PIC32CZ4010CA91208 SERCOM6 registers

The 73 registers of SERCOM6 (Serial Communication Interface), from 0x45806000, with their reset value and every field. The PIC32CZ4010CA91208 has 7010 registers in 78 peripherals, one page each.

SERCOM6 Serial Communication Interface

I2CM.CTRLAI2CM Control A

Address: 0x45806000
Reset: 0x00000000
Access: read/write
Size: 32-bit

15 fields

Field	Bits	What it does
LOWTOUTEN	30	SCL Low Timeout Enable
INACTOUT	29:28	Inactive Time-Out `0` Disable `1` 5-6 SCL cycle time-out `2` 10-11 SCL cycle time-out `3` 20-21-6 SCL cycle time-out
SCLSM	27	SCL Clock Stretch Mode
SPEED	25:24	Transfer Speed `0` Standard-Mode (SM) and Fast-Mode (FM) `1` Fast-Mode Plus (FM+) `2` High-Speed Mode
SEXTTOEN	23	Slave SCL Low Extend Timeout
MEXTTOEN	22	Master SCL Low Extend Timeout
SDAHOLD	21:20	SDA Hold Time `0` Disable `1` 50ns - 100ns hold time `2` 300ns - 600ns hold time `3` 400ns - 800ns hold time
SMBUSEN	17	SMBUS Input Buffer Enable
PINOUT	16	Pin Usage
SLEWRATE	11:10	Slew Rate Selection `0` Standard mode `1` Fast mode `2` Fast mode plus `3` High-speed mode
FILTSEL	9:8	Input Filter Selection `0` Disable `2` Minimum 50ns filter `3` Minimum 10ns filter
RUNSTDBY	7	Run in Standby
MODE	4:2	Operating Mode `0` USART with external clock `1` USART with internal clock `2` SPI in slave operation `3` SPI in master operation `4` I2C slave operation `5` I2C master operation
ENABLE	1	Enable
SWRST	0	Software Reset

I2CS.CTRLAI2CS Control A

Address: 0x45806000
Reset: 0x00000000
Access: read/write
Size: 32-bit

13 fields

Field	Bits	What it does
LOWTOUTEN	30	SCL Low Timeout Enable
SCLSM	27	SCL Clock Stretch Mode
SPEED	25:24	Transfer Speed `0` Standard-Mode (SM) and Fast-Mode (FM) `1` Fast-Mode Plus (FM+) `2` High-Speed Mode
SEXTTOEN	23	Slave SCL Low Extend Timeout
SDAHOLD	21:20	SDA Hold Time `0` Disable `1` 50ns - 100ns hold time `2` 300ns - 600ns hold time `3` 400ns - 800ns hold time
SMBUSEN	17	SMBUS Input Buffer Enable
PINOUT	16	Pin Usage
SLEWRATE	11:10	Slew Rate Selection `0` Standard mode `1` Fast mode `2` Fast mode plus `3` High-speed mode
FILTSEL	9:8	Input Filter Selection
RUNSTDBY	7	Run during Standby
MODE	4:2	Operating Mode `0` USART with external clock `1` USART with internal clock `2` SPI in slave operation `3` SPI in master operation `4` I2C slave operation `5` I2C master operation
ENABLE	1	Enable
SWRST	0	Software Reset

SPIM.CTRLASPIM Control A

Address: 0x45806000
Reset: 0x00000000
Access: read/write
Size: 32-bit

11 fields

Field	Bits	What it does
DORD	30	Data Order `0` MSB is transmitted first `1` LSB is transmitted first
CPOL	29	Clock Polarity `0` SCK is low when idle `1` SCK is high when idle
CPHA	28	Clock Phase `0` The data is sampled on a leading SCK edge and changed on a trailing SCK edge `1` The data is sampled on a trailing SCK edge and changed on a leading SCK edge
FORM	27:24	Frame Format `0` SPI frame `2` SPI frame with address
DIPO	21:20	Data In Pinout `0` SERCOM PAD0 is used as data input `1` SERCOM PAD1 is used as data input `2` SERCOM PAD2 is used as data input `3` SERCOM PAD3 is used as data input
DOPO	17:16	Data Out Pinout `0` DO on PAD[0], SCK on PAD[1] and SS on PAD[2] `2` DO on PAD[3], SCK on PAD[1] and SS on PAD[2]
IBON	8	Immediate Buffer Overflow Notification
RUNSTDBY	7	Run during Standby
MODE	4:2	Operating Mode `0` USART with external clock `1` USART with internal clock `2` SPI in slave operation `3` SPI in master operation `4` I2C slave operation `5` I2C master operation
ENABLE	1	Enable
SWRST	0	Software Reset

