Project Files of 12V to 230V Pure Sine Wave Inverter Library for Proteus Simulation
ac1174eaab904127a8a30f534e659a26.zip

12V to 230V Pure Sine Wave Inverter Library for Proteus V1.0
12V to 230V Pure Sine Wave Inverter Library for Proteus V1.0 comes as a ZIP archive of 13 files (1.5 MB, 3.3 MB unpacked) holding Proteus library files, simulation model DLLs, a Proteus simulation, an Arduino sketch and compiled HEX firmware.
- LIBProteus library
- DLLProteus model
- DSNProteus simulation
- INOArduino sketch
- HEXHEX firmware
Description
12V-to-230V-Pure-Sine-Wave-Inverter-Library-for-Proteus-v1.0.zip with the inverter for Proteus simulation (TEPINVERTER.LIB and TEPINVERTER.DLL), our 12V lead-acid battery, our Arduino UNO V4.0, the A3 demo with its sketch and a README.
File Structure
5.2 KB201.9 KB15.9 KB16.2 KB883.5 KB320 KB325 KB25.9 KB23.4 KB883.5 KB320 KB325 KB16.3 KBGallery12 images from the tutorialOpen the tutorial
The circuit, the board and the results as they appear in 12V to 230V Pure Sine Wave Inverter Library for Proteus Simulation. Open an image for its full size.












README
12V TO 230V PURE SINE WAVE INVERTER LIBRARY FOR PROTEUS SIMULATION - V1.0 (300 W, with its protections and a pop-up)
Designed by The Engineering Projects
www.TheEngineeringProjects.com
IMPORTANT LINKS
Article (read it first - pictures, step by step, every feature explained):
https://www.theengineeringprojects.com/2026/11/12v-to-230v-pure-sine-wave-inverter-library-for-proteus.html
Report a bug or suggest a feature (our forum):
https://www.theengineeringprojects.com/forum/category/motor-driver-proteus-library
The demo runs on our Arduino UNO V4.0 (included) - working LEDs, RESET and a
built-in serial monitor, no Virtual Terminal to wire - its own article:
https://www.theengineeringprojects.com/2026/10/arduino-uno-library-for-proteus-v40.html
The demo measures the battery with our INA219 library (installed from its own package - not in this zip):
https://www.theengineeringprojects.com/2026/10/ina219-current-sensor-library-for-proteus-v1-0.html
The demo's battery is our 12V Lead-Acid Battery library (its LIB and DLL are in this zip; its own article):
https://www.theengineeringprojects.com/2026/11/12v-lead-acid-battery-library-for-proteus.html
Support us (the libraries are free):
https://www.theengineeringprojects.com/donate
FILE STRUCTURE
Pure-Sine-Wave-Inverter-TEP-v1.0/
|-- Proteus Library Files/
| |-- ArduinoV4TEP.LIB 201.9 KB TEP Arduino boards V4.0 (UNO) -> LIBRARY
| |-- TEPINVERTER.LIB 15.9 KB the library -> LIBRARY folder
| |-- TEPLEADACID.LIB 16.2 KB a part the demo uses -> LIBRARY folder
|-- Proteus Model Files/
| |-- TEPARDUINO.DLL 883.5 KB the Arduino board model -> MODELS folder
| |-- TEPINVERTER.DLL 320.0 KB the model -> MODELS folder
| |-- TEPLEADACID.DLL 325.0 KB its model -> MODELS folder
|-- Proteus Simulation/
| |-- Inverter_Demo.hex 25.9 KB the demo firmware
| |-- Pure-Sine-Wave-Inverter-Battery-INA219-ArduinoUnoV4.pdsprj 23.4 KB the demo project
| |-- TEPARDUINO.DLL 883.5 KB copy of the board model
| |-- TEPINVERTER.DLL 320.0 KB copy of the model
| |-- TEPLEADACID.DLL 325.0 KB copy of its model
|-- Arduino Code/
| |-- Inverter_Demo/Inverter_Demo.ino 5.2 KB the demo sketch (source of the .hex)
|-- README.txt ~17.4 KB this file
Total: 3.28 MB (unzipped). The C++ source code of the models is not included.
