TPS61200 Reference Tables
Search the TPS61200 pin reference and manufacturer-referenced specification tables.
Pin reference
Signal names, electrical functions and connection guidance
Scroll within the table to see all columns and rows.
| Pin | Signal | Type | Function & connection |
|---|---|---|---|
| VAUX | Auxiliary control supply | Auxiliary control supply.Connection guidanceFit 0.1 µF to GND for this 3.3 V example. Not a general-purpose power output. | |
| VOUT | Regulated output | Regulated output.Connection guidanceConnect local output capacitance and the feedback divider. | |
| L | Inductor switching node | Inductor switching node.Connection guidanceConnect a 2.2 µH inductor from the input source to this pin. | |
| PGND | Power ground | Power ground.Connection guidanceReturn the high-current capacitor loops here. | |
| VIN | Input voltage | Input voltage.Connection guidanceConnect the input source and local input bypass. | |
| EN | Enable input | Enable input.Connection guidanceTie to VIN to enable, or drive within specified thresholds. Never leave floating. | |
| UVLO | Undervoltage monitor input | Undervoltage monitor input.Connection guidanceTie to VAUX when the external undervoltage function is unused, as in this example. | |
| PS | Power-save control | Power-save control.Connection guidanceLow enables power save; high disables it. Do not leave floating. | |
| GND | Control ground | Control ground.Connection guidanceJoin the quiet control returns and power ground locally. | |
| FB | Output feedback | Output feedback.Connection guidanceConnect the output resistor-divider junction. | |
| PGND / EP | Exposed thermal pad | Exposed thermal pad.Connection guidanceSolder to PGND copper. Footprint number 11 denotes the underside pad. |
No pins match these filters. Try another signal name or reset the filters.
Package connections
Numbered physical contacts and underside pad
Scroll within the table to see all columns and rows.
| Parameter | Value | Conditions / notes |
|---|---|---|
| 1 · VAUX | Auxiliary control supply | Fit 0.1 µF to GND for this 3.3 V example. Not a general-purpose power output. |
| 2 · VOUT | Regulated output | Connect local output capacitance and the feedback divider. |
| 3 · L | Inductor switching node | Connect a 2.2 µH inductor from the input source to this pin. |
| 4 · PGND | Power ground | Return the high-current capacitor loops here. |
| 5 · VIN | Input voltage | Connect the input source and local input bypass. |
| 6 · EN | Enable input | Tie to VIN to enable, or drive within specified thresholds. Never leave floating. |
| 7 · UVLO | Undervoltage monitor input | Tie to VAUX when the external undervoltage function is unused, as in this example. |
| 8 · PS | Power-save control | Low enables power save; high disables it. Do not leave floating. |
| 9 · GND | Control ground | Join the quiet control returns and power ground locally. |
| 10 · FB | Output feedback | Connect the output resistor-divider junction. |
| 11 · PGND / EP | Exposed thermal pad | Solder to PGND copper. Footprint number 11 denotes the underside pad. |
No specifications match. Try a parameter name or a unit.
Leadless contacts are plated lands, not long protruding legs. Pad 11 represents the soldered underside ground pad.
Supply and electrical characteristics
Read conditions alongside every rating
Scroll within the table to see all columns and rows.
| Parameter | Value | Conditions / notes |
|---|---|---|
| Input operating range | 0.3–5.5 V | Available output current depends strongly on input voltage |
| Minimum startup input | 0.5 V | Do not confuse with the 0.3 V operating minimum |
| Adjustable output | 1.8–5.5 V | Use the FB divider |
| Feedback voltage | 495 / 500 / 505 mV | Min / typ / max |
| Oscillator | 1.25 MHz minimum; 1.65 MHz typical | Electrical characteristics table |
| Average inductor-current limit | 1.2 / 1.35 / 1.5 A | Min / typ / max at VOUT=3.3 V |
| Efficiency headline | Above 90% under stated conditions | 300 mA at 3.3 V with VIN ≥2.4 V, or 600 mA at 5 V with VIN ≥3 V |
| VAUX range | 2.4–5.5 V | Control-supply node; see startup behavior |
No specifications match. Try a parameter name or a unit.
