Skip to datasheet
Digital barometric pressure sensor

BMP388 Reference Tables

Search the BMP388 pin reference and manufacturer-referenced specification tables.

Selected packageLGA-10BMP388
Physical connections10 pinsPackage-specific numbering
Reference collection7 tables44 parameters & pin functions

Pin reference

Signal names, electrical functions and connection guidance

LGA-10
Physical pin numbers10 pins

Scroll within the table to see all columns and rows.

BMP388 pin functions and connections
PinSignalTypeFunction & connection
VDDIOSupplyDigital interface supply.
Connection guidance

Connect to 1.2–3.6 V and bypass with 100 nF.

3.3 V in the example; the bare IC is not 5 V tolerant.

SCKInputSPI clock or I²C SCL.
Connection guidance

Connect to the host clock; use an I²C pullup to VDDIO.

VSSReturnGround connection.
Connection guidance

Join to the common ground plane.

SDIBidirectionalSPI data input or I²C SDA.
Connection guidance

Connect to MOSI in four-wire SPI, or SDA with a pullup in I²C.

SDOOutput / addressSPI output or I²C address selection.
Connection guidance

I²C: ground selects 0x76; VDDIO selects 0x77.

Do not float in I²C; leave unconnected in three-wire SPI.

CSBInputActive-low SPI chip select and protocol selection.
Connection guidance

Hold at VDDIO from power-up for I²C.

Once driven low, I²C stays disabled until a power-on reset.

INTOutputConfigurable data-ready or FIFO interrupt.
Connection guidance

Connect to a host interrupt input, or leave unconnected.

VSSReturnGround connection.
Connection guidance

Join to the common ground plane.

VSSReturnGround connection.
Connection guidance

Join to the common ground plane.

VDDSupplyAnalog sensor supply.
Connection guidance

Connect to 1.65–3.6 V and bypass with 100 nF.

LGA-10 · Top view · pin 1 upper right · Select a pin number to open its interactive pinout.

Supplies and interface

Bare-sensor operating limits

Manufacturer-referenced values7 parameters

Scroll within the table to see all columns and rows.

ParameterValueConditions / notes
VDD sensor rail1.65–3.6 VMaximum specified supply ripple 50 mV peak-to-peak
VDDIO logic rail1.2–3.6 VPull up the bus to this rail
Sleep current2 µA typicalVDD = VDDIO, 1.8–3.6 V
Pressure-conversion current700 µA typical; 800 µA maximumNot the low-rate average current
Startup2 ms maximumAfter both supplies meet the stated thresholds
I²C / SPI clocksUp to 3.4 MHz / 10 MHzObserve the timing conditions; example uses ordinary I²C
Bypass / pullups100 nF per rail; 4.7 kΩ example pullupsChoose bus resistors for capacitance and speed

Operating limits are not absolute maximum stress ratings.

Pressure and temperature

Accuracy depends on conditions

Manufacturer-referenced values8 parameters

Scroll within the table to see all columns and rows.

ParameterValueConditions / notes
Pressure range300–1250 hPaSee full-accuracy conditions
Typical absolute pressure error±0.50 hPa300–1100 hPa, −20°C to +65°C
Typical relative pressure error±0.08 hPa900–1100 hPa, 25°C to 40°C; per 10 kPa steps
Temperature operating range−40°C to +85°CFull-accuracy temperature range 0°C to 65°C
Typical temperature error±0.3°C at 25°C±0.50°C over 0°C to 65°C
Temperature meaningSensor/board temperatureSelf-heating and PCB heat can raise it above ambient
Maximum sample rate200 HzOnly with settings whose conversion time fits
Typical pressure noise1.2 Pa full bandwidth; 0.03 Pa filteredHighest resolution; the lowest noise is not available at every bandwidth

Noise, resolution and absolute accuracy are different quantities.

Protocol and pins

I²C example at seven-bit address 0x76

Manufacturer-referenced values8 parameters

Scroll within the table to see all columns and rows.

ParameterValueConditions / notes
I²C clock / data2 SCK / 4 SDIUse these as SCL / SDA
Address selection5 SDO low → 0x76; high → 0x77Do not leave floating
I²C protocol selection6 CSB held high at power-onPulling it low locks SPI until the next power-on reset
SPI connections2 clock, 4 MOSI, 5 MISO, 6 CSBModes 0 or 3; SDO unconnected for three-wire mode
SPI read framingRead bit in command, then one dummy byteFollowing bytes are register data
Interrupt7 INTOptional data-ready or FIFO notification
Ground contacts3, 8 and 9 VSSConnect all three
Supply contacts1 VDDIO and 10 VDDBypass both locally

Package orientation matters: the top-view pin-one marker is upper right.

Measurement control

Register addresses are hexadecimal

Manufacturer-referenced values8 parameters

Scroll within the table to see all columns and rows.

ParameterValueConditions / notes
CHIP_ID / ERR_REG / STATUS0x00 / 0x02 / 0x03Expected ID 0x50; check errors and data-ready flags
Pressure and temperature burst0x04–0x09Pressure first; each unsigned 24-bit word is least-significant byte first
PWR_CTRL0x1BPressure enable bit 0, temperature bit 1, mode bits 5:4
OSR0x1CPressure bits 2:0; temperature bits 5:3; ×1 to ×32
ODR0x1DRate = 200 / 2^odr_sel Hz; valid selection 0–17
CONFIG0x1FIIR coefficient in bits 3:1; bypass through 127
CMD0x7E0xB6 soft reset; 0xB0 FIFO flush
FIFO capacity512 bytesParse headers and service before overflow

Do not configure a data rate faster than the selected conversion can complete.

Compensation and engineering units

Use the individual sensor coefficients

Manufacturer-referenced values7 parameters

Scroll within the table to see all columns and rows.

ParameterValueConditions / notes
Trim storage21 bytes from 0x31–0x45T1–T3 and P1–P11; preserve signedness
Unsigned coefficientsT1, T2, P5, P6 are 16-bitOther coefficient widths/signs follow the manufacturer table
Temperature firstCompute the intermediate linearized temperaturePressure compensation depends on it
Pressure nextApply the calibrated polynomial to the raw pressureUse the Bosch BMP3 driver or the datasheet algorithm
Pascals to hectopascals101325 Pa / 100 = 1013.25 hPaIllustrative compensated value, not a raw register example
AltitudeRequires a reference pressure and atmosphere modelWeather changes can mimic an altitude change
ConsistencyRead all six data bytes in one burstPrevents mixing bytes from different conversions

BMP280 and BMP388 calibration layouts and compensation algorithms are different.

Package and layout

Bosch Figure 26 land dimensions

Manufacturer-referenced values6 parameters

Scroll within the table to see all columns and rows.

ParameterValueConditions / notes
Metal-lid LGA2.0 × 2.0 × 0.75 mm typical0.8 mm maximum height
Contacts10; no center exposed padTop-view map is not the bottom-view drawing
Side lands0.275 × 0.250 mm0.5 mm pitch; 1.525 mm between row centers
Top and bottom lands0.250 × 0.275 mm0.5 mm between contact centers
Air portKeep open and uncontaminatedNo conformal coating over the sensing hole
LifecycleReference for BMP388 designsBosch recommends BMP390 for new designs

The original KiCad land pattern needs the normal manufacturing review for the target PCB process.

Read each value with its conditions

Typical values describe the stated test conditions. Absolute maximum ratings are stress limits, not operating targets.

Bosch Sensortec · BST-BMP388-DS001-07 · November 2020 · Revision 1.7
Official PDF datasheet

Component view