TEP DOWNLOAD CENTER

Project Files of TP4056 Li-ion Charger Module Library for Proteus Simulation

Libraries Code Projects Simulation
tep://download-terminal 9016bd215872427092f01f1b9e8a3ada.zip ZIP archiveV1.0Verified0 downloadsFree
TP4056 Li-ion Charger Module Library for Proteus Simulation: an Arduino UNO V4.0, the TP4056 module, our INA219 and an 18650 cell
Proteus library · File 1 of 1

TP4056 Li-ion Charger Module Library for Proteus V1.0

TP4056 Li-ion Charger Module Library for Proteus V1.0 comes as a ZIP archive of 16 files (1.9 MB, 3.9 MB unpacked) holding Proteus library files, simulation model DLLs, a Proteus simulation, an Arduino sketch and compiled HEX firmware.

  • LIBProteus library
  • DLLProteus model
  • DSNProteus simulation
  • INOArduino sketch
  • HEXHEX firmware

Description

TP4056-Li-ion-Charger-Module-Library-for-Proteus-v1.0.zip with the TP4056 charger module for Proteus simulation (TEPTP4056.LIB and TEPTP4056.DLL), our 18650 Li-ion cell, our N-MOSFET, our Arduino UNO V4.0, the A4 demo with its sketch and a README.

Read TP4056 Li-ion Charger Module Library for Proteus Simulation

File Structure

9016bd215872427092f01f1b9e8a3ada.zip16 files · 5 folders · 3.9 MB unpacked
TP4056-Li-ion-Charger-Module-TEP-v1.0/16 files · 3.9 MB
Arduino Code/1 file · 6 KB
Tp4056Charge_Demo/1 file · 6 KB
INO Tp4056Charge_Demo.inoArduino sketch 6 KB
Proteus Library Files/4 files · 247.7 KB
LIB ArduinoV4TEP.LIBProteus library 201.9 KB
LIB TEP18650.LIBProteus library 11.9 KB
LIB TEPNMOS.LIBProteus library 17.9 KB
LIB TEPTP4056.LIBProteus library 16 KB
Proteus Model Files/4 files · 1.8 MB
DLL TEP18650.DLLSimulation model 319.5 KB
DLL TEPARDUINO.DLLSimulation model 883.5 KB
DLL TEPNMOS.DLLSimulation model 295 KB
DLL TEPTP4056.DLLSimulation model 330.5 KB
Proteus Simulation/6 files · 1.8 MB
DLL TEP18650.DLLSimulation model 319.5 KB
DLL TEPARDUINO.DLLSimulation model 883.5 KB
DLL TEPNMOS.DLLSimulation model 295 KB
DLL TEPTP4056.DLLSimulation model 330.5 KB
DSN TP4056-Charger-18650-INA219-ArduinoUnoV4.pdsprjProteus simulation 23.7 KB
HEX Tp4056Charge_Demo.hexCompiled HEX file 27.2 KB
TXT README.txtText file 17.8 KB

README

README.txt 300 lines
TP4056 LI-ION CHARGER MODULE LIBRARY FOR PROTEUS SIMULATION - V1.0 (1 A, with protection, two lamps and a pop-up)
Designed by The Engineering Projects
www.TheEngineeringProjects.com

IMPORTANT LINKS
Article (read it first - pictures, step by step, every feature explained):
  https://www.theengineeringprojects.com/2026/11/tp4056-li-ion-charger-module-library-for-proteus.html
Report a bug or suggest a feature (our forum):
  https://www.theengineeringprojects.com/forum/category/motor-driver-proteus-library
The demo runs on our Arduino UNO V4.0 (included) - working LEDs, RESET and a
built-in serial monitor, no Virtual Terminal to wire - its own article:
  https://www.theengineeringprojects.com/2026/10/arduino-uno-library-for-proteus-v40.html
The demo measures the cell with our INA219 library (installed from its own package - not in this zip):
  https://www.theengineeringprojects.com/2026/10/ina219-current-sensor-library-for-proteus-v1-0.html
The demo's cell is our 18650 Li-ion Battery library (its LIB and DLL are in this zip; its own article):
  https://www.theengineeringprojects.com/2026/11/18650-li-ion-battery-library-for-proteus.html
The demo's load switch is our N-MOSFET library's IRLZ44N (its LIB and DLL are in this zip; its own article):
  https://www.theengineeringprojects.com/2026/11/n-mosfet-library-for-proteus.html
Support us (the libraries are free):
  https://www.theengineeringprojects.com/donate

