BETASelected packageTO-220ABTIP31CG
NPN power transistor
TIP31C Reference Tables
Search the TIP31C pin reference and manufacturer-referenced specification tables.
Package view
Physical connections3 pinsPackage-specific numbering
Reference collection7 tables35 parameters & pin functions
Pin reference
Signal names, electrical functions and connection guidance
Physical pin numbers3 pins
Scroll within the table to see all columns and rows.
| Pin | Signal | Type | Function & connection |
|---|---|---|---|
| B | Base | Current-driven control junction.Connection guidanceUse the example’s 330 Ω base resistor and 10 kΩ base-emitter return. The buffered 5 V driver must source approximately 12.7 mA; do not assume every GPIO can do so. | |
| C | Collector | Load terminal, also connected to the metal tab.Connection guidanceConnect the 100 Ω resistor load to this terminal. The exposed tab is electrically live; insulate it when required. | |
| E | Emitter | Current return and base-drive reference.Connection guidanceConnect emitter to common driver and load ground. Front view: B1, C2, E3; tab is collector. |
No pins match these filters. Try another signal name or reset the filters.
Device and package scope
Two separately documented selections
Manufacturer-referenced values5 parameters
Scroll within the table to see all columns and rows.
| Parameter | Value | Conditions / notes |
|---|---|---|
| Through-hole | TIP31CG · TO-220 | TIP31A/D Rev. 17, June 2024 |
| Surface-mount | MJD31CT4G · DPAK | MJD31/D Rev. 21, May 2026 |
| Polarity | NPN | Manufacturer tables use magnitudes; reverse voltage/current signs for PNP |
| Terminals | B1 · C2 · E3 | Tab/contact 4 is electrically collector |
| SMD relationship | Electrically similar manufacturer counterpart | Different power and leakage limits; check the selected package |
No specifications match. Try a parameter name or a unit.
Pin function is preserved when the package changes.
Absolute voltage and current limits
Magnitudes; individual stress limits
Manufacturer-referenced values5 parameters
Scroll within the table to see all columns and rows.
| Parameter | Value | Conditions / notes |
|---|---|---|
| Collector-emitter / collector-base | 100 / 100 V | Selected C-voltage grades only |
| Emitter-base reverse voltage | 5 V | Do not apply a reverse drive without limiting it |
| DC / peak collector current | 3 / 5 A | Thermal and pulse restrictions also apply |
| Base current | 1 A | Absolute maximum |
| Junction and storage | −65 to +150°C | Both selected references |
No specifications match. Try a parameter name or a unit.
These are not simultaneous operating targets.
Gain and on-state characteristics
TC 25°C; pulse ≤300 µs, duty ≤2%
Manufacturer-referenced values6 parameters
Scroll within the table to see all columns and rows.
| Parameter | Value | Conditions / notes |
|---|---|---|
| hFE at IC 1 A | 25 minimum | VCE 4 V |
| hFE at IC 3 A | 10–50 | VCE 4 V |
| Collector-emitter saturation | 1.2 V maximum | IC 3 A; IB 375 mA |
| Base-emitter on voltage | 1.8 V maximum | IC 3 A; VCE 4 V |
| Current gain-bandwidth | 3 MHz minimum | IC 500 mA; VCE 10 V; test 1 MHz |
| Small-signal gain | 20 minimum | IC 500 mA; VCE 10 V; 1 kHz |
No specifications match. Try a parameter name or a unit.
Active-region gain does not replace a saturation base-current budget.
Off-state characteristics
Maximum magnitudes at TC 25°C
Manufacturer-referenced values5 parameters
Scroll within the table to see all columns and rows.
| Parameter | Value | Conditions / notes |
|---|---|---|
| TO-220 ICEO | 0.3 mA | VCE 60 V; base open |
| DPAK ICEO | 50 µA | VCE 60 V; base open |
| TO-220 ICES | 200 µA | VCE 100 V; VEB 0 |
| DPAK ICES | 20 µA | VCE 100 V; VEB 0 |
| Emitter leakage | 1 mA | VBE reverse 5 V; collector open |
No specifications match. Try a parameter name or a unit.
Leakage can matter even when the load is meant to be off.
Package-specific thermal limits
The boundary condition changes the rating
Manufacturer-referenced values7 parameters
Scroll within the table to see all columns and rows.
| Parameter | Value | Conditions / notes |
|---|---|---|
| TO-220 power / derating | 40 W / 0.32 W per °C | Case 25°C / above 25°C |
| TO-220 ambient power | 2 W | Ambient 25°C; derate 0.016 W/°C |
| TO-220 RθJC / RθJA | 3.125 / 62.5°C/W | Maximum reference values |
| DPAK power / derating | 15 W / 0.12 W per °C | Case 25°C / above 25°C |
| DPAK ambient power | 1.56 W | FR-4, 165 mm², 1 oz copper; derate 0.012 W/°C |
| DPAK RθJC / RθJA | 8.3 / 80°C/W | Specified mounting and minimum-pad conditions |
| Safe operating area | Check manufacturer curves | Voltage, current, duration and starting temperature together |
No specifications match. Try a parameter name or a unit.
The package image is not a heatsink rating.
12 V resistor-load switch
Explicit illustrative assumptions
Manufacturer-referenced values7 parameters
Scroll within the table to see all columns and rows.
| Parameter | Value | Conditions / notes |
|---|---|---|
| Load | 100 Ω, at least 3 W | Supply to collector |
| Base resistor / return | 330 Ω / 10 kΩ | Return resistor goes from base to emitter |
| Buffered driver | 0 V off / 5 V on | Must source about 12.7 mA |
| Assumed junctions | |VBE| 0.8 V; |VCE| 0.2 V | Teaching assumptions, not guaranteed test points |
| Base current | 12.65 mA | (5−0.8)/330−0.8/10000 |
| Collector current / forced ratio | 118 mA / 9.33 | (12−0.2)/100; IC/IB |
| Transistor / load loss | 33.7 mW / 1.392 W | Include base contribution; allow resistor thermal margin |
No specifications match. Try a parameter name or a unit.
Inductive loads require a suitable clamp and a separate transient check.
No matching rowsTry a pin name, parameter, unit or test condition, or reset the filters.