNEL1
  8. 0CHANNEL0
1 field
FieldBitsWhat it does
CHANNEL5:0Channel Event Selection

USER25User Multiplexer n

Address
0x44860139
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5CHANNEL5
  4. 4CHANNEL4
  5. 3CHANNEL3
  6. 2CHANNEL2
  7. 1CHANNEL1
  8. 0CHANNEL0
1 field
FieldBitsWhat it does
CHANNEL5:0Channel Event Selection

USER26User Multiplexer n

Address
0x4486013A
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5CHANNEL5
  4. 4CHANNEL4
  5. 3CHANNEL3
  6. 2CHANNEL2
  7. 1CHANNEL1
  8. 0CHANNEL0
1 field
FieldBitsWhat it does
CHANNEL5:0Channel Event Selection

USER27User Multiplexer n

Address
0x4486013B
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5CHANNEL5
  4. 4CHANNEL4
  5. 3CHANNEL3
  6. 2CHANNEL2
  7. 1CHANNEL1
  8. 0CHANNEL0
1 field
FieldBitsWhat it does
CHANNEL5:0Channel Event Selection

USER28User Multiplexer n

Address
0x4486013C
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5CHANNEL5
  4. 4CHANNEL4
  5. 3CHANNEL3
  6. 2CHANNEL2
  7. 1CHANNEL1
  8. 0CHANNEL0
1 field
FieldBitsWhat it does
CHANNEL5:0Channel Event Selection

USER29User Multiplexer n

Address
0x4486013D
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5CHANNEL5
  4. 4CHANNEL4
  5. 3CHANNEL3
  6. 2CHANNEL2
  7. 1CHANNEL1
  8. 0CHANNEL0
1 field
FieldBitsWhat it does
CHANNEL5:0Channel Event Selection

USER30User Multiplexer n

Address
0x4486013E
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5CHANNEL5
  4. 4CHANNEL4
  5. 3CHANNEL3
  6. 2CHANNEL2
  7. 1CHANNEL1
  8. 0CHANNEL0
1 field
FieldBitsWhat it does
CHANNEL5:0Channel Event Selection

USER31User Multiplexer n

Address
0x4486013F
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5CHANNEL5
  4. 4CHANNEL4
  5. 3CHANNEL3
  6. 2CHANNEL2
  7. 1CHANNEL1
  8. 0CHANNEL0
1 field
FieldBitsWhat it does
CHANNEL5:0Channel Event Selection

USER32User Multiplexer n

Address
0x44860140
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5CHANNEL5
  4. 4CHANNEL4
  5. 3CHANNEL3
  6. 2CHANNEL2
  7. 1CHANNEL1
  8. 0CHANNEL0
1 field
FieldBitsWhat it does
CHANNEL5:0Channel Event Selection

USER33User Multiplexer n

Address
0x44860141
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5CHANNEL5
  4. 4CHANNEL4
  5. 3CHANNEL3
  6. 2CHANNEL2
  7. 1CHANNEL1
  8. 0CHANNEL0
1 field
FieldBitsWhat it does
CHANNEL5:0Channel Event Selection

USER34User Multiplexer n

Address
0x44860142
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5CHANNEL5
  4. 4CHANNEL4
  5. 3CHANNEL3
  6. 2CHANNEL2
  7. 1CHANNEL1
  8. 0CHANNEL0
1 field
FieldBitsWhat it does
CHANNEL5:0Channel Event Selection

USER35User Multiplexer n

Address
0x44860143
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5CHANNEL5
  4. 4CHANNEL4
  5. 3CHANNEL3
  6. 2CHANNEL2
  7. 1CHANNEL1
  8. 0CHANNEL0
1 field
FieldBitsWhat it does
CHANNEL5:0Channel Event Selection

USER36User Multiplexer n

Address
0x44860144
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5CHANNEL5
  4. 4CHANNEL4
  5. 3CHANNEL3
  6. 2CHANNEL2
  7. 1CHANNEL1
  8. 0CHANNEL0
1 field
FieldBitsWhat it does
CHANNEL5:0Channel Event Selection

USER37User Multiplexer n

Address
0x44860145
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5CHANNEL5
  4. 4CHANNEL4
  5. 3CHANNEL3
  6. 2CHANNEL2
  7. 1CHANNEL1
  8. 0CHANNEL0
1 field
FieldBitsWhat it does
CHANNEL5:0Channel Event Selection

