Skip to datasheet
Low-noise negative linear regulator

TPS7A3301 Specifications

Review TPS7A3301 electrical specifications, operating conditions and package details.

Key specifications

A quiet negative supply for precision analog circuits.

Output capability1 A Subject to thermal limits
Output noise16 µVrms 10 Hz–100 kHz; source conditions
Input range−35 to −3 V Recommended electrical range
Junction range−40–125 °C Recommended operation

Operating profile

Supply, signals and operating conditions

TPS7A3301 operating profile
ParameterValueConditions / notes
Example input−7 VGround is the positive reference
Example output≈ −5 VExternal feedback divider
Use these values with the stated grade and test conditions.

Package details

TPS7A3301RGWR · VQFN-20

Selected package
Selected TPS7A3301 physical package
PropertyDetails
ManufacturerTexas Instruments
Part numberTPS7A3301RGWR
PackageVQFN-20
Connections21 pins
MountingSMD
Lead pitch0.65 mm
Package codeVQFN-20
Thermal referenceSolder exposed pad to its specified net; design thermal vias and paste for assembly.

Electrical reference

Negative polarity is essential.

Scroll sideways to see all columns.

ParameterValueConditions / notes
Recommended input−35 to −3 V−36 V is the absolute stress limit
Adjustable outputAbout −1.18 to −33 VMaintain dropout headroom
Output capabilityUp to 1 AObserve junction temperature
Typical reference−1.175 VAt the specified reference conditions
Typical dropout325 mV at 1 AMaximum 800 mV under specified conditions
Typical noise16 µVrms10 Hz–100 kHz; manufacturer test circuit

Ratings depend on the conditions in the manufacturer PDF.

Approximately −5 V example

VOUT ≈ VREF × (1 + R1 / R2).

Scroll sideways to see all columns.

ParameterValueConditions / notes
R1: OUT to FB332 kΩUse an appropriate precision tolerance
R2: FB to GND102 kΩDivider current about 11.5 µA
Nominal calculation−1.175 × (1 + 332/102) ≈ −5.00 VExcludes reference, resistor and FB-current errors
No-load divider requirementAt least 5 µAKeep the lower resistor within the datasheet limit
Feed-forward capacitor10 nF across R1OUT to FB, not FB to GND

Verify the output tolerance and feedback-current contribution.

Filtering and enable

Use low-ESR capacitors close to the package.

Scroll sideways to see all columns.

ParameterValueConditions / notes
Input capacitor10 µFIN to GND
Output capacitor47 µF ceramicOUT to GND; 10 µF minimum effective capacitance
NR/SS capacitor1 µF ceramicNR/SS to GND
EnableEN tied to INNegative enable is supported
Thermal padGNDSolder to the ground plane
Unused NC pinsOpenNo intentional connection in the example

Polarized capacitors on negative rails need their positive terminal at ground.

Thermal example

−7 V input, approximately −5 V output and 0.25 A load.

Scroll sideways to see all columns.

ParameterValueConditions / notes
Load powerAbout 1.25 W5 V magnitude × 0.25 A
Pass-stage lossAbout 0.50 W(7 − 5) V × 0.25 A
At 1 AAbout 2 W pass lossCheck PCB thermal resistance
Additional lossesGround-current powerNot included in the simple pass-loss calculation

The exposed pad is a heat path; the calculations are illustrative.

Connections by function

Select a pin for its function, connection guidance and electrical notes.

Supply4 pins

Not connected12 pins

Feedback / filtering2 pins

Ground2 pins

Enable1 pin

Read the conditions with every value

Typical values describe stated test conditions. Absolute maximum ratings are stress limits, not operating targets.

Official PDF datasheet

Component view