FILE STRUCTURE
TP4056-Li-ion-Charger-Module-TEP-v1.0/
|-- Proteus Library Files/
|   |-- ArduinoV4TEP.LIB                              201.9 KB   TEP Arduino boards V4.0 (UNO) -> LIBRARY
|   |-- TEP18650.LIB                                   11.9 KB   a part the demo uses -> LIBRARY folder
|   |-- TEPNMOS.LIB                                    17.9 KB   a part the demo uses -> LIBRARY folder
|   |-- TEPTP4056.LIB                                  16.0 KB   the library -> LIBRARY folder
|-- Proteus Model Files/
|   |-- TEP18650.DLL                                  319.5 KB   its model -> MODELS folder
|   |-- TEPARDUINO.DLL                                883.5 KB   the Arduino board model -> MODELS folder
|   |-- TEPNMOS.DLL                                   295.0 KB   its model -> MODELS folder
|   |-- TEPTP4056.DLL                                 330.5 KB   the model -> MODELS folder
|-- Proteus Simulation/
|   |-- TEP18650.DLL                                  319.5 KB   copy of its model
|   |-- TEPARDUINO.DLL                                883.5 KB   copy of the board model
|   |-- TEPNMOS.DLL                                   295.0 KB   copy of its model
|   |-- TEPTP4056.DLL                                 330.5 KB   copy of the model
|   |-- Tp4056Charge_Demo.hex                          27.2 KB   the demo firmware
|   |-- TP4056-Charger-18650-INA219-ArduinoUnoV4.pdsprj   23.7 KB   the demo project
|-- Arduino Code/
|   |-- Tp4056Charge_Demo/Tp4056Charge_Demo.ino         6.0 KB   the demo sketch (source of the .hex)
|-- README.txt                                        ~18.6 KB   this file
Total: 3.89 MB (unzipped). The C++ source code of the models is not included.

WHAT IS IT?
The small blue TP4056 lithium-ion charger module with protection - 26 x 17 mm, a USB socket, 1 A -
drawn at true scale
(the socket, the charger chip, the protection chip with its dual MOSFET, the two lamps, the RPROG
resistor and the six pads;
our own drawing, no maker's mark). The figures are from the chips' data sheets:
  * A linear charger for ONE lithium-ion cell: constant current first (1000 mA with RPROG 1.2 k),
    then a constant 4.2 V
    while the current falls, and the end when the current is a tenth of the set current. The blue
    lamp then shows a full
    cell. A new charge starts by itself when the cell falls under 4.05 V.
  * A deeply discharged cell, under 2.9 V, gets a tenth of the current (TRICKLE) until it is back
    over 2.9 V.
  * The input: 5 V on IN+ / IN- (the USB socket's pads). The charger works from 3.8 V and only while
    the input is above the
    cell; without an input it sleeps and takes nothing from the cell. A weak supply shows: the input
    falls to just above
    the cell and the current is less than set.
  * The heat: a linear charger turns (input - cell) x current into heat. The model follows the
    chip's temperature; at
    135 C the current is cut back, as the real chip does with a low cell or a high input voltage.
  * The protection (the second chip and its two MOSFETs) guards the load on OUT+ / OUT-: the output
    is cut when the cell is
    under 2.4 V (back at 3.0 V) and when more than about 3 A flow (back when the load is removed).
  * The pads: IN- and B- are joined inside, OUT+ is B+, OUT- comes from B- through the protection's
    switch.
  * On the sheet the two lamps work at Run (red: charging, blue: full); the stage is written above
    the module, the charge
    current and the cell's voltage under it. Click it at Run for the pop-up: the power flow, the
    charge so far (current
    and voltage against time), the stages, eight live values; graphs, an event log and a check page.
The body is drawn as on the real part and to true scale against our Arduino.
The TEP signature and the pop-up are TEP additions.

