PIC32MK0512GPE064 CAN1 registers

The 97 registers of CAN1 (CAN 1), from 0xBF880000, with their reset value and every field. The PIC32MK0512GPE064 has 1494 registers in 110 peripherals, one page each.

Most PIC32 SFRs have three more registers right after them: CLR at +4, SET at +8 and INV at +C (T1CONCLR, T1CONSET, T1CONINV), which clear, set or flip just the bits written as 1, in one write.

CAN1 CAN 1

C1CONCAN Module Control Register

Address: 0xBF880000
Reset: 0x04800000
Access: read/write
Size: 32-bit

8 fields

Field	Bits	What it does
ABAT	27	Abort All Pending Transmissions bit `0` Module will clear this bit when all transmissions aborted `1` Signal all transmit buffers to abort transmission
REQOP	26:24	Request Operation Mode bits `0` Set Normal Operation mode `1` Set Disable mode `2` Set Loopback mode `3` Set Listen Only mode `4` Set Configuration mode `5` Reserved - Do not use `6` Reserved - Do not use `7` Set Listen All Messages mode
OPMOD	23:21	Operation Mode Status bits `0` Module is in Normal Operation mode `1` Module is in Disable mode `2` Module is in Loopback mode `3` Module is in Listen Only mode `4` Module is in Configuration mode `5` Reserved `6` Reserved `7` Module is in Listen All Messages mode
CANCAP	20	CAN Message Receive Time Stamp Timer Capture Enable bit `0` Disable CAN message receive time stamp timer capture and stop CANTMR to conserve power `16` CANTMR value is stored on valid message reception and is stored with the message
ON	15	CAN On bit `0` CAN module is disabled `1` CAN module is enabled
SIDL	13	CAN Stop in Idle bit
CANBUSY	11	CAN Module is Busy bit `0` The CAN module is completely disabled `1` The CAN module is active
DNCNT	4:0	Device Net Filter Bit Number bits

C1CFGCAN Baud Rate Configuration Register

Address: 0xBF880010
Reset: 0x00000000
Access: read/write
Size: 32-bit

8 fields

Field	Bits	What it does
WAKFIL	22	CAN Bus Line Filter Enable bit `0` CAN bus line filter is not used for wake-up `1` Use CAN bus line filter for wake-up
SEG2PH	18:16	Phase Buffer Segment 2 bits `0` Length is 1 x Tq `7` Length is 8 x Tq
SEG2PHTS	15	Phase Segment 2 Time Select bit `0` Maximum of SEG1PH or Information Processing Time `1` Freely programmable
SAM	14	Sample of the CAN Bus Line bit `0` Bus line is sampled once at the sample point `1` Bus line is sampled three times at the sample point
SEG1PH	13:11	Phase Buffer Segment 1 bits `0` Length is 1 x Tq `7` Length is 8 x Tq
PRSEG	10:8	Propagation Time Segment bits `0` Length is 1 x Tq `7` Length is 8 x Tq
SJW	7:6	Synchronization Jump Width bits `0` Length is 1 x Tq `1` Length is 2 x Tq `2` Length is 3 x Tq `3` Length is 4 x Tq
BRP	5:0	Baud Rate Prescaler bits `0` Tq = (2 x 1)/Tpbclk5 `1` Tq = (2 x 2)/Tpbclk5 `62` Tq = (2 x 63)/Tpbclk5 `63` Tq = (2 x 64)/Tpbclk5

C1INTCAN Interrupt Register

Address: 0xBF880020
Reset: 0x00000000
Access: read/write
Size: 32-bit

18 fields

Field	Bits	What it does
WAKIE	30	CAN Bus Activity Wake-up Interrupt Enable bit `0` Interrupt request is not enabled `1` Interrupt request is enabled
CERRIE	29	CAN Bus Error Interrupt Enable bit `0` Interrupt request is not enabled `1` Interrupt request is enabled
SERRIE	28	System Error Interrupt Enable bit `0` Interrupt request is not enabled `1` Interrupt request is enabled
RBOVIE	27	Receive Buffer Overflow Interrupt Enable bit `0` Interrupt request is not enabled `1` Interrupt request is enabled
MODIE	19	Mode Change Interrupt Enable bit `0` Interrupt request is not enabled `1` Interrupt request is enabled
CTMRIE	18	CAN Timestamp Timer Interrupt Enable bit `0` Interrupt request is not enabled `1` Interrupt request is enabled
RBIE	17	Receive Buffer Interrupt Enable bit `0` Interrupt request is not enabled `1` Interrupt request is enabled
TBIE	16	Transmit Buffer Interrupt Enable bit `0` Interrupt request is not enabled `1` Interrupt request is enabled
IVRIF	15	Invalid Message Received Interrupt Flag bit `0` An invalid message interrupt has not occurred `1` An invalid messages interrupt has occurred
WAKIF	14	CAN Bus Activity Wake-up Interrupt Flag bit `0` A bus wake-up activity interrupt has not occurred `1` A bus wake-up activity interrupt has occurred
CERRIF	13	CAN Bus Error Interrupt Flag bit `0` A CAN bus error has not occurred `1` A CAN bus error has occurred
SERRIF	12	System Error Interrupt Flag bit `0` A system error has not occurred `1` A system error occurred (typically an illegal address was presented to the System Bus)
RBOVIF	11	Receive Buffer Overflow Interrupt Flag bit `0` A receive buffer overflow has not occurred `1` A receive buffer overflow has occurred
MODIF	3	CAN Mode Change Interrupt Flag bit `0` A CAN module mode change has not occurred `1` A CAN module mode change has occurred (OPMOD has changed to reflect REQOP)
CTMRIF	2	CAN Timer Overflow Interrupt Flag bit `0` A CAN timer (CANTMR) overflow has not occurred `1` A CAN timer (CANTMR) overflow has occurred
RBIF	1	Receive Buffer Interrupt Flag bit `0` A receive buffer interrupt is not pending `1` A receive buffer interrupt is pending
TBIF	0	Transmit Buffer Interrupt Flag bit `0` A transmit buffer interrupt is not pending `1` A transmit buffer interrupt is pending
IVRIE	31	Invalid Message Received Interrupt Enable bit `0` Interrupt request is not enabled `1` Interrupt request is enabled

C1VECCAN Interrupt Code Register

Address: 0xBF880030
Reset: 0x00000040
Access: read only
Size: 32-bit

2 fields

Field	Bits	What it does
FILHIT	12:8	Filter Hit Number bit `0` Filter 0 `1` Filter 1 `30` Filter 30 `31` Filter 31
ICODE	6:0	Interrupt Flag Code bits

C1TRECCAN Transmit/Receive Error Count Register

Address: 0xBF880040
Reset: 0x00000000
Access: read only
Size: 32-bit

8 fields

Field	Bits	What it does
TXBO	21
TXBP	20
RXBP	19
TXWARN	18
RXWARN	17
EWARN	16
TERRCNT	15:8
RERRCNT	7:0

C1FSTATCAN FIFO Status Register

Address: 0xBF880050
Reset: 0x00000000
Access: read only
Size: 32-bit

1 field

Field	Bits	What it does
FIFOIP	15:0	FIFOx Interrupt Pending bits `0` No FIFO interrupts are pending `1` One or more enabled FIFO interrupts are pending

C1RXOVFCAN Receive FIFO Overflow Status Register

Address: 0xBF880060
Reset: 0x00000000
Access: read only
Size: 32-bit

1 field

Field	Bits	What it does
RXOVF	15:0	FIFOx Receive Overflow Interrupt Pending bit `0` FIFO has not overflowed `1` FIFO has overflowed

C1TMRCAN Timer Register

Address: 0xBF880070
Reset: 0x00000000
Access: read/write
Size: 32-bit

2 fields

Field	Bits	What it does
CANTSPRE	15:0	CAN Time Stamp Timer Prescaler bits `-1` CAN time stamp timer (CANTS) increments every 65,535 system clocks `0` CAN time stamp timer (CANTS) increments every system clock
CANTS	31:16

C1RXM0CAN Acceptance Filter Mask

Address: 0xBF880080
Reset: 0x00000000
Access: read/write
Size: 32-bit

3 fields

Field	Bits	What it does
MIDE	19	Identifier Receive Mode bit `0` Match either standard or extended address message if filters match (that is, if (Filter SID) = (Message SID) or if (FILTER SID/EID) = (Message SID/EID)) `1` Match only message types (standard/extended address) that correspond to the EXID bit in filter
EID	17:0	Extended Identifier bits `0` Bit EIDx is dont care in filter operation `1` Include bit, EIDx, in filter comparison
SID	31:21	Standard Identifier bits `0` Bit SIDx is dont care in filter operation `1` Include bit, SIDx, in filter comparison

C1RXM1CAN Acceptance Filter Mask

Address: 0xBF880090
Reset: 0x00000000
Access: read/write
Size: 32-bit

3 fields

Field	Bits	What it does
MIDE	19	Identifier Receive Mode bit `0` Match either standard or extended address message if filters match (that is, if (Filter SID) = (Message SID) or if (FILTER SID/EID) = (Message SID/EID)) `1` Match only message types (standard/extended address) that correspond to the EXID bit in filter
EID	17:0	Extended Identifier bits `0` Bit EIDx is dont care in filter operation `1` Include bit, EIDx, in filter comparison
SID	31:21	Standard Identifier bits `0` Bit SIDx is dont care in filter operation `1` Include bit, SIDx, in filter comparison

C1RXM2CAN Acceptance Filter Mask

Address: 0xBF8800A0
Reset: 0x00000000
Access: read/write
Size: 32-bit

3 fields

Field	Bits	What it does
MIDE	19	Identifier Receive Mode bit `0` Match either standard or extended address message if filters match (that is, if (Filter SID) = (Message SID) or if (FILTER SID/EID) = (Message SID/EID)) `1` Match only message types (standard/extended address) that correspond to the EXID bit in filter
EID	17:0	Extended Identifier bits `0` Bit EIDx is dont care in filter operation `1` Include bit, EIDx, in filter comparison
SID	31:21	Standard Identifier bits `0` Bit SIDx is dont care in filter operation `1` Include bit, SIDx, in filter comparison

C1RXM3CAN Acceptance Filter Mask

Address: 0xBF8800B0
Reset: 0x00000000
Access: read/write
Size: 32-bit

3 fields

Field	Bits	What it does
MIDE	19	Identifier Receive Mode bit `0` Match either standard or extended address message if filters match (that is, if (Filter SID) = (Message SID) or if (FILTER SID/EID) = (Message SID/EID)) `1` Match only message types (standard/extended address) that correspond to the EXID bit in filter
EID	17:0	Extended Identifier bits `0` Bit EIDx is dont care in filter operation `1` Include bit, EIDx, in filter comparison
SID	31:21	Standard Identifier bits `0` Bit SIDx is dont care in filter operation `1` Include bit, SIDx, in filter comparison

C1FLTCON0CAN Filter Control Register 0

Address: 0xBF8800C0
Reset: 0x00000000
Access: read/write
Size: 32-bit

12 fields

Field	Bits	What it does
MSEL3	30:29	Filter 3 Mask Select bits `0` Acceptance Mask 0 selected `1` Acceptance Mask 1 selected `2` Acceptance Mask 2 selected `3` Acceptance Mask 3 selected
FSEL3	28:24	FIFO Selection bits `0` Message matching filter is stored in FIFO buffer 0 `1` Message matching filter is stored in FIFO buffer 1 `2` Message matching filter is stored in FIFO buffer 2 `3` Message matching filter is stored in FIFO buffer 3 `4` Message matching filter is stored in FIFO buffer 4 `5` Message matching filter is stored in FIFO buffer 5 `6` Message matching filter is stored in FIFO buffer 6 `7` Message matching filter is stored in FIFO buffer 7 `8` Message matching filter is stored in FIFO buffer 8 `9` Message matching filter is stored in FIFO buffer 9 `10` Message matching filter is stored in FIFO buffer 10 `11` Message matching filter is stored in FIFO buffer 11 `12` Message matching filter is stored in FIFO buffer 12 `13` Message matching filter is stored in FIFO buffer 13 `14` Message matching filter is stored in FIFO buffer 14 `15` Message matching filter is stored in FIFO buffer 15
FLTEN2	23	Filter 2 Enable bit `0` Filter is disabled `1` Filter is enabled
MSEL2	22:21	Filter 2 Mask Select bits `0` Acceptance Mask 0 selected `1` Acceptance Mask 1 selected `2` Acceptance Mask 2 selected `3` Acceptance Mask 3 selected
FSEL2	20:16	FIFO Selection bits `0` Message matching filter is stored in FIFO buffer 0 `1` Message matching filter is stored in FIFO buffer 1 `2` Message matching filter is stored in FIFO buffer 2 `3` Message matching filter is stored in FIFO buffer 3 `4` Message matching filter is stored in FIFO buffer 4 `5` Message matching filter is stored in FIFO buffer 5 `6` Message matching filter is stored in FIFO buffer 6 `7` Message matching filter is stored in FIFO buffer 7 `8` Message matching filter is stored in FIFO buffer 8 `9` Message matching filter is stored in FIFO buffer 9 `10` Message matching filter is stored in FIFO buffer 10 `11` Message matching filter is stored in FIFO buffer 11 `12` Message matching filter is stored in FIFO buffer 12 `13` Message matching filter is stored in FIFO buffer 13 `14` Message matching filter is stored in FIFO buffer 14 `15` Message matching filter is stored in FIFO buffer 15
FLTEN1	15	Filter 1 Enable bit `0` Filter is disabled `1` Filter is enabled
MSEL1	14:13	Filter 1 Mask Select bits `0` Acceptance Mask 0 selected `1` Acceptance Mask 1 selected `2` Acceptance Mask 2 selected `3` Acceptance Mask 3 selected
FSEL1	12:8	FIFO Selection bits `0` Message matching filter is stored in FIFO buffer 0 `1` Message matching filter is stored in FIFO buffer 1 `2` Message matching filter is stored in FIFO buffer 2 `3` Message matching filter is stored in FIFO buffer 3 `4` Message matching filter is stored in FIFO buffer 4 `5` Message matching filter is stored in FIFO buffer 5 `6` Message matching filter is stored in FIFO buffer 6 `7` Message matching filter is stored in FIFO buffer 7 `8` Message matching filter is stored in FIFO buffer 8 `9` Message matching filter is stored in FIFO buffer 9 `10` Message matching filter is stored in FIFO buffer 10 `11` Message matching filter is stored in FIFO buffer 11 `12` Message matching filter is stored in FIFO buffer 12 `13` Message matching filter is stored in FIFO buffer 13 `14` Message matching filter is stored in FIFO buffer 14 `15` Message matching filter is stored in FIFO buffer 15
FLTEN0	7	Filter 0 Enable bit `0` Filter is disabled `1` Filter is enabled
MSEL0	6:5	Filter 0 Mask Select bits `0` Acceptance Mask 0 selected `1` Acceptance Mask 1 selected `2` Acceptance Mask 2 selected `3` Acceptance Mask 3 selected
FSEL0	4:0	FIFO Selection bits `0` Message matching filter is stored in FIFO buffer 0 `1` Message matching filter is stored in FIFO buffer 1 `2` Message matching filter is stored in FIFO buffer 2 `3` Message matching filter is stored in FIFO buffer 3 `4` Message matching filter is stored in FIFO buffer 4 `5` Message matching filter is stored in FIFO buffer 5 `6` Message matching filter is stored in FIFO buffer 6 `7` Message matching filter is stored in FIFO buffer 7 `8` Message matching filter is stored in FIFO buffer 8 `9` Message matching filter is stored in FIFO buffer 9 `10` Message matching filter is stored in FIFO buffer 10 `11` Message matching filter is stored in FIFO buffer 11 `12` Message matching filter is stored in FIFO buffer 12 `13` Message matching filter is stored in FIFO buffer 13 `14` Message matching filter is stored in FIFO buffer 14 `15` Message matching filter is stored in FIFO buffer 15
FLTEN3	31	Filter 3 Enable bit `0` Filter is disabled `1` Filter is enabled

