TXS0108E Specifications
Review TXS0108E electrical specifications, operating conditions and package details.
Key specifications
TXS0108E supports open-drain and push-pull signaling, subject to loading and timing limits.
Package details
TXS0108EPWR · TSSOP-20
| Property | Details |
|---|---|
| Manufacturer | Texas Instruments |
| Part number | TXS0108EPWR |
| Package | TSSOP-20 |
| Connections | 20 pins |
| Mounting | SMD |
| Lead pitch | 0.65 mm |
| Package code | TSSOP-20 |
| Thermal reference | See operating and package limits |
Supplies and operating conditions
SCES642L · November 2024
Scroll sideways to see all columns.
| Parameter | Value | Conditions / notes |
|---|---|---|
| VCCA | 1.4–3.6 V | Port A voltage domain |
| VCCB | 1.65–5.5 V | Port B voltage domain |
| Supply relationship | VCCA ≤ VCCB | Required operating condition |
| OE supply reference | VCCA | Do not drive OE from a 5 V source when VCCA is 3.3 V |
| Ambient range | −40 to +85°C | Selected catalog part |
| Local bypass | 100 nF per supply | Close to pins 2 and 19; common ground pin 11 |
No specifications match. Try a parameter name or a unit.
Recommended operating values; absolute stress ratings are not design targets.
Signal type and loading
Pass-transistor architecture
Scroll sideways to see all columns.
| Parameter | Value | Conditions / notes |
|---|---|---|
| Supported interfaces | Open drain and push pull | Only one driver active per channel |
| Internal pull-ups | Present on both ports | External pull-ups change sink current and edge behavior |
| Push-pull data-rate headline | Up to 110 Mbps | Supply, direction, load and timing conditions apply |
| Open-drain data-rate headline | Up to 1.2 Mbps | Not a guarantee for arbitrary I2C wiring or bus capacitance |
| Long cables / high capacitance | Not assumed compatible | Review datasheet edge-accelerator pulse and load constraints |
No specifications match. Try a parameter name or a unit.
Do not treat this translator as a high-current buffer.
Enable and signal states
Ideal settled states
Scroll sideways to see all columns.
| Parameter | Value | Conditions / notes |
|---|---|---|
| OE LOW | A and B high impedance | External circuitry may still establish a voltage |
| OE HIGH, A1 LOW | B1 LOW | Both supplies valid; no conflicting driver |
| OE HIGH, A1 HIGH | B1 HIGH at B-domain level | Receiver loading must be suitable |
| OE HIGH, B1 driven | A1 follows at A-domain level | Reverse direction: release the A-side driver first |
| Both ends drive opposite states | Invalid usage | Bus contention; not automatic arbitration |
No specifications match. Try a parameter name or a unit.
High impedance is not a guaranteed zero-voltage state.
3.3 V to 5 V connection
TSSOP PW pin numbers
Scroll sideways to see all columns.
| Parameter | Value | Conditions / notes |
|---|---|---|
| VCCA 2 | 3.3 V | 100 nF to GND |
| VCCB 19 | 5 V | 100 nF to GND |
| GND 11 | Common return | Join both systems |
| OE 10 | A-domain enable plus 100 kΩ to ground | LOW until rails are stable |
| A1 1 | 3.3 V push-pull source | Direction shown A → B |
| B1 20 | 5 V receiver | High impedance input |
| A2–A8 / B2–B8 | Unused channels open | Do not ground both sides of a channel as a load |
No specifications match. Try a parameter name or a unit.
Illustrative wiring and ideal voltage levels, not live simulation.
Connections by function
Select a pin for its function, connection guidance and electrical notes.