Legacy software refers to a business operating software that has been in use for a long time. This is older system software that is still relevant and fulfills the business needs. The software is critical to the business mission and the software operates on specific hardware for this reason.
Generally, the hardware in this situation has a shorter lifespan than the software. With time, the hardware becomes harder to maintain. Such a system will either be too complex or expensive to replace. For that reason, it continues operating.
What is a Legacy System?
Legacy software and legacy hardware are often installed and maintained simultaneously within an organization. The main changes to the legacy system typically only replace the hardware. That helps ...
Buy This Project
Hello friends, I hope you all are doing great. In today's tutorial, I am going to share Eye Ball Detection in MATLAB. I have designed this simulation in MATLAB and I have designed a GUI in which I am detection the Eye Balls from Images. Our team has worked quite hard in designing this project so we haven't shared the code for free. Instead we have placed a very small amount and you can buy it from our shop via PayPal. Click the above button in order to buy the project.
If you are having any difficulty in buying this project then you can also ask in comments and we will surely help you out. Moreover, this algorithm has a small restriction that the person's eyes must be open in the image and his/her eye balls must be clearly visibl ...
Hello friends, hope you all are fine and having fun with your lives. In today's tutorial, I am gonna show you How to Configure NI MyRio on Wifi. In our previous tutorial, Getting Started with NI MyRio I have show you how to get started with NI MyRio and control LEDs of NI MyRio but you have seen that we have done that over USB. In simple words, we have controlled the LEDs and gyroscope of MyRio over USB but in today's tutorial, first of all, we are gonna configure NI MyRio on Wifi and then we are gonna control all those things over Wifi instead of USB.
If you have a project on MyRio then its my recommendation to use Wifi instead of USB for upload and testing your codes because Wifi is quite flexible in use and you no more restricted to use the USB ...
Buy This Project
Hello friends, I hope you all are fine and enjoying. Today i am going to share a new project which is Fault Detection of Gas Turbine in MATLAB. In this project, i will try to elaborate that, What is a Gas Turbine? What are the operating parameters of a Gas Turbine? Mostly what type of Faults and Vibrations comes in Gas Turbine system during its operation? Gas Turbine is also called a Combustion Turbine. It has Four Basic components which includes Compressor, Combustion Chamber, Turbine and Alternator.
Generally compressor is installed upstream and the Rotating turbine is connected downstream and the Combustion Chamber is connected in between both of them and at the end of line we have Alternator which is also connected on the sa ...
Buy This Project
Hello friends, today I am going to post a complete project designed on MATLAB named as Modelling of DVB-T2 system using Consistent Channel Frequency in MATLAB. This project is designed by our team and it involved a lot of effort to bring it into existence that's why its not free but as usual I have discussed all the details below related to it, which will help you understanding it and if you want to buy it then you can click on the Buy button shown above.
This project aims to implement a DVB-T2 (Digital Video Broadcasting for terrestrial television) system using consistent channel frequency responses. Tthe code is designed to use the same output from a channel model for different transmitter configurations so that consistency of ...
Hello everyone! I hope you all will be absolutely fine and having fun. Today, I am going to share my knowledge about How to use Print MATLAB. As you all know that the design of an algorithm is not enough until we observe its results too. So, there should be a debugging tool in order to check the performance and accuracy of the designed algorithm. Debugging tool helps us to improve the algorithm’s performance and accuracy too by observing its output again and again. In this tutorial I will tell you about using print command in MATLB for different purposes. So, in this tutorial I am going to use print command as a debugging tool in order to observe the output of the algorithm. You should also have a look at how to use MATLAB ?
I am going to use pr ...
Hello Learner! Welcome to another exciting experiment at The Engineering Projects. We hope you are having a great day. In this lecture, we'll seek information about the Boost Converter Circuit from scratch to result in quick and easy steps. So, if you don't know about the experiment then don't worry because every Expert was once a Beginner. We'll talk about the following topics:
What is IRFZ44N MOSFET Boost Converter?
What is the brief introduction of components of circuit?
How can we implement the IRFZ44N MOSFET to design circuit of Boost Converter?
You will know some useful information about the topic in the DID YOU KNOW sections.
IRFZ44N MOSFET Boost Converter
During the experimentation of electronic circuits, we often face the situation ...
Hello everyone! I hope you all will be absolutely fine and having fun. Today, I am going to share my knowledge about Multi Color Detection in MATLAB. Color Detection scheme plays a vital role at some places. Like in Image processing technique the detection of specific color among the different colors is necessary to perform some action on it. For example there are three cars of the colors red, blue and green and we want to wash the red car. You should also have a look at Color Detection in Images using MATLAB because I am gonna use the same code and will add some improvements in it. Moreover, if you are working on Live Videos instead of Images then you should have a look at Color Detection in Live Video using MATLAB.
For this purpose we need to ...
Hello friends, I hope you all are doing great. In today's tutorial, I am going to show you How to Convert m File into p File in MATLAB. Now the question arises that why we need to do that? & the answer is if you want to protect your code and don't want anyone to access it then you need to your Convert m File into p File. P File is like an encrypted file which performs the same functionality as your original m file but no one can get the code out of it.
Like me explain it with an example, suppose you are some sort of developer and you have created some code for a company and now you want to protect your code and just send the company some sort of software. MATLAB has a function in which you convert your m-file into p-file and no one can open ...
Hey Guys! Hope you are doing well. I am back to feed you with valuable information relating to engineering and technology. Today, I'll uncover the details on the Introduction to ATmega128. It is an AVR, 8-bit low power microcontroller, that comes with a 64-pin interface and is based on RISC architecture. Availability of 133 Powerful Instructions with single clock cycle and 32 x 8 General Purpose Working Registers make this device an ideal choice for many applications where decent code execution is required.
The memory space incorporates on this module is more than normal AVR controllers including Program memory around 128K, enough to store the number of instructions on a single chip.
In this post, I'll try to cover each and everything related t ...
