LMV358M Reference Tables, Pins & Specifications

Pin reference

Signal names, electrical functions and connection guidance

SOIC-8

Physical pin numbers8 pins

Scroll within the table to see all columns and rows.

LMV358M pin functions and connections
Signal	Type	Function & connection
OUT A	Analog output	Output of amplifier A. Connection guidance Connect Rf to IN A− and measure this node. Output swing depends on load and temperature.
IN A−	Inverting input	Feedback input of amplifier A. Connection guidance Connect the Rf/Rg junction.
IN A+	Non-inverting input	Signal input of amplifier A. Connection guidance Apply VIN relative to ground. Input common-mode range is not rail-to-rail.
V−	Negative supply	Shared lower supply rail. Connection guidance Connect to ground for the shown 5 V circuit.
IN B+	Non-inverting input	Signal input of amplifier B. Connection guidance Connect to VIN in this example.
IN B−	Inverting input	Feedback input of amplifier B. Connection guidance Join OUT B for a voltage follower.
OUT B	Analog output	Independent amplifier B output. Connection guidance Join IN B− and leave otherwise unloaded.
V+	Positive supply	Shared positive rail. Connection guidance Apply 5 V and bypass to pin 4 with 100 nF. Recommended supply 2.7–5.5 V; unlike LM358, this is not a high-voltage amplifier.

LMV358-N · LMV358M/NOPB

Manufacturer-referenced values5 parameters

Scroll within the table to see all columns and rows.

Parameter	Value	Conditions / notes
Supply	2.7–5.5 V	Recommended range
Ambient temperature	−40 to +125°C	Selected industrial part
Input common-mode range at 5 V	0–4 V specified; −0.2–4.2 V typical	CMRR ≥ 50 dB
Supply current, both channels	210 µA typical; 440 µA max	5 V, 25°C; 615 µA max over temperature
Supply absolute maximum	5.5 V	Stress limit; do not exceed

Typical extensions are not guaranteed operating margins.

5 V and 25°C unless stated

Manufacturer-referenced values5 parameters

Scroll within the table to see all columns and rows.

Bias current through high source resistance adds an input error.

Conditions matter

Manufacturer-referenced values6 parameters

Scroll within the table to see all columns and rows.

Parameter	Value	Conditions / notes
Gain-bandwidth	1 MHz typical	200 pF load
Slew rate	1 V/µs typical	Manufacturer AC test
HIGH output, 2 kΩ to midpoint	V+−40 mV typical; V+−300 mV min	5 V, 25°C
LOW output, 2 kΩ to midpoint	120 mV typical; 300 mV max	5 V, 25°C
Over-temperature swing, 2 kΩ	Within 400 mV of either rail	Specified test load
Short-circuit current	40 mA typical	Not a recommended continuous load current

Rail-to-rail does not mean zero headroom at every current.

5 V supply; light load

Manufacturer-referenced values6 parameters

Scroll within the table to see all columns and rows.

Parameter	Value	Conditions / notes
Input / ideal output	0.50 V / 1.50 V	After settling, while linear
Feedback resistor Rf	20 kΩ	OUT A1 to IN A−2
Ground resistor Rg	10 kΩ	IN A−2 to GND
Signal	VIN to pins 3 and 5	Common ground
Second channel	Join pins 6 and 7	Voltage follower; output otherwise unloaded
Bypass	100 nF	Pins 8 to 4, close to the IC

Use a high-impedance meter. The explorer uses conservative fixed headroom, not a transistor-level simulation.

LMV358M/NOPB · SOIC-8

Manufacturer-referenced values5 parameters

Scroll within the table to see all columns and rows.

Parameter	Value	Conditions / notes
Physical pins	8	SOIC top view
Pitch	1.27 mm	SMD
Maximum junction	150°C	Apply thermal derating
Storage	−65 to +150°C	Unpowered
Other package	LMV358MM/NOPB uses VSSOP8	Different footprint; not interchangeable with SOIC

No through-hole part is invented for this surface-mount device.