TEP DOWNLOAD CENTER

Project Files of MPPT Solar Charge Controller Library for Proteus Simulation

Libraries Code Projects Simulation
tep://download-terminal 0c500441526b42788a367c2538832c10.zip ZIP archiveV1.0Verified0 downloadsFree
MPPT Solar Charge Controller Library for Proteus Simulation: an Arduino UNO V4.0, the MPPT controller, a solar panel, our INA219 and a lead-acid battery
Proteus library · File 1 of 1

MPPT Solar Charge Controller Library for Proteus V1.0

MPPT Solar Charge Controller Library for Proteus V1.0 comes as a ZIP archive of 16 files (1.9 MB, 3.9 MB unpacked) holding Proteus library files, simulation model DLLs, a Proteus simulation, an Arduino sketch and compiled HEX firmware.

  • LIBProteus library
  • DLLProteus model
  • DSNProteus simulation
  • INOArduino sketch
  • HEXHEX firmware

Description

MPPT-Solar-Charge-Controller-Library-for-Proteus-v1.0.zip with the MPPT solar charge controller for Proteus simulation (TEPMPPT.LIB and TEPMPPT.DLL), our 12V solar panel, our 12V lead-acid battery, our Arduino UNO V4.0, the A3 demo with its sketch and a README.

Read MPPT Solar Charge Controller Library for Proteus Simulation

File Structure

0c500441526b42788a367c2538832c10.zip16 files · 5 folders · 3.9 MB unpacked
MPPT-Solar-Charge-Controller-TEP-v1.0/16 files · 3.9 MB
Arduino Code/1 file · 5.3 KB
MpptCharge_Demo/1 file · 5.3 KB
INO MpptCharge_Demo.inoArduino sketch 5.3 KB
Proteus Library Files/4 files · 274.7 KB
LIB ArduinoV4TEP.LIBProteus library 201.9 KB
LIB TEPLEADACID.LIBProteus library 16.2 KB
LIB TEPMPPT.LIBProteus library 16.1 KB
LIB TEPSOLAR.LIBProteus library 40.5 KB
Proteus Model Files/4 files · 1.8 MB
DLL TEPARDUINO.DLLSimulation model 883.5 KB
DLL TEPLEADACID.DLLSimulation model 325 KB
DLL TEPMPPT.DLLSimulation model 322.5 KB
DLL TEPSOLAR.DLLSimulation model 311.5 KB
Proteus Simulation/6 files · 1.9 MB
DSN MPPT-Solar-Charge-Controller-Battery-INA219-ArduinoUnoV4.pdsprjProteus simulation 27.7 KB
HEX MpptCharge_Demo.hexCompiled HEX file 26.3 KB
DLL TEPARDUINO.DLLSimulation model 883.5 KB
DLL TEPLEADACID.DLLSimulation model 325 KB
DLL TEPMPPT.DLLSimulation model 322.5 KB
DLL TEPSOLAR.DLLSimulation model 311.5 KB
TXT README.txtText file 18.5 KB

README

README.txt 307 lines
MPPT SOLAR CHARGE CONTROLLER LIBRARY FOR PROTEUS SIMULATION - V1.0 (12 V / 24 V, 10 A, three lamps and a pop-up)
Designed by The Engineering Projects
www.TheEngineeringProjects.com

IMPORTANT LINKS
Article (read it first - pictures, step by step, every feature explained):
  https://www.theengineeringprojects.com/2026/11/mppt-solar-charge-controller-library-for-proteus.html
Report a bug or suggest a feature (our forum):
  https://www.theengineeringprojects.com/forum/category/motor-driver-proteus-library
The demo runs on our Arduino UNO V4.0 (included) - working LEDs, RESET and a
built-in serial monitor, no Virtual Terminal to wire - its own article:
  https://www.theengineeringprojects.com/2026/10/arduino-uno-library-for-proteus-v40.html
The demo measures the battery with our INA219 library (installed from its own package - not in this zip):
  https://www.theengineeringprojects.com/2026/10/ina219-current-sensor-library-for-proteus-v1-0.html
The demo's panel is our 12V Solar Panel library (its LIB and DLL are in this zip; its own article):
  https://www.theengineeringprojects.com/2026/11/12v-solar-panel-library-for-proteus-v1-0.html
The demo's battery is our 12V Lead-Acid Battery library (its LIB and DLL are in this zip; its own article):
  https://www.theengineeringprojects.com/2026/11/12v-lead-acid-battery-library-for-proteus.html
The same system with a PWM controller, to compare (its own package and article):
  https://www.theengineeringprojects.com/2026/11/pwm-solar-charge-controller-library-for-proteus.html
Support us (the libraries are free):
  https://www.theengineeringprojects.com/donate