WHAT IS IT?
A 300 W pure sine wave inverter - 12 V DC in, 230 V AC 50 Hz out, an aluminium case of 205 x 91 mm -
drawn at true scale
from above (the finned case with its two end caps, the label plate with the POWER and FAULT lamps,
the two battery posts on
the left and the mains lead on the right; our own drawing, no maker's mark). The figures are from
two makers' manuals:
* The output: 230 V rms, a sine wave with a little distortion (3.6 %; the makers allow 4 %), 50 Hz
(60 Hz by FREQ),
isolated from the battery side. It rises over a tenth of a second at switch-on.
* The input: the inverter takes from the battery what the load takes plus its losses - 3 W with no
load, 94 % efficient
at 100 W, 90 % at 300 W. The lower the battery's voltage, the more amperes for the same watts:
300 W need about 28 A.
* The battery-low ALARM sounds under 10.5 V; under 10.0 V the inverter shuts down and waits for
12.5 V; over 15.0 V it
shuts down until 14.5 V.
* 300 W for good and up to 600 W for a moment (a motor's start); more than that, or a short
circuit, cuts the output.
It tries again after 10 seconds of its clock; after the third cut it waits to be switched off
and on.
* The heat: the case warms with the losses; the fan starts at 40 C; over 55 C the output is cut
until 45 C.
* On the sheet the two lamps work at Run (POWER green, flashing with the alarm; FAULT red) and the
label plate shows the
state and both sides of the conversion. Click it at Run for the pop-up: the power flow with the
efficiency, one cycle
of the output's voltage and current as on a scope, eight live values; graphs, an event log and a
check page.
The body is drawn as on the real part and to true scale against our Arduino.
The TEP signature and the pop-up are TEP additions.
ONE DEVICE (search "INVERTER" in Pick Devices):
INVERTER12V230VTEP "Pure Sine Wave Inverter 12 V to 230 V 300 W V1.0" in TEPINVERTER.LIB
(Electromechanical >
Inverters), prefix INV, model TEPINVERTER.DLL (analog). Four pins: DC+ and DC-
on the left (the
battery), L and N on the right (the mains side, 230 V, isolated from the
battery side).
THE POP-UP
Click the part at Run. Tabs:
Inverter chips: the power switch; the clock (x 1, x 60, x 3600). The power flow from the
battery through the inverter
to the mains side, with the efficiency and the losses; one cycle of the output - the
voltage (blue) and the
current (orange) against the phase, with the rms values, the power and the power
factor; the three
conditions (on, alarm, shut down) with the one now lit; eight live values: the
battery's volts and amps,
the watts from the battery, the output's voltage and frequency, its current, its
power in W and VA, the
efficiency and the losses, the case's temperature and the fan, the watt-hours in and
out.
Graphs the live values over the last 2, 6 or 15 s. Live / Freeze.
Event log every change and warning; filters All / Changes / Warnings, Pause, Clear
Check what the part is doing and what to look at, each with a verdict (green = fine, amber
= check, red = wrong)
Settings theme, text size, open at Run, window size
Help report a bug, suggest a feature, article, updates, donate, forum; Copy diagnostics
for a bug report
TEST STATUS
V1.0: verified in Proteus 8.5 on 16 Nov 2026 (the demo project as shipped: an A3 sheet, an Arduino UNO V4.0).
What the runs showed (the model's own numbers and the sketch's monitor):
The demo as shipped (Inverter_Demo; INV1 SWITCH ON, 50 Hz; R1 2.1 k = a 25 W mains lamp on L and N;
BAT1 our lead-acid
battery SOC 60 %; the INA219 in the lead between the battery's + and DC+; SPEED 3600 on the battery
and the inverter),
one run (ivfinal1), the model's pauses:
* ON at 0.020 s, the battery at 12.42 V. At 0.5 s: 230 V 50 Hz, 0.109 A, 25.1 W to the lamp (power
factor 1.00);
2.40 A from the battery at 11.80 V, 28.3 W in, 3.2 W lost, 89 % efficient; the case 31 C, the
fan off.