USER38User Multiplexer n

Address
0x44860146
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5CHANNEL5
  4. 4CHANNEL4
  5. 3CHANNEL3
  6. 2CHANNEL2
  7. 1CHANNEL1
  8. 0CHANNEL0
1 field
FieldBitsWhat it does
CHANNEL5:0Channel Event Selection

USER39User Multiplexer n

Address
0x44860147
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5CHANNEL5
  4. 4CHANNEL4
  5. 3CHANNEL3
  6. 2CHANNEL2
  7. 1CHANNEL1
  8. 0CHANNEL0
1 field
FieldBitsWhat it does
CHANNEL5:0Channel Event Selection

USER40User Multiplexer n

Address
0x44860148
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5CHANNEL5
  4. 4CHANNEL4
  5. 3CHANNEL3
  6. 2CHANNEL2
  7. 1CHANNEL1
  8. 0CHANNEL0
1 field
FieldBitsWhat it does
CHANNEL5:0Channel Event Selection

USER41User Multiplexer n

Address
0x44860149
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5CHANNEL5
  4. 4CHANNEL4
  5. 3CHANNEL3
  6. 2CHANNEL2
  7. 1CHANNEL1
  8. 0CHANNEL0
1 field
FieldBitsWhat it does
CHANNEL5:0Channel Event Selection

USER42User Multiplexer n

Address
0x4486014A
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5CHANNEL5
  4. 4CHANNEL4
  5. 3CHANNEL3
  6. 2CHANNEL2
  7. 1CHANNEL1
  8. 0CHANNEL0
1 field
FieldBitsWhat it does
CHANNEL5:0Channel Event Selection

USER43User Multiplexer n

Address
0x4486014B
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5CHANNEL5
  4. 4CHANNEL4
  5. 3CHANNEL3
  6. 2CHANNEL2
  7. 1CHANNEL1
  8. 0CHANNEL0
1 field
FieldBitsWhat it does
CHANNEL5:0Channel Event Selection

USER44User Multiplexer n

Address
0x4486014C
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5CHANNEL5
  4. 4CHANNEL4
  5. 3CHANNEL3
  6. 2CHANNEL2
  7. 1CHANNEL1
  8. 0CHANNEL0
1 field
FieldBitsWhat it does
CHANNEL5:0Channel Event Selection

USER45User Multiplexer n

Address
0x4486014D
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5CHANNEL5
  4. 4CHANNEL4
  5. 3CHANNEL3
  6. 2CHANNEL2
  7. 1CHANNEL1
  8. 0CHANNEL0
1 field
FieldBitsWhat it does
CHANNEL5:0Channel Event Selection

USER46User Multiplexer n

Address
0x4486014E
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5CHANNEL5
  4. 4CHANNEL4
  5. 3CHANNEL3
  6. 2CHANNEL2
  7. 1CHANNEL1
  8. 0CHANNEL0
1 field
FieldBitsWhat it does
CHANNEL5:0Channel Event Selection

USER47User Multiplexer n

Address
0x4486014F
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5CHANNEL5
  4. 4CHANNEL4
  5. 3CHANNEL3
  6. 2CHANNEL2
  7. 1CHANNEL1
  8. 0CHANNEL0
1 field
FieldBitsWhat it does
CHANNEL5:0Channel Event Selection

USER48User Multiplexer n

Address
0x44860150
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5CHANNEL5
  4. 4CHANNEL4
  5. 3CHANNEL3
  6. 2CHANNEL2
  7. 1CHANNEL1
  8. 0CHANNEL0
1 field
FieldBitsWhat it does
CHANNEL5:0Channel Event Selection

USER49User Multiplexer n

Address
0x44860151
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5CHANNEL5
  4. 4CHANNEL4
  5. 3CHANNEL3
  6. 2CHANNEL2
  7. 1CHANNEL1
  8. 0CHANNEL0
1 field
FieldBitsWhat it does
CHANNEL5:0Channel Event Selection

USER50User Multiplexer n

Address
0x44860152
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5CHANNEL5
  4. 4CHANNEL4
  5. 3CHANNEL3
  6. 2CHANNEL2
  7. 1CHANNEL1
  8. 0CHANNEL0
1 field
FieldBitsWhat it does
CHANNEL5:0Channel Event Selection

