Skip to datasheet
Low-noise programmable positive LDO

TPS7A4700 Specifications

Review TPS7A4700 electrical specifications, operating conditions and package details.

Key specifications

Ground-or-open programming for quiet analog rails.

Programmable output1.4–20.5 V Ground-or-open setting
Output capability1 A Thermal constraints apply
Output noise4 µVrms 10 Hz–100 kHz; specified conditions
Junction range−40–125 °C Reference operating range

Operating profile

Supply, signals and operating conditions

TPS7A4700 operating profile
ParameterValueConditions / notes
Example input7 VPositive supply
Example output5 V1.4 + 3.2 + 0.4 V
Use these values with the stated grade and test conditions.

Package details

TPS7A4700RGWR · VQFN-20

Selected package
Selected TPS7A4700 physical package
PropertyDetails
ManufacturerTexas Instruments
Part numberTPS7A4700RGWR
PackageVQFN-20
Connections21 pins
MountingSMD
Lead pitch0.65 mm
Package codeVQFN-20
Thermal referenceSolder exposed pad to its specified net; design thermal vias and paste for assembly.

Electrical reference

Use the recommended-condition table, not only headline ratings.

Scroll sideways to see all columns.

ParameterValueConditions / notes
Recommended input3–35 VSource recommended conditions
Absolute input maximum36 VStress limit; not a continuous design target
TPS7A4700 output settings1.4–20.5 VGround selected programming pins
Output currentUp to 1 AObserve thermal and dropout constraints
Typical dropout307 mV at 1 AManufacturer conditions
Typical noise4 µVrms, 10 Hz–100 kHzNoise filtering and layout affect results

TPS7A4701 also supports an external divider; that feature is not attributed to TPS7A4700.

5 V programming example

VOUT = 1.4 V + sum of grounded weights.

Scroll sideways to see all columns.

ParameterValueConditions / notes
Pin 6 · 3P2VGNDAdds 3.2 V
Pin 10 · 0P4VGNDAdds 0.4 V
Pins 4, 5, 8, 9, 11, 12OpenNo additional output contribution
Pin 3 · SENSEOUTDirect output sensing
Pin 13 · ENINAlways-enabled example
Output calculation1.4 + 3.2 + 0.4 = 5.0 VNominal setting

Programming pins must be grounded or left floating, never positively driven.

Capacitors and layout

Example values follow manufacturer recommendations.

Scroll sideways to see all columns.

ParameterValueConditions / notes
Input capacitor10 µFAt least 1 µF required; account for bias derating
Output capacitor47 µF ceramicAt least 10 µF required
Noise reduction1 µFAt least 10 nF required
Thermal padGround planeSolder and provide a suitable thermal path
Both input / output pinsJoin their respective railsKeep current paths short

Capacitance requirements refer to effective values in operation.

Illustrative thermal budget

7 V input, 5 V output, 0.25 A load.

Scroll sideways to see all columns.

ParameterValueConditions / notes
Load power1.25 W5 V × 0.25 A
Pass-stage loss≈ 0.50 W(7 − 5) V × 0.25 A
Idealized conversion ratio71.4%5 / 7; ignores quiescent power
At 1 A load≈ 2 W pass lossRequires a carefully checked thermal design

These calculations exclude quiescent current and are not a thermal simulation.

Connections by function

Select a pin for its function, connection guidance and electrical notes.

Supply4 pins

Not connected4 pins

Sense and filtering2 pins

Enable / programming9 pins

Ground2 pins

Read the conditions with every value

Typical values describe stated test conditions. Absolute maximum ratings are stress limits, not operating targets.

Official PDF datasheet

Component view