LIS3DH Reference Tables
Search the LIS3DH pin reference and manufacturer-referenced specification tables.
Pin reference
Signal names, electrical functions and connection guidance
Scroll within the table to see all columns and rows.
| Pin | Signal | Type | Function & connection |
|---|---|---|---|
| Vdd_IO | Supply | Interface power supply.Connection guidanceConnect to the logic rail; 3.3 V is used in the example. Operating 1.71 V to Vdd + 0.1 V. | |
| NC | No connection | Not connected internally.Connection guidanceLeave open. | |
| NC | No connection | Not connected internally.Connection guidanceLeave open. | |
| SCL / SPC | Input | I²C clock or SPI serial clock.Connection guidanceFor I²C, connect to host SCL with a pullup to Vdd_IO. | |
| GND | Return | First ground contact.Connection guidanceConnect to common ground with pins 10 and 12. | |
| SDA / SDI / SDO | Bidirectional | I²C data, SPI data input or three-wire SPI data output.Connection guidanceConnect to host SDA with a Vdd_IO pullup for I²C. | |
| SDO / SA0 | Output / address | SPI data output or I²C address bit.Connection guidanceGround selects seven-bit address 0x18; Vdd_IO selects 0x19. An internal pullup is present; explicitly define the chosen address. | |
| CS | Input | Active-low SPI chip select and interface selection.Connection guidanceTie to Vdd_IO for I²C; drive as chip select for SPI. | |
| INT2 | Output | Second programmable inertial interrupt.Connection guidanceConnect to a host input when used; otherwise leave open. | |
| RES | Reserved ground | Reserved contact with a required ground connection.Connection guidanceConnect to GND. Do not leave this reserved pin floating. | |
| INT1 | Output | First programmable interrupt, including data-ready routing.Connection guidanceConnect to a host interrupt input when needed. | |
| GND | Return | Second ground contact.Connection guidanceConnect to common ground. | |
| ADC3 | Input | Third auxiliary ADC channel. Temperature sensing can replace this input internally.Connection guidanceLeave open when unused, as permitted by the manufacturer. ADC input range is 0.8–1.6 V; it is not a full-supply-range ADC. | |
| Vdd | Supply | Sensor-core power supply.Connection guidanceUse 1.71–3.6 V; place 100 nF ceramic and 10 µF bulk bypass nearby. | |
| ADC2 | Input | Second auxiliary ADC channel.Connection guidanceLeave open when unused. External ADC input range is 0.8–1.6 V. | |
| ADC1 | Input | First auxiliary ADC channel.Connection guidanceLeave open when unused. External ADC input range is 0.8–1.6 V. |
No pins match these filters. Try another signal name or reset the filters.
Power and interface
Typical values use manufacturer conditions
Scroll within the table to see all columns and rows.
| Parameter | Value | Conditions / notes |
|---|---|---|
| Vdd | 1.71–3.6 V | Core supply |
| Vdd_IO | 1.71 V to Vdd + 0.1 V | Bus pullups use this rail |
| Normal mode at 50 Hz | 11 µA typical | Vdd 2.5 V, 25°C |
| Low-power mode at 50 Hz | 6 µA typical | 8-bit mode |
| Power-down current | 0.5 µA typical | Measurement chain inactive |
| Digital thresholds | HIGH ≥0.8×Vdd_IO; LOW ≤0.2×Vdd_IO | Match host levels |
| I²C / SPI maximum clock | 400 kHz / 10 MHz | Meet bus timing and loading requirements |
| Operational temperature | −40 to +85°C | Do not confuse with compensated accuracy limits |
No specifications match. Try a parameter name or a unit.
The example uses one 3.3 V rail for core and interface.
Resolution and scaling
Values after arithmetic right-shifting the signed word
Scroll within the table to see all columns and rows.
| Parameter | Value | Conditions / notes |
|---|---|---|
| High-resolution mode | 12 bits; shift right 4 | LPen=0, HR=1 |
| Normal mode | 10 bits; shift right 6 | LPen=0, HR=0 |
| Low-power mode | 8 bits; shift right 8 | LPen=1, HR=0 |
| LPen=1 and HR=1 | Not allowed | Do not enable both |
| Sensitivity at ±2 g | HR: 1; normal: 4; low-power: 16 mg/digit | FS=00 |
| Sensitivity at ±4 g | HR: 2; normal: 8; low-power: 32 mg/digit | FS=01 |
| Sensitivity at ±8 g | HR: 4; normal: 16; low-power: 64 mg/digit | FS=10 |
| Sensitivity at ±16 g | HR: 12; normal: 48; low-power: 192 mg/digit | FS=11; do not infer the sensitivity from nominal range alone |
No specifications match. Try a parameter name or a unit.
Typical zero-g offset at ±2 g is ±40 mg; calibration and mounting matter.