SPIS.CTRLASPIS Control A

Address: 0x45806000
Reset: 0x00000000
Access: read/write
Size: 32-bit

11 fields

Field	Bits	What it does
DORD	30	Data Order `0` MSB is transmitted first `1` LSB is transmitted first
CPOL	29	Clock Polarity `0` SCK is low when idle `1` SCK is high when idle
CPHA	28	Clock Phase `0` The data is sampled on a leading SCK edge and changed on a trailing SCK edge `1` The data is sampled on a trailing SCK edge and changed on a leading SCK edge
FORM	27:24	Frame Format `0` SPI frame `2` SPI frame with address
DIPO	21:20	Data In Pinout `0` SERCOM PAD0 is used as data input `1` SERCOM PAD1 is used as data input `2` SERCOM PAD2 is used as data input `3` SERCOM PAD3 is used as data input
DOPO	17:16	Data Out Pinout `0` DO on PAD[0], SCK on PAD[1] and SS on PAD[2] `2` DO on PAD[3], SCK on PAD[1] and SS on PAD[2]
IBON	8	Immediate Buffer Overflow Notification
RUNSTDBY	7	Run during Standby
MODE	4:2	Operating Mode `0` USART with external clock `1` USART with internal clock `2` SPI in slave operation `3` SPI in master operation `4` I2C slave operation `5` I2C master operation
ENABLE	1	Enable
SWRST	0	Software Reset

USART_INT.CTRLAUSART Control A

Address: 0x45806000
Reset: 0x00000000
Access: read/write
Size: 32-bit

15 fields

Field	Bits	What it does
DORD	30	Data Order `0` MSB is transmitted first. `1` LSB is transmitted first.
CPOL	29	Clock Polarity
CMODE	28	Communication Mode `0` Asynchronous communication. `1` Synchronous communication.
FORM	27:24	Frame Format `0` USART frame `1` USART frame with parity `2` LIN Master Break and Synck generation `4` LIN Slave break detection and auto-baud `5` Break detection and auto-baud with parity `7` ISO 7816 Communication
SAMPA	23:22	Sample Adjustment
RXPO	21:20	Receive Data Pinout `0` SERCOM PAD0 is used for data reception `1` SERCOM PAD1 is used for data reception `2` SERCOM PAD2 is used for data reception `3` SERCOM PAD3 is used for data reception
TXPO	17:16	Transmit Data Pinout `0` PAD[0] = TxD; PAD[1] = XCK `2` PAD[0] = TxD; PAD[2] = RTS; PAD[3] = CTS `3` PAD[0] = TxD; PAD[1] = XCK; PAD[2] = TE
SAMPR	15:13	Sample `0` 16x oversampling using arithmetic baud rate generation `1` 16x oversampling using fractional baud rate generation `2` 8x oversampling using arithmetic baud rate generation `3` 8x oversampling using fractional baud rate generation `4` 3x oversampling using arithmetic baud rate generation
RXINV	10	Receive Data Invert `0` RxD is not inverted `1` RxD is inverted
TXINV	9	Transmit Data Invert `0` TxD is not inverted `1` TxD is inverted
IBON	8	Immediate Buffer Overflow Notification
RUNSTDBY	7	Run during Standby
MODE	4:2	Operating Mode `0` USART with external clock `1` USART with internal clock `2` SPI in slave operation `3` SPI in master operation `4` I2C slave operation `5` I2C master operation
ENABLE	1	Enable
SWRST	0	Software Reset

I2CM.CTRLBI2CM Control B

Address: 0x45806004
Reset: 0x00000000
Access: read/write
Size: 32-bit

5 fields

Field	Bits	What it does
FIFOCLR	23:22	FIFO Clear `0` No action `1` Clear TX FIFO `2` Clear RX FIFO `3` Clear both TX and RF FIFOs
ACKACT	18	Acknowledge Action
CMD	17:16	Command
QCEN	9	Quick Command Enable
SMEN	8	Smart Mode Enable

I2CS.CTRLBI2CS Control B

Address: 0x45806004
Reset: 0x00000000
Access: read/write
Size: 32-bit

7 fields

Field	Bits	What it does
FIFOCLR	23:22	FIFO Clear `0` No action `1` Clear TX FIFO `2` Clear RX FIFO `3` Clear both TX and RF FIFOs
ACKACT	18	Acknowledge Action
CMD	17:16	Command
AMODE	15:14	Address Mode `0` The slave responds to the address written in ADDR.ADDR masked by the value in ADDR.ADDRMASK `1` The slave responds to the two unique addresses in ADDR and ADDRMASK `2` The slave responds to the range of addresses between and including ADDR and ADDRMASK. ADDR is the upper limit
AACKEN	10	Automatic Address Acknowledge
GCMD	9	PMBus Group Command
SMEN	8	Smart Mode Enable

SPIM.CTRLBSPIM Control B

Address: 0x45806004
Reset: 0x00000000
Access: read/write
Size: 32-bit

7 fields

Field	Bits	What it does
FIFOCLR	23:22	FIFO Clear `0` No action `1` Clear TX FIFO `2` Clear RX FIFO `3` Clear both TX and RF FIFOs
RXEN	17	Receiver Enable
AMODE	15:14	Address Mode `0` ADDRMASK is used as a mask to the AADR register `1` The slave responds to the two unique addresses in ADDR and ADDRMASK `2` The slave responds to the range of addresses between and including ADDR and ADDRMASK. ADDR is the upper limit
MSSEN	13	Master Slave Select Enable `0` Hardware SS control is disabled `1` Hardware SS control is enabled
SSDE	9	Slave Select Low Detect Enable `0` SS low detector is disabled `1` SS low detector is enabled
PLOADEN	6	Data Preload Enable
CHSIZE	2:0	Character Size `0` 8-bits character `1` 9-bits character

