TEP DOWNLOAD CENTER

Project Files of IoT Robot Arm Controller with Raspberry Pi 5 - Proteus Simulation

Libraries Code Projects Simulation
tep://download-terminal 33120f3f8f9e4e9b9f12cb457b3ca52a.zip ZIP archiveV1.0Verified0 downloadsFree
IoT Robot Arm Controller with Raspberry Pi 5 - Proteus Simulation: the Raspberry Pi 5, the PCA9685 servo driver and the 4-DOF robot arm with its block
Proteus library · File 1 of 1

IoT Robot Arm Controller with Raspberry Pi 5 - Proteus Simulation V1.0

IoT Robot Arm Controller with Raspberry Pi 5 - Proteus Simulation V1.0 comes as a ZIP archive of 135 files (13.4 MB, 26.0 MB unpacked) holding Proteus library files, simulation model DLLs, a Proteus simulation, source code and a nested archive.

  • LIBProteus library
  • DLLProteus model
  • DSNProteus simulation
  • SRCSource code
  • ZIPNested archive

Description

IoT-Robot-Arm-Controller-Raspberry-Pi-5-Proteus-Simulation-v1.0.zip: the complete Proteus simulation project (Raspberry Pi 5, PCA9685 servo driver, 4-DOF robot arm, the Laptop and Mobile WiFi Monitors), the Python program robot_arm.py, every LIB and DLL the simulation needs, the TEPPi Python runtime and a README.