ONE DEVICE (search "TP4056CHARGER" in Pick Devices):
  TP4056CHARGERTEP  "TP4056 Li-ion Charger Module 1 A with Protection V1.0" in TEPTP4056.LIB
  (Electromechanical > Charge
                    Controllers), prefix CH, model TEPTP4056.DLL (analog). Six pins: IN+ and IN- on
                    the left beside the USB
                    socket; OUT+ B+ B- OUT- on the right, from top to bottom.

THE POP-UP
Click the part at Run. Tabs:
    Charger    chips: the charge current (1000, 580, 250, 130 mA = RPROG 1.2, 2, 5, 10 k); the clock
    (x 1, x 60, x 3600). The
               power flow from the supply through the charger chip to the cell and the protected
               output, with the heat
               and the chip's temperature; the charge so far - the current (orange) and the cell's
               voltage (green) against
               the time; the four stages with the one now lit; eight live values: the input's volts
               and milliamps, the
               charge current against the set one, the cell's voltage, the chip's temperature and
               heat, the output, the
               milliamp-hours into the cell side and to the output, the time on charge, the lamps.
    Graphs     the live values over the last 2, 6 or 15 s. Live / Freeze.
    Event log  every change and warning; filters All / Changes / Warnings, Pause, Clear
    Check      what the part is doing and what to look at, each with a verdict (green = fine, amber
    = check, red = wrong)
    Settings   theme, text size, open at Run, window size
    Help       report a bug, suggest a feature, article, updates, donate, forum; Copy diagnostics
    for a bug report

TEST STATUS
V1.0: verified in Proteus 8.5 on 16 Nov 2026 (the demo project as shipped: an A4 sheet, an Arduino UNO V4.0).
What the runs showed (the model's own numbers and the sketch's monitor):
The demo as shipped (Tp4056Charge_Demo; CH1 RPROG 1.2 k, BAT1 our 18650 cell SOC 10 %, 5 V over R2
0.2 ohm, the INA219 between
B+ and the cell, SPEED 3600 on the cell and the module), one run (tpfinal2), the model's own pauses:
  * CONSTANT CURRENT from the start (the cell at 3.60 V): at 0.3 s 1000 mA into the cell side, the
    pad at 3.93 V, the input
    at 4.80 V (the cable's drop), 0.86 W of heat, the chip at 81 C. At 1.0 s the cell's pop-up: 1.00
    A in at 3.96 V, 48 %;
    the INA219 (U1): 3.964 V on the bus, 99.99 mV on the shunt, 999.9 mA.
  * CONSTANT VOLTAGE at 1.599 s, after 1598 mAh: the pad held at 4.2 V; 960 mA at 1.7 s, 431 mA at
    2.2 s (the chip at 44 C),
    134 mA at 2.8 s.
  * CHARGE COMPLETE at 2.976 s: the current fell under 100 mA - 2174 mAh in 2 h 58 min; the blue
    lamp; the cell settles at
    4.14 V, the input back at 5.00 V, 2 mA from the supply.
  * In all 2174 mAh into the cell side; the cell between 3.82 V and 4.20 V; the most current 1000
    mA; the chip's hottest
    moment 87 C; the input between 4.80 V and 5.00 V.
  * The monitor: constant current with +1000 mA, constant voltage from 4.10 V while the current fell
    to +112 mA, charge
    complete at 4.14 V; it ended at +1947 mAh and 2 h 42 min (the Arduino starts a quarter of a
    second - a quarter of an
    hour of the cell's time - after the simulation). 115 s for the 3.9 s of the run.
A second run without an input (tpcut1: R2 on ground, SOC 5 %): NO INPUT, the Arduino switches the
load on; 0.31 A from the
cell at 3.08 V (0.45 s); OVER-DISCHARGE at 0.697 s with the cell at 2.40 V - the output is off; the
cell back at 2.61 V.
A third run (tpover1: no input, SOC 80 %, a load of 0.5 ohm): OVER-CURRENT at 0.174 s, 5.7 A - the
output is off and stays off.
A fourth run (tphot2: SOC 0 %, TEMP 60): THERMAL LIMIT at the start, 1.8 V across the chip, the
current cut back to 636 mA;
three minutes later (0.06 s) 910 mA with the chip at 119 C; the full 1000 mA from then on.