SPIS.CTRLBSPIS Control B

Address: 0x45806004
Reset: 0x00000000
Access: read/write
Size: 32-bit

7 fields

Field	Bits	What it does
FIFOCLR	23:22	FIFO Clear `0` No action `1` Clear TX FIFO `2` Clear RX FIFO `3` Clear both TX and RF FIFOs
RXEN	17	Receiver Enable
AMODE	15:14	Address Mode `0` ADDRMASK is used as a mask to the AADR register `1` The slave responds to the two unique addresses in ADDR and ADDRMASK `2` The slave responds to the range of addresses between and including ADDR and ADDRMASK. ADDR is the upper limit
MSSEN	13	Master Slave Select Enable
SSDE	9	Slave Select Low Detect Enable
PLOADEN	6	Data Preload Enable
CHSIZE	2:0	Character Size `0` 8-bits character `1` 9-bits character

USART_INT.CTRLBUSART Control B

Address: 0x45806004
Reset: 0x00000000
Access: read/write
Size: 32-bit

10 fields

Field	Bits	What it does
LINCMD	25:24	LIN Command `0` Normal USART transmission `1` Break field is transmitted when DATA is written `2` Break, synch and identifier are automaticcaly transmitted when DATA is written with the identifier
FIFOCLR	23:22	FIFO Clear `0` No action `1` Clear TX FIFO `2` Clear RX FIFO `3` Clear both TX and RF FIFOs
RXEN	17	Receiver Enable
TXEN	16	Transmitter Enable
PMODE	13	Parity Mode `0` Even parity `1` Odd parity
ENC	10	Encoding Format `0` Data is not encoded `1` Data is IrDA encoded
SFDE	9	Start of Frame Detection Enable
COLDEN	8	Collision Detection Enable
SBMODE	6	Stop Bit Mode `0` One stop bit `1` Two stop bits
CHSIZE	2:0	Character Size `0` 8-bits character `1` 9-bits character `5` 5-bits character `6` 6-bits character `7` 7-bits character

I2CM.CTRLCI2CM Control C

Address: 0x45806008
Reset: 0x00000000
Access: read/write
Size: 32-bit

4 fields

Field	Bits	What it does
RXTRHOLD	29:28	Receive FIFO Threshold `0` Interrupt and DMA triggers are generated when DATA is present in the FIFO `1` Interrupt and DMA triggers are generated when FIFO is half-full `2` Interrupt and DMA triggers are generated when FIFO is full
FIFOEN	27	FIFO Enable
DATA32B	24	Data 32 Bit
TXTRHOLD	31:30	Transmit FIFO Threshold `0` Interrupt and DMA triggers are generated as long as the FIFO is not full `1` Interrupt and DMA triggers are generated when half FIFO space is free `2` Interrupt and DMA triggers are generated as long as the FIFO is not full

I2CS.CTRLCI2CS Control C

Address: 0x45806008
Reset: 0x00000000
Access: read/write
Size: 32-bit

5 fields

Field	Bits	What it does
RXTRHOLD	29:28	Receive FIFO Threshold `0` Interrupt and DMA triggers are generated when DATA is present in the FIFO `1` Interrupt and DMA triggers are generated when FIFO is half-full `2` Interrupt and DMA triggers are generated when FIFO is full
FIFOEN	27	FIFO Enable
DATA32B	24	Data 32 Bit
SDASETUP	3:0	SDA Setup Time
TXTRHOLD	31:30	Transmit FIFO Threshold `0` Interrupt and DMA triggers are generated as long as the FIFO is not full `1` Interrupt and DMA triggers are generated when half FIFO space is free `2` Interrupt and DMA triggers are generated as long as the FIFO is not full

SPIM.CTRLCSPIM Control C

Address: 0x45806008
Reset: 0x00000000
Access: read/write
Size: 32-bit

11 fields

Field	Bits	What it does
RXTRHOLD	29:28	Receive FIFO Threshold `0` Interrupt and DMA triggers are generated when DATA is present in the FIFO `1` Interrupt and DMA triggers are generated when FIFO is half-full `2` Interrupt and DMA triggers are generated when FIFO is full
FIFOEN	27	FIFO Enable
DATA32B	24	Data 32 Bit
FMODE	17	Frame mode `0` Frame Master `1` Frame Slave
FRMEN	16	Frame mode enable
IGNTUR	11	Ignore Transmit Underrun
FSPOL	10	Frame Synch Polarity `0` VCC-level valid polarity `1` GND-level valid polarity
FSLEN	9	Frame Synch Length `0` One SCK pulse `1` One frame duration
FSES	8	Frame Synch Edge Select
ICSPACE	5:0	Inter-Character Spacing
TXTRHOLD	31:30	Transmit FIFO Threshold `0` Interrupt and DMA triggers are generated as long as the FIFO is not full `1` Interrupt and DMA triggers are generated when half FIFO space is free `2` Interrupt and DMA triggers are generated as long as the FIFO is empty