Read IoT Robot Arm Controller with Raspberry Pi 5 - Proteus Simulation

File Structure

33120f3f8f9e4e9b9f12cb457b3ca52a.zip135 files · 24 folders · 26.0 MB unpacked
Pi-5-Robot-Arm-TEP-v1.0/135 files · 26.0 MB
Proteus Library Files/5 files · 253.4 KB
LIB TEPLAPTOP.LIBProteus library 39.5 KB
LIB TEPMOBILE.LIBProteus library 13.1 KB
LIB TEPPCA9685.LIBProteus library 129.4 KB
LIB TEPROBOTARM.LIBProteus library 11 KB
LIB TEPRPI5.LIBProteus library 60.5 KB
Proteus Model Files/123 files · 22.2 MB
TEPPi/120 files · 18.7 MB
python/33 files · 17.5 MB
DLL libcrypto-3.dllSimulation model 3.3 MB
DLL libffi-8.dllSimulation model 34.3 KB
DLL libssl-3.dllSimulation model 620.8 KB
TXT LICENSE.txtText file 36 KB
PYD pyexpat.pydPYD file 169.8 KB
CAT python.catCAT file 628.1 KB
EXE python.exeEXE file 99.3 KB
DLL python3.dllSimulation model 65.3 KB
DLL python311.dllSimulation model 4.8 MB
ZIP python311.zipArchive 4.1 MB
_PTH python311._pth_PTH file 80 B
EXE pythonw.exeEXE file 97.8 KB
PYD select.pydPYD file 26.8 KB
DLL sqlite3.dllSimulation model 1.2 MB
PYD unicodedata.pydPYD file 1.1 MB
DLL vcruntime140.dllSimulation model 88.9 KB
PYD winsound.pydPYD file 27.3 KB
PYD _asyncio.pydPYD file 55.8 KB
PYD _bz2.pydPYD file 79.8 KB
PYD _ctypes.pydPYD file 105.8 KB
PYD _decimal.pydPYD file 193.8 KB
PYD _elementtree.pydPYD file 113.8 KB
PYD _hashlib.pydPYD file 48.8 KB
PYD _lzma.pydPYD file 145.8 KB
PYD _msi.pydPYD file 36.8 KB
PYD _multiprocessing.pydPYD file 29.3 KB
PYD _overlapped.pydPYD file 42.3 KB
PYD _queue.pydPYD file 28.8 KB
PYD _socket.pydPYD file 67.3 KB
PYD _sqlite3.pydPYD file 89.3 KB
PYD _ssl.pydPYD file 153.8 KB
PYD _uuid.pydPYD file 22.8 KB
PYD _zoneinfo.pydPYD file 38.8 KB
runtime/87 files · 1.1 MB
Adafruit_BBIO/6 files · 22.6 KB
PYC ADC.pycPYC file 2.1 KB
PYC GPIO.pycPYC file 9.9 KB
PYC PWM.pycPYC file 4.1 KB
PYC UART.pycPYC file 1.3 KB
PYC _pins.pycPYC file 4.7 KB
PYC __init__.pycPYC file 431 B
Adafruit_DHT/1 file · 2.5 KB
PYC __init__.pycPYC file 2.5 KB
arduino/2 files · 17.7 KB
app_utils/1 file · 17.5 KB
PYC __init__.pycPYC file 17.5 KB
PYC __init__.pycPYC file 283 B
colorzero/8 files · 85.3 KB
SRC attr.pySource file 6.5 KB
SRC color.pySource file 37.9 KB
SRC conversions.pySource file 11.1 KB
SRC deltae.pySource file 5.5 KB
SRC easings.pySource file 885 B
SRC tables.pySource file 13.6 KB
SRC types.pySource file 9 KB
SRC __init__.pySource file 878 B
colorzero-2.0.dist-info/5 files · 6.6 KB
TXT LICENSE.txtText file 1.5 KB
FILE METADATAFile 4 KB
FILE RECORDFile 1004 B
TXT top_level.txtText file 10 B
FILE WHEELFile 110 B
gpiozero/27 files · 594.5 KB
fonts/3 files · 12.6 KB
TXT 14seg.txtText file 2.6 KB
TXT 7seg.txtText file 1.1 KB
SRC __init__.pySource file 8.9 KB
pins/11 files · 234.3 KB
SRC data.pySource file 58.5 KB
SRC lgpio.pySource file 12.4 KB
SRC local.pySource file 6.6 KB
SRC mock.pySource file 18.5 KB
SRC native.pySource file 20.7 KB
SRC pi.pySource file 27.8 KB
SRC pigpio.pySource file 21.1 KB
SRC rpigpio.pySource file 7.1 KB
SRC spi.pySource file 7.7 KB
SRC style.pySource file 2.7 KB
SRC __init__.pySource file 51.2 KB
SRC boards.pySource file 100.9 KB
SRC compat.pySource file 1.2 KB
SRC devices.pySource file 24.3 KB
SRC exc.pySource file 7.4 KB
SRC input_devices.pySource file 53.6 KB
SRC internal_devices.pySource file 26.1 KB
SRC mixins.pySource file 20.5 KB
SRC output_devices.pySource file 60.5 KB
SRC spi_devices.pySource file 19.6 KB
SRC threads.pySource file 1.6 KB
SRC tones.pySource file 8.4 KB
SRC tools.pySource file 20.9 KB
SRC __init__.pySource file 2.6 KB
gpiozero-2.0.1.post3.dist-info/6 files · 14.6 KB
TXT entry_points.txtText file 539 B
RST LICENSE.rstRST file 1.4 KB
FILE METADATAFile 9.7 KB
FILE RECORDFile 2.8 KB
TXT top_level.txtText file 21 B
FILE WHEELFile 92 B
Jetson/2 files · 8.2 KB
GPIO/1 file · 7.9 KB
PYC __init__.pycPYC file 7.9 KB
PYC __init__.pycPYC file 264 B
micropython/11 files · 142.1 KB
PYC dht.pycPYC file 3.4 KB
PYC ds18x20.pycPYC file 3.8 KB
PYC framebuf.pycPYC file 17.5 KB
PYC machine.pycPYC file 55.2 KB
PYC micropython.pycPYC file 3.3 KB
PYC network.pycPYC file 10.8 KB
PYC ntptime.pycPYC file 1.5 KB
PYC onewire.pycPYC file 4.2 KB
PYC requests.pycPYC file 7.3 KB
PYC rp2.pycPYC file 2.5 KB
PYC tep_mpy.pycPYC file 32.6 KB
OPi/2 files · 14.8 KB
PYC GPIO.pycPYC file 14.5 KB
PYC __init__.pycPYC file 283 B
RPi/2 files · 17.6 KB
PYC GPIO.pycPYC file 17.4 KB
PYC __init__.pycPYC file 257 B
serial/2 files · 15.2 KB
PYC serialutil.pycPYC file 691 B
PYC __init__.pycPYC file 14.5 KB
smbus2/1 file · 12.8 KB
PYC __init__.pycPYC file 12.8 KB
PYC adafruit_dht.pycPYC file 3.6 KB
PYC board.pycPYC file 1.7 KB
PYC lgpio.pycPYC file 37 KB
PYC smbus.pycPYC file 418 B
PYC spidev.pycPYC file 6.2 KB
PYC tep_opi.pycPYC file 7 KB
PYC tep_pi.pycPYC file 37.3 KB
PYC tep_pi_boot.pycPYC file 10.6 KB
PYC tep_pi_fs.pycPYC file 23.7 KB
PYC tep_pi_net.pycPYC file 28.7 KB
PYC tep_pi_w1.pycPYC file 8.8 KB
PYC wiringpi.pycPYC file 16.9 KB
DLL TEPNET.DLLSimulation model 2.9 MB
DLL TEPPCA9685.DLLSimulation model 323 KB
DLL TEPROBOTARM.DLLSimulation model 317.5 KB
Proteus Simulation/5 files · 3.6 MB
DSN Pi-5-Robot-Arm.pdsprjProteus simulation 30.6 KB
SRC robot_arm.pySource file 17 KB
DLL TEPNET.DLLSimulation model 2.9 MB
DLL TEPPCA9685.DLLSimulation model 323 KB
DLL TEPROBOTARM.DLLSimulation model 317.5 KB
Python Code/1 file · 17 KB
SRC robot_arm.pySource file 17 KB
TXT README.txtText file 10.6 KB

