LIS3DH Specifications
Review LIS3DH electrical specifications, operating conditions and package details.
Key specifications
A capacitive MEMS structure senses three-axis acceleration. Conversion, filtering and configurable event logic make samples and interrupts available through the bus. Auxiliary ADC inputs and a temperature channel are separate from the motion axes.
Package details
LIS3DH · LGA-16
| Property | Details |
|---|---|
| Manufacturer | STMicroelectronics |
| Part number | LIS3DH |
| Package | LGA-16 |
| Connections | 16 pins |
| Mounting | SMD |
| Lead pitch | 0.50 mm |
| Package code | LGA |
| Thermal reference | −40°C to +85°C |
Power and interface
Typical values use manufacturer conditions
Scroll sideways to see all columns.
| Parameter | Value | Conditions / notes |
|---|---|---|
| Vdd | 1.71–3.6 V | Core supply |
| Vdd_IO | 1.71 V to Vdd + 0.1 V | Bus pullups use this rail |
| Normal mode at 50 Hz | 11 µA typical | Vdd 2.5 V, 25°C |
| Low-power mode at 50 Hz | 6 µA typical | 8-bit mode |
| Power-down current | 0.5 µA typical | Measurement chain inactive |
| Digital thresholds | HIGH ≥0.8×Vdd_IO; LOW ≤0.2×Vdd_IO | Match host levels |
| I²C / SPI maximum clock | 400 kHz / 10 MHz | Meet bus timing and loading requirements |
| Operational temperature | −40 to +85°C | Do not confuse with compensated accuracy limits |
No specifications match. Try a parameter name or a unit.
The example uses one 3.3 V rail for core and interface.
Resolution and scaling
Values after arithmetic right-shifting the signed word
Scroll sideways to see all columns.
| Parameter | Value | Conditions / notes |
|---|---|---|
| High-resolution mode | 12 bits; shift right 4 | LPen=0, HR=1 |
| Normal mode | 10 bits; shift right 6 | LPen=0, HR=0 |
| Low-power mode | 8 bits; shift right 8 | LPen=1, HR=0 |
| LPen=1 and HR=1 | Not allowed | Do not enable both |
| Sensitivity at ±2 g | HR: 1; normal: 4; low-power: 16 mg/digit | FS=00 |
| Sensitivity at ±4 g | HR: 2; normal: 8; low-power: 32 mg/digit | FS=01 |
| Sensitivity at ±8 g | HR: 4; normal: 16; low-power: 64 mg/digit | FS=10 |
| Sensitivity at ±16 g | HR: 12; normal: 48; low-power: 192 mg/digit | FS=11; do not infer the sensitivity from nominal range alone |
No specifications match. Try a parameter name or a unit.
Typical zero-g offset at ±2 g is ±40 mg; calibration and mounting matter.
A 100 Hz high-resolution setup
I²C address 0x18 with SA0 grounded
Scroll sideways to see all columns.
| Parameter | Value | Conditions / notes |
|---|---|---|
| WHO_AM_I | 0x0F → 0x33 | Identity byte, independent of the selected bus address |
| CTRL_REG4 | 0x23 → 0x88 | BDU enabled, ±2 g, high-resolution, little-endian, four-wire SPI setting |
| CTRL_REG1 | 0x20 → 0x57 | 100 Hz, all axes enabled, LPen=0 |
| Startup settling | 7 / ODR for high-resolution mode | About 70 ms at 100 Hz |
| STATUS_REG | 0x27; ZYXDA bit 3 | New XYZ data available |
| Acceleration burst | Sub-address 0xA8; receive 6 bytes | 0x28 with auto-increment bit 7 set |
| Byte order | XL, XH, YL, YH, ZL, ZH | Little-endian when BLE=0 |
| Example conversion | 0x3E80 → 16000 → 1000 counts → 1 g | Signed word >>4; 1 mg/digit at ±2 g |
| Power-down | ODR bits = 0000 | Configure through CTRL_REG1 |
No specifications match. Try a parameter name or a unit.