USER51User Multiplexer n

Address
0x44860153
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5CHANNEL5
  4. 4CHANNEL4
  5. 3CHANNEL3
  6. 2CHANNEL2
  7. 1CHANNEL1
  8. 0CHANNEL0
1 field
FieldBitsWhat it does
CHANNEL5:0Channel Event Selection

USER52User Multiplexer n

Address
0x44860154
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5CHANNEL5
  4. 4CHANNEL4
  5. 3CHANNEL3
  6. 2CHANNEL2
  7. 1CHANNEL1
  8. 0CHANNEL0
1 field
FieldBitsWhat it does
CHANNEL5:0Channel Event Selection

USER53User Multiplexer n

Address
0x44860155
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5CHANNEL5
  4. 4CHANNEL4
  5. 3CHANNEL3
  6. 2CHANNEL2
  7. 1CHANNEL1
  8. 0CHANNEL0
1 field
FieldBitsWhat it does
CHANNEL5:0Channel Event Selection

USER54User Multiplexer n

Address
0x44860156
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5CHANNEL5
  4. 4CHANNEL4
  5. 3CHANNEL3
  6. 2CHANNEL2
  7. 1CHANNEL1
  8. 0CHANNEL0
1 field
FieldBitsWhat it does
CHANNEL5:0Channel Event Selection

USER55User Multiplexer n

Address
0x44860157
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5CHANNEL5
  4. 4CHANNEL4
  5. 3CHANNEL3
  6. 2CHANNEL2
  7. 1CHANNEL1
  8. 0CHANNEL0
1 field
FieldBitsWhat it does
CHANNEL5:0Channel Event Selection

USER56User Multiplexer n

Address
0x44860158
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5CHANNEL5
  4. 4CHANNEL4
  5. 3CHANNEL3
  6. 2CHANNEL2
  7. 1CHANNEL1
  8. 0CHANNEL0
1 field
FieldBitsWhat it does
CHANNEL5:0Channel Event Selection

USER57User Multiplexer n

Address
0x44860159
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5CHANNEL5
  4. 4CHANNEL4
  5. 3CHANNEL3
  6. 2CHANNEL2
  7. 1CHANNEL1
  8. 0CHANNEL0
1 field
FieldBitsWhat it does
CHANNEL5:0Channel Event Selection

USER58User Multiplexer n

Address
0x4486015A
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5CHANNEL5
  4. 4CHANNEL4
  5. 3CHANNEL3
  6. 2CHANNEL2
  7. 1CHANNEL1
  8. 0CHANNEL0
1 field
FieldBitsWhat it does
CHANNEL5:0Channel Event Selection

USER59User Multiplexer n

Address
0x4486015B
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5CHANNEL5
  4. 4CHANNEL4
  5. 3CHANNEL3
  6. 2CHANNEL2
  7. 1CHANNEL1
  8. 0CHANNEL0
1 field
FieldBitsWhat it does
CHANNEL5:0Channel Event Selection

USER60User Multiplexer n

Address
0x4486015C
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5CHANNEL5
  4. 4CHANNEL4
  5. 3CHANNEL3
  6. 2CHANNEL2
  7. 1CHANNEL1
  8. 0CHANNEL0
1 field
FieldBitsWhat it does
CHANNEL5:0Channel Event Selection

USER61User Multiplexer n

Address
0x4486015D
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5CHANNEL5
  4. 4CHANNEL4
  5. 3CHANNEL3
  6. 2CHANNEL2
  7. 1CHANNEL1
  8. 0CHANNEL0
1 field
FieldBitsWhat it does
CHANNEL5:0Channel Event Selection

USER62User Multiplexer n

Address
0x4486015E
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5CHANNEL5
  4. 4CHANNEL4
  5. 3CHANNEL3
  6. 2CHANNEL2
  7. 1CHANNEL1
  8. 0CHANNEL0
1 field
FieldBitsWhat it does
CHANNEL5:0Channel Event Selection

USER63User Multiplexer n

Address
0x4486015F
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5CHANNEL5
  4. 4CHANNEL4
  5. 3CHANNEL3
  6. 2CHANNEL2
  7. 1CHANNEL1
  8. 0CHANNEL0
1 field
FieldBitsWhat it does
CHANNEL5:0Channel Event Selection