* At 0.5 s the other pop-ups: the battery 2.40 A out at 12.05 V, 42 % left (57 min to empty at
this rate); the
INA219 (U1) 12.032 V on the bus, -239.99 mV on the shunt, -2.400 A (minus: out of the battery).
The inverter gets
a quarter of a volt less than the battery has: the shunt's drop.
* The battery runs down, the current rises: at 1.0 s 11.48 V and 2.47 A, the output unchanged (230
V, 25.1 W).
* BATTERY LOW ALARM at 1.400 s (10.32 V): at 1.41 s 10.32 V and 2.75 A, the lamp still alight.
* SHUT DOWN at 1.420 s (9.87 V, under 10.0 V): the output is cut, 20 mA from the battery. At 1.8 s
the battery
stands at 9.69 V; its pop-up: DEEP DISCHARGE, 0 % left after 3.24 Ah, 9.71 V. The lamp was
alight for 1 h 24 min.
* In all 37.5 Wh from the battery, 33.0 Wh to the lamp; the battery between 9.35 V and 12.42 V;
the case 31 C at
most; the output was cut once.
* The monitor: running from 12.21 V 2.36 A to 10.60 V 2.67 A, then shut down: the battery is low
(9.73 V 0.02 A); it
ended at 3.08 Ah and 36.1 Wh. 107 s for the 1.8 s of the run.
A second run with a short circuit on the output (ivshort1: R1 1 ohm): SHORT CIRCUIT at 26.6 ms, 6 A
- cut at once;
tried again at 40 ms and 60 ms; after the third cut (66.2 ms) the output stays off until the
inverter is switched off
and on; the battery at 12.41 V gives 20 mA.
INSTALLATION (about 2 minutes)
1. Close Proteus. Extract the WHOLE ZIP to a normal folder (e.g. Desktop).
2. Copy everything in "Proteus Library Files" (TEPINVERTER.LIB, TEPLEADACID.LIB and our Arduino
library V4.0, ArduinoV4TEP.LIB, with the ARDUINO UNO V4.0 used by the demo) to the LIBRARY folder of
Proteus, for example:
C:\Program Files (x86)\Labcenter Electronics\Proteus 8 Professional\LIBRARY
(use the folder that already holds Proteus's own .LIB files).
3. Copy TEPINVERTER.DLL, TEPLEADACID.DLL and TEPARDUINO.DLL from "Proteus Model Files" to the MODELS
folder (...\Proteus 8 Professional\MODELS).
4. Delete TEPINVERTER.IDX from the LIBRARY folder if it is there (Proteus makes a new index).
5. Start Proteus. In Pick Devices (P) search "INVERTER".
RUN THE DEMO
"Proteus Simulation\Pure-Sine-Wave-Inverter-Battery-INA219-ArduinoUnoV4.pdsprj" (an A3 sheet) - keep
the .hex file and the DLLs beside the project.
A battery, the inverter and a mains load:
ARD1: Arduino UNO V4.0 running Inverter_Demo.hex, its serial monitor built in (window "TEP
Arduino UNO - ARD1").
INV1: the inverter: switch on, 50 Hz, SPEED 3600; DC- on ground.
U1: our INA219 (its pop-up version) between the inverter's DC+ (VIN+) and the battery's +
(VIN-); SDA A4, SCL A5.
BAT1: our 12 V 7.2 Ah lead-acid battery, SOC 60 %, SPEED 3600 (an hour each simulated second), -
on ground.
R1: 2.1 k between L and N: a 25 W mains lamp.
The sketch takes sixteen readings and works with their mean, tells the inverter's state
from the battery's side,
and counts the amp-hours and watt-hours taken from the battery; the UNO's LED warns under
10.5 V.
Closed the monitor? Click the UNO's USB port.
WIRING (the same in Proteus and on a real board)
The battery on DC+ / DC- with short, thick leads; the load between L and N. The mains side carries
230 V and is isolated
from the battery side: do not join N to the battery's -. Never connect the output to the mains or
to another inverter.