C1FLTCON1CAN Filter Control Register 1

Address: 0xBF8800D0
Reset: 0x00000000
Access: read/write
Size: 32-bit

12 fields

Field	Bits	What it does
MSEL7	30:29	Filter 7 Mask Select bits `0` Acceptance Mask 0 selected `1` Acceptance Mask 1 selected `2` Acceptance Mask 2 selected `3` Acceptance Mask 3 selected
FSEL7	28:24	FIFO Selection bits `0` Message matching filter is stored in FIFO buffer 0 `1` Message matching filter is stored in FIFO buffer 1 `2` Message matching filter is stored in FIFO buffer 2 `3` Message matching filter is stored in FIFO buffer 3 `4` Message matching filter is stored in FIFO buffer 4 `5` Message matching filter is stored in FIFO buffer 5 `6` Message matching filter is stored in FIFO buffer 6 `7` Message matching filter is stored in FIFO buffer 7 `8` Message matching filter is stored in FIFO buffer 8 `9` Message matching filter is stored in FIFO buffer 9 `10` Message matching filter is stored in FIFO buffer 10 `11` Message matching filter is stored in FIFO buffer 11 `12` Message matching filter is stored in FIFO buffer 12 `13` Message matching filter is stored in FIFO buffer 13 `14` Message matching filter is stored in FIFO buffer 14 `15` Message matching filter is stored in FIFO buffer 15
FLTEN6	23	Filter 6 Enable bit `0` Filter is disabled `1` Filter is enabled
MSEL6	22:21	Filter 6 Mask Select bits `0` Acceptance Mask 0 selected `1` Acceptance Mask 1 selected `2` Acceptance Mask 2 selected `3` Acceptance Mask 3 selected
FSEL6	20:16	FIFO Selection bits `0` Message matching filter is stored in FIFO buffer 0 `1` Message matching filter is stored in FIFO buffer 1 `2` Message matching filter is stored in FIFO buffer 2 `3` Message matching filter is stored in FIFO buffer 3 `4` Message matching filter is stored in FIFO buffer 4 `5` Message matching filter is stored in FIFO buffer 5 `6` Message matching filter is stored in FIFO buffer 6 `7` Message matching filter is stored in FIFO buffer 7 `8` Message matching filter is stored in FIFO buffer 8 `9` Message matching filter is stored in FIFO buffer 9 `10` Message matching filter is stored in FIFO buffer 10 `11` Message matching filter is stored in FIFO buffer 11 `12` Message matching filter is stored in FIFO buffer 12 `13` Message matching filter is stored in FIFO buffer 13 `14` Message matching filter is stored in FIFO buffer 14 `15` Message matching filter is stored in FIFO buffer 15
FLTEN5	15	Filter 17 Enable bit `0` Filter is disabled `1` Filter is enabled
MSEL5	14:13	Filter 5 Mask Select bits `0` Acceptance Mask 0 selected `1` Acceptance Mask 1 selected `2` Acceptance Mask 2 selected `3` Acceptance Mask 3 selected
FSEL5	12:8	FIFO Selection bits `0` Message matching filter is stored in FIFO buffer 0 `1` Message matching filter is stored in FIFO buffer 1 `2` Message matching filter is stored in FIFO buffer 2 `3` Message matching filter is stored in FIFO buffer 3 `4` Message matching filter is stored in FIFO buffer 4 `5` Message matching filter is stored in FIFO buffer 5 `6` Message matching filter is stored in FIFO buffer 6 `7` Message matching filter is stored in FIFO buffer 7 `8` Message matching filter is stored in FIFO buffer 8 `9` Message matching filter is stored in FIFO buffer 9 `10` Message matching filter is stored in FIFO buffer 10 `11` Message matching filter is stored in FIFO buffer 11 `12` Message matching filter is stored in FIFO buffer 12 `13` Message matching filter is stored in FIFO buffer 13 `14` Message matching filter is stored in FIFO buffer 14 `15` Message matching filter is stored in FIFO buffer 15
FLTEN4	7	Filter 4 Enable bit `0` Filter is disabled `1` Filter is enabled
MSEL4	6:5	Filter 4 Mask Select bits `0` Acceptance Mask 0 selected `1` Acceptance Mask 1 selected `2` Acceptance Mask 2 selected `3` Acceptance Mask 3 selected
FSEL4	4:0	FIFO Selection bits `0` Message matching filter is stored in FIFO buffer 0 `1` Message matching filter is stored in FIFO buffer 1 `2` Message matching filter is stored in FIFO buffer 2 `3` Message matching filter is stored in FIFO buffer 3 `4` Message matching filter is stored in FIFO buffer 4 `5` Message matching filter is stored in FIFO buffer 5 `6` Message matching filter is stored in FIFO buffer 6 `7` Message matching filter is stored in FIFO buffer 7 `8` Message matching filter is stored in FIFO buffer 8 `9` Message matching filter is stored in FIFO buffer 9 `10` Message matching filter is stored in FIFO buffer 10 `11` Message matching filter is stored in FIFO buffer 11 `12` Message matching filter is stored in FIFO buffer 12 `13` Message matching filter is stored in FIFO buffer 13 `14` Message matching filter is stored in FIFO buffer 14 `15` Message matching filter is stored in FIFO buffer 15
FLTEN7	31	Filter 7 Enable bit `0` Filter is disabled `1` Filter is enabled

C1FLTCON2CAN Filter Control Register 2

Address: 0xBF8800E0
Reset: 0x00000000
Access: read/write
Size: 32-bit

12 fields

Field	Bits	What it does
MSEL11	30:29	Filter 11 Mask Select bits `0` Acceptance Mask 0 selected `1` Acceptance Mask 1 selected `2` Acceptance Mask 2 selected `3` Acceptance Mask 3 selected
FSEL11	28:24	FIFO Selection bits `0` Message matching filter is stored in FIFO buffer 0 `1` Message matching filter is stored in FIFO buffer 1 `2` Message matching filter is stored in FIFO buffer 2 `3` Message matching filter is stored in FIFO buffer 3 `4` Message matching filter is stored in FIFO buffer 4 `5` Message matching filter is stored in FIFO buffer 5 `6` Message matching filter is stored in FIFO buffer 6 `7` Message matching filter is stored in FIFO buffer 7 `8` Message matching filter is stored in FIFO buffer 8 `9` Message matching filter is stored in FIFO buffer 9 `10` Message matching filter is stored in FIFO buffer 10 `11` Message matching filter is stored in FIFO buffer 11 `12` Message matching filter is stored in FIFO buffer 12 `13` Message matching filter is stored in FIFO buffer 13 `14` Message matching filter is stored in FIFO buffer 14 `15` Message matching filter is stored in FIFO buffer 15
FLTEN10	23	Filter 10 Enable bit `0` Filter is disabled `1` Filter is enabled
MSEL10	22:21	Filter 10 Mask Select bits `0` Acceptance Mask 0 selected `1` Acceptance Mask 1 selected `2` Acceptance Mask 2 selected `3` Acceptance Mask 3 selected
FSEL10	20:16	FIFO Selection bits `0` Message matching filter is stored in FIFO buffer 0 `1` Message matching filter is stored in FIFO buffer 1 `2` Message matching filter is stored in FIFO buffer 2 `3` Message matching filter is stored in FIFO buffer 3 `4` Message matching filter is stored in FIFO buffer 4 `5` Message matching filter is stored in FIFO buffer 5 `6` Message matching filter is stored in FIFO buffer 6 `7` Message matching filter is stored in FIFO buffer 7 `8` Message matching filter is stored in FIFO buffer 8 `9` Message matching filter is stored in FIFO buffer 9 `10` Message matching filter is stored in FIFO buffer 10 `11` Message matching filter is stored in FIFO buffer 11 `12` Message matching filter is stored in FIFO buffer 12 `13` Message matching filter is stored in FIFO buffer 13 `14` Message matching filter is stored in FIFO buffer 14 `15` Message matching filter is stored in FIFO buffer 15
FLTEN9	15	Filter 9 Enable bit `0` Filter is disabled `1` Filter is enabled
MSEL9	14:13	Filter 9 Mask Select bits `0` Acceptance Mask 0 selected `1` Acceptance Mask 1 selected `2` Acceptance Mask 2 selected `3` Acceptance Mask 3 selected
FSEL9	12:8	FIFO Selection bits `0` Message matching filter is stored in FIFO buffer 0 `1` Message matching filter is stored in FIFO buffer 1 `2` Message matching filter is stored in FIFO buffer 2 `3` Message matching filter is stored in FIFO buffer 3 `4` Message matching filter is stored in FIFO buffer 4 `5` Message matching filter is stored in FIFO buffer 5 `6` Message matching filter is stored in FIFO buffer 6 `7` Message matching filter is stored in FIFO buffer 7 `8` Message matching filter is stored in FIFO buffer 8 `9` Message matching filter is stored in FIFO buffer 9 `10` Message matching filter is stored in FIFO buffer 10 `11` Message matching filter is stored in FIFO buffer 11 `12` Message matching filter is stored in FIFO buffer 12 `13` Message matching filter is stored in FIFO buffer 13 `14` Message matching filter is stored in FIFO buffer 14 `15` Message matching filter is stored in FIFO buffer 15
FLTEN8	7	Filter 8 Enable bit `0` Filter is disabled `1` Filter is enabled
MSEL8	6:5	Filter 8 Mask Select bits `0` Acceptance Mask 0 selected `1` Acceptance Mask 1 selected `2` Acceptance Mask 2 selected `3` Acceptance Mask 3 selected
FSEL8	4:0	FIFO Selection bits `0` Message matching filter is stored in FIFO buffer 0 `1` Message matching filter is stored in FIFO buffer 1 `2` Message matching filter is stored in FIFO buffer 2 `3` Message matching filter is stored in FIFO buffer 3 `4` Message matching filter is stored in FIFO buffer 4 `5` Message matching filter is stored in FIFO buffer 5 `6` Message matching filter is stored in FIFO buffer 6 `7` Message matching filter is stored in FIFO buffer 7 `8` Message matching filter is stored in FIFO buffer 8 `9` Message matching filter is stored in FIFO buffer 9 `10` Message matching filter is stored in FIFO buffer 10 `11` Message matching filter is stored in FIFO buffer 11 `12` Message matching filter is stored in FIFO buffer 12 `13` Message matching filter is stored in FIFO buffer 13 `14` Message matching filter is stored in FIFO buffer 14 `15` Message matching filter is stored in FIFO buffer 15
FLTEN11	31	Filter 11 Enable bit `0` Filter is disabled `1` Filter is enabled

C1FLTCON3CAN Filter Control Register 3

Address: 0xBF8800F0
Reset: 0x00000000
Access: read/write
Size: 32-bit

12 fields

Field	Bits	What it does
MSEL15	30:29	Filter 15 Mask Select bits `0` Acceptance Mask 0 selected `1` Acceptance Mask 1 selected `2` Acceptance Mask 2 selected `3` Acceptance Mask 3 selected
FSEL15	28:24	FIFO Selection bits `0` Message matching filter is stored in FIFO buffer 0 `1` Message matching filter is stored in FIFO buffer 1 `2` Message matching filter is stored in FIFO buffer 2 `3` Message matching filter is stored in FIFO buffer 3 `4` Message matching filter is stored in FIFO buffer 4 `5` Message matching filter is stored in FIFO buffer 5 `6` Message matching filter is stored in FIFO buffer 6 `7` Message matching filter is stored in FIFO buffer 7 `8` Message matching filter is stored in FIFO buffer 8 `9` Message matching filter is stored in FIFO buffer 9 `10` Message matching filter is stored in FIFO buffer 10 `11` Message matching filter is stored in FIFO buffer 11 `12` Message matching filter is stored in FIFO buffer 12 `13` Message matching filter is stored in FIFO buffer 13 `14` Message matching filter is stored in FIFO buffer 14 `15` Message matching filter is stored in FIFO buffer 15
FLTEN14	23	Filter 14 Enable bit `0` Filter is disabled `1` Filter is enabled
MSEL14	22:21	Filter 14 Mask Select bits `0` Acceptance Mask 0 selected `1` Acceptance Mask 1 selected `2` Acceptance Mask 2 selected `3` Acceptance Mask 3 selected
FSEL14	20:16	FIFO Selection bits `0` Message matching filter is stored in FIFO buffer 0 `1` Message matching filter is stored in FIFO buffer 1 `2` Message matching filter is stored in FIFO buffer 2 `3` Message matching filter is stored in FIFO buffer 3 `4` Message matching filter is stored in FIFO buffer 4 `5` Message matching filter is stored in FIFO buffer 5 `6` Message matching filter is stored in FIFO buffer 6 `7` Message matching filter is stored in FIFO buffer 7 `8` Message matching filter is stored in FIFO buffer 8 `9` Message matching filter is stored in FIFO buffer 9 `10` Message matching filter is stored in FIFO buffer 10 `11` Message matching filter is stored in FIFO buffer 11 `12` Message matching filter is stored in FIFO buffer 12 `13` Message matching filter is stored in FIFO buffer 13 `14` Message matching filter is stored in FIFO buffer 14 `15` Message matching filter is stored in FIFO buffer 15
FLTEN13	15	Filter 13 Enable bit `0` Filter is disabled `1` Filter is enabled
MSEL13	14:13	Filter 13 Mask Select bits `0` Acceptance Mask 0 selected `1` Acceptance Mask 1 selected `2` Acceptance Mask 2 selected `3` Acceptance Mask 3 selected
FSEL13	12:8	FIFO Selection bits `0` Message matching filter is stored in FIFO buffer 0 `1` Message matching filter is stored in FIFO buffer 1 `2` Message matching filter is stored in FIFO buffer 2 `3` Message matching filter is stored in FIFO buffer 3 `4` Message matching filter is stored in FIFO buffer 4 `5` Message matching filter is stored in FIFO buffer 5 `6` Message matching filter is stored in FIFO buffer 6 `7` Message matching filter is stored in FIFO buffer 7 `8` Message matching filter is stored in FIFO buffer 8 `9` Message matching filter is stored in FIFO buffer 9 `10` Message matching filter is stored in FIFO buffer 10 `11` Message matching filter is stored in FIFO buffer 11 `12` Message matching filter is stored in FIFO buffer 12 `13` Message matching filter is stored in FIFO buffer 13 `14` Message matching filter is stored in FIFO buffer 14 `15` Message matching filter is stored in FIFO buffer 15
FLTEN12	7	Filter 12 Enable bit `0` Filter is disabled `1` Filter is enabled
MSEL12	6:5	Filter 12 Mask Select bits `0` Acceptance Mask 0 selected `1` Acceptance Mask 1 selected `2` Acceptance Mask 2 selected `3` Acceptance Mask 3 selected
FSEL12	4:0	FIFO Selection bits `0` Message matching filter is stored in FIFO buffer 0 `1` Message matching filter is stored in FIFO buffer 1 `2` Message matching filter is stored in FIFO buffer 2 `3` Message matching filter is stored in FIFO buffer 3 `4` Message matching filter is stored in FIFO buffer 4 `5` Message matching filter is stored in FIFO buffer 5 `6` Message matching filter is stored in FIFO buffer 6 `7` Message matching filter is stored in FIFO buffer 7 `8` Message matching filter is stored in FIFO buffer 8 `9` Message matching filter is stored in FIFO buffer 9 `10` Message matching filter is stored in FIFO buffer 10 `11` Message matching filter is stored in FIFO buffer 11 `12` Message matching filter is stored in FIFO buffer 12 `13` Message matching filter is stored in FIFO buffer 13 `14` Message matching filter is stored in FIFO buffer 14 `15` Message matching filter is stored in FIFO buffer 15
FLTEN15	31	Filter 15 Enable bit `0` Filter is disabled `1` Filter is enabled

C1RXF0CAN Acceptance Filter

Address: 0xBF880140
Reset: 0x00000000
Access: read/write
Size: 32-bit

3 fields

Field	Bits	What it does
EXID	19	Extended Identifier Enable bits `0` Match only messages with standard identifier addresses `1` Match only messages with extended identifier addresses
EID	17:0	Extended Identifier bits `0` Message address bit EIDx must be 0 to match filter `1` Message address bit EIDx must be 1 to match filter
SID	31:21	Standard Identifier bits `0` Message address bit SIDx must be 0 to match filter `1` Message address bit SIDx must be 1 to match filter

C1RXF1CAN Acceptance Filter

Address: 0xBF880150
Reset: 0x00000000
Access: read/write
Size: 32-bit

3 fields

Field	Bits	What it does
EXID	19	Extended Identifier Enable bits `0` Match only messages with standard identifier addresses `1` Match only messages with extended identifier addresses
EID	17:0	Extended Identifier bits `0` Message address bit EIDx must be 0 to match filter `1` Message address bit EIDx must be 1 to match filter
SID	31:21	Standard Identifier bits `0` Message address bit SIDx must be 0 to match filter `1` Message address bit SIDx must be 1 to match filter

C1RXF2CAN Acceptance Filter

Address: 0xBF880160
Reset: 0x00000000
Access: read/write
Size: 32-bit

3 fields

Field	Bits	What it does
EXID	19	Extended Identifier Enable bits `0` Match only messages with standard identifier addresses `1` Match only messages with extended identifier addresses
EID	17:0	Extended Identifier bits `0` Message address bit EIDx must be 0 to match filter `1` Message address bit EIDx must be 1 to match filter
SID	31:21	Standard Identifier bits `0` Message address bit SIDx must be 0 to match filter `1` Message address bit SIDx must be 1 to match filter

C1RXF3CAN Acceptance Filter

Address: 0xBF880170
Reset: 0x00000000
Access: read/write
Size: 32-bit

3 fields

Field	Bits	What it does
EXID	19	Extended Identifier Enable bits `0` Match only messages with standard identifier addresses `1` Match only messages with extended identifier addresses
EID	17:0	Extended Identifier bits `0` Message address bit EIDx must be 0 to match filter `1` Message address bit EIDx must be 1 to match filter
SID	31:21	Standard Identifier bits `0` Message address bit SIDx must be 0 to match filter `1` Message address bit SIDx must be 1 to match filter