USER64User Multiplexer n

Address
0x44860160
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5CHANNEL5
  4. 4CHANNEL4
  5. 3CHANNEL3
  6. 2CHANNEL2
  7. 1CHANNEL1
  8. 0CHANNEL0
1 field
FieldBitsWhat it does
CHANNEL5:0Channel Event Selection

USER65User Multiplexer n

Address
0x44860161
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5CHANNEL5
  4. 4CHANNEL4
  5. 3CHANNEL3
  6. 2CHANNEL2
  7. 1CHANNEL1
  8. 0CHANNEL0
1 field
FieldBitsWhat it does
CHANNEL5:0Channel Event Selection

USER66User Multiplexer n

Address
0x44860162
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5CHANNEL5
  4. 4CHANNEL4
  5. 3CHANNEL3
  6. 2CHANNEL2
  7. 1CHANNEL1
  8. 0CHANNEL0
1 field
FieldBitsWhat it does
CHANNEL5:0Channel Event Selection

USER67User Multiplexer n

Address
0x44860163
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5CHANNEL5
  4. 4CHANNEL4
  5. 3CHANNEL3
  6. 2CHANNEL2
  7. 1CHANNEL1
  8. 0CHANNEL0
1 field
FieldBitsWhat it does
CHANNEL5:0Channel Event Selection

USER68User Multiplexer n

Address
0x44860164
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5CHANNEL5
  4. 4CHANNEL4
  5. 3CHANNEL3
  6. 2CHANNEL2
  7. 1CHANNEL1
  8. 0CHANNEL0
1 field
FieldBitsWhat it does
CHANNEL5:0Channel Event Selection

USER69User Multiplexer n

Address
0x44860165
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5CHANNEL5
  4. 4CHANNEL4
  5. 3CHANNEL3
  6. 2CHANNEL2
  7. 1CHANNEL1
  8. 0CHANNEL0
1 field
FieldBitsWhat it does
CHANNEL5:0Channel Event Selection

USER70User Multiplexer n

Address
0x44860166
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5CHANNEL5
  4. 4CHANNEL4
  5. 3CHANNEL3
  6. 2CHANNEL2
  7. 1CHANNEL1
  8. 0CHANNEL0
1 field
FieldBitsWhat it does
CHANNEL5:0Channel Event Selection

USER71User Multiplexer n

Address
0x44860167
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5CHANNEL5
  4. 4CHANNEL4
  5. 3CHANNEL3
  6. 2CHANNEL2
  7. 1CHANNEL1
  8. 0CHANNEL0
1 field
FieldBitsWhat it does
CHANNEL5:0Channel Event Selection

USER72User Multiplexer n

Address
0x44860168
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5CHANNEL5
  4. 4CHANNEL4
  5. 3CHANNEL3
  6. 2CHANNEL2
  7. 1CHANNEL1
  8. 0CHANNEL0
1 field
FieldBitsWhat it does
CHANNEL5:0Channel Event Selection

USER73User Multiplexer n

Address
0x44860169
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5CHANNEL5
  4. 4CHANNEL4
  5. 3CHANNEL3
  6. 2CHANNEL2
  7. 1CHANNEL1
  8. 0CHANNEL0
1 field
FieldBitsWhat it does
CHANNEL5:0Channel Event Selection

USER74User Multiplexer n

Address
0x4486016A
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5CHANNEL5
  4. 4CHANNEL4
  5. 3CHANNEL3
  6. 2CHANNEL2
  7. 1CHANNEL1
  8. 0CHANNEL0
1 field
FieldBitsWhat it does
CHANNEL5:0Channel Event Selection

USER75User Multiplexer n

Address
0x4486016B
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5CHANNEL5
  4. 4CHANNEL4
  5. 3CHANNEL3
  6. 2CHANNEL2
  7. 1CHANNEL1
  8. 0CHANNEL0
1 field
FieldBitsWhat it does
CHANNEL5:0Channel Event Selection

USER76User Multiplexer n

Address
0x4486016C
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5CHANNEL5
  4. 4CHANNEL4
  5. 3CHANNEL3
  6. 2CHANNEL2
  7. 1CHANNEL1
  8. 0CHANNEL0
1 field
FieldBitsWhat it does
CHANNEL5:0Channel Event Selection

USER77User Multiplexer n

Address
0x4486016D
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5CHANNEL5
  4. 4CHANNEL4
  5. 3CHANNEL3
  6. 2CHANNEL2
  7. 1CHANNEL1
  8. 0CHANNEL0
1 field
FieldBitsWhat it does
CHANNEL5:0Channel Event Selection

