Project Files of Wind Turbine Charge Controller Library for Proteus Simulation
08562c2640bf47c78174c6cf81d5efb3.zip

Wind Turbine Charge Controller Library for Proteus V1.0
Wind Turbine Charge Controller Library for Proteus V1.0 comes as a ZIP archive of 19 files (2.2 MB, 4.5 MB unpacked) holding Proteus library files, simulation model DLLs, a Proteus simulation, an Arduino sketch and compiled HEX firmware.
- LIBProteus library
- DLLProteus model
- DSNProteus simulation
- INOArduino sketch
- HEXHEX firmware
Description
Wind-Turbine-Charge-Controller-Library-for-Proteus-v1.0.zip with the wind charge controller for Proteus simulation (TEPWINDCC.LIB and TEPWINDCC.DLL), our wind turbine, our 3-phase generator, our lead-acid battery, our Arduino UNO V4.0, the A3 demo with its sketch and a README.
File Structure
5.9 KB201.9 KB16.2 KB22.6 KB31.1 KB16 KB883.5 KB325 KB292.5 KB299.5 KB327.5 KB883.5 KB325 KB292.5 KB299.5 KB327.5 KB27.9 KB27.1 KB19.1 KBGallery12 images from the tutorialOpen the tutorial
The circuit, the board and the results as they appear in Wind Turbine Charge Controller Library for Proteus Simulation. Open an image for its full size.












README
WIND TURBINE CHARGE CONTROLLER LIBRARY FOR PROTEUS SIMULATION - V1.0 (12 V / 24 V, a dump load, a brake, a pop-up)
Designed by The Engineering Projects
www.TheEngineeringProjects.com
IMPORTANT LINKS
Article (read it first - pictures, step by step, every feature explained):
https://www.theengineeringprojects.com/2026/11/wind-turbine-charge-controller-library-for-proteus.html
Report a bug or suggest a feature (our forum):
https://www.theengineeringprojects.com/forum/category/motor-driver-proteus-library
The demo runs on our Arduino UNO V4.0 (included) - working LEDs, RESET and a
built-in serial monitor, no Virtual Terminal to wire - its own article:
https://www.theengineeringprojects.com/2026/10/arduino-uno-library-for-proteus-v40.html
The demo measures the battery with our INA219 library (installed from its own package - not in this zip):
https://www.theengineeringprojects.com/2026/10/ina219-current-sensor-library-for-proteus-v1-0.html
The demo's turbine is our Vertical-Axis Wind Turbine library (its LIB and DLL are in this zip; its own article):
https://www.theengineeringprojects.com/2026/11/vertical-axis-wind-turbine-library-for-proteus-v1-0.html
The demo's generator is our 3-Phase PM Generator library (its LIB and DLL are in this zip; its own article):
https://www.theengineeringprojects.com/2026/11/3-phase-pm-generator-library-for-proteus-v1-0.html
The demo's battery is our 12V Lead-Acid Battery library (its LIB and DLL are in this zip; its own article):
https://www.theengineeringprojects.com/2026/11/12v-lead-acid-battery-library-for-proteus.html
Support us (the libraries are free):
https://www.theengineeringprojects.com/donate
FILE STRUCTURE
Wind-Turbine-Charge-Controller-TEP-v1.0/
|-- Proteus Library Files/
| |-- ArduinoV4TEP.LIB 201.9 KB TEP Arduino boards V4.0 (UNO) -> LIBRARY
| |-- TEPLEADACID.LIB 16.2 KB a part the demo uses -> LIBRARY folder
| |-- TEPPMGEN.LIB 22.6 KB a part the demo uses -> LIBRARY folder
| |-- TEPVAWT.LIB 31.1 KB a part the demo uses -> LIBRARY folder
| |-- TEPWINDCC.LIB 16.0 KB the library -> LIBRARY folder
|-- Proteus Model Files/