C1RXF4CAN Acceptance Filter

Address: 0xBF880180
Reset: 0x00000000
Access: read/write
Size: 32-bit

3 fields

Field	Bits	What it does
EXID	19	Extended Identifier Enable bits `0` Match only messages with standard identifier addresses `1` Match only messages with extended identifier addresses
EID	17:0	Extended Identifier bits `0` Message address bit EIDx must be 0 to match filter `1` Message address bit EIDx must be 1 to match filter
SID	31:21	Standard Identifier bits `0` Message address bit SIDx must be 0 to match filter `1` Message address bit SIDx must be 1 to match filter

C1RXF5CAN Acceptance Filter

Address: 0xBF880190
Reset: 0x00000000
Access: read/write
Size: 32-bit

3 fields

Field	Bits	What it does
EXID	19	Extended Identifier Enable bits `0` Match only messages with standard identifier addresses `1` Match only messages with extended identifier addresses
EID	17:0	Extended Identifier bits `0` Message address bit EIDx must be 0 to match filter `1` Message address bit EIDx must be 1 to match filter
SID	31:21	Standard Identifier bits `0` Message address bit SIDx must be 0 to match filter `1` Message address bit SIDx must be 1 to match filter

C1RXF6CAN Acceptance Filter

Address: 0xBF8801A0
Reset: 0x00000000
Access: read/write
Size: 32-bit

3 fields

Field	Bits	What it does
EXID	19	Extended Identifier Enable bits `0` Match only messages with standard identifier addresses `1` Match only messages with extended identifier addresses
EID	17:0	Extended Identifier bits `0` Message address bit EIDx must be 0 to match filter `1` Message address bit EIDx must be 1 to match filter
SID	31:21	Standard Identifier bits `0` Message address bit SIDx must be 0 to match filter `1` Message address bit SIDx must be 1 to match filter

C1RXF7CAN Acceptance Filter

Address: 0xBF8801B0
Reset: 0x00000000
Access: read/write
Size: 32-bit

3 fields

Field	Bits	What it does
EXID	19	Extended Identifier Enable bits `0` Match only messages with standard identifier addresses `1` Match only messages with extended identifier addresses
EID	17:0	Extended Identifier bits `0` Message address bit EIDx must be 0 to match filter `1` Message address bit EIDx must be 1 to match filter
SID	31:21	Standard Identifier bits `0` Message address bit SIDx must be 0 to match filter `1` Message address bit SIDx must be 1 to match filter

C1RXF8CAN Acceptance Filter

Address: 0xBF8801C0
Reset: 0x00000000
Access: read/write
Size: 32-bit

3 fields

Field	Bits	What it does
EXID	19	Extended Identifier Enable bits `0` Match only messages with standard identifier addresses `1` Match only messages with extended identifier addresses
EID	17:0	Extended Identifier bits `0` Message address bit EIDx must be 0 to match filter `1` Message address bit EIDx must be 1 to match filter
SID	31:21	Standard Identifier bits `0` Message address bit SIDx must be 0 to match filter `1` Message address bit SIDx must be 1 to match filter

C1RXF9CAN Acceptance Filter

Address: 0xBF8801D0
Reset: 0x00000000
Access: read/write
Size: 32-bit

3 fields

Field	Bits	What it does
EXID	19	Extended Identifier Enable bits `0` Match only messages with standard identifier addresses `1` Match only messages with extended identifier addresses
EID	17:0	Extended Identifier bits `0` Message address bit EIDx must be 0 to match filter `1` Message address bit EIDx must be 1 to match filter
SID	31:21	Standard Identifier bits `0` Message address bit SIDx must be 0 to match filter `1` Message address bit SIDx must be 1 to match filter

C1RXF10CAN Acceptance Filter

Address: 0xBF8801E0
Reset: 0x00000000
Access: read/write
Size: 32-bit

3 fields

Field	Bits	What it does
EXID	19	Extended Identifier Enable bits `0` Match only messages with standard identifier addresses `1` Match only messages with extended identifier addresses
EID	17:0	Extended Identifier bits `0` Message address bit EIDx must be 0 to match filter `1` Message address bit EIDx must be 1 to match filter
SID	31:21	Standard Identifier bits `0` Message address bit SIDx must be 0 to match filter `1` Message address bit SIDx must be 1 to match filter

C1RXF11CAN Acceptance Filter

Address: 0xBF8801F0
Reset: 0x00000000
Access: read/write
Size: 32-bit

3 fields

Field	Bits	What it does
EXID	19	Extended Identifier Enable bits `0` Match only messages with standard identifier addresses `1` Match only messages with extended identifier addresses
EID	17:0	Extended Identifier bits `0` Message address bit EIDx must be 0 to match filter `1` Message address bit EIDx must be 1 to match filter
SID	31:21	Standard Identifier bits `0` Message address bit SIDx must be 0 to match filter `1` Message address bit SIDx must be 1 to match filter

C1RXF12CAN Acceptance Filter

Address: 0xBF880200
Reset: 0x00000000
Access: read/write
Size: 32-bit

3 fields

Field	Bits	What it does
EXID	19	Extended Identifier Enable bits `0` Match only messages with standard identifier addresses `1` Match only messages with extended identifier addresses
EID	17:0	Extended Identifier bits `0` Message address bit EIDx must be 0 to match filter `1` Message address bit EIDx must be 1 to match filter
SID	31:21	Standard Identifier bits `0` Message address bit SIDx must be 0 to match filter `1` Message address bit SIDx must be 1 to match filter

C1RXF13CAN Acceptance Filter

Address: 0xBF880210
Reset: 0x00000000
Access: read/write
Size: 32-bit

3 fields

Field	Bits	What it does
EXID	19	Extended Identifier Enable bits `0` Match only messages with standard identifier addresses `1` Match only messages with extended identifier addresses
EID	17:0	Extended Identifier bits `0` Message address bit EIDx must be 0 to match filter `1` Message address bit EIDx must be 1 to match filter
SID	31:21	Standard Identifier bits `0` Message address bit SIDx must be 0 to match filter `1` Message address bit SIDx must be 1 to match filter

C1RXF14CAN Acceptance Filter

Address: 0xBF880220
Reset: 0x00000000
Access: read/write
Size: 32-bit

3 fields

Field	Bits	What it does
EXID	19	Extended Identifier Enable bits `0` Match only messages with standard identifier addresses `1` Match only messages with extended identifier addresses
EID	17:0	Extended Identifier bits `0` Message address bit EIDx must be 0 to match filter `1` Message address bit EIDx must be 1 to match filter
SID	31:21	Standard Identifier bits `0` Message address bit SIDx must be 0 to match filter `1` Message address bit SIDx must be 1 to match filter

C1RXF15CAN Acceptance Filter

Address: 0xBF880230
Reset: 0x00000000
Access: read/write
Size: 32-bit

3 fields

Field	Bits	What it does
EXID	19	Extended Identifier Enable bits `0` Match only messages with standard identifier addresses `1` Match only messages with extended identifier addresses
EID	17:0	Extended Identifier bits `0` Message address bit EIDx must be 0 to match filter `1` Message address bit EIDx must be 1 to match filter
SID	31:21	Standard Identifier bits `0` Message address bit SIDx must be 0 to match filter `1` Message address bit SIDx must be 1 to match filter

C1FIFOBACAN Message Buffer Base Address Register

Address: 0xBF880340
Reset: 0x00000000
Access: read/write
Size: 32-bit

C1FIFOCON0CAN FIFO Control Register

Address: 0xBF880350
Reset: 0x00000000
Access: read/write
Size: 32-bit

11 fields

Field	Bits	What it does
FSIZE	20:16	FIFO Size bits `0` FIFO is 1 message deep `1` FIFO is 2 messages deep `2` FIFO is 3 messages deep `31` FIFO is 32 messages deep
FRESET	14	FIFO Reset bits `0` No effect `1` FIFO will be reset when bit is set, cleared by hardware when FIFO is reset. After setting, the user application should poll whether this bit is clear before taking any action
UINC	13	Increment Head/Tail bit `0` 1: (FIFO configured as a Transmit FIFO) When this bit is set, the FIFO head will increment by a single message `0` 0: (FIFO configured as a Receive FIFO) When this bit is set, the FIFO tail will increment by a single message
DONLY	12	Store Message Data Only bit `0` 1: (FIFO configured as a Transmit FIFO) This bit is not used and has no effect. `0` 0: (FIFO configured as a Receive FIFO) 1 = Only data bytes will be stored in the FIFO, 0 = Full message is stored, including identifier
TXEN	7	TX/RX Buffer Selection bit `0` FIFO is a Receive FIFO `1` FIFO is a Transmit FIFO
TXABAT	6	Message Aborted bit `0` Message completed successfully `1` Message was aborted
TXLARB	5	Message Lost Arbitration bit `0` Message did not lose arbitration while being sent `1` Message lost arbitration while being sent
TXERR	4	Error Detected During Transmission bit `0` A bus error did not occur while the message was being sent `1` A bus error occurred while the message was being sent
TXREQ	3	Message Send Request `0` 1: (FIFO configured as a Transmit FIFO) Setting this bit to 1 requests sending a message. The bit will automatically clear when all the messages queued in the FIFO are successfully sent. Clearing the bit to 0 while set will request a message abort. `0` 0: (FIFO configured as a Receive FIFO) This bit has no effect.
RTREN	2	Auto RTR Enable bit `0` When a remote transmit is received, TXREQ will be unaffected `1` When a remote transmit is received, TXREQ will be set
TXPRI	1:0	Message Transmit Priority bits `0` Lowest Message Priority `1` Low Intermediate Message Priority `2` High Intermediate Message Priority `3` Highest Message Priority

C1FIFOINT0CAN FIFO Interrupt Register

Address: 0xBF880360
Reset: 0x00000000
Access: read/write
Size: 32-bit

14 fields

Field	Bits	What it does
TXNFULLIE	26	Transmit FIFO Not Full Interrupt Enable bit `0` Interrupt disabled for FIFO not full `1` Interrupt enabled for FIFO not full
TXHALFIE	25	Transmit FIFO Half Full Interrupt Enable bit `0` Interrupt disabled for FIFO half full `1` Interrupt enabled for FIFO half full
TXEMPTYIE	24	Transmit FIFO Empty Interrupt Enable bit `0` Interrupt disabled for FIFO empty `1` Interrupt enabled for FIFO empty
RXOVFLIE	19	Overflow Interrupt Enable bit `0` Interrupt disabled for overflow event `1` Interrupt enabled for overflow event
RXFULLIE	18	Full Interrupt Enable bit `0` Interrupt disabled for FIFO full `1` Interrupt enabled for FIFO full
RXHALFIE	17	FIFO Half Full Interrupt Enable bit `0` Interrupt disabled for FIFO half full `1` Interrupt enabled for FIFO half full
RXNEMPTYIE	16	Empty Interrupt Enable bit `0` Interrupt disabled for FIFO not empty `1` Interrupt enabled for FIFO not empty
TXNFULLIF	10	Transmit FIFO Not Full Interrupt Flag bit `0` 1: (FIFO configured as a Transmit Buffer) 1 = FIFO is not full, 0 = FIFO is full `0` 0: (FIFO configured as a Receive Buffer) Unused, reads 0
TXHALFIF	9	FIFO Transmit FIFO Half Empty Interrupt Flag bit `0` 1: (FIFO configured as a Transmit Buffer) 1 = FIFO is ? half full, 0 = FIFO is > half full `0` 0: (FIFO configured as a Receive Buffer) Unused, reads 0
TXEMPTYIF	8	Transmit FIFO Empty Interrupt Flag bit `0` 1: (FIFO configured as a Transmit Buffer) 1 = FIFO is empty, 0 = FIFO is not empty, at least 1 message queued to be transmitted `0` 0: (FIFO configured as a Receive Buffer) Unused, reads 0
RXOVFLIF	3	Receive FIFO Overflow Interrupt Flag bit `0` 1: (FIFO configured as a Transmit Buffer) Unused, reads 0 `0` 0: (FIFO configured as a Receive Buffer) 1 = Overflow event has occurred, 0 = No overflow event occurred
RXFULLIF	2	Receive FIFO Full Interrupt Flag bit `0` 1: (FIFO configured as a Transmit Buffer) Unused, reads 0 `0` 0: (FIFO configured as a Receive Buffer) 1 = FIFO is full, 0 = FIFO is not full
RXHALFIF	1	Receive FIFO Half Full Interrupt Flag bit `0` 1: (FIFO configured as a Transmit Buffer) Unused, reads 0 `0` 0: (FIFO configured as a Receive Buffer) 1 = FIFO is ? half full, 0 = FIFO is < half full
RXNEMPTYIF	0	Receive Buffer Not Empty Interrupt Flag bit `0` 0: (FIFO configured as a Receive Buffer) 1 = FIFO is not empty, has at least 1 message, 0 = FIFO is empty `1` 1: (FIFO configured as a Transmit Buffer) Unused, reads 0

C1FIFOUA0CAN FIFO User Address Register

Address: 0xBF880370
Reset: 0x00000000
Access: read only
Size: 32-bit

C1FIFOCI0CAN Module Message Index Register

Address: 0xBF880380
Reset: 0x00000000
Access: read only
Size: 32-bit

1 field

Field	Bits	What it does
CFIFOCI	4:0

C1FIFOCON1CAN FIFO Control Register

Address: 0xBF880390
Reset: 0x00000000
Access: read/write
Size: 32-bit

11 fields

Field	Bits	What it does
FSIZE	20:16	FIFO Size bits `0` FIFO is 1 message deep `1` FIFO is 2 messages deep `2` FIFO is 3 messages deep `31` FIFO is 32 messages deep
FRESET	14	FIFO Reset bits `0` No effect `1` FIFO will be reset when bit is set, cleared by hardware when FIFO is reset. After setting, the user application should poll whether this bit is clear before taking any action
UINC	13	Increment Head/Tail bit `0` 1: (FIFO configured as a Transmit FIFO) When this bit is set, the FIFO head will increment by a single message `0` 0: (FIFO configured as a Receive FIFO) When this bit is set, the FIFO tail will increment by a single message
DONLY	12	Store Message Data Only bit `0` 1: (FIFO configured as a Transmit FIFO) This bit is not used and has no effect. `0` 0: (FIFO configured as a Receive FIFO) 1 = Only data bytes will be stored in the FIFO, 0 = Full message is stored, including identifier
TXEN	7	TX/RX Buffer Selection bit `0` FIFO is a Receive FIFO `1` FIFO is a Transmit FIFO
TXABAT	6	Message Aborted bit `0` Message completed successfully `1` Message was aborted
TXLARB	5	Message Lost Arbitration bit `0` Message did not lose arbitration while being sent `1` Message lost arbitration while being sent
TXERR	4	Error Detected During Transmission bit `0` A bus error did not occur while the message was being sent `1` A bus error occurred while the message was being sent
TXREQ	3	Message Send Request `0` 1: (FIFO configured as a Transmit FIFO) Setting this bit to 1 requests sending a message. The bit will automatically clear when all the messages queued in the FIFO are successfully sent. Clearing the bit to 0 while set will request a message abort. `0` 0: (FIFO configured as a Receive FIFO) This bit has no effect.
RTREN	2	Auto RTR Enable bit `0` When a remote transmit is received, TXREQ will be unaffected `1` When a remote transmit is received, TXREQ will be set
TXPRI	1:0	Message Transmit Priority bits `0` Lowest Message Priority `1` Low Intermediate Message Priority `2` High Intermediate Message Priority `3` Highest Message Priority

