TEP DOWNLOAD CENTER

Project Files of Anemometer Wind Speed Sensor Library for Proteus Simulation

Libraries Code Projects Simulation
tep://download-terminal 84e6ec6ea53c45028d782d2048394c11.zip ZIP archiveV1.0Verified0 downloadsFree
Anemometer Wind Speed Sensor Library for Proteus Simulation: an Arduino UNO V4.0 and the three-cup anemometer in a gale
Proteus library · File 1 of 1

Anemometer Wind Speed Sensor Library for Proteus V1.0

Anemometer Wind Speed Sensor Library for Proteus V1.0 comes as a ZIP archive of 10 files (1.2 MB, 2.6 MB unpacked) holding Proteus library files, simulation model DLLs, a Proteus simulation, an Arduino sketch and compiled HEX firmware.

  • LIBProteus library
  • DLLProteus model
  • DSNProteus simulation
  • INOArduino sketch
  • HEXHEX firmware

Description

Anemometer-Wind-Speed-Sensor-Library-for-Proteus-v1.0.zip with the anemometer for Proteus simulation (TEPANEMO.LIB and TEPANEMO.DLL), our Arduino UNO V4.0, the A4 demo with its sketch and a README.

Read Anemometer Wind Speed Sensor Library for Proteus Simulation

File Structure

84e6ec6ea53c45028d782d2048394c11.zip10 files · 5 folders · 2.6 MB unpacked
Anemometer-Wind-Speed-Sensor-TEP-v1.0/10 files · 2.6 MB
Arduino Code/1 file · 4.6 KB
Anemometer_Demo/1 file · 4.6 KB
INO Anemometer_Demo.inoArduino sketch 4.6 KB
Proteus Library Files/2 files · 217.7 KB
LIB ArduinoV4TEP.LIBProteus library 201.9 KB
LIB TEPANEMO.LIBProteus library 15.8 KB
Proteus Model Files/2 files · 1.2 MB
DLL TEPANEMO.DLLSimulation model 312.5 KB
DLL TEPARDUINO.DLLSimulation model 883.5 KB
Proteus Simulation/4 files · 1.2 MB
DSN Anemometer-Wind-Speed-Sensor-ArduinoUnoV4.pdsprjProteus simulation 18.8 KB
HEX Anemometer_Demo.hexCompiled HEX file 18.4 KB
DLL TEPANEMO.DLLSimulation model 312.5 KB
DLL TEPARDUINO.DLLSimulation model 883.5 KB
TXT README.txtText file 15.4 KB

README

README.txt 276 lines
ANEMOMETER WIND SPEED SENSOR LIBRARY FOR PROTEUS SIMULATION - V1.0 (three cups, a pulse output, a pop-up)
Designed by The Engineering Projects
www.TheEngineeringProjects.com

IMPORTANT LINKS
Article (read it first - pictures, step by step, every feature explained):
  https://www.theengineeringprojects.com/2026/11/anemometer-wind-speed-sensor-library-for-proteus.html
Report a bug or suggest a feature (our forum):
  https://www.theengineeringprojects.com/forum/category/motor-driver-proteus-library
The demo runs on our Arduino UNO V4.0 (included) - working LEDs, RESET and a
built-in serial monitor, no Virtual Terminal to wire - its own article:
  https://www.theengineeringprojects.com/2026/10/arduino-uno-library-for-proteus-v40.html
Support us (the libraries are free):
  https://www.theengineeringprojects.com/donate

FILE STRUCTURE
Anemometer-Wind-Speed-Sensor-TEP-v1.0/
|-- Proteus Library Files/
|   |-- ArduinoV4TEP.LIB                              201.9 KB   TEP Arduino boards V4.0 (UNO) -> LIBRARY
|   |-- TEPANEMO.LIB                                   15.8 KB   the library -> LIBRARY folder
|-- Proteus Model Files/
|   |-- TEPANEMO.DLL                                  312.5 KB   the model -> MODELS folder
|   |-- TEPARDUINO.DLL                                883.5 KB   the Arduino board model -> MODELS folder
|-- Proteus Simulation/
|   |-- Anemometer_Demo.hex                            18.4 KB   the demo firmware
|   |-- Anemometer-Wind-Speed-Sensor-ArduinoUnoV4.pdsprj   18.8 KB   the demo project
|   |-- TEPANEMO.DLL                                  312.5 KB   copy of the model
|   |-- TEPARDUINO.DLL                                883.5 KB   copy of the board model
|-- Arduino Code/
|   |-- Anemometer_Demo/Anemometer_Demo.ino             4.6 KB   the demo sketch (source of the .hex)
|-- README.txt                                        ~16.8 KB   this file
Total: 2.61 MB (unzipped). The C++ source code of the models is not included.

