Skip to datasheet
Split-output low-side gate driver

UCC27511 Reference Tables

Search the UCC27511 pin reference and manufacturer-referenced specification tables.

Selected packageSOT-23-6UCC27511DBVR
Physical connections6 pinsPackage-specific numbering
Reference collection4 tables20 parameters & pin functions

Pin reference

Signal names, electrical functions and connection guidance

SOT-23-6
Physical pin numbers6 pins

Scroll within the table to see all columns and rows.

UCC27511 pin functions and connections
PinSignalTypeFunction & connection
VDDSupplyBias supply for the output stage.
Connection guidance

12 V; 100 nF and 1 µF local bypass.

OUTHSource outputCharges the external transistor gate.
Connection guidance

10 Ω turn-on resistor to the gate.

OUTLSink outputDischarges the external transistor gate.
Connection guidance

4.7 Ω turn-off resistor to the same gate.

GNDGroundReference for input and output voltages.
Connection guidance

Short return to MOSFET source and supply ground.

IN−Inverting inputHIGH inhibits the output; floating is not an enabled state.
Connection guidance

Ground for noninverting operation.

IN+Noninverting inputHIGH requests a driven gate when IN− is LOW.
Connection guidance

3.3 V PWM input; 100 kΩ pulldown.

SOT-23-6 · Top view · Select a pin number to open its interactive pinout.

Electrical operating limits

Use the selected device and grade

Manufacturer-referenced values7 parameters

Scroll within the table to see all columns and rows.

ParameterValueConditions / notes
Driver supply4.5–18 VRecommended operating range
Input HIGH2.4 V maximum high threshold3.3 V logic example
Input LOW1.0 V minimum low thresholdUse a defined LOW level
Peak output4 A source / 8 A sinkPulsed gate charging at source conditions
Typical propagation delay13 nsSpecified supply, load and temperature
Typical rise / fall9 / 7 nsSource test circuit; not guaranteed for every MOSFET
Junction temperature−40 to +140°CThermal design still required

Do not treat peak current or absolute maxima as continuous operating ratings.

Input and output logic

Gate is driven HIGH only for IN+=1 and IN−=0

Manufacturer-referenced values6 parameters

Scroll within the table to see all columns and rows.

ParameterValueConditions / notes
IN+ / IN− = 0 / 0Gate LOWOUTL discharges
1 / 0Gate HIGHOUTH charges
0 / 1Gate LOWInhibited
1 / 1Gate LOWInhibited
Floating inputOutput held LOWBias both inputs deliberately
VDD undervoltageOutputs held LOWFollow UVLO thresholds and supply sequencing

Gate voltage is measured relative to the MOSFET source.

Gate-charge example

Illustrative MOSFET Qg=20 nC at the selected drive voltage

Manufacturer-referenced values7 parameters

Scroll within the table to see all columns and rows.

ParameterValueConditions / notes
VDD / frequency12 V / 20 kHzExample only
Qg20 nCUse the actual MOSFET gate-charge curve
Average gate-charge currentQg × f = 0.4 mAPer active channel
Gate-drive energy per secondQg × VDD × f = 4.8 mWNot total driver or MOSFET loss
Series gate resistance10 Ω on / 4.7 Ω offTune against ringing, EMI and switching loss
Gate pulldown100 kΩGate to source
Local bypass100 nF + 1 µFVery short VDD/GND loop

Peak switching current, average gate charge and load current are distinct.

Read each value with its conditions

Typical values describe the stated test conditions. Absolute maximum ratings are stress limits, not operating targets.

Texas Instruments · SLUSAW9F · November 2014
Official PDF datasheet

Component view