C1FIFOINT1CAN FIFO Interrupt Register

Address: 0xBF8803A0
Reset: 0x00000000
Access: read/write
Size: 32-bit

14 fields

Field	Bits	What it does
TXNFULLIE	26	Transmit FIFO Not Full Interrupt Enable bit `0` Interrupt disabled for FIFO not full `1` Interrupt enabled for FIFO not full
TXHALFIE	25	Transmit FIFO Half Full Interrupt Enable bit `0` Interrupt disabled for FIFO half full `1` Interrupt enabled for FIFO half full
TXEMPTYIE	24	Transmit FIFO Empty Interrupt Enable bit `0` Interrupt disabled for FIFO empty `1` Interrupt enabled for FIFO empty
RXOVFLIE	19	Overflow Interrupt Enable bit `0` Interrupt disabled for overflow event `1` Interrupt enabled for overflow event
RXFULLIE	18	Full Interrupt Enable bit `0` Interrupt disabled for FIFO full `1` Interrupt enabled for FIFO full
RXHALFIE	17	FIFO Half Full Interrupt Enable bit `0` Interrupt disabled for FIFO half full `1` Interrupt enabled for FIFO half full
RXNEMPTYIE	16	Empty Interrupt Enable bit `0` Interrupt disabled for FIFO not empty `1` Interrupt enabled for FIFO not empty
TXNFULLIF	10	Transmit FIFO Not Full Interrupt Flag bit `0` 1: (FIFO configured as a Transmit Buffer) 1 = FIFO is not full, 0 = FIFO is full `0` 0: (FIFO configured as a Receive Buffer) Unused, reads 0
TXHALFIF	9	FIFO Transmit FIFO Half Empty Interrupt Flag bit `0` 1: (FIFO configured as a Transmit Buffer) 1 = FIFO is ? half full, 0 = FIFO is > half full `0` 0: (FIFO configured as a Receive Buffer) Unused, reads 0
TXEMPTYIF	8	Transmit FIFO Empty Interrupt Flag bit `0` 1: (FIFO configured as a Transmit Buffer) 1 = FIFO is empty, 0 = FIFO is not empty, at least 1 message queued to be transmitted `0` 0: (FIFO configured as a Receive Buffer) Unused, reads 0
RXOVFLIF	3	Receive FIFO Overflow Interrupt Flag bit `0` 1: (FIFO configured as a Transmit Buffer) Unused, reads 0 `0` 0: (FIFO configured as a Receive Buffer) 1 = Overflow event has occurred, 0 = No overflow event occurred
RXFULLIF	2	Receive FIFO Full Interrupt Flag bit `0` 1: (FIFO configured as a Transmit Buffer) Unused, reads 0 `0` 0: (FIFO configured as a Receive Buffer) 1 = FIFO is full, 0 = FIFO is not full
RXHALFIF	1	Receive FIFO Half Full Interrupt Flag bit `0` 1: (FIFO configured as a Transmit Buffer) Unused, reads 0 `0` 0: (FIFO configured as a Receive Buffer) 1 = FIFO is ? half full, 0 = FIFO is < half full
RXNEMPTYIF	0	Receive Buffer Not Empty Interrupt Flag bit `0` 0: (FIFO configured as a Receive Buffer) 1 = FIFO is not empty, has at least 1 message, 0 = FIFO is empty `1` 1: (FIFO configured as a Transmit Buffer) Unused, reads 0

C1FIFOUA1CAN FIFO User Address Register

Address: 0xBF8803B0
Reset: 0x00000000
Access: read only
Size: 32-bit

C1FIFOCI1CAN Module Message Index Register

Address: 0xBF8803C0
Reset: 0x00000000
Access: read only
Size: 32-bit

1 field

Field	Bits	What it does
CFIFOCI	4:0

C1FIFOCON2CAN FIFO Control Register

Address: 0xBF8803D0
Reset: 0x00000000
Access: read/write
Size: 32-bit

11 fields

Field	Bits	What it does
FSIZE	20:16	FIFO Size bits `0` FIFO is 1 message deep `1` FIFO is 2 messages deep `2` FIFO is 3 messages deep `31` FIFO is 32 messages deep
FRESET	14	FIFO Reset bits `0` No effect `1` FIFO will be reset when bit is set, cleared by hardware when FIFO is reset. After setting, the user application should poll whether this bit is clear before taking any action
UINC	13	Increment Head/Tail bit `0` 1: (FIFO configured as a Transmit FIFO) When this bit is set, the FIFO head will increment by a single message `0` 0: (FIFO configured as a Receive FIFO) When this bit is set, the FIFO tail will increment by a single message
DONLY	12	Store Message Data Only bit `0` 1: (FIFO configured as a Transmit FIFO) This bit is not used and has no effect. `0` 0: (FIFO configured as a Receive FIFO) 1 = Only data bytes will be stored in the FIFO, 0 = Full message is stored, including identifier
TXEN	7	TX/RX Buffer Selection bit `0` FIFO is a Receive FIFO `1` FIFO is a Transmit FIFO
TXABAT	6	Message Aborted bit `0` Message completed successfully `1` Message was aborted
TXLARB	5	Message Lost Arbitration bit `0` Message did not lose arbitration while being sent `1` Message lost arbitration while being sent
TXERR	4	Error Detected During Transmission bit `0` A bus error did not occur while the message was being sent `1` A bus error occurred while the message was being sent
TXREQ	3	Message Send Request `0` 1: (FIFO configured as a Transmit FIFO) Setting this bit to 1 requests sending a message. The bit will automatically clear when all the messages queued in the FIFO are successfully sent. Clearing the bit to 0 while set will request a message abort. `0` 0: (FIFO configured as a Receive FIFO) This bit has no effect.
RTREN	2	Auto RTR Enable bit `0` When a remote transmit is received, TXREQ will be unaffected `1` When a remote transmit is received, TXREQ will be set
TXPRI	1:0	Message Transmit Priority bits `0` Lowest Message Priority `1` Low Intermediate Message Priority `2` High Intermediate Message Priority `3` Highest Message Priority

C1FIFOINT2CAN FIFO Interrupt Register

Address: 0xBF8803E0
Reset: 0x00000000
Access: read/write
Size: 32-bit

14 fields

Field	Bits	What it does
TXNFULLIE	26	Transmit FIFO Not Full Interrupt Enable bit `0` Interrupt disabled for FIFO not full `1` Interrupt enabled for FIFO not full
TXHALFIE	25	Transmit FIFO Half Full Interrupt Enable bit `0` Interrupt disabled for FIFO half full `1` Interrupt enabled for FIFO half full
TXEMPTYIE	24	Transmit FIFO Empty Interrupt Enable bit `0` Interrupt disabled for FIFO empty `1` Interrupt enabled for FIFO empty
RXOVFLIE	19	Overflow Interrupt Enable bit `0` Interrupt disabled for overflow event `1` Interrupt enabled for overflow event
RXFULLIE	18	Full Interrupt Enable bit `0` Interrupt disabled for FIFO full `1` Interrupt enabled for FIFO full
RXHALFIE	17	FIFO Half Full Interrupt Enable bit `0` Interrupt disabled for FIFO half full `1` Interrupt enabled for FIFO half full
RXNEMPTYIE	16	Empty Interrupt Enable bit `0` Interrupt disabled for FIFO not empty `1` Interrupt enabled for FIFO not empty
TXNFULLIF	10	Transmit FIFO Not Full Interrupt Flag bit `0` 1: (FIFO configured as a Transmit Buffer) 1 = FIFO is not full, 0 = FIFO is full `0` 0: (FIFO configured as a Receive Buffer) Unused, reads 0
TXHALFIF	9	FIFO Transmit FIFO Half Empty Interrupt Flag bit `0` 1: (FIFO configured as a Transmit Buffer) 1 = FIFO is ? half full, 0 = FIFO is > half full `0` 0: (FIFO configured as a Receive Buffer) Unused, reads 0
TXEMPTYIF	8	Transmit FIFO Empty Interrupt Flag bit `0` 1: (FIFO configured as a Transmit Buffer) 1 = FIFO is empty, 0 = FIFO is not empty, at least 1 message queued to be transmitted `0` 0: (FIFO configured as a Receive Buffer) Unused, reads 0
RXOVFLIF	3	Receive FIFO Overflow Interrupt Flag bit `0` 1: (FIFO configured as a Transmit Buffer) Unused, reads 0 `0` 0: (FIFO configured as a Receive Buffer) 1 = Overflow event has occurred, 0 = No overflow event occurred
RXFULLIF	2	Receive FIFO Full Interrupt Flag bit `0` 1: (FIFO configured as a Transmit Buffer) Unused, reads 0 `0` 0: (FIFO configured as a Receive Buffer) 1 = FIFO is full, 0 = FIFO is not full
RXHALFIF	1	Receive FIFO Half Full Interrupt Flag bit `0` 1: (FIFO configured as a Transmit Buffer) Unused, reads 0 `0` 0: (FIFO configured as a Receive Buffer) 1 = FIFO is ? half full, 0 = FIFO is < half full
RXNEMPTYIF	0	Receive Buffer Not Empty Interrupt Flag bit `0` 0: (FIFO configured as a Receive Buffer) 1 = FIFO is not empty, has at least 1 message, 0 = FIFO is empty `1` 1: (FIFO configured as a Transmit Buffer) Unused, reads 0

C1FIFOUA2CAN FIFO User Address Register

Address: 0xBF8803F0
Reset: 0x00000000
Access: read only
Size: 32-bit

C1FIFOCI2CAN Module Message Index Register

Address: 0xBF880400
Reset: 0x00000000
Access: read only
Size: 32-bit

1 field

Field	Bits	What it does
CFIFOCI	4:0

C1FIFOCON3CAN FIFO Control Register

Address: 0xBF880410
Reset: 0x00000000
Access: read/write
Size: 32-bit

11 fields

Field	Bits	What it does
FSIZE	20:16	FIFO Size bits `0` FIFO is 1 message deep `1` FIFO is 2 messages deep `2` FIFO is 3 messages deep `31` FIFO is 32 messages deep
FRESET	14	FIFO Reset bits `0` No effect `1` FIFO will be reset when bit is set, cleared by hardware when FIFO is reset. After setting, the user application should poll whether this bit is clear before taking any action
UINC	13	Increment Head/Tail bit `0` 1: (FIFO configured as a Transmit FIFO) When this bit is set, the FIFO head will increment by a single message `0` 0: (FIFO configured as a Receive FIFO) When this bit is set, the FIFO tail will increment by a single message
DONLY	12	Store Message Data Only bit `0` 1: (FIFO configured as a Transmit FIFO) This bit is not used and has no effect. `0` 0: (FIFO configured as a Receive FIFO) 1 = Only data bytes will be stored in the FIFO, 0 = Full message is stored, including identifier
TXEN	7	TX/RX Buffer Selection bit `0` FIFO is a Receive FIFO `1` FIFO is a Transmit FIFO
TXABAT	6	Message Aborted bit `0` Message completed successfully `1` Message was aborted
TXLARB	5	Message Lost Arbitration bit `0` Message did not lose arbitration while being sent `1` Message lost arbitration while being sent
TXERR	4	Error Detected During Transmission bit `0` A bus error did not occur while the message was being sent `1` A bus error occurred while the message was being sent
TXREQ	3	Message Send Request `0` 1: (FIFO configured as a Transmit FIFO) Setting this bit to 1 requests sending a message. The bit will automatically clear when all the messages queued in the FIFO are successfully sent. Clearing the bit to 0 while set will request a message abort. `0` 0: (FIFO configured as a Receive FIFO) This bit has no effect.
RTREN	2	Auto RTR Enable bit `0` When a remote transmit is received, TXREQ will be unaffected `1` When a remote transmit is received, TXREQ will be set
TXPRI	1:0	Message Transmit Priority bits `0` Lowest Message Priority `1` Low Intermediate Message Priority `2` High Intermediate Message Priority `3` Highest Message Priority

C1FIFOINT3CAN FIFO Interrupt Register

Address: 0xBF880420
Reset: 0x00000000
Access: read/write
Size: 32-bit

14 fields

Field	Bits	What it does
TXNFULLIE	26	Transmit FIFO Not Full Interrupt Enable bit `0` Interrupt disabled for FIFO not full `1` Interrupt enabled for FIFO not full
TXHALFIE	25	Transmit FIFO Half Full Interrupt Enable bit `0` Interrupt disabled for FIFO half full `1` Interrupt enabled for FIFO half full
TXEMPTYIE	24	Transmit FIFO Empty Interrupt Enable bit `0` Interrupt disabled for FIFO empty `1` Interrupt enabled for FIFO empty
RXOVFLIE	19	Overflow Interrupt Enable bit `0` Interrupt disabled for overflow event `1` Interrupt enabled for overflow event
RXFULLIE	18	Full Interrupt Enable bit `0` Interrupt disabled for FIFO full `1` Interrupt enabled for FIFO full
RXHALFIE	17	FIFO Half Full Interrupt Enable bit `0` Interrupt disabled for FIFO half full `1` Interrupt enabled for FIFO half full
RXNEMPTYIE	16	Empty Interrupt Enable bit `0` Interrupt disabled for FIFO not empty `1` Interrupt enabled for FIFO not empty
TXNFULLIF	10	Transmit FIFO Not Full Interrupt Flag bit `0` 1: (FIFO configured as a Transmit Buffer) 1 = FIFO is not full, 0 = FIFO is full `0` 0: (FIFO configured as a Receive Buffer) Unused, reads 0
TXHALFIF	9	FIFO Transmit FIFO Half Empty Interrupt Flag bit `0` 1: (FIFO configured as a Transmit Buffer) 1 = FIFO is ? half full, 0 = FIFO is > half full `0` 0: (FIFO configured as a Receive Buffer) Unused, reads 0
TXEMPTYIF	8	Transmit FIFO Empty Interrupt Flag bit `0` 1: (FIFO configured as a Transmit Buffer) 1 = FIFO is empty, 0 = FIFO is not empty, at least 1 message queued to be transmitted `0` 0: (FIFO configured as a Receive Buffer) Unused, reads 0
RXOVFLIF	3	Receive FIFO Overflow Interrupt Flag bit `0` 1: (FIFO configured as a Transmit Buffer) Unused, reads 0 `0` 0: (FIFO configured as a Receive Buffer) 1 = Overflow event has occurred, 0 = No overflow event occurred
RXFULLIF	2	Receive FIFO Full Interrupt Flag bit `0` 1: (FIFO configured as a Transmit Buffer) Unused, reads 0 `0` 0: (FIFO configured as a Receive Buffer) 1 = FIFO is full, 0 = FIFO is not full
RXHALFIF	1	Receive FIFO Half Full Interrupt Flag bit `0` 1: (FIFO configured as a Transmit Buffer) Unused, reads 0 `0` 0: (FIFO configured as a Receive Buffer) 1 = FIFO is ? half full, 0 = FIFO is < half full
RXNEMPTYIF	0	Receive Buffer Not Empty Interrupt Flag bit `0` 0: (FIFO configured as a Receive Buffer) 1 = FIFO is not empty, has at least 1 message, 0 = FIFO is empty `1` 1: (FIFO configured as a Transmit Buffer) Unused, reads 0

C1FIFOUA3CAN FIFO User Address Register

Address: 0xBF880430
Reset: 0x00000000
Access: read only
Size: 32-bit

C1FIFOCI3CAN Module Message Index Register

Address: 0xBF880440
Reset: 0x00000000
Access: read only
Size: 32-bit

1 field

Field	Bits	What it does
CFIFOCI	4:0

C1FIFOCON4CAN FIFO Control Register

Address: 0xBF880450
Reset: 0x00000000
Access: read/write
Size: 32-bit

11 fields

Field	Bits	What it does
FSIZE	20:16	FIFO Size bits `0` FIFO is 1 message deep `1` FIFO is 2 messages deep `2` FIFO is 3 messages deep `31` FIFO is 32 messages deep
FRESET	14	FIFO Reset bits `0` No effect `1` FIFO will be reset when bit is set, cleared by hardware when FIFO is reset. After setting, the user application should poll whether this bit is clear before taking any action
UINC	13	Increment Head/Tail bit `0` 1: (FIFO configured as a Transmit FIFO) When this bit is set, the FIFO head will increment by a single message `0` 0: (FIFO configured as a Receive FIFO) When this bit is set, the FIFO tail will increment by a single message
DONLY	12	Store Message Data Only bit `0` 1: (FIFO configured as a Transmit FIFO) This bit is not used and has no effect. `0` 0: (FIFO configured as a Receive FIFO) 1 = Only data bytes will be stored in the FIFO, 0 = Full message is stored, including identifier
TXEN	7	TX/RX Buffer Selection bit `0` FIFO is a Receive FIFO `1` FIFO is a Transmit FIFO
TXABAT	6	Message Aborted bit `0` Message completed successfully `1` Message was aborted
TXLARB	5	Message Lost Arbitration bit `0` Message did not lose arbitration while being sent `1` Message lost arbitration while being sent
TXERR	4	Error Detected During Transmission bit `0` A bus error did not occur while the message was being sent `1` A bus error occurred while the message was being sent
TXREQ	3	Message Send Request `0` 1: (FIFO configured as a Transmit FIFO) Setting this bit to 1 requests sending a message. The bit will automatically clear when all the messages queued in the FIFO are successfully sent. Clearing the bit to 0 while set will request a message abort. `0` 0: (FIFO configured as a Receive FIFO) This bit has no effect.
RTREN	2	Auto RTR Enable bit `0` When a remote transmit is received, TXREQ will be unaffected `1` When a remote transmit is received, TXREQ will be set
TXPRI	1:0	Message Transmit Priority bits `0` Lowest Message Priority `1` Low Intermediate Message Priority `2` High Intermediate Message Priority `3` Highest Message Priority

