ADXL345 Reference Tables
Search the ADXL345 pin reference and manufacturer-referenced specification tables.
Pin reference
Signal names, electrical functions and connection guidance
Scroll within the table to see all columns and rows.
| Pin | Signal | Type | Function & connection |
|---|---|---|---|
| VDD I/O | Logic supply | Powers the digital interface.Connection guidanceUse the 2.5 V logic rail with a local 100 nF ceramic capacitor. 1.7 V to VS; bus pull-ups use this rail. | |
| GND | Ground | Ground connection.Connection guidanceJoin pins 4 and 5 and controller ground. | |
| RESERVED | Reserved | Manufacturer-defined reserved terminal.Connection guidanceConnect to VS or leave open; the example uses VS. | |
| GND | Ground | Ground connection.Connection guidanceConnect to the ground plane. | |
| GND | Ground | Ground connection.Connection guidanceConnect to the ground plane. | |
| VS | Sensor supply | Powers the sensing electronics.Connection guidanceUse 2.5 V with a local 1 µF tantalum capacitor. Recommended range 2.0–3.6 V. | |
| CS | Interface select | Low selects SPI transactions; high enables I²C operation.Connection guidanceTie to VDD I/O for the I²C example. | |
| INT1 | Interrupt output | Programmable data-ready, activity, tap or FIFO interrupt.Connection guidanceOptional host input; unused output may remain open. | |
| INT2 | Interrupt output | Second configurable interrupt route.Connection guidanceOptional host input; leave open if unused. | |
| NC | No connection | No internal connection.Connection guidanceLeave open. | |
| RESERVED | Reserved | Manufacturer-defined reserved terminal.Connection guidanceConnect to ground or leave open; the example uses GND. | |
| SDO / ALTADDR | SPI output / address | SPI data output or I²C address selection.Connection guidanceTie low for address 0x53; high selects 0x1D. | |
| SDA / SDI / SDIO | Serial data | I²C bidirectional data or SPI data input/shared data.Connection guidanceHost SDA with a 4.7 kΩ pull-up to VDD I/O. | |
| SCL / SCLK | Serial clock | Clock from the I²C or SPI controller.Connection guidanceHost SCL with a pull-up to VDD I/O in I²C mode. |
No pins match these filters. Try another signal name or reset the filters.
Power and operating limits
Recommended operation, not survival ratings
Scroll within the table to see all columns and rows.
| Parameter | Value | Conditions / notes |
|---|---|---|
| VS | 2.0–3.6 V | 2.5 V used for the reference example |
| VDD I/O | 1.7 V to VS | Use compatible host logic and pull-ups |
| Temperature | −40 to +85°C | Operating range |
| Measurement current | 140 µA typical | Normal mode, ODR ≥100 Hz, specified conditions |
| Standby current | 0.1 µA typical | Not the current while measuring |
| Low-power mode | As low as 23 µA typical | Specific low-power rate setting; not all modes |
| Shock survival | 10,000 g | Survival rating, not an acceleration measurement range |
No specifications match. Try a parameter name or a unit.
Keep supply-domain sequencing and absolute maximum limits in mind when interfacing a separately powered controller.
Range, resolution and scale
Full-resolution and fixed-resolution modes differ
Scroll within the table to see all columns and rows.
| Parameter | Value | Conditions / notes |
|---|---|---|
| Full resolution | About 3.9 mg/LSB | Nominal 256 LSB/g across selectable ranges |
| ±2 g | 10 useful bits | Full-resolution or fixed 10-bit mode |
| ±4 g | 11 useful bits in full-resolution mode | Fixed 10-bit scale is 128 LSB/g nominal |
| ±8 g | 12 useful bits in full-resolution mode | Fixed 10-bit scale is 64 LSB/g nominal |
| ±16 g | 13 useful bits in full-resolution mode | Fixed 10-bit scale is 32 LSB/g nominal |
| Result representation | Signed two’s complement in a 16-bit word | Default right justification in this example |
| Sensitivity specification | 230–282 LSB/g at ±2 g | Typical 256, stated 2.5 V test conditions |
No specifications match. Try a parameter name or a unit.
Do not confuse the 16-bit register container with 16-bit measurement resolution.