README

README.txt 141 lines
===============================================================================================================
  IoT Robot Arm Controller with Raspberry Pi 5 - Proteus Simulation Project V1.0
  The Engineering Projects - www.TheEngineeringProjects.com
===============================================================================================================

IMPORTANT LINKS
  The project tutorial (circuit, code, simulation results):
    https://www.theengineeringprojects.com/2026/11/iot-robot-arm-controller-raspberry-pi-5-proteus-simulation.html
  The libraries this project is built from (each post has its own full download and tutorial):
    Raspberry Pi 5 board:
      https://www.theengineeringprojects.com/2026/10/raspberry-pi-5-library-for-proteus.html
    PCA9685 16-channel PWM / servo driver:
      https://www.theengineeringprojects.com/2026/10/pca9685-servo-driver-library-for-proteus-v1-0.html
    4-DOF robot arm (four SG90 servos):
      https://www.theengineeringprojects.com/2026/11/4-dof-robot-arm-library-for-proteus.html
    Laptop WiFi Monitor:
      https://www.theengineeringprojects.com/2026/10/laptop-wifi-monitor-library-for-proteus.html
    Mobile WiFi Monitor:
      https://www.theengineeringprojects.com/2026/10/mobile-wifi-monitor-library-for-proteus.html
  Support our free work: https://www.theengineeringprojects.com/donate

FILE STRUCTURE
Pi-5-Robot-Arm-TEP-v1.0/
|-- Proteus Library Files/
|   |-- TEPLAPTOP.LIB                                  39.5 KB   a part of the project -> LIBRARY folder
|   |-- TEPMOBILE.LIB                                  13.1 KB   a part of the project -> LIBRARY folder
|   |-- TEPPCA9685.LIB                                129.4 KB   a part of the project -> LIBRARY folder
|   |-- TEPROBOTARM.LIB                                11.0 KB   a part of the project -> LIBRARY folder
|   |-- TEPRPI5.LIB                                    60.5 KB   a part of the project -> LIBRARY folder
|-- Proteus Model Files/
|   |-- TEPNET.DLL                                     2.89 MB   a model -> MODELS folder
|   |-- TEPPCA9685.DLL                                323.0 KB   a model -> MODELS folder
|   |-- TEPROBOTARM.DLL                               317.5 KB   a model -> MODELS folder
|   |-- TEPPi/python/                                 17.54 MB   Python 3.11 embeddable -> MODELS\TEPPi (33 files)
|   |-- TEPPi/runtime/                                 1.11 MB   TEP Pi runtime, gpiozero -> MODELS\TEPPi (87 files)
|-- Proteus Simulation/
|   |-- Pi-5-Robot-Arm.pdsprj                          30.6 KB   the project simulation
|   |-- robot_arm.py                                   17.0 KB   the program PI1 runs
|   |-- TEPNET.DLL                                     2.89 MB   copy of the model
|   |-- TEPPCA9685.DLL                                323.0 KB   copy of the model
|   |-- TEPROBOTARM.DLL                               317.5 KB   copy of the model
|-- Python Code/
|   |-- robot_arm.py                                   17.0 KB   the program (the same file)
|-- README.txt                                        ~11.2 KB   this file
Total: 26.01 MB (unzipped). The C++ source code of the models is not included.

