Skip to datasheet
Eight-channel push-pull level translator

TXB0108 Specifications

Review TXB0108 electrical specifications, operating conditions and package details.

Key specifications

TXB0108 requires a sufficiently strong external push-pull driver; it is unsuitable for ordinary open-drain buses.

Bidirectional channels8 Noninverting
A supply1.2–3.6 V
B supply1.65–5.5 V
Ambient−40–85 °C

Package details

TXB0108PWR · TSSOP-20

Selected package
Selected TXB0108 physical package
PropertyDetails
ManufacturerTexas Instruments
Part numberTXB0108PWR
PackageTSSOP-20
Connections20 pins
MountingSMD
Lead pitch0.65 mm
Package codeTSSOP-20
Thermal referenceSee operating and package limits

Supplies and operating conditions

SCES643L · February 2026

Scroll sideways to see all columns.

ParameterValueConditions / notes
VCCA1.2–3.6 VPort A voltage domain
VCCB1.65–5.5 VPort B voltage domain
Supply relationshipVCCA ≤ VCCBRequired operating condition
OE supply referenceVCCADo not drive OE from a 5 V source when VCCA is 3.3 V
Ambient range−40 to +85°CSelected catalog part
Local bypass100 nF per supplyClose to pins 2 and 19; common ground pin 11

Recommended operating values; absolute stress ratings are not design targets.

Signal type and loading

Auto-direction buffer architecture

Scroll sideways to see all columns.

ParameterValueConditions / notes
External driverPush-pull, able to overdrive the weak bufferDo not use ordinary open-drain I2C
External pull resistorsPrefer none; if required, greater than 50 kΩStrong pulls can prevent valid HIGH/LOW levels
Data rateSupply, direction and load dependentUse the PW package timing tables; no universal speed claim
Long cables / high capacitanceNot assumed compatibleOne-shot edge acceleration is intended for appropriate short interconnects
Output loadingLogic input, not an LED or power loadKeep static and capacitive load within source specifications

Do not treat this translator as a high-current buffer.

Enable and signal states

Ideal settled states

Scroll sideways to see all columns.

ParameterValueConditions / notes
OE LOWA and B high impedanceExternal circuitry may still establish a voltage
OE HIGH, A1 LOWB1 LOWBoth supplies valid; no conflicting driver
OE HIGH, A1 HIGHB1 HIGH at B-domain levelReceiver loading must be suitable
OE HIGH, B1 drivenA1 follows at A-domain levelReverse direction: release the A-side driver first
Both ends drive opposite statesInvalid usageBus contention; not automatic arbitration

High impedance is not a guaranteed zero-voltage state.

3.3 V to 5 V connection

TSSOP PW pin numbers

Scroll sideways to see all columns.

ParameterValueConditions / notes
VCCA 23.3 V100 nF to GND
VCCB 195 V100 nF to GND
GND 11Common returnJoin both systems
OE 10A-domain enable plus 100 kΩ to groundLOW until rails are stable
A1 13.3 V push-pull sourceDirection shown A → B
B1 205 V receiverHigh impedance input
A2–A8 / B2–B8Unused A grounded, matching B openDo not ground both sides of a channel as a load

Illustrative wiring and ideal voltage levels, not live simulation.

Connections by function

Select a pin for its function, connection guidance and electrical notes.

Bidirectional signals16 pins

Supply2 pins

Output enable1 pin

Ground1 pin

Read the conditions with every value

Typical values describe stated test conditions. Absolute maximum ratings are stress limits, not operating targets.

Official PDF datasheet

Component view