ACS712 Reference Tables
Search the ACS712 pin reference and manufacturer-referenced specification tables.
Pin reference
Signal names, electrical functions and connection guidance
Scroll within the table to see all columns and rows.
| Pin | Signal | Type | Function & connection |
|---|---|---|---|
| IP+ | Primary current input | First positive-side contact of the internal copper current path.Connection guidanceJoin pin 2 and the source side of the measured circuit. Use both contacts and adequate copper. This is not a logic pin. | |
| IP+ | Primary current input | Second positive-side contact; internally joined with pin 1.Connection guidanceJoin pin 1 with a suitably wide copper area. | |
| IP− | Primary current output | First negative-side contact of the sampled current path.Connection guidanceJoin pin 4 and the load side of the circuit. | |
| IP− | Primary current output | Second negative-side contact; internally joined with pin 3.Connection guidanceJoin pin 3; positive current flows from pins 1/2 to 3/4. | |
| GND | Signal ground | Reference for the sensor supply and output.Connection guidanceConnect to the ADC/controller ground. The Hall signal side is electrically isolated from the primary conductor inside the IC. | |
| FILTER | Bandwidth adjustment | External capacitor to ground forms a low-pass with the internal filter resistance.Connection guidanceUse 1 nF to GND in the example. Larger capacitance lowers bandwidth and noise; it does not remove offset error. | |
| VIOUT | Analog current signal | Ratiometric voltage around VCC/2 at zero current.Connection guidanceConnect to a high-impedance ADC with a compatible input range. The example uses the ±5 A variant, 185 mV/A typical at 5 V. | |
| VCC | Supply | Powers the Hall electronics.Connection guidanceUse regulated 5 V with 100 nF to GND. Operating supply 4.5–5.5 V; not a 3.3 V supply device. |
No pins match these filters. Try another signal name or reset the filters.
Range and sensitivity variants
Same pinout, different transfer gain
Scroll within the table to see all columns and rows.
| Parameter | Value | Conditions / notes |
|---|---|---|
| ACS712-05B | ±5 A; 185 mV/A typical | 180–190 mV/A at 25°C |
| ACS712-20A | ±20 A; 100 mV/A typical | Do not use the 05B divisor |
| ACS712-30A | ±30 A; 66 mV/A typical | Lower voltage change per ampere |
| Selected page example | ACS712ELCTR-05B-T | SOIC-8; −40 to +85°C |
| Positive direction | IP+ → IP− | Output rises above its zero-current level |
| Negative direction | IP− → IP+ | Output falls below its zero-current level |
No specifications match. Try a parameter name or a unit.
The sensitivity variant must match the purchased IC marking or module bill of materials.
Electrical operating values
5 V and specified test conditions
Scroll within the table to see all columns and rows.
| Parameter | Value | Conditions / notes |
|---|---|---|
| Supply | 4.5–5.5 V | 5 V nominal |
| Supply current | 10 mA typical; 13 mA maximum | Output open, VCC 5 V |
| Zero-current output | VCC × 0.5 nominal | Measure the actual baseline |
| Primary resistance | 1.2 mΩ typical | At 25°C |
| Output resistive load | At least 4.7 kΩ | Higher impedance preferred |
| Output capacitive load | At most 10 nF | At VIOUT; separate from FILTER capacitance |
| Bandwidth | 80 kHz typical | Stated 1 nF filter/test conditions |
No specifications match. Try a parameter name or a unit.
An 8 V absolute maximum is a stress rating, not an operating supply.
Filtering and sampling
Trade bandwidth for lower noise
Scroll within the table to see all columns and rows.
| Parameter | Value | Conditions / notes |
|---|---|---|
| Internal filter resistance | 1.7 kΩ typical | Works with CF at pin 6 |
| Example CF | 1 nF | Manufacturer typical application |
| RC pole approximation | 1 / (2π × 1.7 kΩ × CF) | Overall device bandwidth also limits response |
| CF 47 nF | Approximately 2 kHz response | 05B noise test uses this filtering |
| 05B noise example | 21 mV peak-to-peak typical | 47 nF filter; stated 2 kHz bandwidth |
| ADC sampling | Use appropriate anti-aliasing and averaging | Do not sample noise and call it changing load current |
No specifications match. Try a parameter name or a unit.
