TMP36 Reference Tables
Search the TMP36 pin reference and manufacturer-referenced specification tables.
Pin reference
Signal names, electrical functions and connection guidance
Scroll within the table to see all columns and rows.
| Pin | Signal | Type | Function & connection |
|---|---|---|---|
| +VS | Supply | Positive supply input.Connection guidanceConnect a regulated 2.7–5.5 V rail and a local 100 nF bypass capacitor. The basic circuit uses 3.3 V. Keep the supply within the operating range. | |
| VOUT | Analog output | Temperature output with a 500 mV offset and a 10 mV/°C slope.Connection guidanceConnect to a high-impedance ADC input; measure against the same ground. T°C = (VOUT − 0.500 V) / 0.010 V. This is not the zero-offset LM35 equation. | |
| GND | Ground | Return for the supply and analog measurement.Connection guidanceConnect to the ADC ground with a short, quiet return. | |
| SHUTDOWN | Active-LOW shutdown | LOW disables the output stage and leaves VOUT high impedance.Connection guidanceTie to +VS when unused. Otherwise use a compatible control level. Only the SOIC and SOT-23 packages expose this function. | |
| NC | No connection | Unused physical contact in this package.Connection guidanceLeave unconnected. Do not use an NC contact as a signal or supply junction. | |
| NC | No connection | Unused physical contact in this package.Connection guidanceLeave unconnected. Do not use an NC contact as a signal or supply junction. | |
| NC | No connection | Unused physical contact in this package.Connection guidanceLeave unconnected. Do not use an NC contact as a signal or supply junction. | |
| NC | No connection | Unused physical contact in this package.Connection guidanceLeave unconnected. Do not use an NC contact as a signal or supply junction. |
No pins match these filters. Try another signal name or reset the filters.
Operating conditions
Selected TMP36 G-grade parts
Scroll within the table to see all columns and rows.
| Parameter | Value | Conditions / notes |
|---|---|---|
| Supply | 2.7–5.5 V | +VS relative to GND |
| Specified temperature | −40°C to +125°C | All three selected package variants |
| Unloaded supply current | 50 µA maximum | Normal operation |
| Shutdown current | 0.01 µA typical; 0.5 µA maximum | SOT-23 / SOIC only; unloaded |
| Self-heating | Less than 0.1°C | Typical still-air behavior stated by the manufacturer |
| Bypass | 100 nF | Place close to +VS and GND |
No specifications match. Try a parameter name or a unit.
Thermal coupling to the PCB or nearby power parts can outweigh the sensor’s intrinsic error.
Voltage-to-temperature relationship
Nominal transfer function
Scroll within the table to see all columns and rows.
| Parameter | Value | Conditions / notes |
|---|---|---|
| Transfer equation | VOUT = 0.500 + 0.010 × T | Volts and degrees Celsius |
| Inverse equation | T = (VOUT − 0.500) × 100 | Temperature in °C |
| −40°C | 100 mV | Nominal output |
| 0°C | 500 mV | Offset, not zero volts |
| 25°C | 750 mV | Room-temperature nominal output |
| 100°C | 1.500 V | Nominal output |
| 125°C | 1.750 V | Upper specified-temperature output |
No specifications match. Try a parameter name or a unit.
These ideal voltages illustrate the transfer function; sensor error is not included.
Accuracy and loading
Do not substitute the F-grade limits
Scroll within the table to see all columns and rows.
| Parameter | Value | Conditions / notes |
|---|---|---|
| G-grade error at 25°C | ±1°C typical; ±3°C maximum | TMP36GT9Z, TMP36GRTZ and TMP36GSZ |
| G-grade over rated range | ±2°C typical; ±4°C maximum | −40 to +125°C |
| F-grade alternative | ±2°C at 25°C; ±3°C over range | Maximum limits for different order codes |
| Linearity | ±0.5°C typical | Not the complete accuracy limit |
| Output load range | 0–50 µA | Use a high-impedance measurement input |
| Load regulation at 25°C | 6 m°C/µA typical; 20 m°C/µA maximum | 0–50 µA load |
| Supply rejection at 25°C | 30 m°C/V typical; 100 m°C/V maximum | Specified supply variation |
No specifications match. Try a parameter name or a unit.
ADC quantization, voltage-reference error and sensor error are separate contributions.
3.3 V ADC example
Ideal 12-bit straight-binary conversion
Scroll within the table to see all columns and rows.
| Parameter | Value | Conditions / notes |
|---|---|---|
| Reference / resolution | 3.3 V / 4096 levels | 12-bit example; use your actual ADC transfer convention |
| One code width | 0.8057 mV | 3.3 V ÷ 4096 |
| Temperature code width | 0.08057°C | ADC voltage step ÷ 10 mV/°C |
| 25°C ideal voltage | 0.750 V | Before conversion errors |
| Nominal ADC code | 930 | floor(0.750 × 4096 ÷ 3.3) |
| Lower-edge reconstruction | 0.74927 V → 24.93°C | code × 3.3 ÷ 4096; a bin-center estimate differs by half a code |
| Reference calibration | Measure or calibrate VREF | A nominal supply is not an exact reference |
No specifications match. Try a parameter name or a unit.
The displayed calculation is educational; it is not a claim of ±0.08°C sensor accuracy.
Package correspondence
Function identities stay constant; lead numbers change
Scroll within the table to see all columns and rows.
| Parameter | Value | Conditions / notes |
|---|---|---|
| +VS | TO-92 1 · SOT-23 2 · SOIC 8 | Positive supply |
| VOUT | TO-92 2 · SOT-23 1 · SOIC 1 | Analog temperature voltage |
| GND | TO-92 3 · SOT-23 5 · SOIC 4 | Common return |
| SHUTDOWN | Absent · SOT-23 4 · SOIC 5 | LOW disables the output; tie to +VS when unused |
| No connection | SOT-23 3 · SOIC 2,3,6,7 | Leave unconnected |
| Through-hole order | TMP36GT9Z | T-3, three straight leads |
| Surface-mount orders | TMP36GRTZ / TMP36GSZ | RJ-5 / R-8; G-grade limits |
No specifications match. Try a parameter name or a unit.
The TO-92 graphic is a front view with the flat face toward you. SMD pinouts are top views.
Wiring, layout and limits
Keep the analog reading quiet
Scroll within the table to see all columns and rows.
| Parameter | Value | Conditions / notes |
|---|---|---|
| Sensor output | High-impedance ADC input | Account for sample-and-hold settling and input loading |
| Ground | Shared sensor/ADC return | Avoid a motor or high-current return path |
| Shutdown output state | High impedance | An external ADC reading is not valid while shut down |
| Unused shutdown | Tie to +VS | SMD packages only |
| Supply absolute limit | 7 V | Stress boundary, not an operating setpoint |
| Maximum junction temperature | 175°C | Absolute rating; specified measurement range ends at 125°C |
| Storage | −65°C to +160°C | Unpowered storage range |
| Package geometry | TO-92 / SOT-23-5 / SOIC-8 | Original package-specific KiCad exports |
No specifications match. Try a parameter name or a unit.
Keep traces short, add the local bypass and consider heat conducted through the leads.
No matching rowsTry a pin name, parameter, unit or test condition, or reset the filters.