| |-- TEPARDUINO.DLL 883.5 KB the Arduino board model -> MODELS folder
| |-- TEPLEADACID.DLL 325.0 KB its model -> MODELS folder
| |-- TEPPMGEN.DLL 292.5 KB its model -> MODELS folder
| |-- TEPVAWT.DLL 299.5 KB its model -> MODELS folder
| |-- TEPWINDCC.DLL 327.5 KB the model -> MODELS folder
|-- Proteus Simulation/
| |-- TEPARDUINO.DLL 883.5 KB copy of the board model
| |-- TEPLEADACID.DLL 325.0 KB copy of its model
| |-- TEPPMGEN.DLL 292.5 KB copy of its model
| |-- TEPVAWT.DLL 299.5 KB copy of its model
| |-- TEPWINDCC.DLL 327.5 KB copy of the model
| |-- WindCharge_Demo.hex 27.1 KB the demo firmware
| |-- Wind-Charge-Controller-Turbine-Battery-INA219-ArduinoUnoV4.pdsprj 27.9 KB the demo project
|-- Arduino Code/
| |-- WindCharge_Demo/WindCharge_Demo.ino 5.9 KB the demo sketch (source of the .hex)
|-- README.txt ~19.6 KB this file
Total: 4.52 MB (unzipped). The C++ source code of the models is not included.
WHAT IS IT?
A compact waterproof wind turbine charge controller with a dump load output - 12 V / 24 V, a blue
finned aluminium case
of 100 x 87 mm with four lamps - drawn at true scale (the case, the label plate with the BATTERY,
WIND, DUMP and BRAKE lamps,
seven leads; our own drawing, no maker's mark). The figures are from makers' manuals of such
controllers:
* The rectifier: the three wires of a wind generator (U V W, in any order) are turned into DC by
six diodes and charge
the battery. The generator charges whenever its voltage is above the battery's; nothing flows
back.
* A wind generator must never run without a load: unloaded it races. So a full battery is not
simply disconnected.
From 13.5 V the controller pulses a DUMP LOAD (a power resistor on DUMP+ / DUMP-), 500 times a
second; the pulses
widen as the battery's voltage rises, up to always on at 14.5 V. The surplus of the wind becomes
heat and the rotor
keeps its load.
* The BRAKE: if the battery still reaches 14.5 V (no dump load, or one too small), or the
generator gives more than
15 A, the controller shorts the three wires. The generator then works against its own windings
and the rotor slows
down. The brake lets go when the battery is back at 13.5 V, at the earliest after five minutes.
* STOP in the pop-up is the manual brake switch, for maintenance or a storm.
* Under 8 V on the battery the controller is off: connect the battery first. 24 V doubles the
battery voltages.
* On the sheet the four lamps work at Run (the WIND lamp flashes with the generator's frequency)
and the label plate
shows the state, the generator's frequency and current and the battery's volts and amps. Click
it at Run for the
pop-up: the power flow, the dump load's pulses, the voltage band, eight live values; graphs, an
event log and a check
page.
The body is drawn as on the real part and to true scale against our Arduino.
The TEP signature and the pop-up are TEP additions.
ONE DEVICE (search "WINDCHARGE" in Pick Devices):
WINDCHARGECONTROLLERTEP "Wind Turbine Charge Controller 12 V / 24 V with Dump Load V1.0" in
TEPWINDCC.LIB
(Electromechanical > Charge Controllers), prefix CC, model TEPWINDCC.DLL
(analog). Seven pins along
the bottom, at the ends of the leads: U V W (the generator), BAT+ BAT-
(the battery), DUMP+ DUMP-
(the dump load). The name starts with W so that it sorts after the
embedded ARDUINO UNO V4.0.