Averages can reduce random noise but do not correct systematic offset or sensitivity errors.
Ideal 05B output at 5 V
VOUT = 2.5 V + I × 0.185 V/A
Scroll within the table to see all columns and rows.
| Parameter | Value | Conditions / notes |
|---|---|---|
| −5 A | 1.575 V | Ideal nominal transfer |
| −1 A | 2.315 V | Reverse current |
| 0 A | 2.500 V | Use measured zero in software |
| +1 A | 2.685 V | Illustrated low-voltage load |
| +5 A | 3.425 V | Selected nominal positive endpoint |
| Conversion formula | I = (VOUT − VZERO) / sensitivity | Sensitivity follows supply voltage and variant |
No specifications match. Try a parameter name or a unit.
A 3.3 V ADC cannot directly accept every output level of this 5 V sensor; use a suitable interface.
Accuracy and error sources
Separate resolution from absolute accuracy
Scroll within the table to see all columns and rows.
| Parameter | Value | Conditions / notes |
|---|---|---|
| 05B total output error | ±1.5% at 25°C | Percentage of the ±5 A full-scale test point; filtered output |
| 05B sensitivity limits | 180–190 mV/A | At 25°C |
| Ratiometric response | Zero level and sensitivity scale with VCC | A common supply-derived ADC reference can help |
| Offset drift | Changes with temperature | Re-zero under valid no-current conditions |
| External magnetic fields | Can disturb the result | Separate nearby high-current paths or magnets |
| Quantization | Depends on ADC reference and resolution | Sensor noise can exceed one ADC count |
No specifications match. Try a parameter name or a unit.
The page example is nominal arithmetic, not a guaranteed ±1.5% reading at every current.
Low-voltage 1 A teaching circuit
Physical current and signal paths
Scroll within the table to see all columns and rows.
| Parameter | Value | Conditions / notes |
|---|---|---|
| Primary source | 12 V | Low-voltage bench supply |
| Load | 12 Ω, at least 20 W | Approximately 12 W dissipation |
| IP+ | Pins 1 and 2 joined to source | Both pads carry current |
| IP− | Pins 3 and 4 joined to load | Both pads carry current |
| Signal-side supply | 5 V; 100 nF bypass | Pin 8 to pin 5 |
| Filter | 1 nF from pin 6 to GND | Keep short |
| Output | Pin 7 to a 5 V-compatible ADC | Approximate 2.685 V at +1 A |
No specifications match. Try a parameter name or a unit.
The primary circuit need not share signal ground for sensing; the drawing keeps the domains distinct.
Package, copper and isolation
Footprint is only part of the system design
Scroll within the table to see all columns and rows.
| Parameter | Value | Conditions / notes |
|---|---|---|
| LC package | SOIC-8, 4.90 × 3.90 mm body | 1.27 mm lead pitch; 6.0 mm span |
| Reference copper lands | 1.75 × 0.65 mm | 5.60 mm pad-row centers |
| Current contacts | 1/2 and 3/4 paired | Use adequate copper and thermal design |
| Isolation withstand | 2.4 kVrms, specified test | Not a blanket continuous working-voltage rating |
| System isolation | Depends on clearances, PCB and assembly | Follow the manufacturer certification conditions |
| Primary-path heating | I² × conductor resistance | Temperature and copper affect usable current |
No specifications match. Try a parameter name or a unit.
This page demonstrates a low-voltage circuit. A generic footprint download does not certify a board for hazardous voltages.
No matching rowsTry a pin name, parameter, unit or test condition, or reset the filters.