INSTALLATION (about 2 minutes)
1. Close Proteus. Extract the WHOLE ZIP to a normal folder (e.g. Desktop).
2. Copy everything in "Proteus Library Files" (TEPTP4056.LIB, TEP18650.LIB, TEPNMOS.LIB and our
Arduino library V4.0, ArduinoV4TEP.LIB, with the ARDUINO UNO V4.0 used by the demo) to the LIBRARY
folder of Proteus, for example:
     C:\Program Files (x86)\Labcenter Electronics\Proteus 8 Professional\LIBRARY
   (use the folder that already holds Proteus's own .LIB files).
3. Copy TEPTP4056.DLL, TEP18650.DLL, TEPNMOS.DLL and TEPARDUINO.DLL from "Proteus Model Files" to
the MODELS folder (...\Proteus 8 Professional\MODELS).
4. Delete TEPTP4056.IDX from the LIBRARY folder if it is there (Proteus makes a new index).
5. Start Proteus. In Pick Devices (P) search "TP4056CHARGER".

RUN THE DEMO
"Proteus Simulation\TP4056-Charger-18650-INA219-ArduinoUnoV4.pdsprj" (an A4 sheet) - keep the .hex
file and the DLLs beside the project.
  A single-cell charger with a charge monitor:
  ARD1:   Arduino UNO V4.0 running Tp4056Charge_Demo.hex, its serial monitor built in (window "TEP
  Arduino UNO - ARD1").
  CH1:    the TP4056 charger module: RPROG 1.2 k (1000 mA), SPEED 3600. IN+ on the net USB, IN- and
  B- on ground.
  R2:     0.2 ohm from the 5 V supply to the net USB: the USB cable.
  U1:     our INA219 (its pop-up version) between the module's B+ (VIN+) and the cell's + (VIN-);
  SDA A4, SCL A5.
  BAT1:   our 18650 lithium-ion cell, SOC 10 %, SPEED 3600 (an hour each simulated second), - on
  ground.
  R1, Q1: a 10 ohm load on OUT+ and our IRLZ44N MOSFET to OUT-, its gate on D7. D2 watches the net
  USB: the sketch lets
          the load run only while the charger has no input (never charge and feed a load at the same
          time).
          The sketch takes eight readings and works with their mean, tells the stage from the cell's
          voltage and current,
          and counts the milliamp-hours and the time on charge; the UNO's LED lights while the cell
          is charged.
Closed the monitor? Click the UNO's USB port.

WIRING (the same in Proteus and on a real board)
  5 V on IN+ / IN- (in real life the module's USB socket and a charger that can give 1 A - not the
  Arduino's 5 V pin).
  ONE lithium-ion cell on B+ / B-. The load on OUT+ / OUT-, never straight on the cell, so that the
  protection can guard
  it. IN- and B- are the module's ground; OUT- is NOT the same point (the protection's switch is in
  between).
REAL HARDWARE:
 * Set the current for the cell: at most the cell's capacity in an hour, less for a longer life. The
   module ships with
   RPROG 1.2 k (1000 mA): too much for a small 200 mAh cell - change the resistor (2 k: 580 mA, 5 k:
   250 mA, 10 k: 130 mA).
 * Do not run a load while charging: the charger ends the charge by the current, and a load's
   current hides the cell's.
 * The chip gets hot at 1 A, most of all with a low cell. That is normal; it cuts the current back
   by itself.
 * One cell only, or cells in parallel. Never cells in series, and never a cell of another
   chemistry.