USER78User Multiplexer n

Address
0x4486016E
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5CHANNEL5
  4. 4CHANNEL4
  5. 3CHANNEL3
  6. 2CHANNEL2
  7. 1CHANNEL1
  8. 0CHANNEL0
1 field
FieldBitsWhat it does
CHANNEL5:0Channel Event Selection

USER79User Multiplexer n

Address
0x4486016F
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5CHANNEL5
  4. 4CHANNEL4
  5. 3CHANNEL3
  6. 2CHANNEL2
  7. 1CHANNEL1
  8. 0CHANNEL0
1 field
FieldBitsWhat it does
CHANNEL5:0Channel Event Selection

USER80User Multiplexer n

Address
0x44860170
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5CHANNEL5
  4. 4CHANNEL4
  5. 3CHANNEL3
  6. 2CHANNEL2
  7. 1CHANNEL1
  8. 0CHANNEL0
1 field
FieldBitsWhat it does
CHANNEL5:0Channel Event Selection

USER81User Multiplexer n

Address
0x44860171
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5CHANNEL5
  4. 4CHANNEL4
  5. 3CHANNEL3
  6. 2CHANNEL2
  7. 1CHANNEL1
  8. 0CHANNEL0
1 field
FieldBitsWhat it does
CHANNEL5:0Channel Event Selection

USER82User Multiplexer n

Address
0x44860172
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5CHANNEL5
  4. 4CHANNEL4
  5. 3CHANNEL3
  6. 2CHANNEL2
  7. 1CHANNEL1
  8. 0CHANNEL0
1 field
FieldBitsWhat it does
CHANNEL5:0Channel Event Selection

USER83User Multiplexer n

Address
0x44860173
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5CHANNEL5
  4. 4CHANNEL4
  5. 3CHANNEL3
  6. 2CHANNEL2
  7. 1CHANNEL1
  8. 0CHANNEL0
1 field
FieldBitsWhat it does
CHANNEL5:0Channel Event Selection

USER84User Multiplexer n

Address
0x44860174
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5CHANNEL5
  4. 4CHANNEL4
  5. 3CHANNEL3
  6. 2CHANNEL2
  7. 1CHANNEL1
  8. 0CHANNEL0
1 field
FieldBitsWhat it does
CHANNEL5:0Channel Event Selection

USER85User Multiplexer n

Address
0x44860175
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5CHANNEL5
  4. 4CHANNEL4
  5. 3CHANNEL3
  6. 2CHANNEL2
  7. 1CHANNEL1
  8. 0CHANNEL0
1 field
FieldBitsWhat it does
CHANNEL5:0Channel Event Selection

USER86User Multiplexer n

Address
0x44860176
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5CHANNEL5
  4. 4CHANNEL4
  5. 3CHANNEL3
  6. 2CHANNEL2
  7. 1CHANNEL1
  8. 0CHANNEL0
1 field
FieldBitsWhat it does
CHANNEL5:0Channel Event Selection

USER87User Multiplexer n

Address
0x44860177
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5CHANNEL5
  4. 4CHANNEL4
  5. 3CHANNEL3
  6. 2CHANNEL2
  7. 1CHANNEL1
  8. 0CHANNEL0
1 field
FieldBitsWhat it does
CHANNEL5:0Channel Event Selection

USER88User Multiplexer n

Address
0x44860178
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5CHANNEL5
  4. 4CHANNEL4
  5. 3CHANNEL3
  6. 2CHANNEL2
  7. 1CHANNEL1
  8. 0CHANNEL0
1 field
FieldBitsWhat it does
CHANNEL5:0Channel Event Selection

USER89User Multiplexer n

Address
0x44860179
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5CHANNEL5
  4. 4CHANNEL4
  5. 3CHANNEL3
  6. 2CHANNEL2
  7. 1CHANNEL1
  8. 0CHANNEL0
1 field
FieldBitsWhat it does
CHANNEL5:0Channel Event Selection

USER90User Multiplexer n

Address
0x4486017A
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5CHANNEL5
  4. 4CHANNEL4
  5. 3CHANNEL3
  6. 2CHANNEL2
  7. 1CHANNEL1
  8. 0CHANNEL0
1 field
FieldBitsWhat it does
CHANNEL5:0Channel Event Selection