Core register map
An initial configuration and coherent burst read
Scroll within the table to see all columns and rows.
| Parameter | Value | Conditions / notes |
|---|---|---|
| 0x00 · DEVID | 0xE5 | Read-only device identification |
| 0x2C · BW_RATE | 0x0A | 100 Hz output, normal power |
| 0x31 · DATA_FORMAT | 0x08 | Full resolution, ±2 g, right justified |
| 0x2D · POWER_CTL | 0x08 | Measurement enabled |
| 0x32–0x37 · axis data | X0, X1, Y0, Y1, Z0, Z1 | Low byte first for each signed axis |
| 0x2E / 0x2F / 0x30 | INT_ENABLE / INT_MAP / INT_SOURCE | Configure and identify interrupts |
| 0x38 / 0x39 | FIFO_CTL / FIFO_STATUS | Configure buffering and read occupancy |
No specifications match. Try a parameter name or a unit.
Set format/rate before enabling measurement; use the manufacturer’s detailed register descriptions for other features.
I²C, SPI and buffering
Address and transaction rules
Scroll within the table to see all columns and rows.
| Parameter | Value | Conditions / notes |
|---|---|---|
| I²C selection | CS tied high | Never leave CS floating |
| I²C address | 0x53 with ALTADDR low; 0x1D high | Seven-bit address |
| I²C clock | Up to 400 kHz | At 100 kHz, keep ODR at 200 Hz or lower; at 400 kHz, 800 Hz or lower |
| SPI | 3-wire or 4-wire, up to 5 MHz | MSB first; clock polarity high and sample rising |
| FIFO | 32 samples; bypass, FIFO, stream, trigger modes | Read all axis bytes together |
| Interrupt routing | INT1 or INT2 | Data-ready, watermark, overrun, tap, activity and free-fall |
| Fresh read | Wait for data-ready | Avoid reading faster and treating repeats as new motion |
No specifications match. Try a parameter name or a unit.
For 1600/3200 Hz output the data format and interface timing need particular attention; consult the reference.
2.5 V I²C wiring example
Bare IC with deliberate reserved-pin handling
Scroll within the table to see all columns and rows.
| Parameter | Value | Conditions / notes |
|---|---|---|
| VS6 | 2.5 V with 1 µF tantalum | Place bypass at the terminal |
| VDD I/O1 | 2.5 V with 100 nF ceramic | Separate local bypass |
| GND2,4,5 | Common ground plane | Low-impedance return |
| CS7 | VDD I/O | Select I²C |
| ALTADDR12 | GND | Select 0x53 |
| SDA13 / SCL14 | Host I²C with 4.7 kΩ pull-ups | Pull up to VDD I/O |
| Reserved3 / Reserved11 | VS / GND in this example | Manufacturer also permits leaving these open |
| NC10 / INT1 / INT2 | Open if unused | NC is not a ground pin |
No specifications match. Try a parameter name or a unit.
A 5 V microcontroller needs suitable level translation. The bare sensor is not a 5 V module.
Signed readings and calibration
Illustrative static examples at nominal sensitivity
Scroll within the table to see all columns and rows.
| Parameter | Value | Conditions / notes |
|---|---|---|
| 00 01, low byte first | 0x0100 = +256 | Approximately +1 g |
| 80 FF, low byte first | 0xFF80 = −128 | Approximately −0.5 g |
| Acceleration | g ≈ signed_count / 256 | Nominal full-resolution scale |
| Stationary top up | X≈0, Y≈0, Z≈+1 g | Offset and alignment affect real readings |
| Calibration | Measure offsets and scale per axis | Separate static gravity from dynamic acceleration |
| Operation at 3.3 V | Sensitivity and offset shift | Do not silently substitute the 2.5 V nominal calibration |
No specifications match. Try a parameter name or a unit.
Illustrations are calculations rather than live measurements. The datasheet describes voltage-dependent scale changes.
Mechanical and layout guidance
Mounting quality matters
Scroll within the table to see all columns and rows.
| Parameter | Value | Conditions / notes |
|---|---|---|
| Package | 14-terminal LGA, 3 × 5 × 1 mm | CC-14-1 |
| Side pitch | 0.80 mm | Six pads on each long side, one at each end |
| Pin numbering | 1–6 left, 7 bottom, 8–13 right, 14 top | Top view |
| Contacts | Au over Ni underside lands | The package has no long projecting DIP leads |
| Placement | Near a rigid PCB mounting point | Avoid unsupported vibrating PCB areas |
| Filtering | Match bandwidth to the measurement | Bandwidth is nominally half the output data rate |
No specifications match. Try a parameter name or a unit.
Do not use survival shock ratings or cartoon motion as a substitute for the measurement limits.
No matching rowsTry a pin name, parameter, unit or test condition, or reset the filters.