SPIS.CTRLCSPIS Control C

Address: 0x45806008
Reset: 0x00000000
Access: read/write
Size: 32-bit

11 fields

Field	Bits	What it does
RXTRHOLD	29:28	Receive FIFO Threshold `0` Interrupt and DMA triggers are generated when DATA is present in the FIFO `1` Interrupt and DMA triggers are generated when FIFO is half-full `2` Interrupt and DMA triggers are generated when FIFO is full
FIFOEN	27	FIFO Enable
DATA32B	24	Data 32 Bit
FMODE	17	Frame mode `0` Frame Master `1` Frame Slave
FRMEN	16	Frame mode enable
IGNTUR	11	Ignore Transmit Underrun
FSPOL	10	Frame Synch Polarity `0` VCC-level valid polarity `1` GND-level valid polarity
FSLEN	9	Frame Synch Length `0` One SCK pulse `1` One frame duration
FSES	8	Frame Synch Edge Select
ICSPACE	5:0	Inter-Character Spacing
TXTRHOLD	31:30	Transmit FIFO Threshold `0` Interrupt and DMA triggers are generated as long as the FIFO is not full `1` Interrupt and DMA triggers are generated when half FIFO space is free `2` Interrupt and DMA triggers are generated as long as the FIFO is empty

USART_INT.CTRLCUSART Control C

Address: 0x45806008
Reset: 0x00000000
Access: read/write
Size: 32-bit

10 fields

Field	Bits	What it does
RXTRHOLD	29:28	Receive FIFO Threshold `0` Interrupt and DMA triggers are generated when DATA is present in the FIFO `1` Interrupt and DMA triggers are generated when FIFO is half-full `2` Interrupt and DMA triggers are generated when FIFO is full
FIFOEN	27	FIFO Enable
DATA32B	25:24	Data 32 Bit
MAXITER	22:20	Maximum Iterations
DSNACK	17	Disable Successive NACK
INACK	16	Inhibit Not Acknowledge
HDRDLY	11:10	LIN Master Header Delay `0` Delay between break and sync transmission is 1-bit time `1` Delay between break and sync transmission is 4-bit time `2` Delay between break and sync transmission is 8-bit time `3` Delay between break and sync transmission is 14-bit time
BRKLEN	9:8	LIN Master Break Length `0` Break field transmission is 13 bit times `1` Break field transmission is 17 bit times `2` Break field transmission is 21 bit times `3` Break field transmission is 26 bit times
GTIME	2:0	Guard Time
TXTRHOLD	31:30	Transmit FIFO Threshold `0` Interrupt and DMA triggers are generated as long as the FIFO is not full `1` Interrupt and DMA triggers are generated when half FIFO space is free `2` Interrupt and DMA triggers are generated when the FIFO is empty

I2CM.BAUDI2CM Baud Rate

Address: 0x4580600C
Reset: 0x00000000
Access: read/write
Size: 32-bit

4 fields

Field	Bits	What it does
HSBAUD	23:16	High Speed Baud Rate Value
BAUDLOW	15:8	Baud Rate Value Low
BAUD	7:0	Baud Rate Value
HSBAUDLOW	31:24	High Speed Baud Rate Value Low

SPIM.BAUDSPIM Baud Rate

Address: 0x4580600C
Reset: 0x00
Access: read/write

7BAUD7
6BAUD6
5BAUD5
4BAUD4
3BAUD3
2BAUD2
1BAUD1
0BAUD0

1 field

Field	Bits	What it does
BAUD	7:0	Baud Rate Value

SPIS.BAUDSPIS Baud Rate

Address: 0x4580600C
Reset: 0x00
Access: read/write

7BAUD7
6BAUD6
5BAUD5
4BAUD4
3BAUD3
2BAUD2
1BAUD1
0BAUD0

1 field

Field	Bits	What it does
BAUD	7:0	Baud Rate Value

USART_INT.BAUDUSART Baud Rate

Address: 0x4580600C
Reset: 0x0000
Access: read/write
Size: 16-bit

3 fields

Field	Bits	What it does
BAUD	15:0	Baud Rate Value
FP	15:13	Fractional Part
BAUD	12:0	Baud Rate Value

USART_INT.RXPLUSART Receive Pulse Length

Address: 0x4580600E
Reset: 0x00
Access: read/write

7RXPL7
6RXPL6
5RXPL5
4RXPL4
3RXPL3
2RXPL2
1RXPL1
0RXPL0

1 field

Field	Bits	What it does
RXPL	7:0	Receive Pulse Length

I2CM.INTENCLRI2CM Interrupt Enable Clear

Address: 0x45806014
Reset: 0x00
Access: read/write

7ERROR
6–
5–
4RXFF
3TXFE
2–
1SB
0MB

5 fields

Field	Bits	What it does
ERROR	7	Combined Error Interrupt Disable
RXFF	4	Rx FIFO Full Interrupt Disable
TXFE	3	Tx FIFO Empty Interrupt Disable
SB	1	Slave On Bus Interrupt Disable
MB	0	Master On Bus Interrupt Disable