REAL HARDWARE:
* Size the battery, not only the inverter: 300 W take about 28 A, which empties a 7 Ah battery in
minutes. The demo's
25 W lamp takes 2.3 A.
* A motor, a pump or a fridge needs several times its power for a moment at the start: that is what
the 600 W are for.
* The low-battery alarm is a warning to stop: a lead-acid battery that is run down to 10 V often
suffers.
* The INA219 of the demo measures up to 3.2 A; for a larger load use a shunt or a Hall sensor made
for the current.
THE DEMO SKETCH ON THE SERIAL MONITOR (Inverter_Demo V1.0, 9600 baud)
The sketch reports every 300 ms. Type a command:
reset the counters back to 0 rate 1000 report every 1000 ms help
EXPECTED MONITOR OUTPUT
Inverter battery monitor - The Engineering Projects
A: out of the battery, into the inverter. Clock x 3600: a simulated second is an hour.
Commands: reset | rate 300 | help
Battery 12.21 V 2.36 A 28.9 W running 0.00 Ah 0.0 Wh
Battery 12.04 V 2.40 A 28.9 W running 0.71 Ah 8.7 Wh
Battery 11.86 V 2.44 A 28.9 W running 1.44 Ah 17.3 Wh
Battery 11.64 V 2.48 A 28.9 W running 2.18 Ah 26.0 Wh
Battery 10.60 V 2.67 A 28.3 W running 2.94 Ah 34.6 Wh
Battery 9.73 V 0.02 A 0.2 W shut down: the battery is low 3.08 Ah 36.1 Wh
PROPERTIES (double-click the part > Edit Properties)
Power switch (SWITCH) ON or OFF at the start; the pop-up's Switch chip works it at
Run (ON)
Output frequency (FREQ) 50 or 60 Hz (50)
Air temperature (TEMP) around the inverter, C: the losses add to it; -10 - 50 (25)
Clock (SPEED) 1 real time, 3600 an hour each simulated second - the same as
the battery's, 1 - 7200 (1)
Every run starts again from the properties.
LINKS.INI (OPTIONAL)
The Help page cards of the pop-up open web pages. To point them somewhere else without a new DLL,
put a text file named links.ini next to TEPINVERTER.DLL with lines KEY=URL, for example:
ARTICLE=https://www.theengineeringprojects.com/...
Keys: WEBSITE, FORUM, BUG_REPORT, FEATURE_REQUEST, ARTICLE, USER_GUIDE,
UPDATE_CHECK, DONATE. Only http:// and https:// links are used; lines starting
with # are comments.
TROUBLESHOOTING
* No output, POWER lamp dark: the switch is off, or nothing is on DC+ / DC-.
* SHUT DOWN: BATTERY LOW: the battery fell under 10.0 V. It comes back at 12.5 V: charge the
battery.
* The alarm sounds although the battery is not empty: the leads lose voltage. Measure at the
inverter's posts.
* SHUT DOWN: OVERLOAD or SHORT CIRCUIT: too much load, or L and N are joined. Remove the cause;
after three tries the
inverter waits for the switch.
* The output reads 20 to 30 V low on a simple meter: use a true-rms meter (in Proteus, an AC
voltmeter).
* A long simulation is slow: the model follows every cycle of the 50 Hz. Keep runs to a few seconds.
* The part is not simulated: TEPINVERTER.DLL is missing from MODELS and from the project folder. No
UNO / no monitor window: TEPARDUINO.DLL is missing, or click the UNO's USB port.
BUG REPORTS AND FEATURE REQUESTS
Please post them in our forum with a screenshot, the Serial Monitor text, the
simulation log and the pop-up's Copy diagnostics text:
https://www.theengineeringprojects.com/forum/category/motor-driver-proteus-library
SUPPORT US
This library is free. If it saves you time, please support our work:
https://www.theengineeringprojects.com/donate
WEBSITE
https://www.theengineeringprojects.com/
LICENCES AND THIRD-PARTY NOTES
* The model (TEPINVERTER.DLL), the symbols and artwork, the other parts of ours in the demo and the
Arduino Library V4.0 (ArduinoV4TEP.LIB / TEPARDUINO.DLL, with its built-in TEP Serial Monitor
Advance) are made by The Engineering Projects. The models use only standard Windows libraries; no
Visual C++ redistributable is needed.