WHAT IS IT?
A three-cup anemometer with a pulse output - the black aluminium wind speed sensor of weather
stations, cranes and wind
turbines - drawn compact from the side (the three cups on their arms, the rotor head, the round body
with its label, the
mounting flange, the cable with three leads; our own drawing, no maker's mark). The real sensor is
about 180 mm across its
cups; the symbol is drawn at about a third of that, a little smaller than an Arduino UNO, so that it
fits any sheet. The
figures are from a maker's manual of such a sensor:
  * The supply: 5 to 24 V DC on VCC (brown) and GND (blue); the sensor takes 20 mA at 12 V.
  * The output: pulses on OUT (black). The pulse's high level is the supply voltage: feed the sensor
    from 5 V for a 5 V
    Arduino. Low, OUT is pulled to GND.
  * The maker's line: wind speed (m/s) = 0.5 + 0.169 x the pulses in one second. So 10 m/s give 56
    pulses a second, 30 m/s
    give 175, and under 0.5 m/s there are none. The cups start to turn at 0.2 m/s.
  * The cups follow the wind with a lag, shorter in a strong wind, and they slow down more slowly
    than they speed up.
  * The wind is the WIND property (m/s). PROFILE makes it STEADY, GUSTS (a gusty wind around WIND)
    or RISING (from calm
    to WIND in RAMP seconds); the pop-up's chips change the wind at Run.
  * On the sheet the label shows at Run the speed the sensor reports and the pulse frequency, and
    the wind's name on the
    Beaufort scale stands above the cups. Click it at Run for the pop-up: the cups turning seen from
    above, the pulses as
    on a scope, the maker's line worked out, the Beaufort scale, eight live values; graphs, an event
    log and a check page.
The body is drawn as on the real part and to true scale against our Arduino.
The TEP signature and the pop-up are TEP additions.

ONE DEVICE (search "WIND" or "ANEMOMETER" in Pick Devices):
  WINDSPEEDSENSORTEP  "Anemometer - Wind Speed Sensor with Pulse Output V1.0" in TEPANEMO.LIB
  (Transducers > Wind Speed),
                      prefix AN, model TEPANEMO.DLL (analog). Three pins under the flange: VCC
                      (brown, 5 - 24 V),
                      GND (blue), OUT (black, the pulses).

THE POP-UP
Click the part at Run. Tabs:
    Anemometer chips: the wind (Calm, Light 3, Breeze 8, Strong 14, Gale 20, Storm 30 m/s) and
    Gusts. The rotor seen from
               above, turning with the pulses, and the wind as streaks; the pulses on OUT as on a
               scope, with their
               frequency, their period and their high level; the maker's line worked out for the
               speed now; the
               Beaufort scale from 0 to 12 with the force now lit; eight live values: the wind in
               m/s and km/h, the
               speed the sensor shows, the pulses per second and their period, the cups' RPM, the
               Beaufort force and
               name, the supply's volts and milliamps, the pulses counted, the strongest wind so
               far.
    Graphs     the live values over the last 2, 6 or 15 s. Live / Freeze.
    Event log  every change and warning; filters All / Changes / Warnings, Pause, Clear
    Check      what the part is doing and what to look at, each with a verdict (green = fine, amber
    = check, red = wrong)
    Settings   theme, text size, open at Run, window size
    Help       report a bug, suggest a feature, article, updates, donate, forum; Copy diagnostics
    for a bug report