I2CS.INTENCLRI2CS Interrupt Enable Clear

Address: 0x45806014
Reset: 0x00
Access: read/write

7ERROR
6–
5–
4RXFF
3TXFE
2DRDY
1AMATCH
0PREC

6 fields

Field	Bits	What it does
ERROR	7	Combined Error Interrupt Disable
RXFF	4	Rx FIFO Full Interrupt Disable
TXFE	3	Tx FIFO Empty Interrupt Disable
DRDY	2	Data Interrupt Disable
AMATCH	1	Address Match Interrupt Disable
PREC	0	Stop Received Interrupt Disable

SPIM.INTENCLRSPIM Interrupt Enable Clear

Address: 0x45806014
Reset: 0x00
Access: read/write

7ERROR
6–
5–
4–
3SSL
2RXC
1TXC
0DRE

5 fields

Field	Bits	What it does
ERROR	7	Combined Error Interrupt Disable
SSL	3	Slave Select Low Interrupt Disable
RXC	2	Receive Complete Interrupt Disable
TXC	1	Transmit Complete Interrupt Disable
DRE	0	Data Register Empty Interrupt Disable

SPIS.INTENCLRSPIS Interrupt Enable Clear

Address: 0x45806014
Reset: 0x00
Access: read/write

7ERROR
6–
5–
4–
3SSL
2RXC
1TXC
0DRE

5 fields

Field	Bits	What it does
ERROR	7	Combined Error Interrupt Disable
SSL	3	Slave Select Low Interrupt Disable
RXC	2	Receive Complete Interrupt Disable
TXC	1	Transmit Complete Interrupt Disable
DRE	0	Data Register Empty Interrupt Disable

USART_INT.INTENCLRUSART Interrupt Enable Clear

Address: 0x45806014
Reset: 0x00
Access: read/write

7ERROR
6–
5RXBRK
4CTSIC
3RXS
2RXC
1TXC
0DRE

7 fields

Field	Bits	What it does
ERROR	7	Combined Error Interrupt Disable
RXBRK	5	Break Received Interrupt Disable
CTSIC	4	Clear To Send Input Change Interrupt Disable
RXS	3	Receive Start Interrupt Disable
RXC	2	Receive Complete Interrupt Disable
TXC	1	Transmit Complete Interrupt Disable
DRE	0	Data Register Empty Interrupt Disable

I2CM.INTENSETI2CM Interrupt Enable Set

Address: 0x45806016
Reset: 0x00
Access: read/write

7ERROR
6–
5–
4RXFF
3TXFE
2–
1SB
0MB

5 fields

Field	Bits	What it does
ERROR	7	Combined Error Interrupt Enable
RXFF	4	Rx FIFO Full Interrupt Enable
TXFE	3	Tx FIFO Empty Interrupt Enable
SB	1	Slave On Bus Interrupt Enable
MB	0	Master On Bus Interrupt Enable

I2CS.INTENSETI2CS Interrupt Enable Set

Address: 0x45806016
Reset: 0x00
Access: read/write

7ERROR
6–
5–
4RXFF
3TXFE
2DRDY
1AMATCH
0PREC

6 fields

Field	Bits	What it does
ERROR	7	Combined Error Interrupt Enable
RXFF	4	Rx FIFO Full Interrupt Enable
TXFE	3	Tx FIFO Empty Interrupt Enable
DRDY	2	Data Interrupt Enable
AMATCH	1	Address Match Interrupt Enable
PREC	0	Stop Received Interrupt Enable

SPIM.INTENSETSPIM Interrupt Enable Set

Address: 0x45806016
Reset: 0x00
Access: read/write

7ERROR
6–
5–
4–
3SSL
2RXC
1TXC
0DRE

5 fields

Field	Bits	What it does
ERROR	7	Combined Error Interrupt Enable
SSL	3	Slave Select Low Interrupt Enable
RXC	2	Receive Complete Interrupt Enable
TXC	1	Transmit Complete Interrupt Enable
DRE	0	Data Register Empty Interrupt Enable

SPIS.INTENSETSPIS Interrupt Enable Set

Address: 0x45806016
Reset: 0x00
Access: read/write

7ERROR
6–
5–
4–
3SSL
2RXC
1TXC
0DRE

5 fields

Field	Bits	What it does
ERROR	7	Combined Error Interrupt Enable
SSL	3	Slave Select Low Interrupt Enable
RXC	2	Receive Complete Interrupt Enable
TXC	1	Transmit Complete Interrupt Enable
DRE	0	Data Register Empty Interrupt Enable

USART_INT.INTENSETUSART Interrupt Enable Set

Address: 0x45806016
Reset: 0x00
Access: read/write

7ERROR
6–
5RXBRK
4CTSIC
3RXS
2RXC
1TXC
0DRE

7 fields

Field	Bits	What it does
ERROR	7	Combined Error Interrupt Enable
RXBRK	5	Break Received Interrupt Enable
CTSIC	4	Clear To Send Input Change Interrupt Enable
RXS	3	Receive Start Interrupt Enable
RXC	2	Receive Complete Interrupt Enable
TXC	1	Transmit Complete Interrupt Enable
DRE	0	Data Register Empty Interrupt Enable

