ACS712 Specifications
Review ACS712 electrical specifications, operating conditions and package details.
Key specifications
Load current creates a magnetic field in the Hall element. Offset cancellation and amplification produce a supply-ratiometric analog voltage.
Package details
ACS712ELCTR-05B-T · SOIC-8
| Property | Details |
|---|---|
| Manufacturer | Allegro MicroSystems |
| Part number | ACS712ELCTR-05B-T |
| Package | SOIC-8 |
| Connections | 8 pins |
| Mounting | SMD |
| Lead pitch | 1.27 mm |
| Package code | SOIC-8 |
| Thermal reference | See operating and package limits |
Range and sensitivity variants
Same pinout, different transfer gain
Scroll sideways to see all columns.
| Parameter | Value | Conditions / notes |
|---|---|---|
| ACS712-05B | ±5 A; 185 mV/A typical | 180–190 mV/A at 25°C |
| ACS712-20A | ±20 A; 100 mV/A typical | Do not use the 05B divisor |
| ACS712-30A | ±30 A; 66 mV/A typical | Lower voltage change per ampere |
| Selected page example | ACS712ELCTR-05B-T | SOIC-8; −40 to +85°C |
| Positive direction | IP+ → IP− | Output rises above its zero-current level |
| Negative direction | IP− → IP+ | Output falls below its zero-current level |
No specifications match. Try a parameter name or a unit.
The sensitivity variant must match the purchased IC marking or module bill of materials.
Electrical operating values
5 V and specified test conditions
Scroll sideways to see all columns.
| Parameter | Value | Conditions / notes |
|---|---|---|
| Supply | 4.5–5.5 V | 5 V nominal |
| Supply current | 10 mA typical; 13 mA maximum | Output open, VCC 5 V |
| Zero-current output | VCC × 0.5 nominal | Measure the actual baseline |
| Primary resistance | 1.2 mΩ typical | At 25°C |
| Output resistive load | At least 4.7 kΩ | Higher impedance preferred |
| Output capacitive load | At most 10 nF | At VIOUT; separate from FILTER capacitance |
| Bandwidth | 80 kHz typical | Stated 1 nF filter/test conditions |
No specifications match. Try a parameter name or a unit.
An 8 V absolute maximum is a stress rating, not an operating supply.
Filtering and sampling
Trade bandwidth for lower noise
Scroll sideways to see all columns.
| Parameter | Value | Conditions / notes |
|---|---|---|
| Internal filter resistance | 1.7 kΩ typical | Works with CF at pin 6 |
| Example CF | 1 nF | Manufacturer typical application |
| RC pole approximation | 1 / (2π × 1.7 kΩ × CF) | Overall device bandwidth also limits response |
| CF 47 nF | Approximately 2 kHz response | 05B noise test uses this filtering |
| 05B noise example | 21 mV peak-to-peak typical | 47 nF filter; stated 2 kHz bandwidth |
| ADC sampling | Use appropriate anti-aliasing and averaging | Do not sample noise and call it changing load current |
No specifications match. Try a parameter name or a unit.
Averages can reduce random noise but do not correct systematic offset or sensitivity errors.
Ideal 05B output at 5 V
VOUT = 2.5 V + I × 0.185 V/A
Scroll sideways to see all columns.
| Parameter | Value | Conditions / notes |
|---|---|---|
| −5 A | 1.575 V | Ideal nominal transfer |
| −1 A | 2.315 V | Reverse current |
| 0 A | 2.500 V | Use measured zero in software |
| +1 A | 2.685 V | Illustrated low-voltage load |
| +5 A | 3.425 V | Selected nominal positive endpoint |
| Conversion formula | I = (VOUT − VZERO) / sensitivity | Sensitivity follows supply voltage and variant |
No specifications match. Try a parameter name or a unit.
A 3.3 V ADC cannot directly accept every output level of this 5 V sensor; use a suitable interface.
Accuracy and error sources
Separate resolution from absolute accuracy
Scroll sideways to see all columns.
| Parameter | Value | Conditions / notes |
|---|---|---|
| 05B total output error | ±1.5% at 25°C | Percentage of the ±5 A full-scale test point; filtered output |
| 05B sensitivity limits | 180–190 mV/A | At 25°C |
| Ratiometric response | Zero level and sensitivity scale with VCC | A common supply-derived ADC reference can help |
| Offset drift | Changes with temperature | Re-zero under valid no-current conditions |
| External magnetic fields | Can disturb the result | Separate nearby high-current paths or magnets |
| Quantization | Depends on ADC reference and resolution | Sensor noise can exceed one ADC count |
No specifications match. Try a parameter name or a unit.
The page example is nominal arithmetic, not a guaranteed ±1.5% reading at every current.
Low-voltage 1 A teaching circuit
Physical current and signal paths
Scroll sideways to see all columns.
| Parameter | Value | Conditions / notes |
|---|---|---|
| Primary source | 12 V | Low-voltage bench supply |
| Load | 12 Ω, at least 20 W | Approximately 12 W dissipation |
| IP+ | Pins 1 and 2 joined to source | Both pads carry current |
| IP− | Pins 3 and 4 joined to load | Both pads carry current |
| Signal-side supply | 5 V; 100 nF bypass | Pin 8 to pin 5 |
| Filter | 1 nF from pin 6 to GND | Keep short |
| Output | Pin 7 to a 5 V-compatible ADC | Approximate 2.685 V at +1 A |
No specifications match. Try a parameter name or a unit.
The primary circuit need not share signal ground for sensing; the drawing keeps the domains distinct.
Package, copper and isolation
Footprint is only part of the system design
Scroll sideways to see all columns.
| Parameter | Value | Conditions / notes |
|---|---|---|
| LC package | SOIC-8, 4.90 × 3.90 mm body | 1.27 mm lead pitch; 6.0 mm span |
| Reference copper lands | 1.75 × 0.65 mm | 5.60 mm pad-row centers |
| Current contacts | 1/2 and 3/4 paired | Use adequate copper and thermal design |
| Isolation withstand | 2.4 kVrms, specified test | Not a blanket continuous working-voltage rating |
| System isolation | Depends on clearances, PCB and assembly | Follow the manufacturer certification conditions |
| Primary-path heating | I² × conductor resistance | Temperature and copper affect usable current |
No specifications match. Try a parameter name or a unit.
This page demonstrates a low-voltage circuit. A generic footprint download does not certify a board for hazardous voltages.
Connections by function
Select a pin for its function, connection guidance and electrical notes.