ESP32-C6 DevKitC-1 Library for Proteus: JSN-SR04T, BTS7960 Pump

Hello friends, I hope you all are doing great. Today, I am going to share the ESP32-C6 DevKitC-1 Library for Proteus. The ESP32-C6 is Espressif's newest everyday chip: a RISC-V processor with Wi-Fi 6, Bluetooth LE and an 802.15.4 radio for Thread and Zigbee, all in one. The DevKitC-1 is Espressif's own board for it. With this library it runs your ESP32-C6 Arduino sketch in Proteus 8.5 and joins our virtual Wi-Fi network, with its RGB LED, its buttons and a serial monitor.

For the demo we put it on a roof: a water tank pump controller. A JSN-SR04T waterproof ultrasonic sensor on the tank's lid measures how far down the water is, a BTS7960 motor driver runs the pump with a soft start, the board's RGB LED shows the level in colour, and a phone and a laptop read the tank and switch the pump between AUTO, ON and OFF on the board's web page.

NOTICE: Proteus has no ESP32-C6 model, so our team has put a lot of effort into building this board ourselves: the DevKitC-1's pins, Wi-Fi and LEDs are all our own model, and your sketch compiles with our free TEP Boards for Proteus add-on. Your feedback is the fuel that keeps us going, so please tell us what you think in the comments below or in the ESP32-C6 DevKitC-1 board of our forum. And if our free libraries help you, you can buy us a coffee. So, let's get started with the ESP32-C6 DevKitC-1 Library for Proteus:

What is the ESP32-C6 DevKitC-1?

The ESP32-C6 came out in 2023 as Espressif's first chip with Wi-Fi 6 (802.11ax) on 2.4 GHz. It has a 160 MHz RISC-V core for your program and a second, 20 MHz low-power RISC-V core that can watch sensors while the main core sleeps, 512 KB of RAM, Bluetooth 5 LE and an IEEE 802.15.4 radio - the radio of Thread, Zigbee and Matter smart-home devices. The ESP32-C6-DevKitC-1 puts the ESP32-C6-WROOM-1 module (8 MB of flash, a PCB antenna) on a small board with two USB-C ports - one through a USB-to-UART bridge, one straight to the chip - the BOOT and RESET buttons, an addressable RGB LED on GPIO8 and two 16-pin headers.

Our ESP32-S3 DevKitC-1 Library for Proteus is the same Espressif board design with the dual-core S3; the ESP32-C3 SuperMini Library for Proteus is the tiny RISC-V board. Sketches move between them with only pin changes - the Arduino-ESP32 API is the same.

Why the ESP32-C6?

Pick the C6 for smart-home and battery projects: Wi-Fi 6's target wake time lets a sensor sleep between scheduled check-ins, the low-power core can poll a sensor without waking the main one, and the 802.15.4 radio makes the board a Thread or Zigbee device next to its Wi-Fi. For a simple Wi-Fi sketch it behaves like any ESP32: WiFi.begin, WebServer, HTTPClient and the same pin functions.

Features of the ESP32-C6 DevKitC-1 Library for Proteus

• The board as it looks: the black DevKitC-1 with its two USB-C ports, RST and BOOT, the LDO, the USB-to-UART bridge, the PWR LED, the RGB LED, the J5 jumper, the ESP32-C6-WROOM-1 module with its antenna and the 16 + 16 pins.
• Your sketch: a .hex for "ESP32-C6 DevKitC-1 (TEP Proteus)" with the C6's GPIO numbers - GPIO 0 to 13 and 15 to 23, analogRead 0 to 4095 on GPIO0 to 6, analogWrite and ledc PWM, attachInterrupt, pulseIn, Serial, Wire, SPI.
• The RGB LED: rgbLedWrite(RGB_BUILTIN, r, g, b) and neopixelWrite - the board shows the colour.
• Wi-Fi: WiFi.begin, WebServer, HTTPClient, mDNS and NTP on our virtual router TEP-WiFi; the board is 192.168.1.101 in the demo.
• The panel and the serial monitor: the board's panel (Wi-Fi, Pins, Test) and the built-in serial monitor with Monitor, Plotter and Board tabs - our TEP header, no Windows title bar.
• A complete package: about 3.5 MB with the board, the add-on, the JSN-SR04T, BTS7960, motor and monitor libraries and the demo, without the source code of the models.