I2CM.INTFLAGI2CM Interrupt Flag Status and Clear

Address: 0x45806018
Reset: 0x00
Access: read/write

7ERROR
6–
5–
4RXFF
3TXFE
2–
1SB
0MB

5 fields

Field	Bits	What it does
ERROR	7	Combined Error Interrupt
RXFF	4	Rx FIFO Full Interrupt
TXFE	3	Tx FIFO Empty Interrupt
SB	1	Slave On Bus Interrupt
MB	0	Master On Bus Interrupt

I2CS.INTFLAGI2CS Interrupt Flag Status and Clear

Address: 0x45806018
Reset: 0x00
Access: read/write

7ERROR
6–
5–
4RXFF
3TXFE
2DRDY
1AMATCH
0PREC

6 fields

Field	Bits	What it does
ERROR	7	Combined Error Interrupt
RXFF	4	Rx FIFO Full Interrupt
TXFE	3	Tx FIFO Empty Interrupt
DRDY	2	Data Interrupt
AMATCH	1	Address Match Interrupt
PREC	0	Stop Received Interrupt

SPIM.INTFLAGSPIM Interrupt Flag Status and Clear

Address: 0x45806018
Reset: 0x00
Access: read/write

7ERROR
6–
5–
4–
3SSL
2RXC
1TXC
0DRE

5 fields

Field	Bits	What it does
ERROR	7	Combined Error Interrupt
SSL	3	Slave Select Low Interrupt Flag
RXC	2	Receive Complete Interrupt
TXC	1	Transmit Complete Interrupt
DRE	0	Data Register Empty Interrupt

SPIS.INTFLAGSPIS Interrupt Flag Status and Clear

Address: 0x45806018
Reset: 0x00
Access: read/write

7ERROR
6–
5–
4–
3SSL
2RXC
1TXC
0DRE

5 fields

Field	Bits	What it does
ERROR	7	Combined Error Interrupt
SSL	3	Slave Select Low Interrupt Flag
RXC	2	Receive Complete Interrupt
TXC	1	Transmit Complete Interrupt
DRE	0	Data Register Empty Interrupt

USART_INT.INTFLAGUSART Interrupt Flag Status and Clear

Address: 0x45806018
Reset: 0x00
Access: read/write

7ERROR
6–
5RXBRK
4CTSIC
3RXS
2RXC
1TXC
0DRE

7 fields

Field	Bits	What it does
ERROR	7	Combined Error Interrupt
RXBRK	5	Break Received Interrupt
CTSIC	4	Clear To Send Input Change Interrupt
RXS	3	Receive Start Interrupt
RXC	2	Receive Complete Interrupt
TXC	1	Transmit Complete Interrupt
DRE	0	Data Register Empty Interrupt

I2CM.STATUSI2CM Status

Address: 0x4580601A
Reset: 0x0000
Access: read/write
Size: 16-bit

9 fields

Field	Bits	What it does
LENERR	10	Length Error
SEXTTOUT	9	Slave SCL Low Extend Timeout
MEXTTOUT	8	Master SCL Low Extend Timeout
CLKHOLD	7	Clock Hold
LOWTOUT	6	SCL Low Timeout
BUSSTATE	5:4	Bus State
RXNACK	2	Received Not Acknowledge
ARBLOST	1	Arbitration Lost
BUSERR	0	Bus Error

I2CS.STATUSI2CS Status

Address: 0x4580601A
Reset: 0x0000
Access: read/write
Size: 16-bit

10 fields

Field	Bits	What it does
LENERR	11	Transaction Length Error
HS	10	High Speed
SEXTTOUT	9	Slave SCL Low Extend Timeout
CLKHOLD	7	Clock Hold
LOWTOUT	6	SCL Low Timeout
SR	4	Repeated Start
DIR	3	Read/Write Direction
RXNACK	2	Received Not Acknowledge
COLL	1	Transmit Collision
BUSERR	0	Bus Error

SPIM.STATUSSPIM Status

Address: 0x4580601A
Reset: 0x0000
Access: read/write
Size: 16-bit

3 fields

Field	Bits	What it does
LENERR	11	Transaction Length Error
TUR	3	Frame Transmit Underrun
BUFOVF	2	Buffer Overflow

SPIS.STATUSSPIS Status

Address: 0x4580601A
Reset: 0x0000
Access: read/write
Size: 16-bit

3 fields

Field	Bits	What it does
LENERR	11	Transaction Length Error
TUR	3	Frame Transmit Underrun
BUFOVF	2	Buffer Overflow

USART_INT.STATUSUSART Status

Address: 0x4580601A
Reset: 0x0000
Access: read/write
Size: 16-bit

8 fields

Field	Bits	What it does
ITER	7	Maximum Number of Repetitions Reached
TXE	6	Transmitter Empty
COLL	5	Collision Detected
ISF	4	Inconsistent Sync Field
CTS	3	Clear To Send
BUFOVF	2	Buffer Overflow
FERR	1	Frame Error
PERR	0	Parity Error