USER91User Multiplexer n

Address
0x4486017B
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5CHANNEL5
  4. 4CHANNEL4
  5. 3CHANNEL3
  6. 2CHANNEL2
  7. 1CHANNEL1
  8. 0CHANNEL0
1 field
FieldBitsWhat it does
CHANNEL5:0Channel Event Selection

USER92User Multiplexer n

Address
0x4486017C
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5CHANNEL5
  4. 4CHANNEL4
  5. 3CHANNEL3
  6. 2CHANNEL2
  7. 1CHANNEL1
  8. 0CHANNEL0
1 field
FieldBitsWhat it does
CHANNEL5:0Channel Event Selection

USER93User Multiplexer n

Address
0x4486017D
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5CHANNEL5
  4. 4CHANNEL4
  5. 3CHANNEL3
  6. 2CHANNEL2
  7. 1CHANNEL1
  8. 0CHANNEL0
1 field
FieldBitsWhat it does
CHANNEL5:0Channel Event Selection

USER94User Multiplexer n

Address
0x4486017E
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5CHANNEL5
  4. 4CHANNEL4
  5. 3CHANNEL3
  6. 2CHANNEL2
  7. 1CHANNEL1
  8. 0CHANNEL0
1 field
FieldBitsWhat it does
CHANNEL5:0Channel Event Selection

USER95User Multiplexer n

Address
0x4486017F
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5CHANNEL5
  4. 4CHANNEL4
  5. 3CHANNEL3
  6. 2CHANNEL2
  7. 1CHANNEL1
  8. 0CHANNEL0
1 field
FieldBitsWhat it does
CHANNEL5:0Channel Event Selection

USER96User Multiplexer n

Address
0x44860180
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5CHANNEL5
  4. 4CHANNEL4
  5. 3CHANNEL3
  6. 2CHANNEL2
  7. 1CHANNEL1
  8. 0CHANNEL0
1 field
FieldBitsWhat it does
CHANNEL5:0Channel Event Selection

USER97User Multiplexer n

Address
0x44860181
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5CHANNEL5
  4. 4CHANNEL4
  5. 3CHANNEL3
  6. 2CHANNEL2
  7. 1CHANNEL1
  8. 0CHANNEL0
1 field
FieldBitsWhat it does
CHANNEL5:0Channel Event Selection

USER98User Multiplexer n

Address
0x44860182
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5CHANNEL5
  4. 4CHANNEL4
  5. 3CHANNEL3
  6. 2CHANNEL2
  7. 1CHANNEL1
  8. 0CHANNEL0
1 field
FieldBitsWhat it does
CHANNEL5:0Channel Event Selection

USER99User Multiplexer n

Address
0x44860183
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5CHANNEL5
  4. 4CHANNEL4
  5. 3CHANNEL3
  6. 2CHANNEL2
  7. 1CHANNEL1
  8. 0CHANNEL0
1 field
FieldBitsWhat it does
CHANNEL5:0Channel Event Selection

USER100User Multiplexer n

Address
0x44860184
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5CHANNEL5
  4. 4CHANNEL4
  5. 3CHANNEL3
  6. 2CHANNEL2
  7. 1CHANNEL1
  8. 0CHANNEL0
1 field
FieldBitsWhat it does
CHANNEL5:0Channel Event Selection

USER101User Multiplexer n

Address
0x44860185
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5CHANNEL5
  4. 4CHANNEL4
  5. 3CHANNEL3
  6. 2CHANNEL2
  7. 1CHANNEL1
  8. 0CHANNEL0
1 field
FieldBitsWhat it does
CHANNEL5:0Channel Event Selection

USER102User Multiplexer n

Address
0x44860186
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5CHANNEL5
  4. 4CHANNEL4
  5. 3CHANNEL3
  6. 2CHANNEL2
  7. 1CHANNEL1
  8. 0CHANNEL0
1 field
FieldBitsWhat it does
CHANNEL5:0Channel Event Selection

USER103User Multiplexer n

Address
0x44860187
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5CHANNEL5
  4. 4CHANNEL4
  5. 3CHANNEL3
  6. 2CHANNEL2
  7. 1CHANNEL1
  8. 0CHANNEL0
1 field
FieldBitsWhat it does
CHANNEL5:0Channel Event Selection