TEST STATUS
V1.0: verified in Proteus 8.5 on 16 Nov 2026 (the demo project as shipped: an A4 sheet, an Arduino UNO V4.0).
What the runs showed (the model's own numbers and the sketch's monitor):
The demo as shipped (Anemometer_Demo; AN1 WIND 30, PROFILE RISING, RAMP 4: the wind climbs from calm
to 30 m/s in 4 s;
VCC on 5 V, OUT on pin 2 of the UNO), one run (anfinal3), the model's pauses:
  * The cups start to turn at 0.030 s (the wind at 0.2 m/s); the first pulses at 0.418 s (the cups
    show 0.5 m/s).
  * 0.6 s, LIGHT AIR, force 1: the wind 4.5 m/s, the sensor shows 1.3 m/s, 4.9 pulses a second (one
    every 203.3 ms),
    37 RPM.
  * 1.2 s, MODERATE BREEZE, force 4: the wind 9.0 m/s, the sensor 6.3 m/s, 34.6 pulses a second, 259
    RPM.
  * 2.0 s, STRONG BREEZE, force 6: the wind 15.0 m/s, the sensor 13.6 m/s, 77.5 pulses a second, 582
    RPM.
  * GALE, force 8, at 2.439 s (17.2 m/s). At 2.75 s: the wind 20.6 m/s, the sensor 19.7 m/s, 113.5
    pulses a second
    (one every 8.8 ms), 851 RPM; on the sheet the label shows 19.7 m/s and 113 Hz, GALE 8 above the
    cups, and the
    UNO's LED 13 is lit.
  * STRONG GALE at 2.895 s, STORM at 3.369 s (3.4 s: the wind 25.5 m/s, the sensor 24.7 m/s, 143.5
    pulses a second,
    1076 RPM), VIOLENT STORM at 3.887 s.
  * 4.5 s, the wind steady at 30 m/s: VIOLENT STORM, force 11, the sensor shows 30.0 m/s, 174.5
    pulses a second (one
    every 5.7 ms), 1309 RPM: the cups have caught up.
  * In all: the strongest wind 30.0 m/s, the most the sensor showed 30.0 m/s, at most 174.5 pulses a
    second, 394
    pulses counted; 5.00 V and 8.3 mA on the supply.
  * The monitor (a line every 500 ms): calm twice, then 5.2 m/s (28 Hz, force 3), 10.4, 14.8, 18.8
    m/s (109 Hz, force
    8, GALE WARNING), 22.8, 26.7 and 29.9 m/s (174 Hz, force 11). 89 s for the 4.5 s of the run.
A second run in a gusty wind (angust2: PROFILE GUSTS, WIND 10): at 2.0 s the wind has dropped to 6.9
m/s while the
sensor still shows 9.4 m/s (52.9 pulses a second, 397 RPM): the cups slow down more slowly than they
speed up.
A third run in a wind of 0.4 m/s (anlight2: PROFILE STEADY, WIND 0.4): the cups creep (under 1 RPM),
no pulses, the
sensor shows 0.0 m/s, CALM.

INSTALLATION (about 2 minutes)
1. Close Proteus. Extract the WHOLE ZIP to a normal folder (e.g. Desktop).
2. Copy everything in "Proteus Library Files" (TEPANEMO.LIB and our Arduino library V4.0,
ArduinoV4TEP.LIB, with the ARDUINO UNO V4.0 used by the demo) to the LIBRARY folder of Proteus, for
example:
     C:\Program Files (x86)\Labcenter Electronics\Proteus 8 Professional\LIBRARY
   (use the folder that already holds Proteus's own .LIB files).
3. Copy TEPANEMO.DLL and TEPARDUINO.DLL from "Proteus Model Files" to the MODELS folder (...\Proteus
8 Professional\MODELS).
4. Delete TEPANEMO.IDX from the LIBRARY folder if it is there (Proteus makes a new index).
5. Start Proteus. In Pick Devices (P) search "WIND".

RUN THE DEMO
"Proteus Simulation\Anemometer-Wind-Speed-Sensor-ArduinoUnoV4.pdsprj" (an A4 sheet) - keep the .hex
file and the DLLs beside the project.
  A wind speed monitor with a gale warning:
  ARD1:   Arduino UNO V4.0 running Anemometer_Demo.hex, its serial monitor built in (window "TEP
  Arduino UNO - ARD1").
  AN1:    the anemometer: VCC on 5 V, GND on ground, OUT to pin 2 over the label WIND. Its wind
  rises from calm to
          30 m/s in 4 seconds (WIND 30, PROFILE RISING, RAMP 4), to show the whole scale in one
          short run.
          The sketch times the pulses with an interrupt, works out the pulses per second and from
          them the wind speed,
          prints it in m/s and km/h with the Beaufort force and name, and lights the UNO's LED from
          force 8, a gale.
Closed the monitor? Click the UNO's USB port.

