BETANominal reference2.495 V
Adjustable shunt regulator
TL431 Specifications
Review TL431 electrical specifications, operating conditions and package details.
Package view
Key specifications
A series resistor feeds the output. The load takes its share, while the TL431 adjusts cathode current to hold the divider near its reference.
Cathode range1–100 mA · recommended
Initial tolerance±2 % · standard grade
Ambient range0–70 °C · TL431C
Package details
TL431CLP · TO-92
| Property | Details |
|---|---|
| Manufacturer | Texas Instruments |
| Part number | TL431CLP |
| Package | TO-92 |
| Connections | 3 pins |
| Mounting | Through-hole |
| Lead pitch | 1.27 mm · straight leads |
| Package code | LP |
| Thermal reference | Package, board copper and cathode dissipation determine junction temperature |
Operating envelope
TI TL431C standard-accuracy grade
Manufacturer specifications 6 parameters
Scroll sideways to see all columns.
| Parameter | Value | Conditions / notes |
|---|---|---|
| Cathode voltage | VREF to 36 V | Referenced to the anode |
| Cathode current | 1–100 mA | Recommended range; power dissipation may impose a lower maximum |
| Ambient temperature | 0–70°C | Selected commercial C grade |
| Initial accuracy | ±2% at 25°C | A: ±1%; B: ±0.5% are different grades |
| Selected through-hole part | TL431CLP | Bulk straight-lead TO-92 |
| Selected SMD part | TL431CDBZR | SOT-23-3; different physical pin map |
No specifications match. Try a parameter name or a unit.
A shunt-current rating is not a load-current rating.
Reference and regulation
Electrical-characteristic test conditions
Manufacturer specifications 6 parameters
Scroll sideways to see all columns.
| Parameter | Value | Conditions / notes |
|---|---|---|
| Reference at 25°C | 2.440 / 2.495 / 2.550 V | Minimum / typical / maximum; VKA = VREF, IKA = 10 mA |
| Reference current | 2 µA typical; 4 µA maximum | IKA = 10 mA; R1 = 10 kΩ, R2 open |
| Minimum regulation current | 0.4 mA typical; 1 mA maximum | Do not design only around the typical value |
| Dynamic impedance | 0.2 Ω typical; 0.5 Ω maximum | f ≤ 1 kHz; IKA = 1–100 mA; VKA = VREF |
| Off-state cathode current | 0.1 µA typical; 1 µA maximum | VKA = 36 V; VREF input = 0 V |
| Output setting | VOUT ≈ VREF × (1 + RUP/RLOW) + IREF × RUP | Resistor tolerance and device errors remain |
No specifications match. Try a parameter name or a unit.
Initial tolerance, drift, loading and divider errors all contribute to real output accuracy.
Temperature and grade distinctions
Do not merge limits from different packages
Manufacturer specifications 6 parameters
Scroll sideways to see all columns.
| Parameter | Value | Conditions / notes |
|---|---|---|
| C-grade ambient | 0 to +70°C | The two orderables shown here |
| I-grade ambient | −40 to +85°C | Requires an I-grade orderable |
| Q-grade ambient | −40 to +125°C | Requires a Q-grade orderable |
| C reference change: TO-92 | 4 mV typical; 25 mV maximum | VKA = VREF; IKA = 10 mA; over C ambient range |
| C reference change: SOT-23-3 | 6 mV typical; 16 mV maximum | Different package-specific limits in the same table |
| Thermal check | TJ ≈ TA + P × θJA | Use the exact package and PCB thermal conditions |
No specifications match. Try a parameter name or a unit.
Temperature drift does not replace the initial reference-voltage tolerance.
A nominal 5 V shunt supply
12 V input · SOT-23-3 physical circuit
Manufacturer specifications 6 parameters
Scroll sideways to see all columns.
| Parameter | Value | Conditions / notes |
|---|---|---|
| Feed resistor | 680 Ω, at least 0.25 W | 12 V to K1 / output node |
| Upper divider resistor | 10 kΩ | K1 to REF2 |
| Lower divider resistor | 10 kΩ | REF2 to A3 / GND |
| Example load | 1 kΩ | Output to GND; approximately 5 mA |
| Anode | Pin 3 to GND | The TO-92 equivalent is pin 2 |
| Output capacitor | None in this teaching circuit | Capacitive-load stability must be checked before adding one |
No specifications match. Try a parameter name or a unit.
The diagram is a low-voltage teaching circuit, not a mains-connected power supply.
Follow the current budget
Illustrative typical-value arithmetic
Manufacturer specifications 7 parameters
Scroll sideways to see all columns.
| Parameter | Value | Conditions / notes |
|---|---|---|
| Ideal divider output | 4.990 V | 2.495 × (1 + 10/10) |
| Reference-current correction | +0.020 V | 2 µA × 10 kΩ |
| Illustrative output | 5.010 V | Before tolerances, temperature and load errors |
| Feed current | 10.279 mA | (12 − 5.01) / 680 |
| Load / upper-divider currents | 5.010 mA / 0.2515 mA | 1 kΩ load; lower-divider current plus 2 µA |
| Remaining cathode current | Approximately 5.018 mA | Feed minus load minus upper-divider current |
| Feed resistor / TL431 power | 71.9 mW / 25.1 mW | Nominal arithmetic; include worst-case input/load margins |
No specifications match. Try a parameter name or a unit.
These are calculations, not live readings or an electrical simulation.
Physical pin correspondence
Check orientation before connecting
Manufacturer specifications 6 parameters
Scroll sideways to see all columns.
| Parameter | Value | Conditions / notes |
|---|---|---|
| Cathode K | TO-92: 1 · SOT-23: 1 | Controlled shunt/output node |
| Anode A | TO-92: 2 · SOT-23: 3 | Common return |
| Reference REF | TO-92: 3 · SOT-23: 2 | Divider sense input |
| TO-92 pinout picture | Bottom view, flat edge below | Left-to-right: 3 REF, 2 A, 1 K; top-side PCB view is mirrored |
| SOT-23 pinout picture | Top view | K1 upper left, REF2 lower left, A3 at right |
| TL432 | Same function; different small-package pinouts | Do not substitute by name alone |
No specifications match. Try a parameter name or a unit.
The straight-lead TO-92 footprint is not the wider formed-lead footprint.
Stability and absolute limits
Stress limits are not operating targets
Manufacturer specifications 6 parameters
Scroll sideways to see all columns.
| Parameter | Value | Conditions / notes |
|---|---|---|
| Cathode absolute voltage | 37 V | Recommended maximum remains 36 V |
| Cathode absolute current | −100 to +150 mA | Do not use as a normal operating range |
| Reference absolute current | −0.05 to +10 mA | Input stress limit |
| Junction / storage | 150°C / −65 to +150°C | Absolute limits |
| Capacitive load | Can destabilize the shunt loop | Check the manufacturer stability curves for voltage, current and capacitance |
| Worst-case power | VKA × IKA | Evaluate high input / light load, not only the nominal circuit |
No specifications match. Try a parameter name or a unit.
Allow electrical and thermal margin, and verify stability in the actual circuit.
Connections by function
Select a pin for its function, connection guidance and electrical notes.