C1FIFOINT4CAN FIFO Interrupt Register

Address: 0xBF880460
Reset: 0x00000000
Access: read/write
Size: 32-bit

14 fields

Field	Bits	What it does
TXNFULLIE	26	Transmit FIFO Not Full Interrupt Enable bit `0` Interrupt disabled for FIFO not full `1` Interrupt enabled for FIFO not full
TXHALFIE	25	Transmit FIFO Half Full Interrupt Enable bit `0` Interrupt disabled for FIFO half full `1` Interrupt enabled for FIFO half full
TXEMPTYIE	24	Transmit FIFO Empty Interrupt Enable bit `0` Interrupt disabled for FIFO empty `1` Interrupt enabled for FIFO empty
RXOVFLIE	19	Overflow Interrupt Enable bit `0` Interrupt disabled for overflow event `1` Interrupt enabled for overflow event
RXFULLIE	18	Full Interrupt Enable bit `0` Interrupt disabled for FIFO full `1` Interrupt enabled for FIFO full
RXHALFIE	17	FIFO Half Full Interrupt Enable bit `0` Interrupt disabled for FIFO half full `1` Interrupt enabled for FIFO half full
RXNEMPTYIE	16	Empty Interrupt Enable bit `0` Interrupt disabled for FIFO not empty `1` Interrupt enabled for FIFO not empty
TXNFULLIF	10	Transmit FIFO Not Full Interrupt Flag bit `0` 1: (FIFO configured as a Transmit Buffer) 1 = FIFO is not full, 0 = FIFO is full `0` 0: (FIFO configured as a Receive Buffer) Unused, reads 0
TXHALFIF	9	FIFO Transmit FIFO Half Empty Interrupt Flag bit `0` 1: (FIFO configured as a Transmit Buffer) 1 = FIFO is ? half full, 0 = FIFO is > half full `0` 0: (FIFO configured as a Receive Buffer) Unused, reads 0
TXEMPTYIF	8	Transmit FIFO Empty Interrupt Flag bit `0` 1: (FIFO configured as a Transmit Buffer) 1 = FIFO is empty, 0 = FIFO is not empty, at least 1 message queued to be transmitted `0` 0: (FIFO configured as a Receive Buffer) Unused, reads 0
RXOVFLIF	3	Receive FIFO Overflow Interrupt Flag bit `0` 1: (FIFO configured as a Transmit Buffer) Unused, reads 0 `0` 0: (FIFO configured as a Receive Buffer) 1 = Overflow event has occurred, 0 = No overflow event occurred
RXFULLIF	2	Receive FIFO Full Interrupt Flag bit `0` 1: (FIFO configured as a Transmit Buffer) Unused, reads 0 `0` 0: (FIFO configured as a Receive Buffer) 1 = FIFO is full, 0 = FIFO is not full
RXHALFIF	1	Receive FIFO Half Full Interrupt Flag bit `0` 1: (FIFO configured as a Transmit Buffer) Unused, reads 0 `0` 0: (FIFO configured as a Receive Buffer) 1 = FIFO is ? half full, 0 = FIFO is < half full
RXNEMPTYIF	0	Receive Buffer Not Empty Interrupt Flag bit `0` 0: (FIFO configured as a Receive Buffer) 1 = FIFO is not empty, has at least 1 message, 0 = FIFO is empty `1` 1: (FIFO configured as a Transmit Buffer) Unused, reads 0

C1FIFOUA4CAN FIFO User Address Register

Address: 0xBF880470
Reset: 0x00000000
Access: read only
Size: 32-bit

C1FIFOCI4CAN Module Message Index Register

Address: 0xBF880480
Reset: 0x00000000
Access: read only
Size: 32-bit

1 field

Field	Bits	What it does
CFIFOCI	4:0

C1FIFOCON5CAN FIFO Control Register

Address: 0xBF880490
Reset: 0x00000000
Access: read/write
Size: 32-bit

11 fields

Field	Bits	What it does
FSIZE	20:16	FIFO Size bits `0` FIFO is 1 message deep `1` FIFO is 2 messages deep `2` FIFO is 3 messages deep `31` FIFO is 32 messages deep
FRESET	14	FIFO Reset bits `0` No effect `1` FIFO will be reset when bit is set, cleared by hardware when FIFO is reset. After setting, the user application should poll whether this bit is clear before taking any action
UINC	13	Increment Head/Tail bit `0` 1: (FIFO configured as a Transmit FIFO) When this bit is set, the FIFO head will increment by a single message `0` 0: (FIFO configured as a Receive FIFO) When this bit is set, the FIFO tail will increment by a single message
DONLY	12	Store Message Data Only bit `0` 1: (FIFO configured as a Transmit FIFO) This bit is not used and has no effect. `0` 0: (FIFO configured as a Receive FIFO) 1 = Only data bytes will be stored in the FIFO, 0 = Full message is stored, including identifier
TXEN	7	TX/RX Buffer Selection bit `0` FIFO is a Receive FIFO `1` FIFO is a Transmit FIFO
TXABAT	6	Message Aborted bit `0` Message completed successfully `1` Message was aborted
TXLARB	5	Message Lost Arbitration bit `0` Message did not lose arbitration while being sent `1` Message lost arbitration while being sent
TXERR	4	Error Detected During Transmission bit `0` A bus error did not occur while the message was being sent `1` A bus error occurred while the message was being sent
TXREQ	3	Message Send Request `0` 1: (FIFO configured as a Transmit FIFO) Setting this bit to 1 requests sending a message. The bit will automatically clear when all the messages queued in the FIFO are successfully sent. Clearing the bit to 0 while set will request a message abort. `0` 0: (FIFO configured as a Receive FIFO) This bit has no effect.
RTREN	2	Auto RTR Enable bit `0` When a remote transmit is received, TXREQ will be unaffected `1` When a remote transmit is received, TXREQ will be set
TXPRI	1:0	Message Transmit Priority bits `0` Lowest Message Priority `1` Low Intermediate Message Priority `2` High Intermediate Message Priority `3` Highest Message Priority

C1FIFOINT5CAN FIFO Interrupt Register

Address: 0xBF8804A0
Reset: 0x00000000
Access: read/write
Size: 32-bit

14 fields

Field	Bits	What it does
TXNFULLIE	26	Transmit FIFO Not Full Interrupt Enable bit `0` Interrupt disabled for FIFO not full `1` Interrupt enabled for FIFO not full
TXHALFIE	25	Transmit FIFO Half Full Interrupt Enable bit `0` Interrupt disabled for FIFO half full `1` Interrupt enabled for FIFO half full
TXEMPTYIE	24	Transmit FIFO Empty Interrupt Enable bit `0` Interrupt disabled for FIFO empty `1` Interrupt enabled for FIFO empty
RXOVFLIE	19	Overflow Interrupt Enable bit `0` Interrupt disabled for overflow event `1` Interrupt enabled for overflow event
RXFULLIE	18	Full Interrupt Enable bit `0` Interrupt disabled for FIFO full `1` Interrupt enabled for FIFO full
RXHALFIE	17	FIFO Half Full Interrupt Enable bit `0` Interrupt disabled for FIFO half full `1` Interrupt enabled for FIFO half full
RXNEMPTYIE	16	Empty Interrupt Enable bit `0` Interrupt disabled for FIFO not empty `1` Interrupt enabled for FIFO not empty
TXNFULLIF	10	Transmit FIFO Not Full Interrupt Flag bit `0` 1: (FIFO configured as a Transmit Buffer) 1 = FIFO is not full, 0 = FIFO is full `0` 0: (FIFO configured as a Receive Buffer) Unused, reads 0
TXHALFIF	9	FIFO Transmit FIFO Half Empty Interrupt Flag bit `0` 1: (FIFO configured as a Transmit Buffer) 1 = FIFO is ? half full, 0 = FIFO is > half full `0` 0: (FIFO configured as a Receive Buffer) Unused, reads 0
TXEMPTYIF	8	Transmit FIFO Empty Interrupt Flag bit `0` 1: (FIFO configured as a Transmit Buffer) 1 = FIFO is empty, 0 = FIFO is not empty, at least 1 message queued to be transmitted `0` 0: (FIFO configured as a Receive Buffer) Unused, reads 0
RXOVFLIF	3	Receive FIFO Overflow Interrupt Flag bit `0` 1: (FIFO configured as a Transmit Buffer) Unused, reads 0 `0` 0: (FIFO configured as a Receive Buffer) 1 = Overflow event has occurred, 0 = No overflow event occurred
RXFULLIF	2	Receive FIFO Full Interrupt Flag bit `0` 1: (FIFO configured as a Transmit Buffer) Unused, reads 0 `0` 0: (FIFO configured as a Receive Buffer) 1 = FIFO is full, 0 = FIFO is not full
RXHALFIF	1	Receive FIFO Half Full Interrupt Flag bit `0` 1: (FIFO configured as a Transmit Buffer) Unused, reads 0 `0` 0: (FIFO configured as a Receive Buffer) 1 = FIFO is ? half full, 0 = FIFO is < half full
RXNEMPTYIF	0	Receive Buffer Not Empty Interrupt Flag bit `0` 0: (FIFO configured as a Receive Buffer) 1 = FIFO is not empty, has at least 1 message, 0 = FIFO is empty `1` 1: (FIFO configured as a Transmit Buffer) Unused, reads 0

C1FIFOUA5CAN FIFO User Address Register

Address: 0xBF8804B0
Reset: 0x00000000
Access: read only
Size: 32-bit

C1FIFOCI5CAN Module Message Index Register

Address: 0xBF8804C0
Reset: 0x00000000
Access: read only
Size: 32-bit

1 field

Field	Bits	What it does
CFIFOCI	4:0

C1FIFOCON6CAN FIFO Control Register

Address: 0xBF8804D0
Reset: 0x00000000
Access: read/write
Size: 32-bit

11 fields

Field	Bits	What it does
FSIZE	20:16	FIFO Size bits `0` FIFO is 1 message deep `1` FIFO is 2 messages deep `2` FIFO is 3 messages deep `31` FIFO is 32 messages deep
FRESET	14	FIFO Reset bits `0` No effect `1` FIFO will be reset when bit is set, cleared by hardware when FIFO is reset. After setting, the user application should poll whether this bit is clear before taking any action
UINC	13	Increment Head/Tail bit `0` 1: (FIFO configured as a Transmit FIFO) When this bit is set, the FIFO head will increment by a single message `0` 0: (FIFO configured as a Receive FIFO) When this bit is set, the FIFO tail will increment by a single message
DONLY	12	Store Message Data Only bit `0` 1: (FIFO configured as a Transmit FIFO) This bit is not used and has no effect. `0` 0: (FIFO configured as a Receive FIFO) 1 = Only data bytes will be stored in the FIFO, 0 = Full message is stored, including identifier
TXEN	7	TX/RX Buffer Selection bit `0` FIFO is a Receive FIFO `1` FIFO is a Transmit FIFO
TXABAT	6	Message Aborted bit `0` Message completed successfully `1` Message was aborted
TXLARB	5	Message Lost Arbitration bit `0` Message did not lose arbitration while being sent `1` Message lost arbitration while being sent
TXERR	4	Error Detected During Transmission bit `0` A bus error did not occur while the message was being sent `1` A bus error occurred while the message was being sent
TXREQ	3	Message Send Request `0` 1: (FIFO configured as a Transmit FIFO) Setting this bit to 1 requests sending a message. The bit will automatically clear when all the messages queued in the FIFO are successfully sent. Clearing the bit to 0 while set will request a message abort. `0` 0: (FIFO configured as a Receive FIFO) This bit has no effect.
RTREN	2	Auto RTR Enable bit `0` When a remote transmit is received, TXREQ will be unaffected `1` When a remote transmit is received, TXREQ will be set
TXPRI	1:0	Message Transmit Priority bits `0` Lowest Message Priority `1` Low Intermediate Message Priority `2` High Intermediate Message Priority `3` Highest Message Priority

C1FIFOINT6CAN FIFO Interrupt Register

Address: 0xBF8804E0
Reset: 0x00000000
Access: read/write
Size: 32-bit

14 fields

Field	Bits	What it does
TXNFULLIE	26	Transmit FIFO Not Full Interrupt Enable bit `0` Interrupt disabled for FIFO not full `1` Interrupt enabled for FIFO not full
TXHALFIE	25	Transmit FIFO Half Full Interrupt Enable bit `0` Interrupt disabled for FIFO half full `1` Interrupt enabled for FIFO half full
TXEMPTYIE	24	Transmit FIFO Empty Interrupt Enable bit `0` Interrupt disabled for FIFO empty `1` Interrupt enabled for FIFO empty
RXOVFLIE	19	Overflow Interrupt Enable bit `0` Interrupt disabled for overflow event `1` Interrupt enabled for overflow event
RXFULLIE	18	Full Interrupt Enable bit `0` Interrupt disabled for FIFO full `1` Interrupt enabled for FIFO full
RXHALFIE	17	FIFO Half Full Interrupt Enable bit `0` Interrupt disabled for FIFO half full `1` Interrupt enabled for FIFO half full
RXNEMPTYIE	16	Empty Interrupt Enable bit `0` Interrupt disabled for FIFO not empty `1` Interrupt enabled for FIFO not empty
TXNFULLIF	10	Transmit FIFO Not Full Interrupt Flag bit `0` 1: (FIFO configured as a Transmit Buffer) 1 = FIFO is not full, 0 = FIFO is full `0` 0: (FIFO configured as a Receive Buffer) Unused, reads 0
TXHALFIF	9	FIFO Transmit FIFO Half Empty Interrupt Flag bit `0` 1: (FIFO configured as a Transmit Buffer) 1 = FIFO is ? half full, 0 = FIFO is > half full `0` 0: (FIFO configured as a Receive Buffer) Unused, reads 0
TXEMPTYIF	8	Transmit FIFO Empty Interrupt Flag bit `0` 1: (FIFO configured as a Transmit Buffer) 1 = FIFO is empty, 0 = FIFO is not empty, at least 1 message queued to be transmitted `0` 0: (FIFO configured as a Receive Buffer) Unused, reads 0
RXOVFLIF	3	Receive FIFO Overflow Interrupt Flag bit `0` 1: (FIFO configured as a Transmit Buffer) Unused, reads 0 `0` 0: (FIFO configured as a Receive Buffer) 1 = Overflow event has occurred, 0 = No overflow event occurred
RXFULLIF	2	Receive FIFO Full Interrupt Flag bit `0` 1: (FIFO configured as a Transmit Buffer) Unused, reads 0 `0` 0: (FIFO configured as a Receive Buffer) 1 = FIFO is full, 0 = FIFO is not full
RXHALFIF	1	Receive FIFO Half Full Interrupt Flag bit `0` 1: (FIFO configured as a Transmit Buffer) Unused, reads 0 `0` 0: (FIFO configured as a Receive Buffer) 1 = FIFO is ? half full, 0 = FIFO is < half full
RXNEMPTYIF	0	Receive Buffer Not Empty Interrupt Flag bit `0` 0: (FIFO configured as a Receive Buffer) 1 = FIFO is not empty, has at least 1 message, 0 = FIFO is empty `1` 1: (FIFO configured as a Transmit Buffer) Unused, reads 0

C1FIFOUA6CAN FIFO User Address Register

Address: 0xBF8804F0
Reset: 0x00000000
Access: read only
Size: 32-bit

C1FIFOCI6CAN Module Message Index Register

Address: 0xBF880500
Reset: 0x00000000
Access: read only
Size: 32-bit

1 field

Field	Bits	What it does
CFIFOCI	4:0

C1FIFOCON7CAN FIFO Control Register

Address: 0xBF880510
Reset: 0x00000000
Access: read/write
Size: 32-bit

11 fields

Field	Bits	What it does
FSIZE	20:16	FIFO Size bits `0` FIFO is 1 message deep `1` FIFO is 2 messages deep `2` FIFO is 3 messages deep `31` FIFO is 32 messages deep
FRESET	14	FIFO Reset bits `0` No effect `1` FIFO will be reset when bit is set, cleared by hardware when FIFO is reset. After setting, the user application should poll whether this bit is clear before taking any action
UINC	13	Increment Head/Tail bit `0` 1: (FIFO configured as a Transmit FIFO) When this bit is set, the FIFO head will increment by a single message `0` 0: (FIFO configured as a Receive FIFO) When this bit is set, the FIFO tail will increment by a single message
DONLY	12	Store Message Data Only bit `0` 1: (FIFO configured as a Transmit FIFO) This bit is not used and has no effect. `0` 0: (FIFO configured as a Receive FIFO) 1 = Only data bytes will be stored in the FIFO, 0 = Full message is stored, including identifier
TXEN	7	TX/RX Buffer Selection bit `0` FIFO is a Receive FIFO `1` FIFO is a Transmit FIFO
TXABAT	6	Message Aborted bit `0` Message completed successfully `1` Message was aborted
TXLARB	5	Message Lost Arbitration bit `0` Message did not lose arbitration while being sent `1` Message lost arbitration while being sent
TXERR	4	Error Detected During Transmission bit `0` A bus error did not occur while the message was being sent `1` A bus error occurred while the message was being sent
TXREQ	3	Message Send Request `0` 1: (FIFO configured as a Transmit FIFO) Setting this bit to 1 requests sending a message. The bit will automatically clear when all the messages queued in the FIFO are successfully sent. Clearing the bit to 0 while set will request a message abort. `0` 0: (FIFO configured as a Receive FIFO) This bit has no effect.
RTREN	2	Auto RTR Enable bit `0` When a remote transmit is received, TXREQ will be unaffected `1` When a remote transmit is received, TXREQ will be set
TXPRI	1:0	Message Transmit Priority bits `0` Lowest Message Priority `1` Low Intermediate Message Priority `2` High Intermediate Message Priority `3` Highest Message Priority