WIRING (the same in Proteus and on a real board)
  VCC (brown) to 5 V, GND (blue) to ground, OUT (black) to an interrupt pin (pin 2 or 3 of an UNO).
  Fed from 5 V the
  pulses are 5 V high. Fed from 12 or 24 V they are 12 or 24 V high: divide them down (10 k and 6.8
  k for 12 V) or use an
  optocoupler before an Arduino pin.
REAL HARDWARE:
 * Mount the sensor level, in free air, well above roofs and trees: a sheltered anemometer reads
   low.
 * A long cable picks up noise: use a shielded cable, and a small capacitor (10 nF) from the input
   pin to ground.
 * The makers sell the same sensor with other outputs (4 - 20 mA, RS485, 0 - 5 V) and other lines:
   check the label and the
   manual of yours, and change OFFSET and SLOPE in the sketch.
 * Bearings wear and cups collect dirt and ice: a real sensor is checked against a reference from
   time to time.

THE DEMO SKETCH ON THE SERIAL MONITOR (Anemometer_Demo V1.0, 9600 baud)
The sketch reports every 500 ms. Type a command:
  max        the strongest wind so far       reset      forget it       rate 1000      report every
  1000 ms       help
EXPECTED MONITOR OUTPUT
  Wind speed monitor - The Engineering Projects
  Speed = 0.5 + 0.169 x pulses per second. Gale warning (LED 13) from 17.2 m/s.
  Commands: max | reset | rate 500 | help
  Wind 0.0 m/s  0 km/h  0 Hz  force 0  calm
  Wind 0.0 m/s  0 km/h  0 Hz  force 0  calm
  Wind 5.2 m/s  19 km/h  28 Hz  force 3  gentle breeze
  Wind 10.4 m/s  38 km/h  59 Hz  force 5  fresh breeze
  Wind 14.8 m/s  53 km/h  84 Hz  force 7  near gale
  Wind 18.8 m/s  68 km/h  109 Hz  force 8  gale  GALE WARNING
  Wind 22.8 m/s  82 km/h  132 Hz  force 9  strong gale  GALE WARNING
  Wind 26.7 m/s  96 km/h  155 Hz  force 10  storm  GALE WARNING
  Wind 29.9 m/s  108 km/h  174 Hz  force 11  violent storm  GALE WARNING

PROPERTIES (double-click the part > Edit Properties)
  Wind speed (WIND)                    m/s, 0 - 60 (5)
  The wind over time (PROFILE)         STEADY, GUSTS (a gusty wind around WIND) or RISING (from calm
  to WIND) (STEADY)
  RISING's time (RAMP)                 the seconds from calm to WIND, 0.5 - 60 (4)
Every run starts again from the properties.

LINKS.INI (OPTIONAL)
The Help page cards of the pop-up open web pages. To point them somewhere else without a new DLL,
put a text file named links.ini next to TEPANEMO.DLL with lines KEY=URL, for example:
  ARTICLE=https://www.theengineeringprojects.com/...
Keys: WEBSITE, FORUM, BUG_REPORT, FEATURE_REQUEST, ARTICLE, USER_GUIDE,
UPDATE_CHECK, DONATE. Only http:// and https:// links are used; lines starting
with # are comments.

TROUBLESHOOTING
* NO SUPPLY on the label: under 4.5 V between VCC and GND. The sensor needs 5 to 24 V.
* No pulses although the cups turn: the wind is under 0.5 m/s, where the maker's line gives no
  pulses.
* The Arduino reads 0: OUT is not on an interrupt pin, or the sensor's GND is not joined to the
  Arduino's GND.
* The reading jumps at very low wind: there are only a few pulses a second; the sketch needs two of
  them for a value.
* The speed is too high by a constant factor: your sensor has another line. Change SLOPE and OFFSET
  in the sketch.
* The part is not simulated: TEPANEMO.DLL is missing from MODELS and from the project folder.
* The part is not simulated: TEPANEMO.DLL is missing from MODELS and from the project folder. No UNO
  / no monitor window: TEPARDUINO.DLL is missing, or click the UNO's USB port.