The ESP32-C6 DevKitC-1 in Proteus

Search ESP32-C6 in Pick Devices; the device ESP32-C6 DEVKITC-1 is in TEPESP32C6.LIB (Microprocessor ICs, ESP32 Boards), with the prefix U. The board lies with the USB-C ports on the left and the module on the right. Click a USB-C port to open the serial monitor and the PANEL pad (or the module) to open the board's panel.

The Pins

Download ESP32-C6 DevKitC-1 Library for Proteus

Click the button below to download ESP32-C6-DevKitC-1-Library-for-Proteus-v1.0.zip (about 3.5 MB, without the source code of the models):

ESP32-C6 DevKitC-1 Library for Proteus V1.0

• README.txt: installation, the demo, the pins, the properties, troubleshooting and the limits.
• Proteus Library Files: TEPESP32C6.LIB and the demo's parts: TEPJSNSR04T.LIB, TEPBTS7960.LIB, TEPMOTOR775.LIB, TEPLAPTOP.LIB and TEPMOBILE.LIB.
• Proteus Model Files: TEPNET.DLL (the board, the laptop, the phone and the network) and the DLLs of the sensor, the driver and the motor.
• Arduino Code: the demo sketch and the TEP Boards for Proteus add-on 1.22.0.
• Proteus Simulation: the demo project, its HEX file and copies of the DLLs.

No Proteus yet? Read How to Download and Install Proteus 7 and 8. New to libraries? Follow How to Install a New Library in Proteus.

How to Install ESP32-C6 DevKitC-1 Library for Proteus

1. Close Proteus and extract the whole zip file, for example to your Desktop.
2. Copy the files from Proteus Library Files into the LIBRARY folder of Proteus.
3. Copy the DLLs from Proteus Model Files into the MODELS folder, replacing an older TEPNET.DLL.
4. Delete TEPESP32C6.IDX from the LIBRARY folder if it is there.
5. For your own sketches, copy Arduino Code\TEP Boards for Proteus\hardware into your Arduino sketchbook (Documents\Arduino) and restart the Arduino IDE; the board is ESP32-C6 DevKitC-1 (TEP Proteus).
6. Start Proteus, press P and search for ESP32-C6.

Demo: a Water Tank Pump Controller

Many homes keep a water tank on the roof, filled by a pump from a well or the street supply. Run the pump too long and the tank overflows; forget it and the taps run dry. A controller watches the level and does the job by itself. Ours uses a JSN-SR04T - the waterproof cousin of the HC-SR04, with its sealed probe on a cable, made for exactly this kind of wet, closed space - and a BTS7960, a 43 A H-bridge that easily drives a 12 V pump motor.

Open ESP32-C6-DevKitC-1-Tank-Pump.pdsprj. U1 runs ESP32C6_Tank_Pump.hex. The parts come from our own libraries, each with its article: U2 from the JSN-SR04T Waterproof Ultrasonic Sensor Library for Proteus and DRV1 with the 775 motor M1 (our pump) from the BTS7960 Motor Driver Library for Proteus. Both are the Advance versions: each opens a pop-up window at Run. PC1 is the Laptop WiFi Monitor and MOB1 the Mobile WiFi Monitor.

In the demo the JSN-SR04T's 5V is on a label named VCC - Proteus' power rail - and the BTS7960's VCC on the board's 5V. On a real board the JSN-SR04T also runs on 5 V, so its ECHO pin needs a divider (for example 1k and 2k) down to the C6's 3.3 V.

How the JSN-SR04T Measures the Water

The sensor sends a short burst of 40 kHz sound when TRIG gets a pulse, then holds ECHO HIGH until the echo comes back. Sound travels about 343 m/s, so each centimetre of distance adds about 58 microseconds to the round trip: the distance in centimetres is the ECHO time divided by 58. When nothing answers, the JSN-SR04T holds ECHO HIGH for about 36 ms - the sketch reads that as "no echo" and stops the pump, because it can no longer see the water. The sensor has a blind zone of about 20 cm, so it sits a little above the highest water level.

void measure() {
  digitalWrite(TRIG_PIN, HIGH);
  delayMicroseconds(20);
  digitalWrite(TRIG_PIN, LOW);
  unsigned long us = pulseIn(ECHO_PIN, HIGH, 40000UL);
  echoOk = us > 0 && us < 35000UL;                          // no echo: the JSN-SR04T holds ECHO HIGH about 36 ms
  if (!echoOk) return;
  distanceCm = us / 58;
  level = constrain((long)(EMPTY_CM - distanceCm) * 100 / (EMPTY_CM - FULL_CM), 0, 100);
}