THE DEMO SKETCH ON THE SERIAL MONITOR (Tp4056Charge_Demo V1.0, 9600 baud)
The sketch reports every 300 ms. Type a command:
  reset      the counters back to 0       rate 500       report every 500 ms       help
EXPECTED MONITOR OUTPUT
  Li-ion charge monitor - The Engineering Projects
  + mA: into the cell, - mA: out of it. Clock x 3600: a simulated second is an hour.
  Commands: reset | rate 300 | help
  The charger has its input: the load stays OFF
  Cell 3.82 V  +1000 mA  constant current  +0 mAh  0 h 00 min
  Cell 3.88 V  +1000 mA  constant current  +264 mAh  0 h 15 min
  ...
  Cell 4.10 V  +901 mA  constant voltage  +1459 mAh  1 h 27 min
  Cell 4.13 V  +631 mA  constant voltage  +1687 mAh  1 h 45 min
  ...
  Cell 4.14 V  +0 mA  charge complete  +1947 mAh  2 h 42 min

PROPERTIES (double-click the part > Edit Properties)
  Charge current resistor (RPROG)      in k: 1.2 = 1000 mA, 2 = 580 mA, 3 = 400 mA, 5 = 250 mA, 10 =
  130 mA; 1.2 - 10 (1.2)
  Clock (SPEED)                        1 real time, 3600 an hour each simulated second - the same as
  the battery's, 1 - 7200 (1)
  Air temperature (TEMP)               around the module, C: the chip's heat adds to it; -20 - 60
  (25)
Every run starts again from the properties.

LINKS.INI (OPTIONAL)
The Help page cards of the pop-up open web pages. To point them somewhere else without a new DLL,
put a text file named links.ini next to TEPTP4056.DLL with lines KEY=URL, for example:
  ARTICLE=https://www.theengineeringprojects.com/...
Keys: WEBSITE, FORUM, BUG_REPORT, FEATURE_REQUEST, ARTICLE, USER_GUIDE,
UPDATE_CHECK, DONATE. Only http:// and https:// links are used; lines starting
with # are comments.

TROUBLESHOOTING
* NO INPUT although 5 V is connected: IN+ is under 3.8 V at the module, or not above the cell. Check
  the supply and the
  cable; a thin cable loses a few tenths of a volt at 1 A.
* The current is less than set: the chip is at its thermal limit (a low cell or a high input), or
  the supply is weak and
  IN+ has fallen to just above the cell. The pop-up says which.
* The charge never ends: a load takes its current while charging. Switch the load off, or feed it
  from the supply.
* The output is off: the cell fell under 2.4 V (it comes back at 3.0 V - charge the cell), or more
  than about 3 A flowed
  (remove the load).
* NO BATTERY: nothing is on B+ / B-. The module holds 4.2 V on the open pad.
* The charge takes hours in real time: set SPEED as the battery's (60 or 3600).
* The part is not simulated: TEPTP4056.DLL is missing from MODELS and from the project folder. No
  UNO / no monitor window: TEPARDUINO.DLL is missing, or click the UNO's USB port.

BUG REPORTS AND FEATURE REQUESTS
Please post them in our forum with a screenshot, the Serial Monitor text, the
simulation log and the pop-up's Copy diagnostics text:
  https://www.theengineeringprojects.com/forum/category/motor-driver-proteus-library

SUPPORT US
This library is free. If it saves you time, please support our work:
  https://www.theengineeringprojects.com/donate

WEBSITE
  https://www.theengineeringprojects.com/

LICENCES AND THIRD-PARTY NOTES
* The model (TEPTP4056.DLL), the symbols and artwork, the other parts of ours in the demo and the
  Arduino Library V4.0 (ArduinoV4TEP.LIB / TEPARDUINO.DLL, with its built-in TEP Serial Monitor
  Advance) are made by The Engineering Projects. The models use only standard Windows libraries; no
  Visual C++ redistributable is needed.
  The C++ source code is not included.
* Arduino UNO V4.0 (ArduinoV4TEP.LIB / TEPARDUINO.DLL, our Arduino Library V4.0 - its
  microcontroller is Proteus's own AVR model): The Engineering Projects,
  https://www.theengineeringprojects.com/2026/10/arduino-uno-library-for-proteus-v40.html
* The .hex file is built from the demo sketch and the Arduino AVR core 1.8.6, which includes
  LGPL-licensed code; its source code is available at
  https://github.com/arduino/ArduinoCore-avr/tree/1.8.6
* Proteus is a product of Labcenter Electronics and is not included. Arduino is a trademark of Arduino SA.
  This library is not made or endorsed by Arduino or Labcenter.