A 100 Hz high-resolution setup
I²C address 0x18 with SA0 grounded
Scroll within the table to see all columns and rows.
| Parameter | Value | Conditions / notes |
|---|---|---|
| WHO_AM_I | 0x0F → 0x33 | Identity byte, independent of the selected bus address |
| CTRL_REG4 | 0x23 → 0x88 | BDU enabled, ±2 g, high-resolution, little-endian, four-wire SPI setting |
| CTRL_REG1 | 0x20 → 0x57 | 100 Hz, all axes enabled, LPen=0 |
| Startup settling | 7 / ODR for high-resolution mode | About 70 ms at 100 Hz |
| STATUS_REG | 0x27; ZYXDA bit 3 | New XYZ data available |
| Acceleration burst | Sub-address 0xA8; receive 6 bytes | 0x28 with auto-increment bit 7 set |
| Byte order | XL, XH, YL, YH, ZL, ZH | Little-endian when BLE=0 |
| Example conversion | 0x3E80 → 16000 → 1000 counts → 1 g | Signed word >>4; 1 mg/digit at ±2 g |
| Power-down | ODR bits = 0000 | Configure through CTRL_REG1 |
No specifications match. Try a parameter name or a unit.
Read the complete pair of bytes per axis when BDU is enabled.
Filters, interrupts and FIFO
Choose functions for the measurement task
Scroll within the table to see all columns and rows.
| Parameter | Value | Conditions / notes |
|---|---|---|
| Normal / low-power bandwidth | ODR / 2 | Manufacturer mode table |
| High-resolution bandwidth | ODR / 9 | Lower bandwidth than normal mode at the same ODR |
| Common output rates | 1, 10, 25, 50, 100, 200, 400 Hz | Higher-rate options depend on resolution mode |
| High-resolution / normal maximum | 1.344 kHz | Low-power mode has separate high-rate settings |
| FIFO depth | 32 XYZ samples | Bypass, FIFO, stream and stream-to-FIFO modes |
| FIFO enable / configuration | CTRL_REG5 0x24 bit 6; FIFO_CTRL 0x2E | Check FIFO_SRC 0x2F for level and overrun |
| INT1 data-ready route | CTRL_REG3 0x22 bit 4 | Route ZYX data-ready when using the interrupt |
| Motion / free-fall detection | Programmable axis thresholds and duration | Configure event source, polarity and latching |
| Gravity | Included in static acceleration | A high-pass filter removes DC and changes tilt interpretation |
No specifications match. Try a parameter name or a unit.
These are acceleration-based features; LIS3DH is not a gyroscope.
Auxiliary ADC and temperature
Keep these channels distinct from XYZ
Scroll within the table to see all columns and rows.
| Parameter | Value | Conditions / notes |
|---|---|---|
| External ADC inputs | ADC1, ADC2 and ADC3 | Pins 16, 15 and 13 |
| External ADC input range | 0.8–1.6 V | 1.2 V center ±0.4 V; not 0–Vdd |
| ADC enable | TEMP_CFG 0x1F bit 7; BDU must be set | Output rate follows CTRL_REG1 ODR |
| Auxiliary ADC resolution | 10 bits normally; 8 bits in low-power | Signed, left-aligned data |
| Temperature select | TEMP_CFG bit 6 with ADC enabled | Temperature replaces auxiliary channel 3 |
| Temperature sensitivity | 1 digit/°C at 8-bit representation | An offset/reference calibration is needed for absolute temperature |
| Temperature supply condition | Vdd 2.0–3.6 V | Different from the accelerometer’s full supply range |
| Unused ADC contacts | May be open or tied to Vdd/GND | Keep the ADC disabled when not required |
No specifications match. Try a parameter name or a unit.
Do not label a raw temperature code as a calibrated ambient reading.
Wiring and LGA assembly
Top-view numbering, not the bottom-view drawing
Scroll within the table to see all columns and rows.
| Parameter | Value | Conditions / notes |
|---|---|---|
| I²C mode | CS8 → Vdd_IO | SCL4 and SDA6 need external pullups |
| Address selection | SA0 low → 0x18; high → 0x19 | SA0 has an internal pullup |
| Grounds | GND5, RES10 and GND12 | Reserved contact 10 must be grounded |
| Vdd14 bypass | 100 nF ceramic + 10 µF bulk | Place close to the sensor supply |
| Body / contact pitch | 3 × 3 mm; 0.50 mm | Five side contacts, three top/bottom contacts |
| Original copper lands | 0.45 × 0.35 mm | TN0018 adds 0.10 mm to each package-pad dimension |
| Pin-one indicator | Leave unconnected and unsoldered | It is not a seventeenth electrical pin |
| MEMS keepout | No top-layer structures beneath the sensor | Follow ST routing, mask and stencil guidance |
No specifications match. Try a parameter name or a unit.
Assembly reference: https://www.st.com/resource/en/technical_note/tn0018-handling-mounting-and-soldering-guidelines-for-mems-devices-stmicroelectronics.pdf
No matching rowsTry a pin name, parameter, unit or test condition, or reset the filters.