THE POP-UP
Click the part at Run. Tabs:
Controller chips: the dump load by PWM or off; STOP (the manual brake); the clock (x 1, x 60, x
3600). The power flow from
the rotor through the rectifier to the battery, with the dump load as a branch under
the DC line and the
brake as a red bar; the dump load's pulses over three periods; the battery's voltage
on a band with the
13.5 V and 14.5 V marks; the three states with the one now lit; eight live values:
the generator's
frequency and voltage, the rectified current, the battery voltage, the charge
current, the dump load's on
time and mean current, its heat, the brake, the amp-hours and watt-hours.
Graphs the live values over the last 2, 6 or 15 s. Live / Freeze.
Event log every change and warning; filters All / Changes / Warnings, Pause, Clear
Check what the part is doing and what to look at, each with a verdict (green = fine, amber
= check, red = wrong)
Settings theme, text size, open at Run, window size
Help report a bug, suggest a feature, article, updates, donate, forum; Copy diagnostics
for a bug report
TEST STATUS
V1.0: verified in Proteus 8.5 on 16 Nov 2026 (the demo project as shipped: an A3 sheet, an Arduino UNO V4.0).
What the runs showed (the model's own numbers and the sketch's monitor):
The demo as shipped (WindCharge_Demo; WT1 our vertical-axis wind turbine WIND 11 m/s, GEN1 our
3-phase PM generator on
its shaft, CC1 a 12 V system with the dump load on PWM, R1 3.3 ohm as the dump load, BAT1 our
lead-acid battery SOC 85
%, the INA219 between BAT+ and the battery, SPEED 3600 on the battery and the controller), one run
(wcfinal4), the
model's pauses:
* NO WIND while the rotor spins up: at 0.6 s the generator at 37 Hz gives 7.3 V between two wires,
the battery at
12.70 V.
* CHARGING at 0.862 s: the generator's voltage has passed the battery's.
* DUMP LOAD at 1.182 s: the battery has reached 13.5 V. At 1.2 s 0.84 A from the generator (61
Hz), the battery at
13.47 V takes 0.82 A, the first pulses (4 %). At 2.0 s 1.39 A from the generator (65 Hz, 11.9
V), the battery at
13.72 V takes 0.46 A, the dump load on for 23 % of the time, 0.91 A mean (12.5 W).
* At 2.0 s the other pop-ups: the turbine 652 RPM, 24.16 W on the shaft (the best 25.34 W at 615
RPM); the generator
11.80 V rms, 65.2 Hz, 1.127 A rms, 21.41 W, 87 % of its rated current; the battery 0.45 A in at
13.68 V, 93 %; the
INA219 (U1) 13.672 V on the bus, 43.20 mV on the shunt, 432.0 mA (one reading in the pulses'
ripple).
* A steady state: at 3.6 s 1.42 A from the generator, 0.14 A into the battery at 13.81 V, the dump
load 31 %, 1.26 A
mean, 17.5 W. At 4.35 s 32 %, 1.33 A mean, 18.3 W; the battery at 13.82 V takes 0.07 A.
* In all 62.5 Wh from the wind: 1.12 Ah into the battery, 46.0 Wh into the dump load; the battery
between 12.70 V
and 13.85 V; the most current 1.43 A; the fastest 66 Hz; the brake never came on.
* The monitor: 0 RPM (the rotor stands), 382 RPM (turning, no charge), 603 RPM 13.46 V +0.75 A
(charging), from 647
RPM and 13.61 V the dump load works, the charge current falls to +0.07 A at 13.81 V; it ended at
+1.07 Ah. 116 s
for the 4.3 s of the run.
A second run without a dump load (wcbrake4: DUMP OFF): CHARGING with 1.02 A at 13.90 V and 64 Hz
(1.4 s); BRAKE at
1.624 s (the battery reached 14.51 V), let go at 1.708 s (13.45 V); BRAKE again at 2.214 s and 2.938
s, three in all;
at 3.05 s, braked, 55 Hz and 0.2 V between two wires, the battery at 14.15 V; after each brake NO
WIND until the rotor
is fast again.