REBUILDING THE FIRMWARE (OPTIONAL)
The HEX file is supplied; Arduino IDE is not needed to run the demo. To edit the sketch, open
Arduino Code\Tp4056Charge_Demo\Tp4056Charge_Demo.ino, select Arduino Uno and use Sketch > Export
Compiled Binary. Replace the simulation's .hex with the exported HEX. The sketch needs 9,890 bytes
of flash and 510 bytes of RAM.

MODEL SCOPE AND LIMITS
Modelled: the charger as one element between IN+ and B+ that gives the least of the set current, the
current that holds the
pad at 4.2 V and what the input can push through the pass transistor (0.4 ohm fully on - ours);
trickle under 2.9 V, the end
at a tenth of the set current, recharge under 4.05 V; the 3.8 V lockout and the input-above-the-cell
rule; the chip's heat
(65 C/W - ours) and the cut-back at 135 C; the lamps; the protection's over-discharge (2.4 V / 3.0
V), over-current
(150 mV across a 50 mohm switch - about 3 A), short-circuit and over-charge levels with their
delays; SPEED.
Not modelled: the chip's TEMP pin (the module ties it to ground), the CE pin, the soft start,
reverse-polarity damage, a
cell's own protection board, the 10 uF capacitors, the USB data lines.

VERSION
TEP TP4056 Li-ion Charger Module library V1.0 (Nov 2026). Device TP4056CHARGERTEP (TEPTP4056.LIB /
TEPTP4056.DLL). Demo sketch Tp4056Charge_Demo V1.0 (the INA219 read straight with Wire). The demo
also uses our 18650 Li-ion Battery (TEP18650: LIION18650TEP) and our N-MOSFET library (TEPNMOS:
IRLZ44NTEP), shipped in this package. Demo board: ARDUINO UNO V4.0 (TEP Arduino Library V4.0) with
its built-in serial monitor.
Advertisement

Development1 release

  1. V1.0TP4056 Li-ion Charger Module Library for Proteus V1.0this page

    V1.0 is the only release in the Download Center so far. When a newer version is published, it appears above with its own download page.

Installation8 steps

From the download to a working project, in order. The steps follow what the package contains.

You will need

  • Proteus Design SuiteProteus 8 or newer (Labcenter), on Windows
  • Arduino IDE1.8 or 2.x, with the board of the tutorial chosen under Tools → Board
  • Any archive toolWindows, macOS and Linux extract ZIP files on their own

Steps

  1. 1

    Extract the archive

    Right-click 9016bd215872427092f01f1b9e8a3ada.zip and choose Extract All (or open it with 7-Zip or WinRAR) into a folder you can find again. Keep its folder structure (TP4056-Li-ion-Charger-Module-TEP-v1.0) as it is.

  2. 2

    Copy the library files into Proteus

    Move ArduinoV4TEP.LIB, TEP18650.LIB and TEPNMOS.LIB and 1 more and the files into the LIBRARY folder of your Proteus installation: C:\Program Files (x86)\Labcenter Electronics\Proteus 8 Professional\LIBRARY for Proteus 8, or the matching Proteus 7 folder. Older versions keep it under ProgramData\Labcenter Electronics. If Proteus is open, close it first.

  3. 3

    Add the simulation model

    Copy TEP18650.DLL, TEPARDUINO.DLL and TEPNMOS.DLL and 1 more into the MODELS folder next to LIBRARY, so the component can run, not only be drawn.

  4. 4

    Restart Proteus and place the component

    Start Proteus, open a schematic, press P (Pick Devices) and search for the component by the name used in the tutorial. It appears with its pins ready to wire.

  5. 5

    Open the sketch in the Arduino IDE

    Open Tp4056Charge_Demo.ino, select your board and port under Tools, then Verify. Sketch → Export Compiled Binary writes the HEX file a simulation needs.