BUG REPORTS AND FEATURE REQUESTS
Please post them in our forum with a screenshot, the Serial Monitor text, the
simulation log and the pop-up's Copy diagnostics text:
  https://www.theengineeringprojects.com/forum/category/motor-driver-proteus-library

SUPPORT US
This library is free. If it saves you time, please support our work:
  https://www.theengineeringprojects.com/donate

WEBSITE
  https://www.theengineeringprojects.com/

LICENCES AND THIRD-PARTY NOTES
* The model (TEPANEMO.DLL), the symbols and artwork, the other parts of ours in the demo and the
  Arduino Library V4.0 (ArduinoV4TEP.LIB / TEPARDUINO.DLL, with its built-in TEP Serial Monitor
  Advance) are made by The Engineering Projects. The models use only standard Windows libraries; no
  Visual C++ redistributable is needed.
  The C++ source code is not included.
* Arduino UNO V4.0 (ArduinoV4TEP.LIB / TEPARDUINO.DLL, our Arduino Library V4.0 - its
  microcontroller is Proteus's own AVR model): The Engineering Projects,
  https://www.theengineeringprojects.com/2026/10/arduino-uno-library-for-proteus-v40.html
* The .hex file is built from the demo sketch and the Arduino AVR core 1.8.6, which includes
  LGPL-licensed code; its source code is available at
  https://github.com/arduino/ArduinoCore-avr/tree/1.8.6
* Proteus is a product of Labcenter Electronics and is not included. Arduino is a trademark of Arduino SA.
  This library is not made or endorsed by Arduino or Labcenter.

REBUILDING THE FIRMWARE (OPTIONAL)
The HEX file is supplied; Arduino IDE is not needed to run the demo. To edit the sketch, open
Arduino Code\Anemometer_Demo\Anemometer_Demo.ino, select Arduino Uno and use Sketch > Export
Compiled Binary. Replace the simulation's .hex with the exported HEX. The sketch needs 6,684 bytes
of flash and 366 bytes of RAM.

MODEL SCOPE AND LIMITS
Modelled: the wind (steady, gusts, rising); the cups' lag (a distance constant of 2.5 m - ours - and
a slower fall) and
their starting threshold; the pulses by the maker's line, half of each pulse high; the output stage
(1 k to VCC when
high, 100 ohm to GND when low - ours); the supply current (VCC / 600 ohm: 20 mA at 12 V); the least
supply (4.5 V - ours).
For the picture of the rotor and the RPM we took eight pulses a turn (ours: the manual does not
say). The symbol is drawn at
0.36 of the real size. Not modelled: the
sensor's accuracy band (+-(0.3 + 0.03 V) m/s), the bearings' friction with temperature, icing, the
wind's direction, the
other outputs of the sensor family (4 - 20 mA, RS485).

VERSION
TEP Anemometer library V1.0 (Nov 2026). Device WINDSPEEDSENSORTEP (TEPANEMO.LIB / TEPANEMO.DLL).
Demo sketch Anemometer_Demo V1.0 (an interrupt on pin 2, no library). Demo board: ARDUINO UNO V4.0
(TEP Arduino Library V4.0) with its built-in serial monitor.
Advertisement

Development1 release

  1. V1.0Anemometer Wind Speed Sensor Library for Proteus V1.0this page

    V1.0 is the only release in the Download Center so far. When a newer version is published, it appears above with its own download page.

Installation8 steps

From the download to a working project, in order. The steps follow what the package contains.

You will need

  • Proteus Design SuiteProteus 8 or newer (Labcenter), on Windows
  • Arduino IDE1.8 or 2.x, with the board of the tutorial chosen under Tools → Board
  • Any archive toolWindows, macOS and Linux extract ZIP files on their own

Steps

  1. 1

    Extract the archive

    Right-click 84e6ec6ea53c45028d782d2048394c11.zip and choose Extract All (or open it with 7-Zip or WinRAR) into a folder you can find again. Keep its folder structure (Anemometer-Wind-Speed-Sensor-TEP-v1.0) as it is.

  2. 2

    Copy the library files into Proteus

    Move ArduinoV4TEP.LIB and TEPANEMO.LIB and the files into the LIBRARY folder of your Proteus installation: C:\Program Files (x86)\Labcenter Electronics\Proteus 8 Professional\LIBRARY for Proteus 8, or the matching Proteus 7 folder. Older versions keep it under ProgramData\Labcenter Electronics. If Proteus is open, close it first.

  3. 3

    Add the simulation model

    Copy TEPANEMO.DLL and TEPARDUINO.DLL into the MODELS folder next to LIBRARY, so the component can run, not only be drawn.