A third run in a light wind (wclight3: WIND 6): at 1.6 s 27 Hz and 5.4 V between two wires, the
battery at 12.69 V: NO
WIND.
INSTALLATION (about 2 minutes)
1. Close Proteus. Extract the WHOLE ZIP to a normal folder (e.g. Desktop).
2. Copy everything in "Proteus Library Files" (TEPWINDCC.LIB, TEPVAWT.LIB, TEPPMGEN.LIB,
TEPLEADACID.LIB and our Arduino library V4.0, ArduinoV4TEP.LIB, with the ARDUINO UNO V4.0 used by
the demo) to the LIBRARY folder of Proteus, for example:
C:\Program Files (x86)\Labcenter Electronics\Proteus 8 Professional\LIBRARY
(use the folder that already holds Proteus's own .LIB files).
3. Copy TEPWINDCC.DLL, TEPVAWT.DLL, TEPPMGEN.DLL, TEPLEADACID.DLL and TEPARDUINO.DLL from "Proteus
Model Files" to the MODELS folder (...\Proteus 8 Professional\MODELS).
4. Delete TEPWINDCC.IDX from the LIBRARY folder if it is there (Proteus makes a new index).
5. Start Proteus. In Pick Devices (P) search "WINDCHARGE".
RUN THE DEMO
"Proteus Simulation\Wind-Charge-Controller-Turbine-Battery-INA219-ArduinoUnoV4.pdsprj" (an A3 sheet)
- keep the .hex file and the DLLs beside the project.
A small wind power system:
ARD1: Arduino UNO V4.0 running WindCharge_Demo.hex, its serial monitor built in (window "TEP
Arduino UNO - ARD1").
WT1: our Vertical-Axis Wind Turbine, WIND 11 m/s; its SHAFT pin turns the generator.
GEN1: our 3-Phase PM Generator, DRIVE=SHAFT; its U V W go to the controller over the labels U V
W.
CC1: the wind charge controller: 12 V, dump load by PWM, SPEED 3600; BAT- on ground.
R1: 3.3 ohm on DUMP+ / DUMP-: the dump load (a power resistor of 100 W in real life).
U1: our INA219 (its pop-up version) between the controller's BAT+ (VIN+) and the battery's +
(VIN-); SDA A4, SCL A5.
BAT1: our 12 V 7.2 Ah lead-acid battery, SOC 85 %, SPEED 3600 (an hour each simulated second), -
on ground.
R2: 100 k from the generator's wire U to the Arduino's pin 2: the speed.
The sketch takes 32 readings and works with their mean, times the generator's cycles on
pin 2 for its RPM, tells
the state from the battery's side and counts the amp-hours; the UNO's LED lights while the
battery is charged.
Closed the monitor? Click the UNO's USB port.
WIRING (the same in Proteus and on a real board)
Connect the battery first (BAT+ / BAT-), then the generator's three wires (U V W, in any order),
then the dump load
on DUMP+ / DUMP-. DUMP+ is joined to BAT+ inside; the controller switches DUMP-. The battery's -
is the ground of the
system; the generator's three wires have no ground of their own.
REAL HARDWARE:
* Size the dump load for ALL the generator can give: 300 W at 14 V is about 21 A, a resistor of 0.6
ohm or less, and it
must be able to stay at that power for hours. Mount it in free air, away from anything that
burns.
* Put a fuse or breaker in the battery lead, never between the generator and the controller.
* A manual brake switch that shorts the three wires belongs beside the controller: use it before
any work on the system.
* The Arduino's pin 2 sees one of the generator's wires through 100 k; on a real board add a clamp
or an optocoupler.
THE DEMO SKETCH ON THE SERIAL MONITOR (WindCharge_Demo V1.0, 9600 baud)
The sketch reports every 500 ms. Type a command:
reset the counter back to 0 rate 1000 report every 1000 ms help
EXPECTED MONITOR OUTPUT
Wind battery monitor - The Engineering Projects
+ A: into the battery. Clock x 3600: a simulated second is an hour.