C1FIFOINT7CAN FIFO Interrupt Register

Address: 0xBF880520
Reset: 0x00000000
Access: read/write
Size: 32-bit

14 fields

Field	Bits	What it does
TXNFULLIE	26	Transmit FIFO Not Full Interrupt Enable bit `0` Interrupt disabled for FIFO not full `1` Interrupt enabled for FIFO not full
TXHALFIE	25	Transmit FIFO Half Full Interrupt Enable bit `0` Interrupt disabled for FIFO half full `1` Interrupt enabled for FIFO half full
TXEMPTYIE	24	Transmit FIFO Empty Interrupt Enable bit `0` Interrupt disabled for FIFO empty `1` Interrupt enabled for FIFO empty
RXOVFLIE	19	Overflow Interrupt Enable bit `0` Interrupt disabled for overflow event `1` Interrupt enabled for overflow event
RXFULLIE	18	Full Interrupt Enable bit `0` Interrupt disabled for FIFO full `1` Interrupt enabled for FIFO full
RXHALFIE	17	FIFO Half Full Interrupt Enable bit `0` Interrupt disabled for FIFO half full `1` Interrupt enabled for FIFO half full
RXNEMPTYIE	16	Empty Interrupt Enable bit `0` Interrupt disabled for FIFO not empty `1` Interrupt enabled for FIFO not empty
TXNFULLIF	10	Transmit FIFO Not Full Interrupt Flag bit `0` 1: (FIFO configured as a Transmit Buffer) 1 = FIFO is not full, 0 = FIFO is full `0` 0: (FIFO configured as a Receive Buffer) Unused, reads 0
TXHALFIF	9	FIFO Transmit FIFO Half Empty Interrupt Flag bit `0` 1: (FIFO configured as a Transmit Buffer) 1 = FIFO is ? half full, 0 = FIFO is > half full `0` 0: (FIFO configured as a Receive Buffer) Unused, reads 0
TXEMPTYIF	8	Transmit FIFO Empty Interrupt Flag bit `0` 1: (FIFO configured as a Transmit Buffer) 1 = FIFO is empty, 0 = FIFO is not empty, at least 1 message queued to be transmitted `0` 0: (FIFO configured as a Receive Buffer) Unused, reads 0
RXOVFLIF	3	Receive FIFO Overflow Interrupt Flag bit `0` 1: (FIFO configured as a Transmit Buffer) Unused, reads 0 `0` 0: (FIFO configured as a Receive Buffer) 1 = Overflow event has occurred, 0 = No overflow event occurred
RXFULLIF	2	Receive FIFO Full Interrupt Flag bit `0` 1: (FIFO configured as a Transmit Buffer) Unused, reads 0 `0` 0: (FIFO configured as a Receive Buffer) 1 = FIFO is full, 0 = FIFO is not full
RXHALFIF	1	Receive FIFO Half Full Interrupt Flag bit `0` 1: (FIFO configured as a Transmit Buffer) Unused, reads 0 `0` 0: (FIFO configured as a Receive Buffer) 1 = FIFO is ? half full, 0 = FIFO is < half full
RXNEMPTYIF	0	Receive Buffer Not Empty Interrupt Flag bit `0` 0: (FIFO configured as a Receive Buffer) 1 = FIFO is not empty, has at least 1 message, 0 = FIFO is empty `1` 1: (FIFO configured as a Transmit Buffer) Unused, reads 0

C1FIFOUA7CAN FIFO User Address Register

Address: 0xBF880530
Reset: 0x00000000
Access: read only
Size: 32-bit

C1FIFOCI7CAN Module Message Index Register

Address: 0xBF880540
Reset: 0x00000000
Access: read only
Size: 32-bit

1 field

Field	Bits	What it does
CFIFOCI	4:0

C1FIFOCON8CAN FIFO Control Register

Address: 0xBF880550
Reset: 0x00000000
Access: read/write
Size: 32-bit

11 fields

Field	Bits	What it does
FSIZE	20:16	FIFO Size bits `0` FIFO is 1 message deep `1` FIFO is 2 messages deep `2` FIFO is 3 messages deep `31` FIFO is 32 messages deep
FRESET	14	FIFO Reset bits `0` No effect `1` FIFO will be reset when bit is set, cleared by hardware when FIFO is reset. After setting, the user application should poll whether this bit is clear before taking any action
UINC	13	Increment Head/Tail bit `0` 1: (FIFO configured as a Transmit FIFO) When this bit is set, the FIFO head will increment by a single message `0` 0: (FIFO configured as a Receive FIFO) When this bit is set, the FIFO tail will increment by a single message
DONLY	12	Store Message Data Only bit `0` 1: (FIFO configured as a Transmit FIFO) This bit is not used and has no effect. `0` 0: (FIFO configured as a Receive FIFO) 1 = Only data bytes will be stored in the FIFO, 0 = Full message is stored, including identifier
TXEN	7	TX/RX Buffer Selection bit `0` FIFO is a Receive FIFO `1` FIFO is a Transmit FIFO
TXABAT	6	Message Aborted bit `0` Message completed successfully `1` Message was aborted
TXLARB	5	Message Lost Arbitration bit `0` Message did not lose arbitration while being sent `1` Message lost arbitration while being sent
TXERR	4	Error Detected During Transmission bit `0` A bus error did not occur while the message was being sent `1` A bus error occurred while the message was being sent
TXREQ	3	Message Send Request `0` 1: (FIFO configured as a Transmit FIFO) Setting this bit to 1 requests sending a message. The bit will automatically clear when all the messages queued in the FIFO are successfully sent. Clearing the bit to 0 while set will request a message abort. `0` 0: (FIFO configured as a Receive FIFO) This bit has no effect.
RTREN	2	Auto RTR Enable bit `0` When a remote transmit is received, TXREQ will be unaffected `1` When a remote transmit is received, TXREQ will be set
TXPRI	1:0	Message Transmit Priority bits `0` Lowest Message Priority `1` Low Intermediate Message Priority `2` High Intermediate Message Priority `3` Highest Message Priority

C1FIFOINT8CAN FIFO Interrupt Register

Address: 0xBF880560
Reset: 0x00000000
Access: read/write
Size: 32-bit

14 fields

Field	Bits	What it does
TXNFULLIE	26	Transmit FIFO Not Full Interrupt Enable bit `0` Interrupt disabled for FIFO not full `1` Interrupt enabled for FIFO not full
TXHALFIE	25	Transmit FIFO Half Full Interrupt Enable bit `0` Interrupt disabled for FIFO half full `1` Interrupt enabled for FIFO half full
TXEMPTYIE	24	Transmit FIFO Empty Interrupt Enable bit `0` Interrupt disabled for FIFO empty `1` Interrupt enabled for FIFO empty
RXOVFLIE	19	Overflow Interrupt Enable bit `0` Interrupt disabled for overflow event `1` Interrupt enabled for overflow event
RXFULLIE	18	Full Interrupt Enable bit `0` Interrupt disabled for FIFO full `1` Interrupt enabled for FIFO full
RXHALFIE	17	FIFO Half Full Interrupt Enable bit `0` Interrupt disabled for FIFO half full `1` Interrupt enabled for FIFO half full
RXNEMPTYIE	16	Empty Interrupt Enable bit `0` Interrupt disabled for FIFO not empty `1` Interrupt enabled for FIFO not empty
TXNFULLIF	10	Transmit FIFO Not Full Interrupt Flag bit `0` 1: (FIFO configured as a Transmit Buffer) 1 = FIFO is not full, 0 = FIFO is full `0` 0: (FIFO configured as a Receive Buffer) Unused, reads 0
TXHALFIF	9	FIFO Transmit FIFO Half Empty Interrupt Flag bit `0` 1: (FIFO configured as a Transmit Buffer) 1 = FIFO is ? half full, 0 = FIFO is > half full `0` 0: (FIFO configured as a Receive Buffer) Unused, reads 0
TXEMPTYIF	8	Transmit FIFO Empty Interrupt Flag bit `0` 1: (FIFO configured as a Transmit Buffer) 1 = FIFO is empty, 0 = FIFO is not empty, at least 1 message queued to be transmitted `0` 0: (FIFO configured as a Receive Buffer) Unused, reads 0
RXOVFLIF	3	Receive FIFO Overflow Interrupt Flag bit `0` 1: (FIFO configured as a Transmit Buffer) Unused, reads 0 `0` 0: (FIFO configured as a Receive Buffer) 1 = Overflow event has occurred, 0 = No overflow event occurred
RXFULLIF	2	Receive FIFO Full Interrupt Flag bit `0` 1: (FIFO configured as a Transmit Buffer) Unused, reads 0 `0` 0: (FIFO configured as a Receive Buffer) 1 = FIFO is full, 0 = FIFO is not full
RXHALFIF	1	Receive FIFO Half Full Interrupt Flag bit `0` 1: (FIFO configured as a Transmit Buffer) Unused, reads 0 `0` 0: (FIFO configured as a Receive Buffer) 1 = FIFO is ? half full, 0 = FIFO is < half full
RXNEMPTYIF	0	Receive Buffer Not Empty Interrupt Flag bit `0` 0: (FIFO configured as a Receive Buffer) 1 = FIFO is not empty, has at least 1 message, 0 = FIFO is empty `1` 1: (FIFO configured as a Transmit Buffer) Unused, reads 0

C1FIFOUA8CAN FIFO User Address Register

Address: 0xBF880570
Reset: 0x00000000
Access: read only
Size: 32-bit

C1FIFOCI8CAN Module Message Index Register

Address: 0xBF880580
Reset: 0x00000000
Access: read only
Size: 32-bit

1 field

Field	Bits	What it does
CFIFOCI	4:0

C1FIFOCON9CAN FIFO Control Register

Address: 0xBF880590
Reset: 0x00000000
Access: read/write
Size: 32-bit

11 fields

Field	Bits	What it does
FSIZE	20:16	FIFO Size bits `0` FIFO is 1 message deep `1` FIFO is 2 messages deep `2` FIFO is 3 messages deep `31` FIFO is 32 messages deep
FRESET	14	FIFO Reset bits `0` No effect `1` FIFO will be reset when bit is set, cleared by hardware when FIFO is reset. After setting, the user application should poll whether this bit is clear before taking any action
UINC	13	Increment Head/Tail bit `0` 1: (FIFO configured as a Transmit FIFO) When this bit is set, the FIFO head will increment by a single message `0` 0: (FIFO configured as a Receive FIFO) When this bit is set, the FIFO tail will increment by a single message
DONLY	12	Store Message Data Only bit `0` 1: (FIFO configured as a Transmit FIFO) This bit is not used and has no effect. `0` 0: (FIFO configured as a Receive FIFO) 1 = Only data bytes will be stored in the FIFO, 0 = Full message is stored, including identifier
TXEN	7	TX/RX Buffer Selection bit `0` FIFO is a Receive FIFO `1` FIFO is a Transmit FIFO
TXABAT	6	Message Aborted bit `0` Message completed successfully `1` Message was aborted
TXLARB	5	Message Lost Arbitration bit `0` Message did not lose arbitration while being sent `1` Message lost arbitration while being sent
TXERR	4	Error Detected During Transmission bit `0` A bus error did not occur while the message was being sent `1` A bus error occurred while the message was being sent
TXREQ	3	Message Send Request `0` 1: (FIFO configured as a Transmit FIFO) Setting this bit to 1 requests sending a message. The bit will automatically clear when all the messages queued in the FIFO are successfully sent. Clearing the bit to 0 while set will request a message abort. `0` 0: (FIFO configured as a Receive FIFO) This bit has no effect.
RTREN	2	Auto RTR Enable bit `0` When a remote transmit is received, TXREQ will be unaffected `1` When a remote transmit is received, TXREQ will be set
TXPRI	1:0	Message Transmit Priority bits `0` Lowest Message Priority `1` Low Intermediate Message Priority `2` High Intermediate Message Priority `3` Highest Message Priority

C1FIFOINT9CAN FIFO Interrupt Register

Address: 0xBF8805A0
Reset: 0x00000000
Access: read/write
Size: 32-bit

14 fields

Field	Bits	What it does
TXNFULLIE	26	Transmit FIFO Not Full Interrupt Enable bit `0` Interrupt disabled for FIFO not full `1` Interrupt enabled for FIFO not full
TXHALFIE	25	Transmit FIFO Half Full Interrupt Enable bit `0` Interrupt disabled for FIFO half full `1` Interrupt enabled for FIFO half full
TXEMPTYIE	24	Transmit FIFO Empty Interrupt Enable bit `0` Interrupt disabled for FIFO empty `1` Interrupt enabled for FIFO empty
RXOVFLIE	19	Overflow Interrupt Enable bit `0` Interrupt disabled for overflow event `1` Interrupt enabled for overflow event
RXFULLIE	18	Full Interrupt Enable bit `0` Interrupt disabled for FIFO full `1` Interrupt enabled for FIFO full
RXHALFIE	17	FIFO Half Full Interrupt Enable bit `0` Interrupt disabled for FIFO half full `1` Interrupt enabled for FIFO half full
RXNEMPTYIE	16	Empty Interrupt Enable bit `0` Interrupt disabled for FIFO not empty `1` Interrupt enabled for FIFO not empty
TXNFULLIF	10	Transmit FIFO Not Full Interrupt Flag bit `0` 1: (FIFO configured as a Transmit Buffer) 1 = FIFO is not full, 0 = FIFO is full `0` 0: (FIFO configured as a Receive Buffer) Unused, reads 0
TXHALFIF	9	FIFO Transmit FIFO Half Empty Interrupt Flag bit `0` 1: (FIFO configured as a Transmit Buffer) 1 = FIFO is ? half full, 0 = FIFO is > half full `0` 0: (FIFO configured as a Receive Buffer) Unused, reads 0
TXEMPTYIF	8	Transmit FIFO Empty Interrupt Flag bit `0` 1: (FIFO configured as a Transmit Buffer) 1 = FIFO is empty, 0 = FIFO is not empty, at least 1 message queued to be transmitted `0` 0: (FIFO configured as a Receive Buffer) Unused, reads 0
RXOVFLIF	3	Receive FIFO Overflow Interrupt Flag bit `0` 1: (FIFO configured as a Transmit Buffer) Unused, reads 0 `0` 0: (FIFO configured as a Receive Buffer) 1 = Overflow event has occurred, 0 = No overflow event occurred
RXFULLIF	2	Receive FIFO Full Interrupt Flag bit `0` 1: (FIFO configured as a Transmit Buffer) Unused, reads 0 `0` 0: (FIFO configured as a Receive Buffer) 1 = FIFO is full, 0 = FIFO is not full
RXHALFIF	1	Receive FIFO Half Full Interrupt Flag bit `0` 1: (FIFO configured as a Transmit Buffer) Unused, reads 0 `0` 0: (FIFO configured as a Receive Buffer) 1 = FIFO is ? half full, 0 = FIFO is < half full
RXNEMPTYIF	0	Receive Buffer Not Empty Interrupt Flag bit `0` 0: (FIFO configured as a Receive Buffer) 1 = FIFO is not empty, has at least 1 message, 0 = FIFO is empty `1` 1: (FIFO configured as a Transmit Buffer) Unused, reads 0

C1FIFOUA9CAN FIFO User Address Register

Address: 0xBF8805B0
Reset: 0x00000000
Access: read only
Size: 32-bit

C1FIFOCI9CAN Module Message Index Register

Address: 0xBF8805C0
Reset: 0x00000000
Access: read only
Size: 32-bit

1 field

Field	Bits	What it does
CFIFOCI	4:0

C1FIFOCON10CAN FIFO Control Register

Address: 0xBF8805D0
Reset: 0x00000000
Access: read/write
Size: 32-bit

11 fields

Field	Bits	What it does
FSIZE	20:16	FIFO Size bits `0` FIFO is 1 message deep `1` FIFO is 2 messages deep `2` FIFO is 3 messages deep `31` FIFO is 32 messages deep
FRESET	14	FIFO Reset bits `0` No effect `1` FIFO will be reset when bit is set, cleared by hardware when FIFO is reset. After setting, the user application should poll whether this bit is clear before taking any action
UINC	13	Increment Head/Tail bit `0` 1: (FIFO configured as a Transmit FIFO) When this bit is set, the FIFO head will increment by a single message `0` 0: (FIFO configured as a Receive FIFO) When this bit is set, the FIFO tail will increment by a single message
DONLY	12	Store Message Data Only bit `0` 1: (FIFO configured as a Transmit FIFO) This bit is not used and has no effect. `0` 0: (FIFO configured as a Receive FIFO) 1 = Only data bytes will be stored in the FIFO, 0 = Full message is stored, including identifier
TXEN	7	TX/RX Buffer Selection bit `0` FIFO is a Receive FIFO `1` FIFO is a Transmit FIFO
TXABAT	6	Message Aborted bit `0` Message completed successfully `1` Message was aborted
TXLARB	5	Message Lost Arbitration bit `0` Message did not lose arbitration while being sent `1` Message lost arbitration while being sent
TXERR	4	Error Detected During Transmission bit `0` A bus error did not occur while the message was being sent `1` A bus error occurred while the message was being sent
TXREQ	3	Message Send Request `0` 1: (FIFO configured as a Transmit FIFO) Setting this bit to 1 requests sending a message. The bit will automatically clear when all the messages queued in the FIFO are successfully sent. Clearing the bit to 0 while set will request a message abort. `0` 0: (FIFO configured as a Receive FIFO) This bit has no effect.
RTREN	2	Auto RTR Enable bit `0` When a remote transmit is received, TXREQ will be unaffected `1` When a remote transmit is received, TXREQ will be set
TXPRI	1:0	Message Transmit Priority bits `0` Lowest Message Priority `1` Low Intermediate Message Priority `2` High Intermediate Message Priority `3` Highest Message Priority

