Sir i am not getting library folder in labcenter electronics. Please help me with this
Sir after downloading pir sensor library i got one .rar file only and also m nt getting library folder in labcentre electrnoics
I am doing one AVR based project where i need this sensor. Plz help me. Rply ASAP.
Hi,
Yeah unrar this rar file and you will get the library files and then follow the instructions in tutorial. The path of library folder is mentioned above in Note form and also make a search in your Labcenter folder for Libraries and you will get the folder. Its not that difficult.
Thanks.
Sir I copied that .rar file to library folder of proteus software. But still m not getting that sensor in proteus
Plz help
download a software of .rar file opener.....then install that software.......then by using the software open the rar file.............then whatever file you got copied to library folder of labcenter
Most PIR sensors have 2-3 triggering modes selectable via a jumper or solder bridge - maybe it would be nice to emulate that behavior by adding 2-3 pins to simulate the jumper / modes.
Trigger modes / retriggering explained here:
https://learn.adafruit.com/pir-passive-infrared-proximity-motion-sensor/testing-a-pir
Also, PIR sensor modules might have 1 pot for adjusting the cooldown period, i.e. how much time the sensor outputs a "triggered" signal (usually HIGH) before switching over (to usually LOW) - assuming no motion was detected during this period. That would also be nice to have as functionality, as currently it looks to me that once triggered it never goes back to LOW.
Other than that, good job.
In Proteus, designing of active models is quite difficult, but I will consider your suggestion and will try to add the knob in it. Thanks for the appreciation. (Y)
Hey, nice work and explanation about the PIR sensor. I have a problem with the virtual terminal, I can't visualize the motions with the serial port, I have made the same things that you suggest, the only difference is that I'm working on an arduino mega1280. May you help me?
On the virtual terminal on proteus I only see weird simbols when I change the logic state to 1.
Its a digital sensor, it wont work on Serial Protocol. You must be doing something wrong.
sir,
i want the blood pressure sensor in proteus
but i couldn't find the library of BMP i
please help me
please let me know if u could suggest any link
contact me here sir
02032013023.cst@rub.edu.bt
Add me on Skype and we will discuss it in detail. MY Skype id is theenggprojects.
Thanks.
Sir do you have a library for gyroscopes and flex sensors?
could you please explain the use of calibration time,lowin,pause,takelowtime?
Do you have a library for alarms (Specifically panic switches)?
hello sir can i know the name of the component that is connected to the test pin of pir sensor?
Its a Logic State, search it in Proteus components and you will find it.
hello pır sensor what i make the circuit always gives an error what i have to do
Unable to open HEX file '..\..\..\..\Users\zain\AppData\Local\Temp\build2551671029259847980.tmp/PIRTest.cpp.hex'. [PIR1]
the last time you did it again gives the same error
pırsensortep.hex
what should I do
giving error when running
go to c drive. turn on the display of hidden folder.Then, You will find ProgramData folder. go to "labcenter"
, then "proteas..." and then "Library"
Sir, thank you very much. It is the key of project. If you possible just send a PH sensor library for proteus.
send a ph sensor library like pir sensor library?
how to obtain pcb package for PIR sensor??
hello sir, where can i find solar panel library for proteus software
Hi,
It's not available yet and we are working on it, will be available soon. :))
Thanks.
Sir is here a magnetic reed switch library ?
Hi,
Yeah we have posted it recently. You can download it from this link: https://www.theengineeringprojects.com/2018/05/magnetic-reed-switch-library-for-proteus.html
Thanks.
Thanks so much for the description ,
virtual terminal won't pop up most times on my Proteus , is there remedy to the problem.?.
Hi,
Right click it and then you need to click on Virtual Terminal. It will be at the end and will only appear in running mode.
Thanks.
hello
i keep getting the error Program file is too big for the microcontroller: flash size = 32768, load address = 65550, number of bytes = 2.
do you know what's going wrong?
Hi,
Delete the Library files and download them again and place in the Library Folder. Now before running your simulation, don't forget to add the Hex file of PIR Sensor in its Properties section. I think it will solve the issue.
Thanks.
hy brother .....i faced the problem during my stimulation of that PIR where i searched logic button in my proteus so there was no match contents of it.....unfortunately i got logic generator but it didn't work....so,what can i do?
Hi,
Make a search for LogicState and you will get this button. Let me know if you still got any issues.
Thanks.
can you please upload GP2Y1010AU0F library for proteus
Is it possible to use this PIR sensor without arduino??
please send or upload weight sensor or load sensor for proteus liberary
hello. why i cannot download this library? only appear a coding at download button. please help me.
Hi David, thank you for sharing.
PIR is not working with my Proteus 8.15.
Several warning messages (more than 7000) like "[PIC18 EXEC] PC=0x0004. Attempt to execute illegal opcode (loaded from PC=0002). Instruction executes as a NOP. [PIR1] @0.000003000s".
I've followed all steps you showed.
Is there anything more that I need to do?
Inot even working running PIR alone.