WHAT IS IT?
  A robot arm controller you can run in Proteus: a Raspberry Pi 5 drives a 4-DOF desktop robot arm (four SG90
  servos) through a PCA9685 16-channel PWM / servo driver on I2C, works out the joint angles for a point (inverse
  kinematics), moves smoothly, carries a block between two stands, jogs the claw in millimetres, records and plays
  poses, and serves a web dashboard.
    * PCA9685 board (PCA9685ADVTEP, PCA1) at 0x40 on I2C1: SDA = GPIO2 (pin 3), SCL = GPIO3 (pin 5), OE = GPIO4
      (pin 7, HIGH = every output off), GND (pin 6). VCC on a +3.3V power terminal (it stands for the Pi's 3.3 V pin
      1: the Pi model's supply pins are digital); V+ (the servo headers) on the 5 V rail. PRE_SCALE 121 = 50.03 Hz,
      one count = 4.88 us.
    * 4-DOF robot arm (ROBOTARM4DOFTEP, M1): BASE on PWM0, SHOULDER on PWM1, ELBOW on PWM2, GRIP on PWM3; V+ on the
      5 V rail. Each SG90: a pulse every 20 ms, 544 - 2400 us = 0 - 180 degrees. Drawn at true scale from the side;
      click it at Run for its pop-up (the side view, the top view with the stands and the block, the servos).
    * RASPBERRY PI 5 (PI1) runs robot_arm.py on Ethernet at 192.168.1.51 (port 8000).
    * Laptop WiFi Monitor (PC1) and Mobile WiFi Monitor (MOB1) open http://192.168.1.51:8000/.
  The geometry (at the top of the program): the shoulder pivot 55 mm above the table, the upper arm 80 mm, the
  forearm 80 mm (ELBOW 90 = level, a parallel linkage), the claw 45 mm past the wrist and always level.
    claw out = 80 cos(SHOULDER) + 80 cos(ELBOW - 90) + 45 mm;  up = 55 + 80 sin(SHOULDER) + 80 sin(ELBOW - 90) mm
  The joints the program asks: BASE 0 - 180, SHOULDER 45 - 145, ELBOW 25 - 155, GRIP 60 - 120 (120 open, 85 holds
  the 16 mm block). Every move at 60 degrees a second, 50 steps a second; at power-up OE stays HIGH until every
  channel has its home pulse (no jump).
  PICK AND PLACE: open; above the block (139 mm out, 100 mm up); down (139, 63); close (85); lift (120, 105); turn
  the base to the other stand (90 straight ahead, 150 = 60 degrees left); lower (139, 65); let go; up; home. The
  next one carries the block back; after a STOP with the block in the claw it finishes the move.
  Its pages:
    /                                  the dashboard: the controls, the claw, the joints, the counts, the events
    /home /pick /stop                  the home pose, a pick-and-place cycle, stop where it is
    /left /right /up /down /out /in    the base 15 degrees, the claw 10 mm (refused when out of reach)
    /open /close                       the claw
    /record /play /clear               up to 8 stored poses
    /data                              everything as JSON
  No extra Python library: lgpio (in the TEPPi runtime, and on Raspberry Pi OS), math, threading, http.server.

TEST STATUS
  Tested in Proteus 8 Professional on Windows 11, the run that made the tutorial's screenshots (the program's times):
    * Start: "PCA9685 at 0x40: PRE_SCALE 121 = 50.03 Hz, one count = 4.88 us"; HOME (the claw 125 mm out, 135 mm up).
      The PCA9685: RUNNING 50.0 Hz, 4 servo pulses - 1474 us (302 counts) on CH0 - CH2, 1781 us (365) on CH3;
      VCC 3.30 V, V+ 5.00 V, OE LOW. The arm: 0.02 A at rest.
    * PICK AND PLACE (laptop) at 17.7 s: above the block 18.5 s; down to the block 19.4 s (SHOULDER 58.7, ELBOW 41.0
      asked; 59.8 / 41.9 real); the claw closed 20.5 s - the jaws stopped at 92 deg on the block (85 asked), HOLDING,
      0.56 A; lift 21.4 s; turned to the place stand 22.9 s; lowered 23.8 s; let go 24.9 s; home 27.3 s; "cycle 1
      done: the block on the PLACE STAND" at 27.7 s (10 s a cycle).
    * OUT x5 from the phone: 135 / 145 / 155 / 165 / 175 mm out at 135 mm up (SHOULDER 49.0, ELBOW 104.2 at 175);
      the 6th "OUT refused: (185, 135) mm is out of reach" (the wrist 161.2 mm from the shoulder).
    * Teach: RECORD pose 1; LEFT x2 (base 120); DOWN x3 (175 mm out, 105 mm up: 50.5 / 81.6); RECORD pose 2; HOME;
      RECORD pose 3; PLAY at 81.2 s - the poses at 81.9, 82.9 and 84.0 s, "PLAY done" at 84.4 s.
    * PICK AND PLACE back at 87.8 s; STOP at 92.7 s while the base turned with the block in the claw - the arm held
      it; PICK AND PLACE at 100.7 s: "the block is in the claw - on to the PICK STAND"; "cycle 2 done" at 106.0 s.
  An earlier run showed why go() checks STOP after a move: STOP sets every target to the present angle, so the move
  in progress looked "arrived" and the sequence printed its next point before it stopped.
  116 s of simulation took about 7.5 minutes on our PC with all the captures.

