Skip to datasheet
Adjustable single-inductor buck-boost converter

TPS63000 Specifications

Review TPS63000 electrical specifications, operating conditions and package details.

Key specifications

Keep a regulated rail as the battery moves above and below the output voltage. The inductor carries switching current; the feedback network senses the output and the controller adjusts energy transfer.

Operating input1.8–5.5 V 1.9 V minimum startup input
Adjustable output1.2–5.5 V Headroom, power and loop constraints apply
Current-limit figure1.8 A Typical switch limit; not an output-current rating
Recommended ambient−40–85 °C · junction range is separate

Operating profile

Supply, signals and operating conditions

TPS63000 operating profile
ParameterValueConditions / notes
Selected packageVSON-10 + EPTPS63000DRCR
Exposed pad 11PGNDSolder to power-ground copper
Example output3.3 V1.12 MΩ / 200 kΩ divider
Use these values with the stated grade and test conditions.

Package details

TPS63000DRCR · VSON-10 + EP

Selected package
Selected TPS63000 physical package
PropertyDetails
ManufacturerTexas Instruments
Part numberTPS63000DRCR
PackageVSON-10 + EP
Connections11 pins
MountingSMD
Lead pitch0.50 mm
Package codeDRC
Thermal referenceExposed pad 11 to PGND; solder to ground copper

Package connections

Numbered physical contacts and underside pad

Scroll sideways to see all columns.

ParameterValueConditions / notes
1 · VOUTRegulated outputConnect output capacitors and the feedback divider.
2 · L2Inductor switching nodeConnect one end of the 2.2 µH inductor; other end to L1 pin 4.
3 · PGNDPower groundReturn the high-current input/output capacitor loops here.
4 · L1Inductor switching nodeConnect the other end of the inductor from L2 pin 2.
5 · VINPower supply inputBypass to PGND locally with 10 µF in the example.
6 · ENEnable inputTie high to enable; low disables. Do not leave floating.
7 · PS/SYNCMode / clock inputLow permits power save, high forces fixed-frequency operation; also accepts a synchronization clock.
8 · VINAControl supply inputUse the example 100 Ω from VIN and 0.1 µF to GND filter.
9 · GNDControl groundJoin power ground at a quiet local connection.
10 · FBOutput feedbackConnect the junction of 1.12 MΩ from VOUT and 200 kΩ to GND.
11 · PGND / EPExposed thermal padSolder to PGND copper; underside pad is numbered 11 in this footprint.

Leadless contacts are plated lands, not long protruding legs. Pad 11 represents the soldered underside ground pad.

Supply and electrical characteristics

Read conditions alongside every rating

Scroll sideways to see all columns.

ParameterValueConditions / notes
Input operating range1.8–5.5 VStartup specification begins at 1.9 V
Adjustable output1.2–5.5 VUse the external FB divider
Feedback voltage495 / 500 / 505 mVMin / typ / max with PS/SYNC high
Oscillator1.25 MHz minimum; 1.5 MHz typicalElectrical characteristics table
Synchronization range1.25–1.8 MHzApplied to PS/SYNC
Switch current limit1.6 / 1.8 / 2.0 AMin / typ / max at VIN=VINA=3.6 V and TA=25°C
Output-current headline in buckUp to 1.2 A at 3.3 VVIN 3.6–5.5 V; practical thermal and component limits remain
Output-current headline in boostUp to 800 mA at 3.3 VVIN above 2.4 V; not at every input voltage

A current limit is not a guarantee of output current at every input voltage.

Control modes and startup

Define every logic input

Scroll sideways to see all columns.

ParameterValueConditions / notes
EN low / highDisabled / enabledLow ≤0.4 V; high ≥1.2 V
PS/SYNC lowPower save permittedBurst-like light-load activity is expected
PS/SYNC highForced fixed-frequency operationUseful when predictable switching is preferred
PS/SYNC clockExternal synchronizationObserve the specified frequency and logic ranges
Undervoltage lockout1.7 V typical falling1.5–1.8 V range at VINA
Shutdown current0.1 µA typical; 1 µA maximumVIN=VINA=3.6 V, EN=0 V
Shutdown load disconnectOutput disconnected from inputDoes not mean the output capacitor is instantly discharged

Power-save bursts are expected at light load and must not be mistaken for a defective oscillator.

Layout and passive components

A switching converter needs a compact PCB

Scroll sideways to see all columns.

ParameterValueConditions / notes
Switching loopKeep inductor and power capacitors closeAvoid long breadboard-style loops in real hardware
FeedbackRoute away from switching nodesSense at the output capacitor; use a quiet ground return
Inductor2.2 µH in the worked circuitCheck peak/saturation current, DCR and core losses
CapacitorsCeramic with adequate effective capacitanceDC bias can reduce nominal capacitance considerably
Exposed padSolder to PGND copperAdd thermal vias and paste windows appropriate to the assembly
Footprint scopeCore land geometry providedPCB thermal extensions, solder mask and paste design remain assembly-specific

The illustrations explain connections, not a finished switching-power PCB layout.

Temperature and stress limits

Recommended operation and stress ratings are different

Scroll sideways to see all columns.

ParameterValueConditions / notes
Ambient operating range−40 to +85°CRecommended free-air range
Junction operating range−40 to +125°CRecommended range
Storage−65 to +150°CUnpowered
Voltage stress−0.3 to +7 V on specified electrical nodesAbsolute maximum; not an operating target
DRC junction-to-ambient46.8°C/WManufacturer reference board; actual layout changes temperature
Representative control current40 µA typical / 50 µA max at VINASee source test conditions; this is not the total loaded input current
Thermal shutdown140°C typical; 20°C typical hysteresisProtection threshold, not a normal operating temperature

Use real loss and thermal measurements for the intended load and input range.

Nominal 3.3 V circuit

Component choices and calculated load

Scroll sideways to see all columns.

ParameterValueConditions / notes
VIN source2.0–5.5 V for the demonstrationIncludes startup headroom; 3.7 V nominal example
Inductor2.2 µH between L1 pin 4 and L2 pin 2Low DCR and adequate saturation/peak-current rating
Input capacitor10 µFClose to VIN5 / PGND3
Output capacitors2 × 10 µFClose to VOUT1 / PGND3; consider effective capacitance
Control filter100 Ω to VINA8; 0.1 µF to GND9Separate quiet control supply
Feedback1.12 MΩ top / 200 kΩ bottomVOUT = 0.5 × (1 + 1.12 M / 200 k) = 3.3 V
Feedforward capacitorApproximately 2 pF across the top resistor2.2 µs / 1.12 MΩ ≈ 1.96 pF; layout parasitics matter
Mode / loadPS/SYNC7 to GND; 33 Ω load100 mA nominal, 0.33 W load; use suitable resistor rating

Example values require validation in the actual PCB, including startup, transient behavior and effective capacitance.

Connections by function

Select a pin for its function, connection guidance and electrical notes.

Regulated output1 pin

Switching nodes2 pins

Ground3 pins

Supply2 pins

Enable and mode2 pins

Feedback and monitoring1 pin

Read the conditions with every value

Typical values describe stated test conditions. Absolute maximum ratings are stress limits, not operating targets.

Official PDF datasheet

Component view