  4. 4

    Restart Proteus and place the component

    Start Proteus, open a schematic, press P (Pick Devices) and search for the component by the name used in the tutorial. It appears with its pins ready to wire.

  5. 5

    Open the sketch in the Arduino IDE

    Open Anemometer_Demo.ino, select your board and port under Tools, then Verify. Sketch → Export Compiled Binary writes the HEX file a simulation needs.

  6. 6

    Load the HEX file

    In Proteus double-click the microcontroller, set Program File to Anemometer_Demo.hex and run the simulation. For real hardware, flash the same file with your programmer.

  7. 7

    Open the example simulation

    Open Anemometer-Wind-Speed-Sensor-ArduinoUnoV4.pdsprj in Proteus to see the wiring exactly as in the tutorial. Check the controller's Program File path, then press Play.

  8. 8

    Follow the tutorial

    Anemometer Wind Speed Sensor Library for Proteus Simulation explains every connection and setting in order; keep it open beside the files while you build.

How to add a library in Proteus 8

FAQs9 questionsContact TEP

How do I download Anemometer Wind Speed Sensor Library for Proteus V1.0?

Wait for the 30-second guest countdown on this page, then press the download button; the file comes straight from our storage. Members who are logged in skip the wait. If the browser opens the file instead of saving it, use its Save as option. The download link is made for you when the countdown ends and works for 15 minutes; a saved or shared link stops working, so share this page instead.

What is inside the archive?

Anemometer Wind Speed Sensor Library for Proteus V1.0 comes as a ZIP archive of 10 files (1.2 MB, 2.6 MB unpacked) holding Proteus library files, simulation model DLLs, a Proteus simulation, an Arduino sketch and compiled HEX firmware. Open the File Structure tab for the full list of 10 files.

What should I do if the download does not start?

Check the browser's download list first; an ad blocker or a company firewall can also hold it back, so try another browser or network. If the file arrives incomplete, download it again. For an installation problem, read the Install tab or tell us in the comments with your software version and the exact error message.

Is this file free?

Yes. Every file in the TEP Download Center is free for learning, personal and student projects. If you share it, link back to this page or the tutorial so others find the latest version.

How do I check that the file arrived complete?

Compare its SHA-256 with the one on this page, 54c9ae50488605431aa6a3cac2401d5ea6615bd92ad861d8d1300a66bc227a7f. In PowerShell run Get-FileHash "84e6ec6ea53c45028d782d2048394c11.zip"; on macOS or Linux run shasum -a 256 "84e6ec6ea53c45028d782d2048394c11.zip". The same value means the file is exactly the one in our storage; a different one means the download broke off, so download it again.

Do I need WinRAR to open the ZIP file?

No. Windows, macOS and Linux open ZIP archives on their own (Extract All, or double-click). WinRAR and 7-Zip work too. Extract the whole archive before using the files.

Where do I put the LIB and IDX files?

Both files go into the LIBRARY folder of your Proteus installation (Proteus 8: C:\Program Files (x86)\Labcenter Electronics\Proteus 8 Professional\LIBRARY; Proteus 7 has the same folder under its own name). Restart Proteus afterwards and search for the component with P.

Which Proteus version does the library need?

The tutorial names the Proteus version the library was made and tested with. Most TEP libraries work in Proteus 7 and Proteus 8; if the component does not appear after a restart, check that both the LIB and the IDX file were copied and that Proteus was fully closed while copying.

How do I get the HEX file into the simulation?

Compile the sketch in the Arduino IDE (Sketch → Export Compiled Binary gives you the HEX next to the sketch), then in Proteus double-click the board, set Program File to that HEX and run.

preparing · 84e6ec6ea53c45028d782d2048394c11.zip
Rating
Your download will be ready shortly
Preparing your download…

Members skip the wait. Log in or join TEP.

  • 0Total downloads
  • 4%Popularity
  • ProteusCategory
  • 0Comments
  • ssyedzainnasirUploaded by
  • 16 Nov 2026Uploaded at
Last 14 days0 downloads
SHA-256 54c9ae50488605431aa6a3cac2401d5ea6615bd92ad861d8d1300a66bc227a7f
DocumentationAnemometer Wind Speed Sensor Library for Proteus Simulation
Need help with this file? Bug report Ask a question Download problemsGet updates
Advertisement

Comments

0

Join the conversation

Start the conversationAsk a question or share how you used this download.