INSTALLATION
  1. Close Proteus. Extract the WHOLE zip file, for example to your Desktop.
  2. Copy the files from "Proteus Library Files" into the LIBRARY folder of Proteus, for example
     C:\Program Files (x86)\Labcenter Electronics\Proteus 8 Professional\LIBRARY
  3. Copy everything in "Proteus Model Files" - the DLL files and the TEPPi folder - into the MODELS folder (next
     to LIBRARY).
  4. Start Proteus. Press P in the schematic and search for RASPBERRY PI 5, PCA9685ADVTEP or ROBOTARM4DOFTEP to
     check that the parts are there.

RUN THE SIMULATION
  1. Open "Proteus Simulation\Pi-5-Robot-Arm.pdsprj". Keep robot_arm.py and the DLL files beside it.
  2. Press Play. The Pi's terminal opens, the arm goes to its home pose (the claw 125 mm out, 135 mm up).
  3. Open the Laptop WiFi Monitor (PC1) or the Mobile WiFi Monitor (MOB1) and press Go.
  4. Press PICK AND PLACE and watch the arm on the sheet; click the arm for its pop-up.
  5. Try the jogs, RECORD a few poses and PLAY them, STOP the arm in the middle of a move.
  Your own program: edit robot_arm.py beside the project (PI1's PROGRAM property) and press Play again.

PROPERTIES USED IN THIS PROJECT
  PI1 RASPBERRY PI 5           PROGRAM=robot_arm.py, ETHERNET=IN (192.168.1.51)
  PCA1 PCA9685ADVTEP           (no changes: address 0x40, oscillator 25 MHz)
  M1 ROBOTARM4DOFTEP           (no changes)
  PC1, MOB1                    HOMEPAGE=http://192.168.1.51:8000/

TROUBLESHOOTING
  * The program stops with an I2C error: SDA / SCL swapped, or the PCA9685's address jumpers not 0x40.
  * No servo moves: OE is HIGH (all outputs off) or V+ has no supply.
  * The servos buzz or the angles are wrong: not 50 Hz - PRE_SCALE is ignored unless the chip sleeps (MODE1 0x10).
  * A jog does nothing: the point is out of reach - the dashboard's events say so.
  * The claw misses the block: the arm's lengths in the program do not match the arm.
  * The terminal cannot start Python: the TEPPi folder is not in MODELS.

LICENCES
  * The project, the program, the parts (LIB files) and the models (DLL files) are made by The Engineering Projects
    and are free for learning and for your own projects. The models use only standard Windows libraries.
    The C++ source code of the models is not included; the source code is not included for any model.
  * TEPPi\python is the Python 3.11 Windows embeddable package (Python Software Foundation License); TEPPi\runtime
    holds our TEP Pi runtime with gpiozero and colorzero (BSD licences) - their licence files are inside the folders.
  * Proteus is a product of Labcenter Electronics and is not included. Raspberry Pi is a trademark of Raspberry Pi
    Ltd; PCA9685 is a product of NXP Semiconductors; the arm is a generic kit. This project is not made or endorsed
    by them.

VERSION
  V1.0 - the first release of the project.
===============================================================================================================
Advertisement

Development1 release

  1. V1.0IoT Robot Arm Controller with Raspberry Pi 5 - