Hello friends, I hope you all are doing great. Today, I am going to share the Arduino WiFi Shield Library for Proteus . The Arduino WiFi Shield is the original Wi-Fi shield of Arduino: an HDG204 802.11 b/g module and an AT32UC3 processor that runs the shield's own firmware and TCP / IP stack, talking SPI to the Arduino through the WiFi library, with a micro SD socket on the same bus. Arduino has retired it, but the WiFi library and its examples are still in the Arduino IDE, and many projects and books were built on it. With this library you can place the shield in Proteus, stack your UNO beside it and run those sketches as they are. Updates Arduino WiFi Shield Library for Proteus Latest version: V1.0 (October 2026, this tutorial) Other Wi-Fi shields: AirLift WiFi Shield · WiFi Shield 101 E ...
Hello friends, I hope you all are doing great. Today, I am going to share the ATWINC1500 WiFi Breakout Library for Proteus . The ATWINC1500 breakout is a small board with Microchip's (Atmel's) ATWINC1500 Wi-Fi network controller that any microcontroller can use over SPI with the WiFi101 library. You choose its pins with WiFi.setPins() , and then WiFi.begin() , WiFiUDP , WiFiServer and the rest work as on a WiFi Shield 101. With this library you can place the breakout in Proteus, wire it to our Arduino Mega and run a WiFi101 sketch as it is. Updates ATWINC1500 WiFi Breakout Library for Proteus Latest version: V1.0 (October 2026, this tutorial) The same ATWINC1500 chip: WiFi Shield 101 ESP32 boards and modules: ESP32 DevKit V1 · ESP32-DevKitC V4 · ESP32-S3 DevKitC-1 · ESP32-C3 SuperMini · ES ...
Hello friends, I hope you all are doing great. Today, I am going to share the WiFi Shield 101 Library for Proteus . The WiFi Shield 101 is the Arduino shield with the ATWINC1500 Wi-Fi network controller from Microchip (Atmel before). Your Arduino keeps its own sketch and talks to the WINC1500 over SPI with the WiFi101 library: WiFi.begin() , WiFi.scanNetworks() , WiFi.ping() , WiFiServer , WiFiClient and the rest. With this library you can place the shield in Proteus, wire it to our Arduino Mega and run a WiFi101 sketch as it is. Updates WiFi Shield 101 Library for Proteus Latest version: V1.0 (October 2026, this tutorial) The same ATWINC1500 chip: ATWINC1500 WiFi Breakout Other Wi-Fi shields: AirLift WiFi Shield · Arduino WiFi Shield ESP32 boards and modules: ESP32 DevKit V1 · ESP32-DevKi ...
Hello friends, I hope you all are doing great. Today, I am going to share the AirLift ESP32 Breakout Library for Proteus . The AirLift breakout is a small board with an ESP32 Wi-Fi co-processor that any microcontroller can use over SPI . The ESP32 runs the NINA firmware , and your Arduino sketch talks to it with the WiFiNINA library: WiFi.begin() , WiFiClient , WiFiSSLClient , WiFi.getTime() and the rest. With this library you can place the breakout in Proteus, wire it to our UNO with six signal wires and run a WiFiNINA sketch as it is. Updates AirLift ESP32 Breakout Library for Proteus Latest version: V1.0 (October 2026, this tutorial) Other ESP32 boards and modules: ESP32 DevKit V1 · ESP32-DevKitC V4 · ESP32-S3 DevKitC-1 · ESP32-C3 SuperMini · ESP32-C6 DevKitC-1 · TTGO T-Display · T-Disp ...
Hello friends, I hope you all are doing great. Today, I am going to share the AirLift WiFi Shield Library for Proteus . The AirLift shield puts an ESP32 Wi-Fi co-processor on top of an Arduino UNO. The ESP32 runs the NINA firmware and the UNO talks to it over SPI with the WiFiNINA library - the same library the Arduino MKR WiFi 1010 and the UNO WiFi Rev2 use. Your sketch calls WiFi.begin() , WiFiServer and WiFiClient , and the ESP32 does the Wi-Fi, the TCP and UDP sockets and DNS. With this library you can place the shield in Proteus, wire it to our UNO and run a WiFiNINA sketch as it is. Updates AirLift WiFi Shield Library for Proteus Latest version: V1.0 (October 2026, this tutorial) Other Wi-Fi shields: WiFi Shield 101 · Arduino WiFi Shield Other ESP32 boards and modules: ESP32 DevKit V ...
Hello friends, I hope you all are doing great. Today, I am going to share the ESP32-WROOM-32 Library for Proteus . The ESP32-WROOM-32 is Espressif's best-known ESP32 module: the dual-core ESP32 chip, its flash and a PCB antenna under one metal shield, with 38 pins. Many people use it as a Wi-Fi modem for an Arduino : loaded with Espressif's ESP-AT firmware , it takes AT commands on a serial port, like an ESP-01. With this library you can place it in Proteus, wire it to an Arduino UNO and drive it with AT commands - join the Wi-Fi, open TCP connections, serve a page and even make HTTP requests with the module's own HTTP client. Updates ESP32-WROOM-32 Library for Proteus Latest version: V1.0 (October 2026, this tutorial) Other ESP32 boards and modules: ESP32 DevKit V1 · ESP32-DevKitC V4 · ES ...
Hello friends, I hope you all are doing great. Today, I am going to share the ESP-12F Library for Proteus . The ESP-12F is the successor of the famous ESP-12E: the same ESP8266 module with the same 22 pins and the same AT firmware, but with a reworked PCB antenna for a better signal. With this library you can place it in Proteus, wire it to an Arduino, send it AT commands and watch it join the Wi-Fi, switch its own blue LED and run a TCP server that several clients use at the same time - all inside the simulation. Updates ESP-12F Library for Proteus Latest version: V1.0 (October 2026, this tutorial) Other ESP8266 modules: ESP-01 · ESP-01S · ESP-07 · ESP-07S · ESP-12E · ESP-01 Adapter · WiFi Shield · NodeMCU · NodeMCU V2 · D1 Mini · D1 R2 ESP32 boards and modules: ESP32 DevKit V1 · ESP32-De ...
Hello friends, I hope you all are doing great. Today, I am going to share the ESP-12E Library for Proteus . The ESP-12E is the most popular ESP8266 module of all: it is the little shielded board inside most NodeMCU boards, with a PCB antenna printed at its top end, a blue LED on GPIO2 and 22 pins. With this library you can place it in Proteus on its own, wire it to an Arduino, send it AT commands and watch it join the Wi-Fi, serve a web page and a JSON reading, switch its own blue LED and talk UDP with other devices - all inside the simulation. Updates ESP-12E Library for Proteus Latest version: V1.0 (October 2026, this tutorial) Other ESP8266 modules: ESP-01 · ESP-01S · ESP-07 · ESP-07S · ESP-12F · ESP-01 Adapter · WiFi Shield · NodeMCU · NodeMCU V2 · D1 Mini · D1 R2 ESP32 boards and modu ...
Hello friends, I hope you all are doing great. Today, I am going to share the ESP-07S Library for Proteus . The ESP-07S is the shielded little brother of the ESP-07: a metal shield covers almost the whole board, there is no ceramic antenna at all, and the only way to the air is a u.FL socket for an external antenna. With this library you can place it in Proteus, wire it to an Arduino, send it AT commands and watch it join the Wi-Fi, serve a web page, switch an LED on its own GPIO pin and talk TCP with other devices - all inside the simulation. Updates ESP-07S Library for Proteus Latest version: V1.0 (October 2026, this tutorial) Other ESP8266 modules: ESP-01 · ESP-01S · ESP-07 · ESP-12E · ESP-12F · ESP-01 Adapter · WiFi Shield · NodeMCU · NodeMCU V2 · D1 Mini · D1 R2 ESP32 boards and modul ...
Hello friends, I hope you all are doing great. Today, I am going to share the Mobile WiFi Monitor Library for Proteus . When you finish a Wi-Fi project, the first thing you do is pick up your phone: you open the board's web page, tap a button and watch the LED. The Mobile WiFi Monitor puts that phone into Proteus. It is a smartphone - the TEP SmartPhone - that joins the Wi-Fi network of your simulation, with four apps: a Browser for the pages of your ESP32 and ESP8266 sketches, a Terminal for TCP and UDP, a Wi-Fi app and a Devices app with ping. Updates Mobile WiFi Monitor Library for Proteus Latest version: V1.0 (October 2026, this tutorial) ESP32 boards and modules: ESP32 DevKit V1 · ESP32-DevKitC V4 · ESP32-S3 DevKitC-1 · ESP32-C3 SuperMini · ESP32-C6 DevKitC-1 · TTGO T-Display · T-Disp ...