USER104User Multiplexer n

Address
0x44860188
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5CHANNEL5
  4. 4CHANNEL4
  5. 3CHANNEL3
  6. 2CHANNEL2
  7. 1CHANNEL1
  8. 0CHANNEL0
1 field
FieldBitsWhat it does
CHANNEL5:0Channel Event Selection

USER105User Multiplexer n

Address
0x44860189
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5CHANNEL5
  4. 4CHANNEL4
  5. 3CHANNEL3
  6. 2CHANNEL2
  7. 1CHANNEL1
  8. 0CHANNEL0
1 field
FieldBitsWhat it does
CHANNEL5:0Channel Event Selection

USER106User Multiplexer n

Address
0x4486018A
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5CHANNEL5
  4. 4CHANNEL4
  5. 3CHANNEL3
  6. 2CHANNEL2
  7. 1CHANNEL1
  8. 0CHANNEL0
1 field
FieldBitsWhat it does
CHANNEL5:0Channel Event Selection

USER107User Multiplexer n

Address
0x4486018B
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5CHANNEL5
  4. 4CHANNEL4
  5. 3CHANNEL3
  6. 2CHANNEL2
  7. 1CHANNEL1
  8. 0CHANNEL0
1 field
FieldBitsWhat it does
CHANNEL5:0Channel Event Selection

USER108User Multiplexer n

Address
0x4486018C
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5CHANNEL5
  4. 4CHANNEL4
  5. 3CHANNEL3
  6. 2CHANNEL2
  7. 1CHANNEL1
  8. 0CHANNEL0
1 field
FieldBitsWhat it does
CHANNEL5:0Channel Event Selection

USER109User Multiplexer n

Address
0x4486018D
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5CHANNEL5
  4. 4CHANNEL4
  5. 3CHANNEL3
  6. 2CHANNEL2
  7. 1CHANNEL1
  8. 0CHANNEL0
1 field
FieldBitsWhat it does
CHANNEL5:0Channel Event Selection

USER110User Multiplexer n

Address
0x4486018E
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5CHANNEL5
  4. 4CHANNEL4
  5. 3CHANNEL3
  6. 2CHANNEL2
  7. 1CHANNEL1
  8. 0CHANNEL0
1 field
FieldBitsWhat it does
CHANNEL5:0Channel Event Selection

USER111User Multiplexer n

Address
0x4486018F
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5CHANNEL5
  4. 4CHANNEL4
  5. 3CHANNEL3
  6. 2CHANNEL2
  7. 1CHANNEL1
  8. 0CHANNEL0
1 field
FieldBitsWhat it does
CHANNEL5:0Channel Event Selection

USER112User Multiplexer n

Address
0x44860190
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5CHANNEL5
  4. 4CHANNEL4
  5. 3CHANNEL3
  6. 2CHANNEL2
  7. 1CHANNEL1
  8. 0CHANNEL0
1 field
FieldBitsWhat it does
CHANNEL5:0Channel Event Selection

USER113User Multiplexer n

Address
0x44860191
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5CHANNEL5
  4. 4CHANNEL4
  5. 3CHANNEL3
  6. 2CHANNEL2
  7. 1CHANNEL1
  8. 0CHANNEL0
1 field
FieldBitsWhat it does
CHANNEL5:0Channel Event Selection

USER114User Multiplexer n

Address
0x44860192
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5CHANNEL5
  4. 4CHANNEL4
  5. 3CHANNEL3
  6. 2CHANNEL2
  7. 1CHANNEL1
  8. 0CHANNEL0
1 field
FieldBitsWhat it does
CHANNEL5:0Channel Event Selection

USER115User Multiplexer n

Address
0x44860193
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5CHANNEL5
  4. 4CHANNEL4
  5. 3CHANNEL3
  6. 2CHANNEL2
  7. 1CHANNEL1
  8. 0CHANNEL0
1 field
FieldBitsWhat it does
CHANNEL5:0Channel Event Selection

USER116User Multiplexer n

Address
0x44860194
Reset
0x00
Access
read/write
  1. 7–
  2. 6–
  3. 5CHANNEL5
  4. 4CHANNEL4
  5. 3CHANNEL3
  6. 2CHANNEL2
  7. 1CHANNEL1
  8. 0CHANNEL0
1 field
FieldBitsWhat it does
CHANNEL5:0Channel Event Selection