The C++ source code is not included.
* Arduino UNO V4.0 (ArduinoV4TEP.LIB / TEPARDUINO.DLL, our Arduino Library V4.0 - its
microcontroller is Proteus's own AVR model): The Engineering Projects,
https://www.theengineeringprojects.com/2026/10/arduino-uno-library-for-proteus-v40.html
* The .hex file is built from the demo sketch and the Arduino AVR core 1.8.6, which includes
LGPL-licensed code; its source code is available at
https://github.com/arduino/ArduinoCore-avr/tree/1.8.6
* Proteus is a product of Labcenter Electronics and is not included. Arduino is a trademark of Arduino SA.
This library is not made or endorsed by Arduino or Labcenter.
REBUILDING THE FIRMWARE (OPTIONAL)
The HEX file is supplied; Arduino IDE is not needed to run the demo. To edit the sketch, open
Arduino Code\Inverter_Demo\Inverter_Demo.ino, select Arduino Uno and use Sketch > Export Compiled
Binary. Replace the simulation's .hex with the exported HEX. The sketch needs 9,406 bytes of flash
and 512 bytes of RAM.
MODEL SCOPE AND LIMITS
Modelled: the output as a sine source of 230 V rms with a little third and fifth harmonic behind 2
ohm (ours), rising over
0.1 s; the isolation of the mains side; the battery's current from the load's mean power of the last
cycle and the losses
(3 W + 0.000337 x P x P - ours, fitted to the makers' 90 % at full load and about 95 % at a third);
the battery-low alarm
and shutdown, the high-voltage shutdown; the overload and short-circuit cut-off with retries; the
case's heat, the fan and
the over-temperature cut-off; the two lamps; SPEED. Not modelled: the switching inside (far above
what a circuit simulation
can step through), the USB port, the buzzer's sound, the fuse and reverse-polarity damage, earth
leakage.
VERSION
TEP Pure Sine Wave Inverter library V1.0 (Nov 2026). Device INVERTER12V230VTEP (TEPINVERTER.LIB /
TEPINVERTER.DLL). Demo sketch Inverter_Demo V1.0 (the INA219 read straight with Wire). The demo also
uses our 12V Lead-Acid Battery (TEPLEADACID: LEADACIDBAT12V7TEP), shipped in this package. Demo
board: ARDUINO UNO V4.0 (TEP Arduino Library V4.0) with its built-in serial monitor.Development1 release
-
V1.012V to 230V Pure Sine Wave Inverter Library for Proteus V1.0this page
V1.0 is the only release in the Download Center so far. When a newer version is published, it appears above with its own download page.
Installation8 steps
From the download to a working project, in order. The steps follow what the package contains.
You will need
- Proteus Design SuiteProteus 8 or newer (Labcenter), on Windows
- Arduino IDE1.8 or 2.x, with the board of the tutorial chosen under Tools → Board
- Any archive toolWindows, macOS and Linux extract ZIP files on their own
Steps
- 1
Extract the archive
Right-click ac1174eaab904127a8a30f534e659a26.zip and choose Extract All (or open it with 7-Zip or WinRAR) into a folder you can find again. Keep its folder structure (Pure-Sine-Wave-Inverter-TEP-v1.0) as it is.
- 2
Copy the library files into Proteus
Move ArduinoV4TEP.LIB, TEPINVERTER.LIB and TEPLEADACID.LIB and the files into the LIBRARY folder of your Proteus installation: C:\Program Files (x86)\Labcenter Electronics\Proteus 8 Professional\LIBRARY for Proteus 8, or the matching Proteus 7 folder. Older versions keep it under ProgramData\Labcenter Electronics. If Proteus is open, close it first.
- 3
Add the simulation model
Copy TEPARDUINO.DLL, TEPINVERTER.DLL and TEPLEADACID.DLL into the MODELS folder next to LIBRARY, so the component can run, not only be drawn.