Commands: reset | rate 500 | help
Generator 0 RPM 12.71 V +0.01 A the rotor stands +0.00 Ah
Generator 382 RPM 12.70 V -0.02 A turning, no charge -0.01 Ah
Generator 603 RPM 13.46 V +0.75 A charging +0.13 Ah
Generator 647 RPM 13.61 V +0.60 A charging, the dump load works +0.40 Ah
Generator 653 RPM 13.71 V +0.38 A charging, the dump load works +0.69 Ah
Generator 655 RPM 13.74 V +0.27 A charging, the dump load works +0.82 Ah
Generator 656 RPM 13.78 V +0.17 A charging, the dump load works +0.95 Ah
Generator 657 RPM 13.80 V +0.12 A charging, the dump load works +1.01 Ah
Generator 655 RPM 13.81 V +0.07 A charging, the dump load works +1.07 Ah
PROPERTIES (double-click the part > Edit Properties)
System voltage (SYSTEM) 12 or 24; 24 doubles every battery voltage (12)
Dump load (DUMP) PWM (stepless, from 13.5 V) or OFF (no dump load: the brake
alone) (PWM)
Clock (SPEED) 1 real time, 3600 an hour each simulated second - the same as
the battery's, 1 - 7200 (1)
Every run starts again from the properties.
LINKS.INI (OPTIONAL)
The Help page cards of the pop-up open web pages. To point them somewhere else without a new DLL,
put a text file named links.ini next to TEPWINDCC.DLL with lines KEY=URL, for example:
ARTICLE=https://www.theengineeringprojects.com/...
Keys: WEBSITE, FORUM, BUG_REPORT, FEATURE_REQUEST, ARTICLE, USER_GUIDE,
UPDATE_CHECK, DONATE. Only http:// and https:// links are used; lines starting
with # are comments.
TROUBLESHOOTING
* NO BATTERY: under 8 V on BAT+ / BAT-. The controller is powered by the battery: connect it first.
* NO WIND although the rotor turns: the generator's voltage is still under the battery's. A wind
generator charges only
above a certain speed; more wind, or a generator with more volts for each turn, is needed.
* The dump load takes no current: nothing is on DUMP+ / DUMP-, or DUMP is OFF. The battery then
rises to 14.5 V and the
brake comes on, again and again.
* BRAKE all the time: the STOP chip is on; or the dump load is too small for this wind; or over 15 A
came from the generator.
* The battery never reaches 13.5 V: the battery's clock runs in real time - set SPEED as the
battery's (60 or 3600).
* The part is not simulated: TEPWINDCC.DLL is missing from MODELS and from the project folder. No
UNO / no monitor window: TEPARDUINO.DLL is missing, or click the UNO's USB port.
BUG REPORTS AND FEATURE REQUESTS
Please post them in our forum with a screenshot, the Serial Monitor text, the
simulation log and the pop-up's Copy diagnostics text:
https://www.theengineeringprojects.com/forum/category/motor-driver-proteus-library
SUPPORT US
This library is free. If it saves you time, please support our work:
https://www.theengineeringprojects.com/donate
WEBSITE
https://www.theengineeringprojects.com/
LICENCES AND THIRD-PARTY NOTES
* The model (TEPWINDCC.DLL), the symbols and artwork, the other parts of ours in the demo and the
Arduino Library V4.0 (ArduinoV4TEP.LIB / TEPARDUINO.DLL, with its built-in TEP Serial Monitor
Advance) are made by The Engineering Projects. The models use only standard Windows libraries; no
Visual C++ redistributable is needed.
The C++ source code is not included.