C1FIFOINT10CAN FIFO Interrupt Register

Address: 0xBF8805E0
Reset: 0x00000000
Access: read/write
Size: 32-bit

14 fields

Field	Bits	What it does
TXNFULLIE	26	Transmit FIFO Not Full Interrupt Enable bit `0` Interrupt disabled for FIFO not full `1` Interrupt enabled for FIFO not full
TXHALFIE	25	Transmit FIFO Half Full Interrupt Enable bit `0` Interrupt disabled for FIFO half full `1` Interrupt enabled for FIFO half full
TXEMPTYIE	24	Transmit FIFO Empty Interrupt Enable bit `0` Interrupt disabled for FIFO empty `1` Interrupt enabled for FIFO empty
RXOVFLIE	19	Overflow Interrupt Enable bit `0` Interrupt disabled for overflow event `1` Interrupt enabled for overflow event
RXFULLIE	18	Full Interrupt Enable bit `0` Interrupt disabled for FIFO full `1` Interrupt enabled for FIFO full
RXHALFIE	17	FIFO Half Full Interrupt Enable bit `0` Interrupt disabled for FIFO half full `1` Interrupt enabled for FIFO half full
RXNEMPTYIE	16	Empty Interrupt Enable bit `0` Interrupt disabled for FIFO not empty `1` Interrupt enabled for FIFO not empty
TXNFULLIF	10	Transmit FIFO Not Full Interrupt Flag bit `0` 1: (FIFO configured as a Transmit Buffer) 1 = FIFO is not full, 0 = FIFO is full `0` 0: (FIFO configured as a Receive Buffer) Unused, reads 0
TXHALFIF	9	FIFO Transmit FIFO Half Empty Interrupt Flag bit `0` 1: (FIFO configured as a Transmit Buffer) 1 = FIFO is ? half full, 0 = FIFO is > half full `0` 0: (FIFO configured as a Receive Buffer) Unused, reads 0
TXEMPTYIF	8	Transmit FIFO Empty Interrupt Flag bit `0` 1: (FIFO configured as a Transmit Buffer) 1 = FIFO is empty, 0 = FIFO is not empty, at least 1 message queued to be transmitted `0` 0: (FIFO configured as a Receive Buffer) Unused, reads 0
RXOVFLIF	3	Receive FIFO Overflow Interrupt Flag bit `0` 1: (FIFO configured as a Transmit Buffer) Unused, reads 0 `0` 0: (FIFO configured as a Receive Buffer) 1 = Overflow event has occurred, 0 = No overflow event occurred
RXFULLIF	2	Receive FIFO Full Interrupt Flag bit `0` 1: (FIFO configured as a Transmit Buffer) Unused, reads 0 `0` 0: (FIFO configured as a Receive Buffer) 1 = FIFO is full, 0 = FIFO is not full
RXHALFIF	1	Receive FIFO Half Full Interrupt Flag bit `0` 1: (FIFO configured as a Transmit Buffer) Unused, reads 0 `0` 0: (FIFO configured as a Receive Buffer) 1 = FIFO is ? half full, 0 = FIFO is < half full
RXNEMPTYIF	0	Receive Buffer Not Empty Interrupt Flag bit `0` 0: (FIFO configured as a Receive Buffer) 1 = FIFO is not empty, has at least 1 message, 0 = FIFO is empty `1` 1: (FIFO configured as a Transmit Buffer) Unused, reads 0

C1FIFOUA10CAN FIFO User Address Register

Address: 0xBF8805F0
Reset: 0x00000000
Access: read only
Size: 32-bit

C1FIFOCI10CAN Module Message Index Register

Address: 0xBF880600
Reset: 0x00000000
Access: read only
Size: 32-bit

1 field

Field	Bits	What it does
CFIFOCI	4:0

C1FIFOCON11CAN FIFO Control Register

Address: 0xBF880610
Reset: 0x00000000
Access: read/write
Size: 32-bit

11 fields

Field	Bits	What it does
FSIZE	20:16	FIFO Size bits `0` FIFO is 1 message deep `1` FIFO is 2 messages deep `2` FIFO is 3 messages deep `31` FIFO is 32 messages deep
FRESET	14	FIFO Reset bits `0` No effect `1` FIFO will be reset when bit is set, cleared by hardware when FIFO is reset. After setting, the user application should poll whether this bit is clear before taking any action
UINC	13	Increment Head/Tail bit `0` 1: (FIFO configured as a Transmit FIFO) When this bit is set, the FIFO head will increment by a single message `0` 0: (FIFO configured as a Receive FIFO) When this bit is set, the FIFO tail will increment by a single message
DONLY	12	Store Message Data Only bit `0` 1: (FIFO configured as a Transmit FIFO) This bit is not used and has no effect. `0` 0: (FIFO configured as a Receive FIFO) 1 = Only data bytes will be stored in the FIFO, 0 = Full message is stored, including identifier
TXEN	7	TX/RX Buffer Selection bit `0` FIFO is a Receive FIFO `1` FIFO is a Transmit FIFO
TXABAT	6	Message Aborted bit `0` Message completed successfully `1` Message was aborted
TXLARB	5	Message Lost Arbitration bit `0` Message did not lose arbitration while being sent `1` Message lost arbitration while being sent
TXERR	4	Error Detected During Transmission bit `0` A bus error did not occur while the message was being sent `1` A bus error occurred while the message was being sent
TXREQ	3	Message Send Request `0` 1: (FIFO configured as a Transmit FIFO) Setting this bit to 1 requests sending a message. The bit will automatically clear when all the messages queued in the FIFO are successfully sent. Clearing the bit to 0 while set will request a message abort. `0` 0: (FIFO configured as a Receive FIFO) This bit has no effect.
RTREN	2	Auto RTR Enable bit `0` When a remote transmit is received, TXREQ will be unaffected `1` When a remote transmit is received, TXREQ will be set
TXPRI	1:0	Message Transmit Priority bits `0` Lowest Message Priority `1` Low Intermediate Message Priority `2` High Intermediate Message Priority `3` Highest Message Priority

C1FIFOINT11CAN FIFO Interrupt Register

Address: 0xBF880620
Reset: 0x00000000
Access: read/write
Size: 32-bit

14 fields

Field	Bits	What it does
TXNFULLIE	26	Transmit FIFO Not Full Interrupt Enable bit `0` Interrupt disabled for FIFO not full `1` Interrupt enabled for FIFO not full
TXHALFIE	25	Transmit FIFO Half Full Interrupt Enable bit `0` Interrupt disabled for FIFO half full `1` Interrupt enabled for FIFO half full
TXEMPTYIE	24	Transmit FIFO Empty Interrupt Enable bit `0` Interrupt disabled for FIFO empty `1` Interrupt enabled for FIFO empty
RXOVFLIE	19	Overflow Interrupt Enable bit `0` Interrupt disabled for overflow event `1` Interrupt enabled for overflow event
RXFULLIE	18	Full Interrupt Enable bit `0` Interrupt disabled for FIFO full `1` Interrupt enabled for FIFO full
RXHALFIE	17	FIFO Half Full Interrupt Enable bit `0` Interrupt disabled for FIFO half full `1` Interrupt enabled for FIFO half full
RXNEMPTYIE	16	Empty Interrupt Enable bit `0` Interrupt disabled for FIFO not empty `1` Interrupt enabled for FIFO not empty
TXNFULLIF	10	Transmit FIFO Not Full Interrupt Flag bit `0` 1: (FIFO configured as a Transmit Buffer) 1 = FIFO is not full, 0 = FIFO is full `0` 0: (FIFO configured as a Receive Buffer) Unused, reads 0
TXHALFIF	9	FIFO Transmit FIFO Half Empty Interrupt Flag bit `0` 1: (FIFO configured as a Transmit Buffer) 1 = FIFO is ? half full, 0 = FIFO is > half full `0` 0: (FIFO configured as a Receive Buffer) Unused, reads 0
TXEMPTYIF	8	Transmit FIFO Empty Interrupt Flag bit `0` 1: (FIFO configured as a Transmit Buffer) 1 = FIFO is empty, 0 = FIFO is not empty, at least 1 message queued to be transmitted `0` 0: (FIFO configured as a Receive Buffer) Unused, reads 0
RXOVFLIF	3	Receive FIFO Overflow Interrupt Flag bit `0` 1: (FIFO configured as a Transmit Buffer) Unused, reads 0 `0` 0: (FIFO configured as a Receive Buffer) 1 = Overflow event has occurred, 0 = No overflow event occurred
RXFULLIF	2	Receive FIFO Full Interrupt Flag bit `0` 1: (FIFO configured as a Transmit Buffer) Unused, reads 0 `0` 0: (FIFO configured as a Receive Buffer) 1 = FIFO is full, 0 = FIFO is not full
RXHALFIF	1	Receive FIFO Half Full Interrupt Flag bit `0` 1: (FIFO configured as a Transmit Buffer) Unused, reads 0 `0` 0: (FIFO configured as a Receive Buffer) 1 = FIFO is ? half full, 0 = FIFO is < half full
RXNEMPTYIF	0	Receive Buffer Not Empty Interrupt Flag bit `0` 0: (FIFO configured as a Receive Buffer) 1 = FIFO is not empty, has at least 1 message, 0 = FIFO is empty `1` 1: (FIFO configured as a Transmit Buffer) Unused, reads 0

C1FIFOUA11CAN FIFO User Address Register

Address: 0xBF880630
Reset: 0x00000000
Access: read only
Size: 32-bit

C1FIFOCI11CAN Module Message Index Register

Address: 0xBF880640
Reset: 0x00000000
Access: read only
Size: 32-bit

1 field

Field	Bits	What it does
CFIFOCI	4:0

C1FIFOCON12CAN FIFO Control Register

Address: 0xBF880650
Reset: 0x00000000
Access: read/write
Size: 32-bit

11 fields

Field	Bits	What it does
FSIZE	20:16	FIFO Size bits `0` FIFO is 1 message deep `1` FIFO is 2 messages deep `2` FIFO is 3 messages deep `31` FIFO is 32 messages deep
FRESET	14	FIFO Reset bits `0` No effect `1` FIFO will be reset when bit is set, cleared by hardware when FIFO is reset. After setting, the user application should poll whether this bit is clear before taking any action
UINC	13	Increment Head/Tail bit `0` 1: (FIFO configured as a Transmit FIFO) When this bit is set, the FIFO head will increment by a single message `0` 0: (FIFO configured as a Receive FIFO) When this bit is set, the FIFO tail will increment by a single message
DONLY	12	Store Message Data Only bit `0` 1: (FIFO configured as a Transmit FIFO) This bit is not used and has no effect. `0` 0: (FIFO configured as a Receive FIFO) 1 = Only data bytes will be stored in the FIFO, 0 = Full message is stored, including identifier
TXEN	7	TX/RX Buffer Selection bit `0` FIFO is a Receive FIFO `1` FIFO is a Transmit FIFO
TXABAT	6	Message Aborted bit `0` Message completed successfully `1` Message was aborted
TXLARB	5	Message Lost Arbitration bit `0` Message did not lose arbitration while being sent `1` Message lost arbitration while being sent
TXERR	4	Error Detected During Transmission bit `0` A bus error did not occur while the message was being sent `1` A bus error occurred while the message was being sent
TXREQ	3	Message Send Request `0` 1: (FIFO configured as a Transmit FIFO) Setting this bit to 1 requests sending a message. The bit will automatically clear when all the messages queued in the FIFO are successfully sent. Clearing the bit to 0 while set will request a message abort. `0` 0: (FIFO configured as a Receive FIFO) This bit has no effect.
RTREN	2	Auto RTR Enable bit `0` When a remote transmit is received, TXREQ will be unaffected `1` When a remote transmit is received, TXREQ will be set
TXPRI	1:0	Message Transmit Priority bits `0` Lowest Message Priority `1` Low Intermediate Message Priority `2` High Intermediate Message Priority `3` Highest Message Priority

C1FIFOINT12CAN FIFO Interrupt Register

Address: 0xBF880660
Reset: 0x00000000
Access: read/write
Size: 32-bit

14 fields

Field	Bits	What it does
TXNFULLIE	26	Transmit FIFO Not Full Interrupt Enable bit `0` Interrupt disabled for FIFO not full `1` Interrupt enabled for FIFO not full
TXHALFIE	25	Transmit FIFO Half Full Interrupt Enable bit `0` Interrupt disabled for FIFO half full `1` Interrupt enabled for FIFO half full
TXEMPTYIE	24	Transmit FIFO Empty Interrupt Enable bit `0` Interrupt disabled for FIFO empty `1` Interrupt enabled for FIFO empty
RXOVFLIE	19	Overflow Interrupt Enable bit `0` Interrupt disabled for overflow event `1` Interrupt enabled for overflow event
RXFULLIE	18	Full Interrupt Enable bit `0` Interrupt disabled for FIFO full `1` Interrupt enabled for FIFO full
RXHALFIE	17	FIFO Half Full Interrupt Enable bit `0` Interrupt disabled for FIFO half full `1` Interrupt enabled for FIFO half full
RXNEMPTYIE	16	Empty Interrupt Enable bit `0` Interrupt disabled for FIFO not empty `1` Interrupt enabled for FIFO not empty
TXNFULLIF	10	Transmit FIFO Not Full Interrupt Flag bit `0` 1: (FIFO configured as a Transmit Buffer) 1 = FIFO is not full, 0 = FIFO is full `0` 0: (FIFO configured as a Receive Buffer) Unused, reads 0
TXHALFIF	9	FIFO Transmit FIFO Half Empty Interrupt Flag bit `0` 1: (FIFO configured as a Transmit Buffer) 1 = FIFO is ? half full, 0 = FIFO is > half full `0` 0: (FIFO configured as a Receive Buffer) Unused, reads 0
TXEMPTYIF	8	Transmit FIFO Empty Interrupt Flag bit `0` 1: (FIFO configured as a Transmit Buffer) 1 = FIFO is empty, 0 = FIFO is not empty, at least 1 message queued to be transmitted `0` 0: (FIFO configured as a Receive Buffer) Unused, reads 0
RXOVFLIF	3	Receive FIFO Overflow Interrupt Flag bit `0` 1: (FIFO configured as a Transmit Buffer) Unused, reads 0 `0` 0: (FIFO configured as a Receive Buffer) 1 = Overflow event has occurred, 0 = No overflow event occurred
RXFULLIF	2	Receive FIFO Full Interrupt Flag bit `0` 1: (FIFO configured as a Transmit Buffer) Unused, reads 0 `0` 0: (FIFO configured as a Receive Buffer) 1 = FIFO is full, 0 = FIFO is not full
RXHALFIF	1	Receive FIFO Half Full Interrupt Flag bit `0` 1: (FIFO configured as a Transmit Buffer) Unused, reads 0 `0` 0: (FIFO configured as a Receive Buffer) 1 = FIFO is ? half full, 0 = FIFO is < half full
RXNEMPTYIF	0	Receive Buffer Not Empty Interrupt Flag bit `0` 0: (FIFO configured as a Receive Buffer) 1 = FIFO is not empty, has at least 1 message, 0 = FIFO is empty `1` 1: (FIFO configured as a Transmit Buffer) Unused, reads 0