- 4
Restart Proteus and place the component
Start Proteus, open a schematic, press P (Pick Devices) and search for the component by the name used in the tutorial. It appears with its pins ready to wire.
- 5
Open the sketch in the Arduino IDE
Open Inverter_Demo.ino, select your board and port under Tools, then Verify. Sketch → Export Compiled Binary writes the HEX file a simulation needs.
- 6
Load the HEX file
In Proteus double-click the microcontroller, set Program File to Inverter_Demo.hex and run the simulation. For real hardware, flash the same file with your programmer.
- 7
Open the example simulation
Open Pure-Sine-Wave-Inverter-Battery-INA219-ArduinoUnoV4.pdsprj in Proteus to see the wiring exactly as in the tutorial. Check the controller's Program File path, then press Play.
- 8
Follow the tutorial
12V to 230V Pure Sine Wave Inverter Library for Proteus Simulation explains every connection and setting in order; keep it open beside the files while you build.
FAQs9 questionsContact TEP
How do I download 12V to 230V Pure Sine Wave Inverter Library for Proteus V1.0?
Wait for the 30-second guest countdown on this page, then press the download button; the file comes straight from our storage. Members who are logged in skip the wait. If the browser opens the file instead of saving it, use its Save as option. The download link is made for you when the countdown ends and works for 15 minutes; a saved or shared link stops working, so share this page instead.
What is inside the archive?
12V to 230V Pure Sine Wave Inverter Library for Proteus V1.0 comes as a ZIP archive of 13 files (1.5 MB, 3.3 MB unpacked) holding Proteus library files, simulation model DLLs, a Proteus simulation, an Arduino sketch and compiled HEX firmware. Open the File Structure tab for the full list of 13 files.
What should I do if the download does not start?
Check the browser's download list first; an ad blocker or a company firewall can also hold it back, so try another browser or network. If the file arrives incomplete, download it again. For an installation problem, read the Install tab or tell us in the comments with your software version and the exact error message.
Is this file free?
Yes. Every file in the TEP Download Center is free for learning, personal and student projects. If you share it, link back to this page or the tutorial so others find the latest version.
How do I check that the file arrived complete?
Compare its SHA-256 with the one on this page, 2ba0ce390f7796ef3c9e1cfa330bd10bf8fc42b430883f13e7649a4c16d59e2a. In PowerShell run Get-FileHash "ac1174eaab904127a8a30f534e659a26.zip"; on macOS or Linux run shasum -a 256 "ac1174eaab904127a8a30f534e659a26.zip". The same value means the file is exactly the one in our storage; a different one means the download broke off, so download it again.
Do I need WinRAR to open the ZIP file?
No. Windows, macOS and Linux open ZIP archives on their own (Extract All, or double-click). WinRAR and 7-Zip work too. Extract the whole archive before using the files.
Where do I put the LIB and IDX files?
Both files go into the LIBRARY folder of your Proteus installation (Proteus 8: C:\Program Files (x86)\Labcenter Electronics\Proteus 8 Professional\LIBRARY; Proteus 7 has the same folder under its own name). Restart Proteus afterwards and search for the component with P.
Which Proteus version does the library need?
The tutorial names the Proteus version the library was made and tested with. Most TEP libraries work in Proteus 7 and Proteus 8; if the component does not appear after a restart, check that both the LIB and the IDX file were copied and that Proteus was fully closed while copying.
How do I get the HEX file into the simulation?
Compile the sketch in the Arduino IDE (Sketch → Export Compiled Binary gives you the HEX next to the sketch), then in Proteus double-click the board, set Program File to that HEX and run.
Members skip the wait. Log in or join TEP.
- 0Total downloads
- 4%Popularity
- ProteusCategory
- 0Comments
- ssyedzainnasirUploaded by
- 16 Nov 2026Uploaded at
2ba0ce390f7796ef3c9e1cfa330bd10bf8fc42b430883f13e7649a4c16d59e2a
















Comments
0