* Arduino UNO V4.0 (ArduinoV4TEP.LIB / TEPARDUINO.DLL, our Arduino Library V4.0 - its
microcontroller is Proteus's own AVR model): The Engineering Projects,
https://www.theengineeringprojects.com/2026/10/arduino-uno-library-for-proteus-v40.html
* The .hex file is built from the demo sketch and the Arduino AVR core 1.8.6, which includes
LGPL-licensed code; its source code is available at
https://github.com/arduino/ArduinoCore-avr/tree/1.8.6
* Proteus is a product of Labcenter Electronics and is not included. Arduino is a trademark of Arduino SA.
This library is not made or endorsed by Arduino or Labcenter.
REBUILDING THE FIRMWARE (OPTIONAL)
The HEX file is supplied; Arduino IDE is not needed to run the demo. To edit the sketch, open
Arduino Code\WindCharge_Demo\WindCharge_Demo.ino, select Arduino Uno and use Sketch > Export
Compiled Binary. Replace the simulation's .hex with the exported HEX. The sketch needs 9,854 bytes
of flash and 542 bytes of RAM.
MODEL SCOPE AND LIMITS
Modelled: the six rectifier diodes (0.8 V at 1 A); the dump load's switch with real pulses at 500
Hz, their width in
proportion to the battery's voltage between 13.5 V and 14.5 V; the brake that shorts the three wires
at 14.5 V or over 15 A
and lets go at 13.5 V after five minutes; the STOP switch; the 8 V the controller needs; its own 20
mA; the four lamps;
24 V systems; SPEED; a 47 mF capacitor at the battery terminals for the smoothing a real battery
gives. Not modelled: a solar input, the controller's heat and its fuse, reverse-polarity protection,
the
display of larger controllers. The pulse rate, the linear widening, the brake's five minutes and its
50 mohm are ours; the
dump load output follows other makers' controllers of this kind (the compact one drawn here brakes
only).
VERSION
TEP Wind Charge Controller library V1.0 (Nov 2026). Device WINDCHARGECONTROLLERTEP (TEPWINDCC.LIB /
TEPWINDCC.DLL). Demo sketch WindCharge_Demo V1.0 (the INA219 read straight with Wire). The demo also
uses our Vertical-Axis Wind Turbine (TEPVAWT: VAWTTEP), our 3-Phase PM Generator (TEPPMGEN:
PMGENTEP) and our 12V Lead-Acid Battery (TEPLEADACID: LEADACIDBAT12V7TEP), shipped in this package.
Demo board: ARDUINO UNO V4.0 (TEP Arduino Library V4.0) with its built-in serial monitor.Development1 release
-
V1.0Wind Turbine Charge Controller Library for Proteus V1.0this page
V1.0 is the only release in the Download Center so far. When a newer version is published, it appears above with its own download page.
Installation8 steps
From the download to a working project, in order. The steps follow what the package contains.
You will need
- Proteus Design SuiteProteus 8 or newer (Labcenter), on Windows
- Arduino IDE1.8 or 2.x, with the board of the tutorial chosen under Tools → Board
- Any archive toolWindows, macOS and Linux extract ZIP files on their own
Steps
- 1
Extract the archive
Right-click 08562c2640bf47c78174c6cf81d5efb3.zip and choose Extract All (or open it with 7-Zip or WinRAR) into a folder you can find again. Keep its folder structure (Wind-Turbine-Charge-Controller-TEP-v1.0) as it is.
- 2
Copy the library files into Proteus
Move ArduinoV4TEP.LIB, TEPLEADACID.LIB and TEPPMGEN.LIB and 2 more and the files into the LIBRARY folder of your Proteus installation: C:\Program Files (x86)\Labcenter Electronics\Proteus 8 Professional\LIBRARY for Proteus 8, or the matching Proteus 7 folder. Older versions keep it under ProgramData\Labcenter Electronics. If Proteus is open, close it first.
- 3
Add the simulation model
Copy TEPARDUINO.DLL, TEPLEADACID.DLL and TEPPMGEN.DLL and 2 more into the MODELS folder next to LIBRARY, so the component can run, not only be drawn.
