Skip to datasheet
Adjustable 1 A synchronous buck converter

TPS62160 Reference Tables

Search the TPS62160 pin reference and manufacturer-referenced specification tables.

Package view
Selected packageWSON-8 + EPTPS62160DSGR
Physical connections9 pinsPackage-specific numbering
Reference collection4 tables17 parameters & pin functions

Pin reference

Signal names, electrical functions and connection guidance

WSON-8 + EP
Physical pin numbers9 pins

Scroll within the table to see all columns and rows.

TPS62160 pin functions and connections
PinSignalTypeFunction & connection
PGNDPower returnReturn for the switching stage.
Connection guidance

Connect the power ground plane and local capacitor returns.

VINSupply inputInput power and control supply.
Connection guidance

Apply 3–17 V and bypass locally with 10 µF in the example.

ENEnable inputHIGH enables conversion; LOW disables it.
Connection guidance

Tie to VIN for the illustrated always-enabled supply.

AGNDAnalog returnReference for feedback and control.
Connection guidance

Join to PGND with the recommended short ground layout.

FBFeedback inputSenses the output divider on the adjustable TPS62160.
Connection guidance

Connect 390 kΩ from output and 180 kΩ to AGND in the 2.53 V example.

Do not copy the grounded-FB connection of fixed-output TPS62161/2/3.

VOSOutput senseDirect feedback for the DCS control loop.
Connection guidance

Connect directly to VOUT at the output capacitor; not to SW.

SWSwitch nodeSwitching output to the inductor.
Connection guidance

Connect 2.2 µH from SW to VOUT; keep the loop compact.

PGOpen-drain statusSignals when the output is within its power-good window.
Connection guidance

Use a 100 kΩ pull-up to VOUT if the status is used.

High impedance when the device is disabled; it is not a push-pull output.

EP / AGNDWSON underside padPresent only on the WSON package.
Connection guidance

Solder to analog ground copper with appropriate thermal layout.

The VSSOP package has no exposed pad.

WSON-8 + EP · Top view · Select a pin number to open its interactive pinout.

Operating reference

Adjustable TPS62160; distinguish fixed-output variants.

Manufacturer-referenced values6 parameters

Scroll within the table to see all columns and rows.

ParameterValueConditions / notes
Input supply3–17 VRecommended operation
Output adjustment0.9–6 VMaintain the needed input headroom
Output currentUp to 1 AInductor, thermal and input/output conditions matter
Feedback reference0.8 V nominalVOUT = 0.8 × (1 + Rtop/Rbottom)
Switching frequency2.25 MHz typicalPower-save behavior at light load
Quiescent current17 µA typicalManufacturer conditions apply

Review electrical limits and control-mode behavior in the source PDF.

Example bill of materials

5 V to approximately 2.53 V.

Manufacturer-referenced values6 parameters

Scroll within the table to see all columns and rows.

ParameterValueConditions / notes
L12.2 µHChoose sufficient saturation-current margin
CIN10 µFLow-ESR ceramic; verify effective biased capacitance
COUT22 µFAccount for voltage and temperature derating
Rtop / Rbottom390 kΩ / 180 kΩNominal output 2.533 V
PG pull-up100 kΩ to VOUTOptional status output
EN / VOSVIN / VOUT respectivelyDo not connect VOS to the switch node

Use the recommended layout and inductor/capacitor selection guidance.

Power and feedback example

Assumed load 0.5 A and efficiency 90%.

Manufacturer-referenced values5 parameters

Scroll within the table to see all columns and rows.

ParameterValueConditions / notes
Nominal output2.533 V0.8 × (1 + 390/180)
Output power1.267 W2.533 V × 0.5 A
Average input current≈ 0.281 A1.267 W / (5 V × 0.9)
Total estimated loss≈ 0.141 W1.267 W / 0.9 − 1.267 W
Ideal PWM duty≈ 50.7%VOUT/VIN; losses alter this

The assumed efficiency is illustrative; check actual curves and hardware.

Read each value with its conditions

Typical values describe the stated test conditions. Absolute maximum ratings are stress limits, not operating targets.

Texas Instruments · SLVSAM2E · May 2017
Official PDF datasheet

Component view