TPS7A3301 Reference Tables
Search the TPS7A3301 pin reference and manufacturer-referenced specification tables.
Pin reference
Signal names, electrical functions and connection guidance
Scroll within the table to see all columns and rows.
| Pin | Signal | Type | Function & connection |
|---|---|---|---|
| OUT | Negative output | Regulated negative supply rail.Connection guidanceJoin both OUT pins; bypass to ground with 47 µF. Use ceramic capacitors, or put a polarized capacitor’s positive terminal at ground. | |
| NC | No connection | No circuit connection is required.Connection guidanceLeave open in this example. | |
| FB | Feedback | Error-amplifier feedback input, approximately −1.175 V in regulation.Connection guidance332 kΩ from OUT to FB and 102 kΩ from FB to GND; 10 nF across the 332 kΩ resistor. | |
| NC | No connection | No circuit connection is required.Connection guidanceLeave open in this example. | |
| NC | No connection | No circuit connection is required.Connection guidanceLeave open in this example. | |
| NC | No connection | No circuit connection is required.Connection guidanceLeave open in this example. | |
| GND | Ground | Ground reference and heat-removal path.Connection guidanceConnect to ground copper; solder the exposed underside pad. | |
| NC | No connection | No circuit connection is required.Connection guidanceLeave open in this example. | |
| NC | No connection | No circuit connection is required.Connection guidanceLeave open in this example. | |
| NC | No connection | No circuit connection is required.Connection guidanceLeave open in this example. | |
| NC | No connection | No circuit connection is required.Connection guidanceLeave open in this example. | |
| NC | No connection | No circuit connection is required.Connection guidanceLeave open in this example. | |
| EN | Enable | Can be enabled by a sufficiently positive or negative control level.Connection guidanceTie to IN for the always-enabled negative-rail example. Ground disables; observe the specified positive and negative thresholds. | |
| NR/SS | Noise reduction / soft start | Reference filtering and output startup control.Connection guidanceConnect 1 µF ceramic to ground near the pin. | |
| IN | Negative input | Negative supply, referred to ground.Connection guidanceJoin pins 15 and 16 to −7 V; add 10 µF to ground. | |
| IN | Negative input | Negative supply, referred to ground.Connection guidanceJoin pins 15 and 16 to −7 V; add 10 µF to ground. | |
| NC | No connection | No circuit connection is required.Connection guidanceLeave open in this example. | |
| NC | No connection | No circuit connection is required.Connection guidanceLeave open in this example. | |
| NC | No connection | No circuit connection is required.Connection guidanceLeave open in this example. | |
| OUT | Negative output | Regulated negative supply rail.Connection guidanceJoin both OUT pins; bypass to ground with 47 µF. Use ceramic capacitors, or put a polarized capacitor’s positive terminal at ground. | |
| EP / GND | Exposed thermal pad | Ground reference and heat-removal path.Connection guidanceConnect to ground copper; solder the exposed underside pad. |
No pins match these filters. Try another signal name or reset the filters.
Electrical reference
Negative polarity is essential.
Scroll within the table to see all columns and rows.
| Parameter | Value | Conditions / notes |
|---|---|---|
| Recommended input | −35 to −3 V | −36 V is the absolute stress limit |
| Adjustable output | About −1.18 to −33 V | Maintain dropout headroom |
| Output capability | Up to 1 A | Observe junction temperature |
| Typical reference | −1.175 V | At the specified reference conditions |
| Typical dropout | 325 mV at 1 A | Maximum 800 mV under specified conditions |
| Typical noise | 16 µVrms | 10 Hz–100 kHz; manufacturer test circuit |
No specifications match. Try a parameter name or a unit.
Ratings depend on the conditions in the manufacturer PDF.
Approximately −5 V example
VOUT ≈ VREF × (1 + R1 / R2).
Scroll within the table to see all columns and rows.
| Parameter | Value | Conditions / notes |
|---|---|---|
| R1: OUT to FB | 332 kΩ | Use an appropriate precision tolerance |
| R2: FB to GND | 102 kΩ | Divider current about 11.5 µA |
| Nominal calculation | −1.175 × (1 + 332/102) ≈ −5.00 V | Excludes reference, resistor and FB-current errors |
| No-load divider requirement | At least 5 µA | Keep the lower resistor within the datasheet limit |
| Feed-forward capacitor | 10 nF across R1 | OUT to FB, not FB to GND |
No specifications match. Try a parameter name or a unit.
Verify the output tolerance and feedback-current contribution.
Filtering and enable
Use low-ESR capacitors close to the package.
Scroll within the table to see all columns and rows.
| Parameter | Value | Conditions / notes |
|---|---|---|
| Input capacitor | 10 µF | IN to GND |
| Output capacitor | 47 µF ceramic | OUT to GND; 10 µF minimum effective capacitance |
| NR/SS capacitor | 1 µF ceramic | NR/SS to GND |
| Enable | EN tied to IN | Negative enable is supported |
| Thermal pad | GND | Solder to the ground plane |
| Unused NC pins | Open | No intentional connection in the example |
No specifications match. Try a parameter name or a unit.
Polarized capacitors on negative rails need their positive terminal at ground.
Thermal example
−7 V input, approximately −5 V output and 0.25 A load.
Scroll within the table to see all columns and rows.
| Parameter | Value | Conditions / notes |
|---|---|---|
| Load power | About 1.25 W | 5 V magnitude × 0.25 A |
| Pass-stage loss | About 0.50 W | (7 − 5) V × 0.25 A |
| At 1 A | About 2 W pass loss | Check PCB thermal resistance |
| Additional losses | Ground-current power | Not included in the simple pass-loss calculation |
No specifications match. Try a parameter name or a unit.
The exposed pad is a heat path; the calculations are illustrative.
No matching rowsTry a pin name, parameter, unit or test condition, or reset the filters.