- 4
Restart Proteus and place the component
Start Proteus, open a schematic, press P (Pick Devices) and search for the component by the name used in the tutorial. It appears with its pins ready to wire.
- 5
Open the sketch in the Arduino IDE
Open WindCharge_Demo.ino, select your board and port under Tools, then Verify. Sketch → Export Compiled Binary writes the HEX file a simulation needs.
- 6
Load the HEX file
In Proteus double-click the microcontroller, set Program File to WindCharge_Demo.hex and run the simulation. For real hardware, flash the same file with your programmer.
- 7
Open the example simulation
Open Wind-Charge-Controller-Turbine-Battery-INA219-ArduinoUnoV4.pdsprj in Proteus to see the wiring exactly as in the tutorial. Check the controller's Program File path, then press Play.
- 8
Follow the tutorial
Wind Turbine Charge Controller Library for Proteus Simulation explains every connection and setting in order; keep it open beside the files while you build.
FAQs9 questionsContact TEP
How do I download Wind Turbine Charge Controller Library for Proteus V1.0?
Wait for the 30-second guest countdown on this page, then press the download button; the file comes straight from our storage. Members who are logged in skip the wait. If the browser opens the file instead of saving it, use its Save as option. The download link is made for you when the countdown ends and works for 15 minutes; a saved or shared link stops working, so share this page instead.
What is inside the archive?
Wind Turbine Charge Controller Library for Proteus V1.0 comes as a ZIP archive of 19 files (2.2 MB, 4.5 MB unpacked) holding Proteus library files, simulation model DLLs, a Proteus simulation, an Arduino sketch and compiled HEX firmware. Open the File Structure tab for the full list of 19 files.
What should I do if the download does not start?
Check the browser's download list first; an ad blocker or a company firewall can also hold it back, so try another browser or network. If the file arrives incomplete, download it again. For an installation problem, read the Install tab or tell us in the comments with your software version and the exact error message.
Is this file free?
Yes. Every file in the TEP Download Center is free for learning, personal and student projects. If you share it, link back to this page or the tutorial so others find the latest version.
How do I check that the file arrived complete?
Compare its SHA-256 with the one on this page, c60f7b34230772cb6f9de006714423d38a83d1bac5e7b3f132aa709a319c2248. In PowerShell run Get-FileHash "08562c2640bf47c78174c6cf81d5efb3.zip"; on macOS or Linux run shasum -a 256 "08562c2640bf47c78174c6cf81d5efb3.zip". The same value means the file is exactly the one in our storage; a different one means the download broke off, so download it again.
Do I need WinRAR to open the ZIP file?
No. Windows, macOS and Linux open ZIP archives on their own (Extract All, or double-click). WinRAR and 7-Zip work too. Extract the whole archive before using the files.
Where do I put the LIB and IDX files?
Both files go into the LIBRARY folder of your Proteus installation (Proteus 8: C:\Program Files (x86)\Labcenter Electronics\Proteus 8 Professional\LIBRARY; Proteus 7 has the same folder under its own name). Restart Proteus afterwards and search for the component with P.
Which Proteus version does the library need?
The tutorial names the Proteus version the library was made and tested with. Most TEP libraries work in Proteus 7 and Proteus 8; if the component does not appear after a restart, check that both the LIB and the IDX file were copied and that Proteus was fully closed while copying.
How do I get the HEX file into the simulation?
Compile the sketch in the Arduino IDE (Sketch → Export Compiled Binary gives you the HEX next to the sketch), then in Proteus double-click the board, set Program File to that HEX and run.
Members skip the wait. Log in or join TEP.
- 0Total downloads
- 4%Popularity
- ProteusCategory
- 0Comments
- ssyedzainnasirUploaded by
- 16 Nov 2026Uploaded at
c60f7b34230772cb6f9de006714423d38a83d1bac5e7b3f132aa709a319c2248
















Comments
0