  6. 6

    Load the HEX file

    In Proteus double-click the microcontroller, set Program File to Tp4056Charge_Demo.hex and run the simulation. For real hardware, flash the same file with your programmer.

  7. 7

    Open the example simulation

    Open TP4056-Charger-18650-INA219-ArduinoUnoV4.pdsprj in Proteus to see the wiring exactly as in the tutorial. Check the controller's Program File path, then press Play.

  8. 8

    Follow the tutorial

    TP4056 Li-ion Charger Module Library for Proteus Simulation explains every connection and setting in order; keep it open beside the files while you build.

How to add a library in Proteus 8

FAQs9 questionsContact TEP

How do I download TP4056 Li-ion Charger Module Library for Proteus V1.0?

Wait for the 30-second guest countdown on this page, then press the download button; the file comes straight from our storage. Members who are logged in skip the wait. If the browser opens the file instead of saving it, use its Save as option. The download link is made for you when the countdown ends and works for 15 minutes; a saved or shared link stops working, so share this page instead.

What is inside the archive?

TP4056 Li-ion Charger Module Library for Proteus V1.0 comes as a ZIP archive of 16 files (1.9 MB, 3.9 MB unpacked) holding Proteus library files, simulation model DLLs, a Proteus simulation, an Arduino sketch and compiled HEX firmware. Open the File Structure tab for the full list of 16 files.

What should I do if the download does not start?

Check the browser's download list first; an ad blocker or a company firewall can also hold it back, so try another browser or network. If the file arrives incomplete, download it again. For an installation problem, read the Install tab or tell us in the comments with your software version and the exact error message.

Is this file free?

Yes. Every file in the TEP Download Center is free for learning, personal and student projects. If you share it, link back to this page or the tutorial so others find the latest version.

How do I check that the file arrived complete?

Compare its SHA-256 with the one on this page, 3fd640e5bd45fd00a087d6f4d3638ebb79e33ebf2d29012ab67eadfc0c6a56fe. In PowerShell run Get-FileHash "9016bd215872427092f01f1b9e8a3ada.zip"; on macOS or Linux run shasum -a 256 "9016bd215872427092f01f1b9e8a3ada.zip". The same value means the file is exactly the one in our storage; a different one means the download broke off, so download it again.

Do I need WinRAR to open the ZIP file?

No. Windows, macOS and Linux open ZIP archives on their own (Extract All, or double-click). WinRAR and 7-Zip work too. Extract the whole archive before using the files.

Where do I put the LIB and IDX files?

Both files go into the LIBRARY folder of your Proteus installation (Proteus 8: C:\Program Files (x86)\Labcenter Electronics\Proteus 8 Professional\LIBRARY; Proteus 7 has the same folder under its own name). Restart Proteus afterwards and search for the component with P.

Which Proteus version does the library need?

The tutorial names the Proteus version the library was made and tested with. Most TEP libraries work in Proteus 7 and Proteus 8; if the component does not appear after a restart, check that both the LIB and the IDX file were copied and that Proteus was fully closed while copying.

How do I get the HEX file into the simulation?

Compile the sketch in the Arduino IDE (Sketch → Export Compiled Binary gives you the HEX next to the sketch), then in Proteus double-click the board, set Program File to that HEX and run.

preparing · 9016bd215872427092f01f1b9e8a3ada.zip
Rating
Your download will be ready shortly
Preparing your download…

Members skip the wait. Log in or join TEP.

  • 0Total downloads
  • 4%Popularity
  • ProteusCategory
  • 0Comments
  • ssyedzainnasirUploaded by
  • 16 Nov 2026Uploaded at
Last 14 days0 downloads
SHA-256 3fd640e5bd45fd00a087d6f4d3638ebb79e33ebf2d29012ab67eadfc0c6a56fe
DocumentationTP4056 Li-ion Charger Module Library for Proteus Simulation
Need help with this file? Bug report Ask a question Download problemsGet updates
Advertisement

Comments

0

Join the conversation

Start the conversationAsk a question or share how you used this download.