Read the complete pair of bytes per axis when BDU is enabled.
Filters, interrupts and FIFO
Choose functions for the measurement task
Scroll sideways to see all columns.
| Parameter | Value | Conditions / notes |
|---|---|---|
| Normal / low-power bandwidth | ODR / 2 | Manufacturer mode table |
| High-resolution bandwidth | ODR / 9 | Lower bandwidth than normal mode at the same ODR |
| Common output rates | 1, 10, 25, 50, 100, 200, 400 Hz | Higher-rate options depend on resolution mode |
| High-resolution / normal maximum | 1.344 kHz | Low-power mode has separate high-rate settings |
| FIFO depth | 32 XYZ samples | Bypass, FIFO, stream and stream-to-FIFO modes |
| FIFO enable / configuration | CTRL_REG5 0x24 bit 6; FIFO_CTRL 0x2E | Check FIFO_SRC 0x2F for level and overrun |
| INT1 data-ready route | CTRL_REG3 0x22 bit 4 | Route ZYX data-ready when using the interrupt |
| Motion / free-fall detection | Programmable axis thresholds and duration | Configure event source, polarity and latching |
| Gravity | Included in static acceleration | A high-pass filter removes DC and changes tilt interpretation |
No specifications match. Try a parameter name or a unit.
These are acceleration-based features; LIS3DH is not a gyroscope.
Auxiliary ADC and temperature
Keep these channels distinct from XYZ
Scroll sideways to see all columns.
| Parameter | Value | Conditions / notes |
|---|---|---|
| External ADC inputs | ADC1, ADC2 and ADC3 | Pins 16, 15 and 13 |
| External ADC input range | 0.8–1.6 V | 1.2 V center ±0.4 V; not 0–Vdd |
| ADC enable | TEMP_CFG 0x1F bit 7; BDU must be set | Output rate follows CTRL_REG1 ODR |
| Auxiliary ADC resolution | 10 bits normally; 8 bits in low-power | Signed, left-aligned data |
| Temperature select | TEMP_CFG bit 6 with ADC enabled | Temperature replaces auxiliary channel 3 |
| Temperature sensitivity | 1 digit/°C at 8-bit representation | An offset/reference calibration is needed for absolute temperature |
| Temperature supply condition | Vdd 2.0–3.6 V | Different from the accelerometer’s full supply range |
| Unused ADC contacts | May be open or tied to Vdd/GND | Keep the ADC disabled when not required |
No specifications match. Try a parameter name or a unit.
Do not label a raw temperature code as a calibrated ambient reading.
Wiring and LGA assembly
Top-view numbering, not the bottom-view drawing
Scroll sideways to see all columns.
| Parameter | Value | Conditions / notes |
|---|---|---|
| I²C mode | CS8 → Vdd_IO | SCL4 and SDA6 need external pullups |
| Address selection | SA0 low → 0x18; high → 0x19 | SA0 has an internal pullup |
| Grounds | GND5, RES10 and GND12 | Reserved contact 10 must be grounded |
| Vdd14 bypass | 100 nF ceramic + 10 µF bulk | Place close to the sensor supply |
| Body / contact pitch | 3 × 3 mm; 0.50 mm | Five side contacts, three top/bottom contacts |
| Original copper lands | 0.45 × 0.35 mm | TN0018 adds 0.10 mm to each package-pad dimension |
| Pin-one indicator | Leave unconnected and unsoldered | It is not a seventeenth electrical pin |
| MEMS keepout | No top-layer structures beneath the sensor | Follow ST routing, mask and stencil guidance |
No specifications match. Try a parameter name or a unit.
Assembly reference: https://www.st.com/resource/en/technical_note/tn0018-handling-mounting-and-soldering-guidelines-for-mems-devices-stmicroelectronics.pdf
Connections by function
Select a pin for its function, connection guidance and electrical notes.