FILE STRUCTURE
MPPT-Solar-Charge-Controller-TEP-v1.0/
|-- Proteus Library Files/
|   |-- ArduinoV4TEP.LIB                              201.9 KB   TEP Arduino boards V4.0 (UNO) -> LIBRARY
|   |-- TEPLEADACID.LIB                                16.2 KB   a part the demo uses -> LIBRARY folder
|   |-- TEPMPPT.LIB                                    16.1 KB   the library -> LIBRARY folder
|   |-- TEPSOLAR.LIB                                   40.5 KB   a part the demo uses -> LIBRARY folder
|-- Proteus Model Files/
|   |-- TEPARDUINO.DLL                                883.5 KB   the Arduino board model -> MODELS folder
|   |-- TEPLEADACID.DLL                               325.0 KB   its model -> MODELS folder
|   |-- TEPMPPT.DLL                                   322.5 KB   the model -> MODELS folder
|   |-- TEPSOLAR.DLL                                  311.5 KB   its model -> MODELS folder
|-- Proteus Simulation/
|   |-- MpptCharge_Demo.hex                            26.3 KB   the demo firmware
|   |-- MPPT-Solar-Charge-Controller-Battery-INA219-ArduinoUnoV4.pdsprj   27.7 KB   the demo project
|   |-- TEPARDUINO.DLL                                883.5 KB   copy of the board model
|   |-- TEPLEADACID.DLL                               325.0 KB   copy of its model
|   |-- TEPMPPT.DLL                                   322.5 KB   copy of the model
|   |-- TEPSOLAR.DLL                                  311.5 KB   copy of its model
|-- Arduino Code/
|   |-- MpptCharge_Demo/MpptCharge_Demo.ino             5.3 KB   the demo sketch (source of the .hex)
|-- README.txt                                        ~19.3 KB   this file
Total: 3.94 MB (unzipped). The C++ source code of the models is not included.

WHAT IS IT?
A compact MPPT solar charge controller - 12 V / 24 V, 10 A, a finned aluminium case of 100 x 91.5 mm
with three lamps -
drawn at true scale (the case, the label plate with the PV, BATTERY and LOAD lamps, three pairs of
leads; our own drawing,
no maker's mark). The figures are from a maker's data sheet of such a controller:
  * MPPT, maximum power point tracking: the controller is a converter. It holds the panel at the
    voltage where the panel
    gives the most power (about 17.6 V for a 36-cell panel) and turns the extra volts into charge
    current: MORE amperes
    go into the battery than come out of the panel. A PWM controller wastes that difference.
  * The tracker works by perturb and observe, 50 times a second: it loads the panel a little more or
    a little less and
    keeps the direction that gave more power. It follows the light and the battery's voltage by
    itself.
  * BULK with all the power the panel has (10 A of charge at most); BOOST at 14.4 V for two hours,
    where only the power
    that holds this voltage is taken and the panel moves off its best point; FLOAT at 13.8 V. Under
    13.2 V it starts again.
    A LiFePO4 battery (LFP): 14.4 V until the current is under 0.5 A, then the charge pauses until
    13.2 V.
  * No sun: the converter stops when the open panel is less than 2 V above the battery. Nothing can
    flow back.
  * The load leads: cut when the battery is under 11.1 V, back at 12.6 V; cut on an overload.
    LOADMODE as the PWM part.
  * The three - leads are joined inside (a common-negative controller): one ground for the panel,
    the battery and the load.
  * On the sheet the three lamps work at Run and the label plate shows the stage and both sides of
    the conversion: the
    panel's volts and amps, and the battery's. Click it at Run for the pop-up: the power flow, the
    power curve the
    tracker has climbed, the stages, eight live values; graphs, an event log and a check page.
The body is drawn as on the real part and to true scale against our Arduino.
The TEP signature and the pop-up are TEP additions.

ONE DEVICE (search "MPPTCHARGE" in Pick Devices):
  MPPTCHARGECONTROLLERTEP  "MPPT Solar Charge Controller 12 V / 24 V 10 A V1.0" in TEPMPPT.LIB
  (Electromechanical > Charge
                           Controllers), prefix CC, model TEPMPPT.DLL (analog). Six pins along the
                           bottom, at the ends of
                           the leads: PV+ PV- (the panel), BAT+ BAT- (the battery), LOAD+ LOAD- (the
                           load). The name
                           starts with M so that it sorts after the embedded ARDUINO UNO V4.0.

THE POP-UP
Click the part at Run. Tabs:
    Controller chips: the load on or off; the battery type (SLA, LFP); the clock (x 1, x 60, x
    3600). The power flow from
               the panel through the converter to the battery and the load, with the volts and amps
               on both sides; the
               points of the panel's power curve the tracker has visited, the best one ringed, the
               panel now as a dot;
               the three stages with the one now lit; eight live values: the panel's volts and amps,
               its power against
               the best seen, the battery voltage with the aim, the charge current, the load, the
               amperes out for each
               ampere in, the amp-hours in and to the load, the stage's time or voltage.
    Graphs     the live values over the last 2, 6 or 15 s. Live / Freeze.
    Event log  every change and warning; filters All / Changes / Warnings, Pause, Clear
    Check      what the part is doing and what to look at, each with a verdict (green = fine, amber
    = check, red = wrong)
    Settings   theme, text size, open at Run, window size
    Help       report a bug, suggest a feature, article, updates, donate, forum; Copy diagnostics
    for a bug report

TEST STATUS
V1.0: verified in Proteus 8.5 on 16 Nov 2026 (the demo project as shipped: an A3 sheet, an Arduino UNO V4.0).
What the runs showed (the model's own numbers and the sketch's monitor):
The demo as shipped (MpptCharge_Demo; PV1 20 W in full sun, CC1 SLA 12 V with the load always on,
BAT1 SOC 75 %, R1 22 ohm,
SPEED 3600 on the battery and the controller), one run (mpfinal2), the model's own pauses:
  * BULK from 60 ms: the open panel gives 21.6 V, the battery is at 12.51 V. The tracker climbs
    (0.24 s: the panel at 21.3 V,
    3.3 W in, the best so far 8.3 W at 20.8 V) and is at the top at 0.54 s: 20.0 W at 17.7 V. At 0.6
    s the panel is held at
    17.6 V: 1.14 A, 20.0 W in, 1.48 A into the battery side at 13.09 V (x 1.30), 0.59 A to the load.
    At 1.5 s the panel's
    pop-up: 17.60 V, 1.134 A, 19.96 W (all this light gives); the battery's pop-up: 0.78 A in at
    13.40 V, 86 %; the INA219
    (U1): 13.408 V on the bus, 78.13 mV on the shunt, 781.3 mA into the battery.
  * BOOST at 2.460 s (14.4 V): 16.3 W taken, the panel at 19.6 V and 0.83 A, 1.10 A at 14.42 V, 1 h
    45 min left (2.7 s);
    12.4 W taken, the panel at 20.3 V and 0.61 A, 0.83 A at 14.41 V, 1 h 03 min left (3.4 s).
  * FLOAT at 4.460 s: 9.4 W taken, the panel at 20.7 V and 0.45 A, 0.66 A at 13.80 V, 0.63 A to the
    load (4.8 s to the end).
  * In all 93.7 Wh from the panel, 6.59 Ah (90.9 Wh) into the battery side and 4.39 Ah (60.8 Wh) to
    the load; the battery
    between 12.50 V and 14.50 V (the top a short overshoot as the boost stage began); the panel's
    highest voltage 21.6 V,
    its most power 20.0 W; the most charge current 1.48 A.
  * The monitor named the stages from the battery's side: bulk charge with up to +0.85 A, boost
    charge at 14.39 - 14.40 V
    while the current fell from +0.50 A to +0.06 A, float charge at 13.80 V with +0.02 A; it ended
    at +2.07 Ah and 28.2 Wh.
    152 s for the 7.0 s of the run.
A second run under clouds (mpcloud2: IRRADIANCE 300 on the panel): the tracker finds the new top,
5.7 W at 16.8 V; at 1.5 s
the panel's 0.34 A at 16.7 V become 0.44 A at 12.53 V; the load takes 0.57 A, so the battery makes
up the rest.
A third run at night (mpcheck2: IRRADIANCE 0 on the panel, SOC 12 % on the battery): NO SUN, the
converter is off; the battery
feeds the load, 0.53 A at 11.64 V (0.4 s); LOAD CUT at 1.320 s with the battery down to 11.10 V; the
load stays off, the
battery back at 11.16 V (1.6 s).

INSTALLATION (about 2 minutes)
1. Close Proteus. Extract the WHOLE ZIP to a normal folder (e.g. Desktop).
2. Copy everything in "Proteus Library Files" (TEPMPPT.LIB, TEPSOLAR.LIB, TEPLEADACID.LIB and our
Arduino library V4.0, ArduinoV4TEP.LIB, with the ARDUINO UNO V4.0 used by the demo) to the LIBRARY
folder of Proteus, for example:
     C:\Program Files (x86)\Labcenter Electronics\Proteus 8 Professional\LIBRARY
   (use the folder that already holds Proteus's own .LIB files).
3. Copy TEPMPPT.DLL, TEPSOLAR.DLL, TEPLEADACID.DLL and TEPARDUINO.DLL from "Proteus Model Files" to
the MODELS folder (...\Proteus 8 Professional\MODELS).
4. Delete TEPMPPT.IDX from the LIBRARY folder if it is there (Proteus makes a new index).
5. Start Proteus. In Pick Devices (P) search "MPPTCHARGE".

RUN THE DEMO
"Proteus Simulation\MPPT-Solar-Charge-Controller-Battery-INA219-ArduinoUnoV4.pdsprj" (an A3 sheet) -
keep the .hex file and the DLLs beside the project.
  The small solar system of our PWM controller's demo, with the MPPT controller in its place:
  ARD1:   Arduino UNO V4.0 running MpptCharge_Demo.hex, its serial monitor built in (window "TEP
  Arduino UNO - ARD1").
  PV1:    our 12V Solar Panel, 20 W, in full sun (1000 W/m2): + to the controller's PV+ (the label
  PV+), - on ground.
  CC1:    the MPPT solar charge controller: BATTERY SLA, 12 V, load always on, SPEED 3600; PV- and
  BAT- on ground.
  U1:     our INA219 (its pop-up version) between the controller's BAT+ (VIN+) and the battery's +
  (VIN-); SDA A4, SCL A5.
  BAT1:   our 12 V 7.2 Ah lead-acid battery, SOC 75 %, SPEED 3600 (an hour each simulated second), -
  on ground.
  R1:     22 ohm on LOAD+ / LOAD-: a 12 V lamp of about 7 W.
          The sketch takes sixteen readings and works with their mean, tells the stage from the
          battery's voltage and
          current, and counts the amp-hours and the watt-hours; the UNO's LED lights while the
          battery is charged.
Closed the monitor? Click the UNO's USB port.

WIRING (the same in Proteus and on a real board)
  Connect the battery first, then the panel, then the load. PV+ / PV- to the panel, BAT+ / BAT- to
  the battery, the load on
  LOAD+ / LOAD-. The three - leads are joined inside, so the panel's -, the battery's - and the
  load's - may share one
  ground. The panel must give at least 2 V more than the battery at its best point, and never more
  than 60 V open.
REAL HARDWARE:
 * The panel's power sets the size: 10 A of charge is about 130 W of panel in a 12 V system and 260
   W in a 24 V system.
 * A panel with more volts suits an MPPT controller well (two 36-cell panels in series, under 60 V
   open): the converter
   turns the volts into amperes. A PWM controller could not use them.
 * A fuse belongs in the battery lead. A load that starts with a surge belongs on the battery, not
   on the LOAD leads.

THE DEMO SKETCH ON THE SERIAL MONITOR (MpptCharge_Demo V1.0, 9600 baud)
The sketch reports every 500 ms. Type a command:
  reset      the counters back to 0       rate 1000      report every 1000 ms       help
EXPECTED MONITOR OUTPUT
  Solar battery monitor - The Engineering Projects
  + A: into the battery, - A: out of it. Clock x 3600: a simulated second is an hour.
  Commands: reset | rate 500 | help
  Battery 12.56 V  -0.34 A  -4.3 W  the battery feeds the load  +0.00 Ah  0.0 Wh
  Battery 13.02 V  +0.85 A  11.1 W  bulk charge  +0.21 Ah  2.7 Wh
  Battery 13.25 V  +0.81 A  10.7 W  bulk charge  +0.71 Ah  9.3 Wh
  ...
  Battery 14.40 V  +0.50 A  7.1 W  boost charge  +1.70 Ah  22.9 Wh
  Battery 14.39 V  +0.21 A  3.0 W  boost charge  +1.90 Ah  25.8 Wh
  ...
  Battery 13.80 V  +0.02 A  0.3 W  float charge  +2.07 Ah  28.2 Wh

PROPERTIES (double-click the part > Edit Properties)
  Battery type (BATTERY)               SLA lead-acid (sealed, gel, AGM) or LFP LiFePO4 4S (SLA)
  System voltage (SYSTEM)              12 or 24; 24 doubles every battery voltage (12)
  Load mode (LOADMODE)                 24 always on, 0 dusk to dawn, 1 - 23 hours after dusk (24)
  Clock (SPEED)                        1 real time, 3600 an hour each simulated second - the same as
  the battery's, 1 - 7200 (1)
Every run starts again from the properties.

LINKS.INI (OPTIONAL)
The Help page cards of the pop-up open web pages. To point them somewhere else without a new DLL,
put a text file named links.ini next to TEPMPPT.DLL with lines KEY=URL, for example:
  ARTICLE=https://www.theengineeringprojects.com/...
Keys: WEBSITE, FORUM, BUG_REPORT, FEATURE_REQUEST, ARTICLE, USER_GUIDE,
UPDATE_CHECK, DONATE. Only http:// and https:// links are used; lines starting
with # are comments.

TROUBLESHOOTING
* NO SUN although the panel is lit: the open panel is less than 2 V above the battery. An MPPT
  (buck) controller needs a
  panel with more volts than the battery: a 36-cell panel for 12 V, 72 cells or two panels in series
  for 24 V.
* NO BATTERY: under 9 V on BAT+ / BAT-. The controller is powered by the battery: connect it first.
* The panel is not at its best point: the battery is in the boost or float stage and cannot take all
  the power, or the
  charge current is at the controller's 10 A. That is how the controller limits the charge - no
  fault.
* The load is off: the battery fell under 11.1 V (it comes back at 12.6 V), the load mode waits for
  the night, or an overload.
* The stage never leaves BULK: the panel is too small for the load, or the two-hour clock runs in
  real time - set SPEED as
  the battery's (60 or 3600).
* The part is not simulated: TEPMPPT.DLL is missing from MODELS and from the project folder. No UNO
  / no monitor window: TEPARDUINO.DLL is missing, or click the UNO's USB port.

BUG REPORTS AND FEATURE REQUESTS
Please post them in our forum with a screenshot, the Serial Monitor text, the
simulation log and the pop-up's Copy diagnostics text:
  https://www.theengineeringprojects.com/forum/category/motor-driver-proteus-library

SUPPORT US
This library is free. If it saves you time, please support our work:
  https://www.theengineeringprojects.com/donate

WEBSITE
  https://www.theengineeringprojects.com/

LICENCES AND THIRD-PARTY NOTES
* The model (TEPMPPT.DLL), the symbols and artwork, the other parts of ours in the demo and the
  Arduino Library V4.0 (ArduinoV4TEP.LIB / TEPARDUINO.DLL, with its built-in TEP Serial Monitor
  Advance) are made by The Engineering Projects. The models use only standard Windows libraries; no
  Visual C++ redistributable is needed.
  The C++ source code is not included.
* Arduino UNO V4.0 (ArduinoV4TEP.LIB / TEPARDUINO.DLL, our Arduino Library V4.0 - its
  microcontroller is Proteus's own AVR model): The Engineering Projects,
  https://www.theengineeringprojects.com/2026/10/arduino-uno-library-for-proteus-v40.html
* The .hex file is built from the demo sketch and the Arduino AVR core 1.8.6, which includes
  LGPL-licensed code; its source code is available at
  https://github.com/arduino/ArduinoCore-avr/tree/1.8.6
* Proteus is a product of Labcenter Electronics and is not included. Arduino is a trademark of Arduino SA.
  This library is not made or endorsed by Arduino or Labcenter.

REBUILDING THE FIRMWARE (OPTIONAL)
The HEX file is supplied; Arduino IDE is not needed to run the demo. To edit the sketch, open
Arduino Code\MpptCharge_Demo\MpptCharge_Demo.ino, select Arduino Uno and use Sketch > Export
Compiled Binary. Replace the simulation's .hex with the exported HEX. The sketch needs 9,576 bytes
of flash and 512 bytes of RAM.

MODEL SCOPE AND LIMITS
Modelled: the converter by its mean (the panel sees a conductance, the battery gets 97 % of the
panel's power as a current
- 97 % is ours, the sheet says 98 % at the peak); the tracker by perturb and observe, 50 steps a
  second (ours); the
stages with the voltages of makers' manuals (boost 14.4 V for 2 h, float 13.8 V, again under 13.2 V;
LiFePO4 14.4 V to
0.5 A); the 10 A charge limit; the load cut at 11.1 V and back at 12.6 V (LiFePO4 11.2 / 12.3 V);
the over-voltage cut; the
panel's 60 V limit; the 9 V the controller needs; its own 14 mA; the three lamps; the load modes;
the common negative.
Not modelled: the converter's switching (far above what a circuit simulation can step through) and
its ripple, the RS485
port and the cloud, the trickle start of a deeply discharged battery, the temperature sensor, the 20
A fuse, the
controller's heat; the 2 V of headroom, the delays and the short-circuit level are ours.

VERSION
TEP MPPT Solar Charge Controller library V1.0 (Nov 2026). Device MPPTCHARGECONTROLLERTEP
(TEPMPPT.LIB / TEPMPPT.DLL). Demo sketch MpptCharge_Demo V1.0 (the INA219 read straight with Wire).
The demo also uses our 12V Solar Panel (TEPSOLAR: SOLARPANELTEP) and our 12V Lead-Acid Battery
(TEPLEADACID: LEADACIDBAT12V7TEP), shipped in this package. Demo board: ARDUINO UNO V4.0 (TEP
Arduino Library V4.0) with its built-in serial monitor.
Advertisement

Development1 release

  1. V1.0MPPT Solar Charge Controller Library for Proteus V1.0this page

    V1.0 is the only release in the Download Center so far. When a newer version is published, it appears above with its own download page.

Installation8 steps

From the download to a working project, in order. The steps follow what the package contains.

You will need

  • Proteus Design SuiteProteus 8 or newer (Labcenter), on Windows
  • Arduino IDE1.8 or 2.x, with the board of the tutorial chosen under Tools → Board
  • Any archive toolWindows, macOS and Linux extract ZIP files on their own

Steps

  1. 1

    Extract the archive

    Right-click 0c500441526b42788a367c2538832c10.zip and choose Extract All (or open it with 7-Zip or WinRAR) into a folder you can find again. Keep its folder structure (MPPT-Solar-Charge-Controller-TEP-v1.0) as it is.

  2. 2

    Copy the library files into Proteus

    Move ArduinoV4TEP.LIB, TEPLEADACID.LIB and TEPMPPT.LIB and 1 more and the files into the LIBRARY folder of your Proteus installation: C:\Program Files (x86)\Labcenter Electronics\Proteus 8 Professional\LIBRARY for Proteus 8, or the matching Proteus 7 folder. Older versions keep it under ProgramData\Labcenter Electronics. If Proteus is open, close it first.

  3. 3

    Add the simulation model

    Copy TEPARDUINO.DLL, TEPLEADACID.DLL and TEPMPPT.DLL and 1 more into the MODELS folder next to LIBRARY, so the component can run, not only be drawn.

  4. 4

    Restart Proteus and place the component

    Start Proteus, open a schematic, press P (Pick Devices) and search for the component by the name used in the tutorial. It appears with its pins ready to wire.

  5. 5

    Open the sketch in the Arduino IDE

    Open MpptCharge_Demo.ino, select your board and port under Tools, then Verify. Sketch → Export Compiled Binary writes the HEX file a simulation needs.

  6. 6

    Load the HEX file

    In Proteus double-click the microcontroller, set Program File to MpptCharge_Demo.hex and run the simulation. For real hardware, flash the same file with your programmer.

  7. 7

    Open the example simulation

    Open MPPT-Solar-Charge-Controller-Battery-INA219-ArduinoUnoV4.pdsprj in Proteus to see the wiring exactly as in the tutorial. Check the controller's Program File path, then press Play.

  8. 8

    Follow the tutorial

    MPPT Solar Charge Controller Library for Proteus Simulation explains every connection and setting in order; keep it open beside the files while you build.

How to add a library in Proteus 8

FAQs9 questionsContact TEP

How do I download MPPT Solar Charge Controller Library for Proteus V1.0?

Wait for the 30-second guest countdown on this page, then press the download button; the file comes straight from our storage. Members who are logged in skip the wait. If the browser opens the file instead of saving it, use its Save as option. The download link is made for you when the countdown ends and works for 15 minutes; a saved or shared link stops working, so share this page instead.

What is inside the archive?

MPPT Solar Charge Controller Library for Proteus V1.0 comes as a ZIP archive of 16 files (1.9 MB, 3.9 MB unpacked) holding Proteus library files, simulation model DLLs, a Proteus simulation, an Arduino sketch and compiled HEX firmware. Open the File Structure tab for the full list of 16 files.

What should I do if the download does not start?

Check the browser's download list first; an ad blocker or a company firewall can also hold it back, so try another browser or network. If the file arrives incomplete, download it again. For an installation problem, read the Install tab or tell us in the comments with your software version and the exact error message.

Is this file free?

Yes. Every file in the TEP Download Center is free for learning, personal and student projects. If you share it, link back to this page or the tutorial so others find the latest version.

How do I check that the file arrived complete?

Compare its SHA-256 with the one on this page, 5e9f356dc78bf4224f09e358fbb79a9d827cb065ead16add3b762fd3b854f433. In PowerShell run Get-FileHash "0c500441526b42788a367c2538832c10.zip"; on macOS or Linux run shasum -a 256 "0c500441526b42788a367c2538832c10.zip". The same value means the file is exactly the one in our storage; a different one means the download broke off, so download it again.

Do I need WinRAR to open the ZIP file?

No. Windows, macOS and Linux open ZIP archives on their own (Extract All, or double-click). WinRAR and 7-Zip work too. Extract the whole archive before using the files.

Where do I put the LIB and IDX files?

Both files go into the LIBRARY folder of your Proteus installation (Proteus 8: C:\Program Files (x86)\Labcenter Electronics\Proteus 8 Professional\LIBRARY; Proteus 7 has the same folder under its own name). Restart Proteus afterwards and search for the component with P.

Which Proteus version does the library need?

The tutorial names the Proteus version the library was made and tested with. Most TEP libraries work in Proteus 7 and Proteus 8; if the component does not appear after a restart, check that both the LIB and the IDX file were copied and that Proteus was fully closed while copying.

How do I get the HEX file into the simulation?

Compile the sketch in the Arduino IDE (Sketch → Export Compiled Binary gives you the HEX next to the sketch), then in Proteus double-click the board, set Program File to that HEX and run.

preparing · 0c500441526b42788a367c2538832c10.zip
Rating
Your download will be ready shortly
Preparing your download…

Members skip the wait. Log in or join TEP.

  • 0Total downloads
  • 4%Popularity
  • ProteusCategory
  • 0Comments
  • ssyedzainnasirUploaded by
  • 16 Nov 2026Uploaded at
Last 14 days0 downloads
SHA-256 5e9f356dc78bf4224f09e358fbb79a9d827cb065ead16add3b762fd3b854f433
DocumentationMPPT Solar Charge Controller Library for Proteus Simulation
Need help with this file? Bug report Ask a question Download problemsGet updates
Advertisement

Comments

0

Join the conversation

Start the conversationAsk a question or share how you used this download.