I2CM.SYNCBUSYI2CM Synchronization Busy

Address: 0x4580601C
Reset: 0x00000000
Access: read only
Size: 32-bit

4 fields

Field	Bits	What it does
LENGTH	4	Length Synchronization Busy
SYSOP	2	System Operation Synchronization Busy
ENABLE	1	SERCOM Enable Synchronization Busy
SWRST	0	Software Reset Synchronization Busy

I2CS.SYNCBUSYI2CS Synchronization Busy

Address: 0x4580601C
Reset: 0x00000000
Access: read only
Size: 32-bit

4 fields

Field	Bits	What it does
LENGTH	4	Length Synchronization Busy
SYSOP	2	System Operation Synchronization Busy
ENABLE	1	SERCOM Enable Synchronization Busy
SWRST	0	Software Reset Synchronization Busy

SPIM.SYNCBUSYSPIM Synchronization Busy

Address: 0x4580601C
Reset: 0x00000000
Access: read only
Size: 32-bit

4 fields

Field	Bits	What it does
LENGTH	4	LENGTH Synchronization Busy
CTRLB	2	CTRLB Synchronization Busy
ENABLE	1	SERCOM Enable Synchronization Busy
SWRST	0	Software Reset Synchronization Busy

SPIS.SYNCBUSYSPIS Synchronization Busy

Address: 0x4580601C
Reset: 0x00000000
Access: read only
Size: 32-bit

4 fields

Field	Bits	What it does
LENGTH	4	LENGTH Synchronization Busy
CTRLB	2	CTRLB Synchronization Busy
ENABLE	1	SERCOM Enable Synchronization Busy
SWRST	0	Software Reset Synchronization Busy

USART_INT.SYNCBUSYUSART Synchronization Busy

Address: 0x4580601C
Reset: 0x00000000
Access: read only
Size: 32-bit

5 fields

Field	Bits	What it does
LENGTH	4	LENGTH Synchronization Busy
RXERRCNT	3	RXERRCNT Synchronization Busy
CTRLB	2	CTRLB Synchronization Busy
ENABLE	1	SERCOM Enable Synchronization Busy
SWRST	0	Software Reset Synchronization Busy

USART_INT.RXERRCNTUSART Receive Error Count

Address: 0x45806020
Reset: 0x00
Access: read only

7–
6–
5–
4–
3–
2–
1–
0–

I2CS.LENGTHI2CS Length

Address: 0x45806022
Reset: 0x0000
Access: read/write
Size: 16-bit

2 fields

Field	Bits	What it does
LENEN	8	Data Length Enable
LEN	7:0	Data Length

SPIM.LENGTHSPIM Length

Address: 0x45806022
Reset: 0x0000
Access: read/write
Size: 16-bit

2 fields

Field	Bits	What it does
LENEN	8	Data Length Enable
LEN	7:0	Data Length

SPIS.LENGTHSPIS Length

Address: 0x45806022
Reset: 0x0000
Access: read/write
Size: 16-bit

2 fields

Field	Bits	What it does
LENEN	8	Data Length Enable
LEN	7:0	Data Length

USART_INT.LENGTHUSART Length

Address: 0x45806022
Reset: 0x0000
Access: read/write
Size: 16-bit

2 fields

Field	Bits	What it does
LENEN	9:8	Data Length Enable `0` Length counter is disabled `1` Length counter is enabled for transmit `2` Length counter is enabled for receive
LEN	7:0	Data Length

I2CM.ADDRI2CM Address

Address: 0x45806024
Reset: 0x00000000
Access: read/write
Size: 32-bit

5 fields

Field	Bits	What it does
LEN	23:16	Length
TENBITEN	15	Ten Bit Addressing Enable
HS	14	High Speed Mode
LENEN	13	Length Enable
ADDR	10:0	Address Value

I2CS.ADDRI2CS Address

Address: 0x45806024
Reset: 0x00000000
Access: read/write
Size: 32-bit

4 fields

Field	Bits	What it does
ADDRMASK	26:17	Address Mask
TENBITEN	15	Ten Bit Addressing Enable
ADDR	10:1	Address Value
GENCEN	0	General Call Address Enable

