Hello everyone! I hope you all will be absolutely fine and having fun. Today, I am going to elaborate you about Introduction to LM1458. Lm 1458 is basically a general purpose dual Operational Amplifier (Op-amp) i.e. it consists of two internal amplifiers. The internal amplifiers has both common power supply as well as common biased network. This is done so that their operation remains dependent on each other.
If the power supply and biasing is not common then they will be totally independent. LM 1458 is a device which is protected from short circuit and it requires no external components for the frequency compensation. LM 1458 is considered to be and ideal amplifier for voltage followers. This is due to its latch-up free operation and high commo ...
Hello everyone! I hope you will be absolutely fine and having fun. Today, I am going to explain all of you about Introduction to 74HC595. It is basically a shift register. It has an ability to store and to shift the data of 8 bits. First of all the data is written on the register serially and then it goes to the storage register. All of the output lines are controlled by this register.
74HC595 register is a very high speed device based on Complementary Metal Oxide Semiconductor (CMOS). 8 bit data register receives the data from the input DS. This data is then transferred from the input shift register to the output shift register. 74HC595 has a vey wide range of applications in daily life. It can be used as serial to parallel data converter, can ...
Hello friends! I hope you all will be absolutely fine. Today, I am going to share my knowledge with all of you guys, on how to make a Temperature Conversion in LabVIEW. Temperature is actually measured with different units at different places all across the world. However, there are three basic standard units for measuring the temperature i.e. Celsius, Fahrenheit and Kelvin. We can convert them in each other by performing some mathematical operations. In this tutorial I am going to elaborate only one of these conversions.
I would like to tell the standards of these scales with reference to the freezing and boiling point of water. "Celsius" scale is basically the scale based on 0 degrees for the freezing point of water and 100 degree for the boil ...
Hello friends, after completing that basic part of ladder logic programming, let us today go through one topic which is not essential to know to complete a PLC ladder program but it is important t have our code readable program and reusable pieces of code. That could happen by using what so-called a subroutine. So what is a subroutine? Well, it is a piece of code that includes a few rungs to perform specific tasks. that piece of code can be reused numerous times through the program when we need to call it for performing that task. That subroutine enables us to structure our code like building blocks so that the program will be readable very easy and also reusable later in other projects. The idea of dividing the program into routines to apply the divide and conquer technique is very crucia ...
Hello everyone, I hope you all are doing great. In today's tutorial, we will have a look at another competitive Fabrication House named NextPCB. Recently, I was working on a project, where I need to design some PCBs and this time, I thought of trying NextPCB.
If anyone ask me, about my experience with NEXTPCB in one word, then I would say splendid !!! So, let's have a look at why we should select NEXTPCB for our next PCB order:
Quick Review about NextPCB
NextPCB, based in China, is working in PCB manufacturing field for 15 years.
They not only design single PCB, but also fabricate PCB Assembly & PCB Stencil.
NextPCB manufacturing materials are certified by IATF 16949, ISO9001, ISO14001, UL, RoHS and REACH.
They work on all types of ...
Welcome to the next tutorial of our raspberry pi programming tutorial. The previous tutorial showed us how to set up a weather station using the Internet of Things (IoT) on a Raspberry Pi 4. First, we studied how a weather station works on a fundamental level. Then we developed a Python script to collect data from the station. In contrast, we'll construct an automatic gate using a Raspberry Pi, a load cell, and an HX711 weight sensor.
These pressure-sensitive gates are common in shopping centers and showrooms; they open when someone is in the immediate vicinity and close again when the person is out of sight. Like the Automatic Gate, we just made, this one will open in response to weight or pressure and stay that way until the force is removed. If ...
Hello friends, I hope you all are fine and having fun with your lives. In today's tutorial, I am going to share a new Flame Sensor Library for Proteus. This Flame Sensor is not available in Proteus and its library is not yet developed anywhere. We are the first ones designing this new Flame Sensor Library for the first time. I am quite excited while sharing it as it's our team efforts that we are able to design new Proteus Libraries which are helpful for students.
We are planning to share more sensor libraries this week. I hope you guys are going to enjoy them and share them with your friends so that they can also know about them. Other bloggers are warmly welcome to share this library on their blogs but do mention our blog link in it as a favor. ...
Hello friends! I hope you all will be absolutely fine and having fun. Today I am going to share my knowledge with all of you guys that how to make a simple program for Quadratic Roots Calculation in LabVIEW. Quadratic equation is a second order basic equation. It plays a vital role for a lot of mathematical problems. The answer obtained from this equation is knows as its roots (also called quadratic roots). It can not have more than two roots. Roots can be 0,1 or maximum 2 and not more than that. We can solve quadratic equation in three different ways, but in this tutorial we will focus on one of them only. Here, I am going to tell you about form and the different ways of Quadratic Roots Calculation.
Ways to Solve Quadratic Equation
The quadratic ...
In today's tutorials, we are going to have a look at escape sequence in C++. In our previous tutorial, Introduction to C++ we have designed a small Hello World program and if you haven't studied it yet then you should first check that one out as I am gonna take it further from there.
In that tutorial, we have designed a code which prints the Hello world on the output screen. The code used for printing it on the output screen is as follows:
How to use Escape Sequence in C++ ??
Now, suppose if I want to print out "Hello World" , instead of Hello World.
In simple words, I wanna add "" these symbols as well on each side of Hello World.
But if you add them in the above program then it will generate er ...
Hello friends, hope you all are fine and having fun with your lives. Today, I am going to share a new exciting post on Send SMS with SIM900D in Proteus ISIS. In my previous post, I have shared the new GSM Library for Proteus, which is the first ever designed library for Proteus, and I am quite excited while sharing its features. So, today, we will use this GSM Lirbary for Proteus and we are gonna send sms with Sim900D module available in that library. We are gonna design this whole project in Proteus ISIS.
If you wanna implement it on hardware then you must have a look at Send SMS with SIM900D module with Arduino which is designed in real hardware but today we are gonna just do the simulation part. Iam not gonna use any Microcontroller today. Inst ...
