Hello friends, hope you all are fine and having fun with your lives. Today, I am going to share a complete project with you guys. Its an Intelligent Energy Saving System which I designed around two years ago. So, today I thought to share it so that others could also get benefit. In this project, I have used Arduino UNO board for programming purposes. Its not much complicated project but is the basic for many complex projects.
Energy, is a small word, but is the problem of whole world. Particularly when we are talking about electrical energy. IF you consume more electrical energy then you will get quite huge bill at the end of the month. :P So, there's always work done on reducing the consumption of electrical energy and also we compare energy cost ...
Hello friends, hope you all are having fun and enjoying life. Today's post is quite a simple one and is about designing of circuit diagram of buzzer in Proteus ISIS. Buzzer is quite a common electrical component which is used in almost every Embedded Systems project. For example, you have seen a simple UPS, it gives a beep each time the light goes off or it has depleted its battery. Buzzer is normally used for given some indication and normally this indication is kind of a warning.
Proteus has a builtin component for buzzer and its an animated component means it gives a sound (beep) when its turned ON. So, I am gonna use that one and will give you an actual beep on it. So, it won't be much difficult and quite a simple procedure. In this post, I am ...
Hello friends, hope you all are fine and having fun with your lives. Today I am going to share a problem and also its solution with you guys. A few days ago, I bought new NRF24L01 modules as they were needed for a project. So, today when I started working on them, I encountered a very strange problem. When I interfaced my NRF24L01 with Arduino and uploaded the transmitting and receving codes in them, I couldn't get anything on my serial terminal as I explained in my previous post Interfacing of NRF24L01 with Arduino. That was quite strange for me as I have worked on this module many times and it never troubled me before. So I keep on working on it but no luck. I even changed my RF modules as I thought may be they are faulty modules but still no lu ...
Hello friends, I hope you all are fine and enjoying yourself. Today I am going to share a new project titled Interfacing of temperature sensor LM35 with Arduino UNO in Proteus ISIS. So far, I have only worked on temperature sensor DS18B20 for temperature measurements and I have also uploaded a tutorial on Interfacing of Temperature Sensor 18B20 with Arduino.
Recently I got a chance to work on a project regarding temperature sensing but the condition of this project was that to use only LM35 for temperature detection. Then, I get to know much about LM35, its operating conditions and features. So I thought I should also upload its tutorial as it will also be advantageous for engineering students. Because learning new things is always a charm.
An exc ...
Buy This Project
Hello Friends, i hope you all are fine and enjoying. Today i am going to share my new project tutorial which is 3 level cascaded H bridge Inverter. I also have explained inverters in detail in one of my previous tutorial which was Introduction to Multilevel Inverters. In this tutorial i am going t o explain a new application of cascaded H-bridge inverters and we will design a 3-level cascaded H bridge Inverter through it.
Before going to that, first of all lets recall some basics of Inverters from our previous posts. Inverters or commonly known as power inverters and A dc-to-ac converter whose output is of desired output voltage and frequency is called an inverter. Inverters are also called as counter devices of rectifiers. Rect ...
Buy This Project
Hello friends, hope you all are fine and enjoying. Today i am going a new project tutorial which is 11-level 3-phase Capacitor Clamped Inverter. In my previous post 11 Level 3-phase Cascaded H-Bridge Inverter, we have designed the simulation of 3 phase 11 level inverter but the only difference was the method used in that project was cascaded H Bridge but today we are gonna see How to design an 11 level 3 phase inverter using clamped capacitors.
Now i am going to share a new and advanced bulk of knowledge about inverters with you people. Since we are going to design a 3-phase capacitor clamped inverter so, we need to design some algorithm which should be able to invert DC into AC at some High voltages and after inverting these DC ...
Hello everyone, hope you all are fine and having fun with your lives. Today's tutorial is quite simple and we will have a look at circuit diagram of IR sensor using 555 Timer. There are different types of IR sensors available in the market. IR is abbreviation of infrared and so they use infrared ray for detection of objects. There are many types of IR sensors with different functionality, but in all of them infrared rays are omitted from transmitter and are received by the receiver. and using these ray we can say whether an object is placed in the path or not.
Today we are gonna see how to design your own IR sensor using 555 Timer. We can also interface these IR sensors quite easily with any microcontroller like PIC Microcontroller , Arduino etc. ...
[LM317TEP]
Hello friends, I hope you all are doing great. Today, I am going to share our new online tool which is named as LM317 Calculator. I am quite excited while posting this LM317 Calculator, as I was trying for a long time to post it but couldn't done it because of few problems. Anyways, its here now and is ready to be utilized. Its nothing but a simple LM317 Calculator. I have included two LM317 calculators posted above, one will be used to calculate the Vout while the other will be used to calculate the resistance (R1).
You should have a look at Introduction to LM317, if you don't know much about it. LM317 is an IC regulator which is used to regulate the output voltage and its output voltage is regulated depending on the values of both the resistances attached at its output. He ...
Hello friends, hope you all are fine and having fun with your lives. Today, I am going to share a Traffic Signal Control using Arduino. Few days earlier, I have posted the same tutorial but it was Traffic Light Signal Using 555 Timer in Proteus ISIS and today we will do the same thing but using Arduino programming. Its quite a simple but good starting project on Arduino. So, if you are new to Arduino then must give it a try.
Traffic Signal Control is quite a usual thing. We see traffic signals daily on our roads and usually engineers are asked to design such projects in their initial semesters. If we look at the traffic signals then we can see they are simply turning ON and OFF lights at some fixed regular intervals. and the pattern is quite simpl ...
Hello friends, hope you all are fine and having fun with your lives. Today's post is about interfacing of RFID module RC522 with Arduino. RC522 is very simple yet effective module. It is an RFID module and is used for scanning RFID cards. Its a new technology and is expanding day by day. Now-a-days it is extensively used in offices where employees are issued an RFID card and their attendance is marked when they touch their card to rfid reader. We have seen it in many movies that when someone places ones card over some machine then door opens or closes. In short, its a new emerging technology which is quite useful.
I recently get a chance to work on a project in which I have to use RFID reader to scan cards. In this project I have used it for for s ...