SPIM.ADDRSPIM Address

Address: 0x45806024
Reset: 0x00000000
Access: read/write
Size: 32-bit

2 fields

Field	Bits	What it does
ADDRMASK	23:16	Address Mask
ADDR	7:0	Address Value

SPIS.ADDRSPIS Address

Address: 0x45806024
Reset: 0x00000000
Access: read/write
Size: 32-bit

2 fields

Field	Bits	What it does
ADDRMASK	23:16	Address Mask
ADDR	7:0	Address Value

I2CM.DATAI2CM Data

Address: 0x45806028
Reset: 0x00000000
Access: read/write
Size: 32-bit

1 field

Field	Bits	What it does
DATA	31:0	Data Value

I2CS.DATAI2CS Data

Address: 0x45806028
Reset: 0x00000000
Access: read/write
Size: 32-bit

1 field

Field	Bits	What it does
DATA	31:0	Data Value

SPIM.DATASPIM Data

Address: 0x45806028
Reset: 0x00000000
Access: read/write
Size: 32-bit

1 field

Field	Bits	What it does
DATA	31:0	Data Value

SPIS.DATASPIS Data

Address: 0x45806028
Reset: 0x00000000
Access: read/write
Size: 32-bit

1 field

Field	Bits	What it does
DATA	31:0	Data Value

USART_INT.DATAUSART Data

Address: 0x45806028
Reset: 0x00000000
Access: read/write
Size: 32-bit

1 field

Field	Bits	What it does
DATA	31:0	Data Value

I2CM.DBGCTRLI2CM Debug Control

Address: 0x45806030
Reset: 0x00
Access: read/write

7–
6–
5–
4–
3–
2–
1–
0DBGSTOP

1 field

Field	Bits	What it does
DBGSTOP	0	Debug Mode

SPIM.DBGCTRLSPIM Debug Control

Address: 0x45806030
Reset: 0x00
Access: read/write

7–
6–
5–
4–
3–
2–
1–
0DBGSTOP

1 field

Field	Bits	What it does
DBGSTOP	0	Debug Mode

SPIS.DBGCTRLSPIS Debug Control

Address: 0x45806030
Reset: 0x00
Access: read/write

7–
6–
5–
4–
3–
2–
1–
0DBGSTOP

1 field

Field	Bits	What it does
DBGSTOP	0	Debug Mode

USART_INT.DBGCTRLUSART Debug Control

Address: 0x45806030
Reset: 0x00
Access: read/write

7–
6–
5–
4–
3–
2–
1–
0DBGSTOP

1 field

Field	Bits	What it does
DBGSTOP	0	Debug Mode

I2CM.FIFOSPACEI2CM FIFO Space

Address: 0x45806034
Reset: 0x0000
Access: read only
Size: 16-bit

2 fields

Field	Bits	What it does
RXSPACE	12:8	Rx FIFO Filled Space
TXSPACE	4:0	Tx FIFO Empty Space

I2CS.FIFOSPACEI2CS FIFO Space

Address: 0x45806034
Reset: 0x0000
Access: read only
Size: 16-bit

2 fields

Field	Bits	What it does
RXSPACE	12:8	Rx FIFO Filled Space
TXSPACE	4:0	Tx FIFO Empty Space

SPIM.FIFOSPACESPIM FIFO Space

Address: 0x45806034
Reset: 0x0000
Access: read only
Size: 16-bit

2 fields

Field	Bits	What it does
RXSPACE	12:8	Rx FIFO Filled Space
TXSPACE	4:0	Tx FIFO Empty Space

SPIS.FIFOSPACESPIS FIFO Space

Address: 0x45806034
Reset: 0x0000
Access: read only
Size: 16-bit

2 fields

Field	Bits	What it does
RXSPACE	12:8	Rx FIFO Filled Space
TXSPACE	4:0	Tx FIFO Empty Space

USART_INT.FIFOSPACEUSART FIFO Space

Address: 0x45806034
Reset: 0x0000
Access: read only
Size: 16-bit

2 fields

Field	Bits	What it does
RXSPACE	12:8	Rx FIFO Filled Space
TXSPACE	4:0	Tx FIFO Empty Space

I2CM.FIFOPTRI2CM FIFO CPU Pointers

Address: 0x45806036
Reset: 0x0000
Access: read/write
Size: 16-bit

2 fields

Field	Bits	What it does
CPURDPTR	11:8	CPU FIFO Read Pointer
CPUWRPTR	3:0	CPU FIFO Write Pointer

I2CS.FIFOPTRI2CS FIFO CPU Pointers

Address: 0x45806036
Reset: 0x0000
Access: read/write
Size: 16-bit

2 fields

Field	Bits	What it does
CPURDPTR	11:8	CPU FIFO Read Pointer
CPUWRPTR	3:0	CPU FIFO Write Pointer

SPIM.FIFOPTRSPIM FIFO CPU Pointers

Address: 0x45806036
Reset: 0x0000
Access: read/write
Size: 16-bit

2 fields

Field	Bits	What it does
CPURDPTR	11:8	CPU FIFO Read Pointer
CPUWRPTR	3:0	CPU FIFO Write Pointer

SPIS.FIFOPTRSPIS FIFO CPU Pointers

Address: 0x45806036
Reset: 0x0000
Access: read/write
Size: 16-bit

2 fields

Field	Bits	What it does
CPURDPTR	11:8	CPU FIFO Read Pointer
CPUWRPTR	3:0	CPU FIFO Write Pointer

USART_INT.FIFOPTRUSART FIFO CPU Pointers

Address: 0x45806036
Reset: 0x0000
Access: read/write
Size: 16-bit

2 fields

Field	Bits	What it does
CPURDPTR	11:8	CPU FIFO Read Pointer
CPUWRPTR	3:0	CPU FIFO Write Pointer