C1FIFOUA12CAN FIFO User Address Register

Address: 0xBF880670
Reset: 0x00000000
Access: read only
Size: 32-bit

C1FIFOCI12CAN Module Message Index Register

Address: 0xBF880680
Reset: 0x00000000
Access: read only
Size: 32-bit

1 field

Field	Bits	What it does
CFIFOCI	4:0

C1FIFOCON13CAN FIFO Control Register

Address: 0xBF880690
Reset: 0x00000000
Access: read/write
Size: 32-bit

11 fields

Field	Bits	What it does
FSIZE	20:16	FIFO Size bits `0` FIFO is 1 message deep `1` FIFO is 2 messages deep `2` FIFO is 3 messages deep `31` FIFO is 32 messages deep
FRESET	14	FIFO Reset bits `0` No effect `1` FIFO will be reset when bit is set, cleared by hardware when FIFO is reset. After setting, the user application should poll whether this bit is clear before taking any action
UINC	13	Increment Head/Tail bit `0` 1: (FIFO configured as a Transmit FIFO) When this bit is set, the FIFO head will increment by a single message `0` 0: (FIFO configured as a Receive FIFO) When this bit is set, the FIFO tail will increment by a single message
DONLY	12	Store Message Data Only bit `0` 1: (FIFO configured as a Transmit FIFO) This bit is not used and has no effect. `0` 0: (FIFO configured as a Receive FIFO) 1 = Only data bytes will be stored in the FIFO, 0 = Full message is stored, including identifier
TXEN	7	TX/RX Buffer Selection bit `0` FIFO is a Receive FIFO `1` FIFO is a Transmit FIFO
TXABAT	6	Message Aborted bit `0` Message completed successfully `1` Message was aborted
TXLARB	5	Message Lost Arbitration bit `0` Message did not lose arbitration while being sent `1` Message lost arbitration while being sent
TXERR	4	Error Detected During Transmission bit `0` A bus error did not occur while the message was being sent `1` A bus error occurred while the message was being sent
TXREQ	3	Message Send Request `0` 1: (FIFO configured as a Transmit FIFO) Setting this bit to 1 requests sending a message. The bit will automatically clear when all the messages queued in the FIFO are successfully sent. Clearing the bit to 0 while set will request a message abort. `0` 0: (FIFO configured as a Receive FIFO) This bit has no effect.
RTREN	2	Auto RTR Enable bit `0` When a remote transmit is received, TXREQ will be unaffected `1` When a remote transmit is received, TXREQ will be set
TXPRI	1:0	Message Transmit Priority bits `0` Lowest Message Priority `1` Low Intermediate Message Priority `2` High Intermediate Message Priority `3` Highest Message Priority

C1FIFOINT13CAN FIFO Interrupt Register

Address: 0xBF8806A0
Reset: 0x00000000
Access: read/write
Size: 32-bit

14 fields

Field	Bits	What it does
TXNFULLIE	26	Transmit FIFO Not Full Interrupt Enable bit `0` Interrupt disabled for FIFO not full `1` Interrupt enabled for FIFO not full
TXHALFIE	25	Transmit FIFO Half Full Interrupt Enable bit `0` Interrupt disabled for FIFO half full `1` Interrupt enabled for FIFO half full
TXEMPTYIE	24	Transmit FIFO Empty Interrupt Enable bit `0` Interrupt disabled for FIFO empty `1` Interrupt enabled for FIFO empty
RXOVFLIE	19	Overflow Interrupt Enable bit `0` Interrupt disabled for overflow event `1` Interrupt enabled for overflow event
RXFULLIE	18	Full Interrupt Enable bit `0` Interrupt disabled for FIFO full `1` Interrupt enabled for FIFO full
RXHALFIE	17	FIFO Half Full Interrupt Enable bit `0` Interrupt disabled for FIFO half full `1` Interrupt enabled for FIFO half full
RXNEMPTYIE	16	Empty Interrupt Enable bit `0` Interrupt disabled for FIFO not empty `1` Interrupt enabled for FIFO not empty
TXNFULLIF	10	Transmit FIFO Not Full Interrupt Flag bit `0` 1: (FIFO configured as a Transmit Buffer) 1 = FIFO is not full, 0 = FIFO is full `0` 0: (FIFO configured as a Receive Buffer) Unused, reads 0
TXHALFIF	9	FIFO Transmit FIFO Half Empty Interrupt Flag bit `0` 1: (FIFO configured as a Transmit Buffer) 1 = FIFO is ? half full, 0 = FIFO is > half full `0` 0: (FIFO configured as a Receive Buffer) Unused, reads 0
TXEMPTYIF	8	Transmit FIFO Empty Interrupt Flag bit `0` 1: (FIFO configured as a Transmit Buffer) 1 = FIFO is empty, 0 = FIFO is not empty, at least 1 message queued to be transmitted `0` 0: (FIFO configured as a Receive Buffer) Unused, reads 0
RXOVFLIF	3	Receive FIFO Overflow Interrupt Flag bit `0` 1: (FIFO configured as a Transmit Buffer) Unused, reads 0 `0` 0: (FIFO configured as a Receive Buffer) 1 = Overflow event has occurred, 0 = No overflow event occurred
RXFULLIF	2	Receive FIFO Full Interrupt Flag bit `0` 1: (FIFO configured as a Transmit Buffer) Unused, reads 0 `0` 0: (FIFO configured as a Receive Buffer) 1 = FIFO is full, 0 = FIFO is not full
RXHALFIF	1	Receive FIFO Half Full Interrupt Flag bit `0` 1: (FIFO configured as a Transmit Buffer) Unused, reads 0 `0` 0: (FIFO configured as a Receive Buffer) 1 = FIFO is ? half full, 0 = FIFO is < half full
RXNEMPTYIF	0	Receive Buffer Not Empty Interrupt Flag bit `0` 0: (FIFO configured as a Receive Buffer) 1 = FIFO is not empty, has at least 1 message, 0 = FIFO is empty `1` 1: (FIFO configured as a Transmit Buffer) Unused, reads 0

C1FIFOUA13CAN FIFO User Address Register

Address: 0xBF8806B0
Reset: 0x00000000
Access: read only
Size: 32-bit

C1FIFOCI13CAN Module Message Index Register

Address: 0xBF8806C0
Reset: 0x00000000
Access: read only
Size: 32-bit

1 field

Field	Bits	What it does
CFIFOCI	4:0

C1FIFOCON14CAN FIFO Control Register

Address: 0xBF8806D0
Reset: 0x00000000
Access: read/write
Size: 32-bit

11 fields

Field	Bits	What it does
FSIZE	20:16	FIFO Size bits `0` FIFO is 1 message deep `1` FIFO is 2 messages deep `2` FIFO is 3 messages deep `31` FIFO is 32 messages deep
FRESET	14	FIFO Reset bits `0` No effect `1` FIFO will be reset when bit is set, cleared by hardware when FIFO is reset. After setting, the user application should poll whether this bit is clear before taking any action
UINC	13	Increment Head/Tail bit `0` 1: (FIFO configured as a Transmit FIFO) When this bit is set, the FIFO head will increment by a single message `0` 0: (FIFO configured as a Receive FIFO) When this bit is set, the FIFO tail will increment by a single message
DONLY	12	Store Message Data Only bit `0` 1: (FIFO configured as a Transmit FIFO) This bit is not used and has no effect. `0` 0: (FIFO configured as a Receive FIFO) 1 = Only data bytes will be stored in the FIFO, 0 = Full message is stored, including identifier
TXEN	7	TX/RX Buffer Selection bit `0` FIFO is a Receive FIFO `1` FIFO is a Transmit FIFO
TXABAT	6	Message Aborted bit `0` Message completed successfully `1` Message was aborted
TXLARB	5	Message Lost Arbitration bit `0` Message did not lose arbitration while being sent `1` Message lost arbitration while being sent
TXERR	4	Error Detected During Transmission bit `0` A bus error did not occur while the message was being sent `1` A bus error occurred while the message was being sent
TXREQ	3	Message Send Request `0` 1: (FIFO configured as a Transmit FIFO) Setting this bit to 1 requests sending a message. The bit will automatically clear when all the messages queued in the FIFO are successfully sent. Clearing the bit to 0 while set will request a message abort. `0` 0: (FIFO configured as a Receive FIFO) This bit has no effect.
RTREN	2	Auto RTR Enable bit `0` When a remote transmit is received, TXREQ will be unaffected `1` When a remote transmit is received, TXREQ will be set
TXPRI	1:0	Message Transmit Priority bits `0` Lowest Message Priority `1` Low Intermediate Message Priority `2` High Intermediate Message Priority `3` Highest Message Priority

C1FIFOINT14CAN FIFO Interrupt Register

Address: 0xBF8806E0
Reset: 0x00000000
Access: read/write
Size: 32-bit

14 fields

Field	Bits	What it does
TXNFULLIE	26	Transmit FIFO Not Full Interrupt Enable bit `0` Interrupt disabled for FIFO not full `1` Interrupt enabled for FIFO not full
TXHALFIE	25	Transmit FIFO Half Full Interrupt Enable bit `0` Interrupt disabled for FIFO half full `1` Interrupt enabled for FIFO half full
TXEMPTYIE	24	Transmit FIFO Empty Interrupt Enable bit `0` Interrupt disabled for FIFO empty `1` Interrupt enabled for FIFO empty
RXOVFLIE	19	Overflow Interrupt Enable bit `0` Interrupt disabled for overflow event `1` Interrupt enabled for overflow event
RXFULLIE	18	Full Interrupt Enable bit `0` Interrupt disabled for FIFO full `1` Interrupt enabled for FIFO full
RXHALFIE	17	FIFO Half Full Interrupt Enable bit `0` Interrupt disabled for FIFO half full `1` Interrupt enabled for FIFO half full
RXNEMPTYIE	16	Empty Interrupt Enable bit `0` Interrupt disabled for FIFO not empty `1` Interrupt enabled for FIFO not empty
TXNFULLIF	10	Transmit FIFO Not Full Interrupt Flag bit `0` 1: (FIFO configured as a Transmit Buffer) 1 = FIFO is not full, 0 = FIFO is full `0` 0: (FIFO configured as a Receive Buffer) Unused, reads 0
TXHALFIF	9	FIFO Transmit FIFO Half Empty Interrupt Flag bit `0` 1: (FIFO configured as a Transmit Buffer) 1 = FIFO is ? half full, 0 = FIFO is > half full `0` 0: (FIFO configured as a Receive Buffer) Unused, reads 0
TXEMPTYIF	8	Transmit FIFO Empty Interrupt Flag bit `0` 1: (FIFO configured as a Transmit Buffer) 1 = FIFO is empty, 0 = FIFO is not empty, at least 1 message queued to be transmitted `0` 0: (FIFO configured as a Receive Buffer) Unused, reads 0
RXOVFLIF	3	Receive FIFO Overflow Interrupt Flag bit `0` 1: (FIFO configured as a Transmit Buffer) Unused, reads 0 `0` 0: (FIFO configured as a Receive Buffer) 1 = Overflow event has occurred, 0 = No overflow event occurred
RXFULLIF	2	Receive FIFO Full Interrupt Flag bit `0` 1: (FIFO configured as a Transmit Buffer) Unused, reads 0 `0` 0: (FIFO configured as a Receive Buffer) 1 = FIFO is full, 0 = FIFO is not full
RXHALFIF	1	Receive FIFO Half Full Interrupt Flag bit `0` 1: (FIFO configured as a Transmit Buffer) Unused, reads 0 `0` 0: (FIFO configured as a Receive Buffer) 1 = FIFO is ? half full, 0 = FIFO is < half full
RXNEMPTYIF	0	Receive Buffer Not Empty Interrupt Flag bit `0` 0: (FIFO configured as a Receive Buffer) 1 = FIFO is not empty, has at least 1 message, 0 = FIFO is empty `1` 1: (FIFO configured as a Transmit Buffer) Unused, reads 0

C1FIFOUA14CAN FIFO User Address Register

Address: 0xBF8806F0
Reset: 0x00000000
Access: read only
Size: 32-bit

C1FIFOCI14CAN Module Message Index Register

Address: 0xBF880700
Reset: 0x00000000
Access: read only
Size: 32-bit

1 field

Field	Bits	What it does
CFIFOCI	4:0

C1FIFOCON15CAN FIFO Control Register

Address: 0xBF880710
Reset: 0x00000000
Access: read/write
Size: 32-bit

11 fields

Field	Bits	What it does
FSIZE	20:16	FIFO Size bits `0` FIFO is 1 message deep `1` FIFO is 2 messages deep `2` FIFO is 3 messages deep `31` FIFO is 32 messages deep
FRESET	14	FIFO Reset bits `0` No effect `1` FIFO will be reset when bit is set, cleared by hardware when FIFO is reset. After setting, the user application should poll whether this bit is clear before taking any action
UINC	13	Increment Head/Tail bit `0` 1: (FIFO configured as a Transmit FIFO) When this bit is set, the FIFO head will increment by a single message `0` 0: (FIFO configured as a Receive FIFO) When this bit is set, the FIFO tail will increment by a single message
DONLY	12	Store Message Data Only bit `0` 1: (FIFO configured as a Transmit FIFO) This bit is not used and has no effect. `0` 0: (FIFO configured as a Receive FIFO) 1 = Only data bytes will be stored in the FIFO, 0 = Full message is stored, including identifier
TXEN	7	TX/RX Buffer Selection bit `0` FIFO is a Receive FIFO `1` FIFO is a Transmit FIFO
TXABAT	6	Message Aborted bit `0` Message completed successfully `1` Message was aborted
TXLARB	5	Message Lost Arbitration bit `0` Message did not lose arbitration while being sent `1` Message lost arbitration while being sent
TXERR	4	Error Detected During Transmission bit `0` A bus error did not occur while the message was being sent `1` A bus error occurred while the message was being sent
TXREQ	3	Message Send Request `0` 1: (FIFO configured as a Transmit FIFO) Setting this bit to 1 requests sending a message. The bit will automatically clear when all the messages queued in the FIFO are successfully sent. Clearing the bit to 0 while set will request a message abort. `0` 0: (FIFO configured as a Receive FIFO) This bit has no effect.
RTREN	2	Auto RTR Enable bit `0` When a remote transmit is received, TXREQ will be unaffected `1` When a remote transmit is received, TXREQ will be set
TXPRI	1:0	Message Transmit Priority bits `0` Lowest Message Priority `1` Low Intermediate Message Priority `2` High Intermediate Message Priority `3` Highest Message Priority

C1FIFOINT15CAN FIFO Interrupt Register

Address: 0xBF880720
Reset: 0x00000000
Access: read/write
Size: 32-bit

14 fields

Field	Bits	What it does
TXNFULLIE	26	Transmit FIFO Not Full Interrupt Enable bit `0` Interrupt disabled for FIFO not full `1` Interrupt enabled for FIFO not full
TXHALFIE	25	Transmit FIFO Half Full Interrupt Enable bit `0` Interrupt disabled for FIFO half full `1` Interrupt enabled for FIFO half full
TXEMPTYIE	24	Transmit FIFO Empty Interrupt Enable bit `0` Interrupt disabled for FIFO empty `1` Interrupt enabled for FIFO empty
RXOVFLIE	19	Overflow Interrupt Enable bit `0` Interrupt disabled for overflow event `1` Interrupt enabled for overflow event
RXFULLIE	18	Full Interrupt Enable bit `0` Interrupt disabled for FIFO full `1` Interrupt enabled for FIFO full
RXHALFIE	17	FIFO Half Full Interrupt Enable bit `0` Interrupt disabled for FIFO half full `1` Interrupt enabled for FIFO half full
RXNEMPTYIE	16	Empty Interrupt Enable bit `0` Interrupt disabled for FIFO not empty `1` Interrupt enabled for FIFO not empty
TXNFULLIF	10	Transmit FIFO Not Full Interrupt Flag bit `0` 1: (FIFO configured as a Transmit Buffer) 1 = FIFO is not full, 0 = FIFO is full `0` 0: (FIFO configured as a Receive Buffer) Unused, reads 0
TXHALFIF	9	FIFO Transmit FIFO Half Empty Interrupt Flag bit `0` 1: (FIFO configured as a Transmit Buffer) 1 = FIFO is ? half full, 0 = FIFO is > half full `0` 0: (FIFO configured as a Receive Buffer) Unused, reads 0
TXEMPTYIF	8	Transmit FIFO Empty Interrupt Flag bit `0` 1: (FIFO configured as a Transmit Buffer) 1 = FIFO is empty, 0 = FIFO is not empty, at least 1 message queued to be transmitted `0` 0: (FIFO configured as a Receive Buffer) Unused, reads 0
RXOVFLIF	3	Receive FIFO Overflow Interrupt Flag bit `0` 1: (FIFO configured as a Transmit Buffer) Unused, reads 0 `0` 0: (FIFO configured as a Receive Buffer) 1 = Overflow event has occurred, 0 = No overflow event occurred
RXFULLIF	2	Receive FIFO Full Interrupt Flag bit `0` 1: (FIFO configured as a Transmit Buffer) Unused, reads 0 `0` 0: (FIFO configured as a Receive Buffer) 1 = FIFO is full, 0 = FIFO is not full
RXHALFIF	1	Receive FIFO Half Full Interrupt Flag bit `0` 1: (FIFO configured as a Transmit Buffer) Unused, reads 0 `0` 0: (FIFO configured as a Receive Buffer) 1 = FIFO is ? half full, 0 = FIFO is < half full
RXNEMPTYIF	0	Receive Buffer Not Empty Interrupt Flag bit `0` 0: (FIFO configured as a Receive Buffer) 1 = FIFO is not empty, has at least 1 message, 0 = FIFO is empty `1` 1: (FIFO configured as a Transmit Buffer) Unused, reads 0

C1FIFOUA15CAN FIFO User Address Register

Address: 0xBF880730
Reset: 0x00000000
Access: read only
Size: 32-bit

C1FIFOCI15CAN Module Message Index Register

Address: 0xBF880740
Reset: 0x00000000
Access: read only
Size: 32-bit

1 field

Field	Bits	What it does
CFIFOCI	4:0