DHT11 Reference Tables
Search the DHT11 pin reference and manufacturer-referenced specification tables.
Pin reference
Signal names, electrical functions and connection guidance
Scroll within the table to see all columns and rows.
| Pin | Signal | Type | Function & connection |
|---|---|---|---|
| VCC | Supply | Positive supply input.Connection guidanceConnect to 3.3–5.5 V. The example uses 5 V and a local 100 nF bypass. Use a controller whose input tolerates the chosen data pullup voltage. | |
| SDA | Bidirectional data | Single data line carries the start pulse, response and 40-bit frame.Connection guidanceUse an open-drain or switchable input/output GPIO and an external pullup. This is the DHT pulse-width protocol, not I²C or Dallas 1-Wire. | |
| NC | No connection | Unused physical lead.Connection guidanceLeave unconnected. | |
| GND | Ground | Supply and data reference.Connection guidanceConnect to the controller ground. |
No pins match these filters. Try another signal name or reset the filters.
Supply and sampling
December 2022 manufacturer revision
Scroll within the table to see all columns and rows.
| Parameter | Value | Conditions / notes |
|---|---|---|
| Supply | 3.3–5.5 V | 5 V nominal in the manufacturer table |
| Startup wait | At least 2 s | Do not request a reading during initialization |
| Sampling interval | At least 2 s | Also applies when requesting a fresh second result |
| Sleep / measurement current | 60 µA / 1000 µA typical | VCC=5 V and 25°C |
| Typical pullup | 4.7 kΩ | Short local connection; adjust for line capacitance |
| Example bypass | 100 nF | Local VCC-to-GND decoupling |
| 3.3 V wiring advice | Keep cable within 1 m | Manufacturer recommendation to limit supply drop |
No specifications match. Try a parameter name or a unit.
The wire carries timed pulses, not an addressable multidrop protocol.
Temperature and humidity
Reference conditions and range qualifications
Scroll within the table to see all columns and rows.
| Parameter | Value | Conditions / notes |
|---|---|---|
| Humidity measurement envelope | 5–95%RH | Normal recommended scope is narrower and temperature-dependent |
| Normal humidity scope | 8–85%RH headline | Follow the working-conditions curve, especially near temperature extremes |
| Humidity error | ±5%RH typical | 25°C, VCC=5 V, non-condensing; excludes hysteresis/nonlinearity |
| Humidity repeatability / hysteresis | ±1%RH / ±0.3%RH typical | Reference conditions |
| Humidity response | Less than 6 s typical | 63% response at 25°C and 1 m/s airflow |
| Temperature range | −20°C to +60°C | Selected manual revision |
| Temperature error / repeatability | ±2°C / ±1°C typical | Not a claim of decimal-byte accuracy |
| Temperature response | 5–30 s | Depends on airflow and thermal coupling |
| Long-term drift | Less than 0.5%RH/year and 0.5°C/year typical | Reference conditions |
No specifications match. Try a parameter name or a unit.
Keep the sensor away from heat sources and contaminants; avoid condensation.
Single-wire timing
Use the min/max windows from this revision
Scroll within the table to see all columns and rows.
| Parameter | Value | Conditions / notes |
|---|---|---|
| Host start LOW | 18–30 ms | 20 ms typical |
| Host release interval | 10–35 µs | 13 µs typical |
| Sensor response LOW | 78–88 µs | 83 µs typical |
| Sensor response HIGH | 80–92 µs | 87 µs typical |
| Each bit LOW | 50–58 µs | 54 µs typical |
| Zero-bit HIGH | 23–27 µs | 24 µs typical |
| One-bit HIGH | 68–74 µs | 71 µs typical |
| Release after frame | 52–56 µs LOW | Then sensor releases SDA |
No specifications match. Try a parameter name or a unit.
Use bounded receive timeouts. Interrupt latency must not obscure the short pulse windows.
Five-byte measurement frame
40 bits · MSB first · DHT11 format
Scroll within the table to see all columns and rows.
| Parameter | Value | Conditions / notes |
|---|---|---|
| Byte 0 | Humidity integer | 52 decimal for 52.x%RH |
| Byte 1 | Humidity decimal portion | Follow this device revision; do not combine as an AM2302 16-bit value |
| Byte 2 | Temperature integer magnitude | 25 decimal for +25.x°C |
| Byte 3 | Sign and temperature decimal portion | Bit 7 selects negative; lower bits carry fractional data |
| Byte 4 | Sum of bytes 0–3 modulo 256 | Reject the frame if the received check byte differs |
| Example frame | 34 00 19 00 4D hex | 52%RH, +25°C; 0x34+0x00+0x19+0x00=0x4D |
| Prior measurement | Returned before a new conversion | For a fresh second result, keep the ≥2 s interval |
No specifications match. Try a parameter name or a unit.
Do not interpret DHT11 bytes with the AM2302 sign/magnitude 16-bit format.
Four leads, three connections
Front vent face toward you; leads down
Scroll within the table to see all columns and rows.
| Parameter | Value | Conditions / notes |
|---|---|---|
| Pin 1 · VCC | 5 V in this example | Sensor and controller use the same rail |
| Pin 2 · SDA | Controller bidirectional GPIO | 4.7 kΩ pullup to 5 V |
| Pin 3 · NC | Leave open | Do not ground this contact |
| Pin 4 · GND | Common controller return | Keep motor currents away from the signal ground |
| Controller port | Open drain / switchable input | Release the bus after the start pulse |
| 3.3 V MCU with 5 V sensor | Check input tolerance or level-shift | Do not assume its input is 5 V tolerant |
| Communication topology | One sensor per GPIO | No device address is present in the DHT frame |
No specifications match. Try a parameter name or a unit.
The bare sensor and a breakout board can have different connector orders.
Enclosure and installation
Original package and footprint views
Scroll within the table to see all columns and rows.
| Parameter | Value | Conditions / notes |
|---|---|---|
| Blue enclosure | 12.50×16.00×6.00 mm | Manufacturer drawing; nominal dimensions |
| Lead pitch | 2.54 mm | Four straight leads; 7.62 mm outer span |
| Exposed lead length | 7.20±0.50 mm | Drawing value |
| Lead section | 0.50×0.30 mm nominal | Check finished-hole allowance |
| Original footprint | 1.80 mm pads; 1.00 mm drills | Upright SIP-4; review assembly clearances |
| Air openings | Keep unobstructed | Enclosures and absorbent materials can slow response |
| SMD package | Not shown for this sensor | Do not substitute a generic IC package |
No specifications match. Try a parameter name or a unit.
The 3D view is an original nominal enclosure illustration; the KiCad file is a reviewed authored footprint.
No matching rowsTry a pin name, parameter, unit or test condition, or reset the filters.