Hello friends, i hope you all are fine and enjoying. Today i am going to share a new tutorial which is Interfacing Arduino with HC05 Bluetooth module. First of all lets have a little introduction about HC-05 Bluetooth module. HC-05 is a bluetooth module, which was designed for wireless data communication. This little module is capable of both sending and receiving data but it performs only one thing at a time, which means at a particular time it can only send or receive data but can't do the both tasks.
In order to send or to receive data, you have to make one module as a master and the other module as a slave. If both the modules are acting as master then, data will not transmit and if both the modules are acting as a slave then, again data will ...
Hello friends, I hope you all are doing great. In today's tutorial, I will show you how to perform Simplest Half Wave Rectification in Proteus. In this tutorial, we will design a simple Proteus simulation, where we will use a diode for half-wave rectification.
Before designing the Proteus simulation, we will first have a theoretical overview of Half Wave Rectification as it's always the best approach to read theory before practical (Proteus Simulation). So, let's get started:
What is Rectification ???
Rectification is an electrical process, used to convert Alternating(AC) Voltage into Direct(DC) Voltage using a circuit called rectifier.
The Rectification process is always carried out using diodes, as we know diodes allow the current to flow in one direction only, thus t ...
Hi Guys! Hope you're well today. Glad to have you here. In this post today I'll detail why EV pickup trucks will spearhead the switch to electric motors.
In 2019, approximately 63 percent of Americans looking to buy a car were interested in buying an EV, according to Consumer Reports. The stage is set for major EV manufacturers to contend over the market. Of all body styles, pickup trucks seem to be of particular interest to them. General Motors, Tesla, and Ford are doubling down their efforts in EV pickup design. This is all so that models like the Hummer EV and the Cyber truck can release within the next few years.
Trucks are favored for their towing power, traversal abilities, and relatively low need for maintenance. Those are perfect attribu ...
Hi Friends! Hope you’re well today. I welcome you on board. In this post today, I’ll walk you through the key benefits of data visualization.
Data visualization is something that used to be a competitive advantage, but now it is becoming a necessity to survive.
I have outlined some of the key benefits of data visualization and I will explain each point very briefly. If you take one thing away from this post it should be that data visualization is important and you should be implanting data visualization techniques into your business or organization.
Reducing Errors
Keeping track of your data will let you tell a story about your customers and your business. One negative part of the story is that data visualization will let you identify the prob ...
Lighters are popular for the cigar smokers but not only have the smokers used the lighters but also for the people who are interested in camping, picnicking and any other activities in the outside the windy environments. Usually, cigar smokers prefer butane torch lighters during the smoke.
A torch lighter is a portable thing that is used for instant flame or fire. It is used for many activities like outside cooking, lightening in the dark area, fishing, and many many activities. Butane torch lighter in an instrument that is worked by utilizing butane creates hot flames.
If you can’t buy a good torch lighter, it can make you in trouble in a serious condition. Suppose you are when you need instant fire and you have a lighter and unfortunately your ...
Hello friends, I hope you all are having fun. In today's tutorial, we will have a look at Series Clippers & their types in detail, we will also implement the simulations of Series Clippers in Proteus software. In the next article, we will discuss the next two types of Clippers i.e. Shunt Clippers & Dual Clippers. Today, We are going to learn:
What is a Clipper?
What are the types of Clippers?
Series Clippers Simulations in Proteus.
So, let's get started:
What is a Clipper???
Clipper (also known as Limiter) is an electronic circuit, which clips or limits the amplitude(positive, negative or both) of an AC source wave.
Diodes are normally used for designing Clippers and such circuits are normally referred as Diode Clipping Circuits (Diode Limiting Circuits).
...
Hello everyone! I hope you all will be absolutely fine and having fun. In the tutorial Interfacing Temperature & Humidity Sensor with Arduino I will tell you that how can you interface temperature and humidity sensor named as DHT11 with Arduino and how can you observe the temperature and humidity level using this sensor. This sensor has usually three pins but some of its types has four pins but only the three pins are of importance for us e.g. VCC, GND and the third pin for reading the data from the sensor.
In the tutorial Interfacing Temperature & Humidity Sensor with Arduino, I will make a simple Arduino program which will estimate the level of temperature and humidity continuously and will display the value of both temperature and hum ...
Hi Guys! Happy to see you around. I welcome you on board. Thank you for clicking this read. In this post today, I’ll walk you through the Introduction to JRC4558.The JRC4558 is a single silicon-chip monolithic dual operational amplifier. This amplifier is a high-performance device and is internally compensated. It is widely used in sample and hold amplifiers and pedal circuit designs. The JRC4558 is available with a remarkable input impedance of around 5 MO, a high voltage gain of around 100 dB, and a good slew rate of around 1.7V/µs.
I suggest you buckle up as I will walk you through the complete introduction to JRC4558 covering datasheet, pinout, features, alternatives, and applications. Let’s jump right in.
Introduction to JRC4558
The JRC4558 is a single silicon-chip mono ...
Hello everyone! I hope you all will be absolutely fine and having fun. Today, I am going to share my knowledge about how to convolve the signals using an amazing software tool, MATLAB. MATLAB is an efficient tool for signal processing. MATLAB basically works on matrices. First of all I would like to tell you a bit about the convolution. In engineering terms, convolution describes the output of the Linear Time Invariant (LTI) systems.
Convolution is basically an integral which tells us about the overlapping of one function as it is shifted over another function. Convolution and cross correlation are similar. It has a wide range of applications e.g. computer vision, probability, statistics, engineering, differential equations, signal processing etc. ...
Hello everyone! I hope you all will be absolutely fine and having fun. Today, I am going to share my knowledge about Generating Simple Signal in MATLAB. Signals are of great importance in our daily life. The signals are basically the graphical display of the analog values. We can estimate the severity level by the shape of the signals. The signals have a very wide range of applications in our daily lives. If we observe the shape of the AC voltages of 220V that is supplied in our homes, it is a sinusoidal signal. So, its an application of the signals.
Signals also play a vital role in the medical field. While performing ECG and EEG tests in hospitals, doctors visualize the signals displayed on the screen and they can estimate the severity of the ...
