Skip to datasheet
Low-input-voltage synchronous boost converter

TPS61200 Specifications

Review TPS61200 electrical specifications, operating conditions and package details.

Key specifications

Build a higher rail from a low-voltage source with controlled startup and load disconnect. The inductor carries switching current; the feedback network senses the output and the controller adjusts energy transfer.

Operating input0.3–5.5 V 0.5 V minimum startup input
Adjustable output1.8–5.5 V Headroom, power and loop constraints apply
Current-limit figure1.35 A Typical average inductor limit; not output current
Recommended ambient−40–85 °C · junction range is separate

Operating profile

Supply, signals and operating conditions

TPS61200 operating profile
ParameterValueConditions / notes
Selected packageVSON-10 + EPTPS61200DRCR
Exposed pad 11PGNDSolder to power-ground copper
Example output3.3 V1.12 MΩ / 200 kΩ divider
Use these values with the stated grade and test conditions.

Package details

TPS61200DRCR · VSON-10 + EP

Selected package
Selected TPS61200 physical package
PropertyDetails
ManufacturerTexas Instruments
Part numberTPS61200DRCR
PackageVSON-10 + EP
Connections11 pins
MountingSMD
Lead pitch0.50 mm
Package codeDRC
Thermal referenceExposed pad 11 to PGND; solder to ground copper

Package connections

Numbered physical contacts and underside pad

Scroll sideways to see all columns.

ParameterValueConditions / notes
1 · VAUXAuxiliary control supplyFit 0.1 µF to GND for this 3.3 V example. Not a general-purpose power output.
2 · VOUTRegulated outputConnect local output capacitance and the feedback divider.
3 · LInductor switching nodeConnect a 2.2 µH inductor from the input source to this pin.
4 · PGNDPower groundReturn the high-current capacitor loops here.
5 · VINInput voltageConnect the input source and local input bypass.
6 · ENEnable inputTie to VIN to enable, or drive within specified thresholds. Never leave floating.
7 · UVLOUndervoltage monitor inputTie to VAUX when the external undervoltage function is unused, as in this example.
8 · PSPower-save controlLow enables power save; high disables it. Do not leave floating.
9 · GNDControl groundJoin the quiet control returns and power ground locally.
10 · FBOutput feedbackConnect the output resistor-divider junction.
11 · PGND / EPExposed thermal padSolder to PGND copper. Footprint number 11 denotes the underside pad.

Leadless contacts are plated lands, not long protruding legs. Pad 11 represents the soldered underside ground pad.

Supply and electrical characteristics

Read conditions alongside every rating

Scroll sideways to see all columns.

ParameterValueConditions / notes
Input operating range0.3–5.5 VAvailable output current depends strongly on input voltage
Minimum startup input0.5 VDo not confuse with the 0.3 V operating minimum
Adjustable output1.8–5.5 VUse the FB divider
Feedback voltage495 / 500 / 505 mVMin / typ / max
Oscillator1.25 MHz minimum; 1.65 MHz typicalElectrical characteristics table
Average inductor-current limit1.2 / 1.35 / 1.5 AMin / typ / max at VOUT=3.3 V
Efficiency headlineAbove 90% under stated conditions300 mA at 3.3 V with VIN ≥2.4 V, or 600 mA at 5 V with VIN ≥3 V
VAUX range2.4–5.5 VControl-supply node; see startup behavior

A current limit is not a guarantee of output current at every input voltage.

Control modes and startup

Define every logic input

Scroll sideways to see all columns.

ParameterValueConditions / notes
ENHigh enables; low disablesThresholds depend on input voltage below 1.5 V
EN thresholds above 1.5 V VINLow ≤0.4 V; high ≥1.2 VDo not leave the input floating
PS low / highPower save enabled / disabledLow ≤0.4 V; high ≥1.2 V
UVLO falling threshold235 / 250 / 265 mVMin / typ / max
UVLO rising threshold330 / 350 / 370 mVMin / typ / max; substantial hysteresis
Unused UVLOTie to VAUXDo not ground it in the always-enabled example
Down-conversion modeAutomatic when requiredSee efficiency and regulation conditions when input exceeds output
ShutdownLoad disconnectOutput capacitor can retain charge

Power-save bursts are expected at light load and must not be mistaken for a defective oscillator.

Layout and passive components

A switching converter needs a compact PCB

Scroll sideways to see all columns.

ParameterValueConditions / notes
Switching loopKeep inductor and power capacitors closeAvoid long breadboard-style loops in real hardware
FeedbackRoute away from switching nodesSense at the output capacitor; use a quiet ground return
Inductor2.2 µH in the worked circuitCheck peak/saturation current, DCR and core losses
CapacitorsCeramic with adequate effective capacitanceDC bias can reduce nominal capacitance considerably
Exposed padSolder to PGND copperAdd thermal vias and paste windows appropriate to the assembly
Footprint scopeCore land geometry providedPCB thermal extensions, solder mask and paste design remain assembly-specific

The illustrations explain connections, not a finished switching-power PCB layout.

Temperature and stress limits

Recommended operation and stress ratings are different

Scroll sideways to see all columns.

ParameterValueConditions / notes
Ambient operating range−40 to +85°CRecommended free-air range
Junction operating range−40 to +125°CRecommended range
Storage−65 to +150°CUnpowered
Voltage stress−0.3 to +7 V on specified electrical nodesAbsolute maximum; not an operating target
DRC junction-to-ambient41.2°C/WManufacturer reference board; actual layout changes temperature
Representative control current50 µA typical / 70 µA max at VOUTSee source test conditions; this is not the total loaded input current
Thermal shutdown140°C typical; 20°C typical hysteresisProtection threshold, not a normal operating temperature

Use real loss and thermal measurements for the intended load and input range.

Nominal 3.3 V circuit

Component choices and calculated load

Scroll sideways to see all columns.

ParameterValueConditions / notes
Input source3 V nominalDemonstration input, not the lowest operating corner
Inductor2.2 µH from input rail to L3Choose adequate saturation current and low DCR
Input capacitor10 µFClose to input / PGND
Output capacitor22 µFEffective value and loop stability must be checked
VAUX capacitor0.1 µF to GNDUse about 1 µF when output is below 2.5 V
Feedback divider1.12 MΩ top / 200 kΩ bottomNominal 3.3 V from the 0.5 V reference
Enable and modeEN6 to VIN; PS8 to GNDPower-save mode permitted
Unused undervoltage monitorUVLO7 to VAUX1Retains required control behavior
Test load33 Ω100 mA nominal; 0.33 W, use a suitable power rating

Example values require validation in the actual PCB, including startup, transient behavior and effective capacitance.

Connections by function

Select a pin for its function, connection guidance and electrical notes.

Supply2 pins

Regulated output1 pin

Switching nodes1 pin

Ground3 pins

Enable and mode2 pins

Feedback and monitoring2 pins

Read the conditions with every value

Typical values describe stated test conditions. Absolute maximum ratings are stress limits, not operating targets.

Official PDF datasheet

Component view