A current limit is not a guarantee of output current at every input voltage.
Control modes and startup
Define every logic input
Scroll within the table to see all columns and rows.
| Parameter | Value | Conditions / notes |
|---|---|---|
| EN | High enables; low disables | Thresholds depend on input voltage below 1.5 V |
| EN thresholds above 1.5 V VIN | Low ≤0.4 V; high ≥1.2 V | Do not leave the input floating |
| PS low / high | Power save enabled / disabled | Low ≤0.4 V; high ≥1.2 V |
| UVLO falling threshold | 235 / 250 / 265 mV | Min / typ / max |
| UVLO rising threshold | 330 / 350 / 370 mV | Min / typ / max; substantial hysteresis |
| Unused UVLO | Tie to VAUX | Do not ground it in the always-enabled example |
| Down-conversion mode | Automatic when required | See efficiency and regulation conditions when input exceeds output |
| Shutdown | Load disconnect | Output capacitor can retain charge |
No specifications match. Try a parameter name or a unit.
Power-save bursts are expected at light load and must not be mistaken for a defective oscillator.
Layout and passive components
A switching converter needs a compact PCB
Scroll within the table to see all columns and rows.
| Parameter | Value | Conditions / notes |
|---|---|---|
| Switching loop | Keep inductor and power capacitors close | Avoid long breadboard-style loops in real hardware |
| Feedback | Route away from switching nodes | Sense at the output capacitor; use a quiet ground return |
| Inductor | 2.2 µH in the worked circuit | Check peak/saturation current, DCR and core losses |
| Capacitors | Ceramic with adequate effective capacitance | DC bias can reduce nominal capacitance considerably |
| Exposed pad | Solder to PGND copper | Add thermal vias and paste windows appropriate to the assembly |
| Footprint scope | Core land geometry provided | PCB thermal extensions, solder mask and paste design remain assembly-specific |
No specifications match. Try a parameter name or a unit.
The illustrations explain connections, not a finished switching-power PCB layout.
Temperature and stress limits
Recommended operation and stress ratings are different
Scroll within the table to see all columns and rows.
| Parameter | Value | Conditions / notes |
|---|---|---|
| Ambient operating range | −40 to +85°C | Recommended free-air range |
| Junction operating range | −40 to +125°C | Recommended range |
| Storage | −65 to +150°C | Unpowered |
| Voltage stress | −0.3 to +7 V on specified electrical nodes | Absolute maximum; not an operating target |
| DRC junction-to-ambient | 41.2°C/W | Manufacturer reference board; actual layout changes temperature |
| Representative control current | 50 µA typical / 70 µA max at VOUT | See source test conditions; this is not the total loaded input current |
| Thermal shutdown | 140°C typical; 20°C typical hysteresis | Protection threshold, not a normal operating temperature |
No specifications match. Try a parameter name or a unit.
Use real loss and thermal measurements for the intended load and input range.
Nominal 3.3 V circuit
Component choices and calculated load
Scroll within the table to see all columns and rows.
| Parameter | Value | Conditions / notes |
|---|---|---|
| Input source | 3 V nominal | Demonstration input, not the lowest operating corner |
| Inductor | 2.2 µH from input rail to L3 | Choose adequate saturation current and low DCR |
| Input capacitor | 10 µF | Close to input / PGND |
| Output capacitor | 22 µF | Effective value and loop stability must be checked |
| VAUX capacitor | 0.1 µF to GND | Use about 1 µF when output is below 2.5 V |
| Feedback divider | 1.12 MΩ top / 200 kΩ bottom | Nominal 3.3 V from the 0.5 V reference |
| Enable and mode | EN6 to VIN; PS8 to GND | Power-save mode permitted |
| Unused undervoltage monitor | UVLO7 to VAUX1 | Retains required control behavior |
| Test load | 33 Ω | 100 mA nominal; 0.33 W, use a suitable power rating |
No specifications match. Try a parameter name or a unit.
Example values require validation in the actual PCB, including startup, transient behavior and effective capacitance.
No matching rowsTry a pin name, parameter, unit or test condition, or reset the filters.