From Distance to a Level

The tank is 2 m deep and the sensor is 25 cm above the full mark: 225 cm down means empty and 25 cm down means full. The sketch turns the distance into a percentage with a straight line between those two points:

const int EMPTY_CM = 225, FULL_CM = 25;                     // the sensor to the water: an empty / a full tank
const int START_PCT = 25, STOP_PCT = 90;                    // AUTO: the pump starts at 25 % and stops at 90 %

A Band, Not a Point

If the pump started below 50 % and stopped above 50 %, it would switch on and off every few seconds around that point - hard on the motor and the relay. So AUTO uses a band (hysteresis): the pump starts at 25 % and runs until 90 %. Between those two levels it keeps doing whatever it was doing. ON runs the pump until the tank is full, then returns to AUTO; OFF keeps it off whatever the level:

void control() {
  if (!echoOk) setPump(false, "no echo");
  else if (mode == 2) setPump(false, "mode OFF");
  else if (level >= STOP_PCT) { setPump(false, "tank full"); if (mode == 1) mode = 0; }
  else if (mode == 1) setPump(true, "mode ON");
  else if (level <= START_PCT) setPump(true, "tank low");
}

A Soft Start with the BTS7960

A pump that starts at full power with a long pipe behind it makes a bang - water hammer. The sketch ramps the PWM from 0 to full speed in about a second, ten steps of 10 %. The BTS7960 takes the PWM on RPWM and switches the 12 V supply to the motor; R_EN and L_EN stay HIGH and LPWM stays LOW, so the motor only turns one way:

void softStart() {                                          // 0 to full speed in about a second: no water hammer
  if (!pumpOn || duty >= 255 || millis() < nextRamp) return;
  nextRamp = millis() + 100;
  duty = min(255, duty + 25);
  analogWrite(PUMP_PWM, duty);
}

The RGB LED

The DevKitC-1's RGB LED is an addressable WS2812-type LED on GPIO8. In the Arduino-ESP32 core rgbLedWrite() sets its colour; the sketch uses it as a tank gauge you can read across the roof:

void showLevel() {                                          // the RGB LED: red LOW, amber, green above 60 %, purple no echo
  int c = !echoOk ? 3 : level <= START_PCT ? 0 : level < 60 ? 1 : 2;
  if (c == shown) return;
  shown = c;
  if (c == 0) rgbLedWrite(RGB_BUILTIN, 255, 0, 0);
  else if (c == 1) rgbLedWrite(RGB_BUILTIN, 255, 140, 0);
  else if (c == 2) rgbLedWrite(RGB_BUILTIN, 0, 255, 0);
  else rgbLedWrite(RGB_BUILTIN, 160, 0, 255);
}

Wi-Fi and the Page

The sketch joins the network and starts the ESP32 core's WebServer with three pages: / for the phone, /json for a program and /mode?m= for the AUTO, ON and OFF links:

  server.on("/", handleRoot);
  server.on("/json", handleJson);
  server.on("/mode", handleMode);

The loop pings the tank five times a second, then ramps the pump, logs, reads the BOOT button, serves the page and reads the monitor:

void loop() {
  if (millis() >= nextPing) {                               // a ping every 200 ms (the module needs 50 ms between pings)
    nextPing = millis() + 200;
    measure();
    control();
    showLevel();
  }
  softStart();
  logStatus();
  readButtons();
  server.handleClient();
  readMonitor();
}

Run the Demo

Press Run. The serial monitor opens; the board joins TEP-WiFi and the first ping finds the water 200 cm down - about 12 %, LOW. The pump starts:

ESP32-C6 Tank Pump - The Engineering Projects
Connecting to TEP-WiFi
Tank page: http://192.168.1.101/
Pump START (tank low) - tank at 14 %
Tank 14 % LOW (water 197 cm down)  pump ON 9 %  mode AUTO
Tank 13 % LOW (water 199 cm down)  pump ON 100 %  mode AUTO

Open the Page

On the laptop click Browser and Go (the home page is http://192.168.1.101/json, the values for a program); on the phone the same with http://192.168.1.101/, the page with its links:

The Tank Fills

On the JSN-SR04T's pop-up click 100 cm and then +10: the water is 110 cm down, about 57 %. The level has left the LOW zone, but the pump keeps running - it stops only at 90 %. The RGB LED turns amber:

Full: the Pump Stops

Click 25 cm: 100 %, FULL. The sketch stops the pump, the RGB LED turns green and the BTS7960 lets the motor coast:

OFF and AUTO from the Phone

Tap OFF on the phone - say, to clean the tank. Then click 200 cm on the pop-up: the tank is LOW again, the RGB LED red, but the pump stays off. Tap AUTO and the pump starts at once:

The built-in serial monitor, in the look of our TEP Serial Monitor Advance for Proteus, logs every change and a status line every 2 s:

Tank 58 % OK (water 109 cm down)  pump ON 100 %  mode AUTO
Tank 57 % OK (water 110 cm down)  pump ON 100 %  mode AUTO
Pump STOP (tank full) - tank at 100 %
Tank 100 % FULL (water 24 cm down)  pump OFF  mode AUTO
Mode OFF (from the web page)
Tank 100 % FULL (water 24 cm down)  pump OFF  mode OFF
Tank 13 % LOW (water 199 cm down)  pump OFF  mode OFF
Mode AUTO (from the web page)
Pump START (tank low) - tank at 13 %
Tank 13 % LOW (water 199 cm down)  pump ON 100 %  mode AUTO

Try It Yourself

• Click NONE on the JSN-SR04T's pop-up: no echo - the pump stops and the RGB LED turns purple.
• Press the board's BOOT button: the mode switches between AUTO and OFF.
• Tap ON with the tank half full: the pump runs until FULL, then the mode returns to AUTO.
• Type STATUS, AUTO, ON or OFF in the monitor.

Ideas to Extend the Tank Controller

• Add a dry-run guard: if the level does not rise within a minute of starting, stop the pump and raise an alarm.
• Log the level every hour with NTP time and draw the day's water use on the page.
• Use the pump's current from the BTS7960's R_IS pin to spot a blocked or dry pump.
• Send the level to a home server with HTTPClient, or (on a real C6) as a Thread or Zigbee sensor.

Your Own Sketches

Write the sketch in the Arduino IDE with the board ESP32-C6 DevKitC-1 (TEP Proteus), use Sketch > Export Compiled Binary and set the board's PROGRAM property to the .hex. The same sketch compiles for a real ESP32-C6-DevKitC-1 with Espressif's "esp32" package 3.x - select "ESP32C6 Dev Module" there and upload.

Things to Know Before Using a Real ESP32-C6 DevKitC-1

• 3.3 V logic: the C6's pins are not 5 V tolerant - divide the JSN-SR04T's ECHO down to 3.3 V.
• Two USB-C ports: the UART port goes through the bridge; the USB port is the C6's own USB (GPIO12 / 13). With the USB port, enable "USB CDC On Boot" in the IDE to see Serial there.
• The pump's supply: give the BTS7960 its own 12 V supply and join the grounds; never feed the motor from the board.
• The JSN-SR04T in the tank: keep the probe clear of the inlet pipe and the walls - the sound cone is wide - and above the overflow level.
• The J5 jumper: leave it on; it is there to measure the module's current.

Properties of the ESP32-C6 DevKitC-1

Troubleshooting

• The tank shows NO ECHO: TRIG on GPIO10, ECHO on GPIO11; the sensor's 5V on the power rail.
• The pump does not turn: RPWM on GPIO3, R_EN and L_EN on GPIO2, LPWM on GND, B+ on +12V.
• The board stays off the network: the sketch's SSID and password must match WIFISSID and WIFIPASS.
• A number goes wrong above 32767: int is 16 bits in the simulation - use long.
• The page shows old values: use REFRESH; the monitors do not reload by themselves.

Limitations of the Simulation

• Your sketch gets 8 KB of RAM in the simulation and runs slower than on the C6's 160 MHz RISC-V core with 512 KB.
• Wi-Fi 6 features, Bluetooth LE, Thread / Zigbee, the low-power core, the native USB and Serial1 are not modelled.
• The router, the addresses and the windows are TEP additions.
• ESP32-C6 and ESP32-C6-DevKitC-1 are names of Espressif Systems; this library is not made or endorsed by Espressif or by Labcenter.
• Tested in Proteus 8.5 in October 2026 (the demo as shipped, about 44 s of simulation). Proteus 7 is not supported.

So, that was all about the ESP32-C6 DevKitC-1 Library for Proteus. I hope it helps you build and test your ESP32-C6 projects before you touch the hardware - the sensor, the motor driver, the RGB LED and the web page in one simulation. If you have any questions, ask in the comments and I will help you out. Till the next tutorial, take care and have fun!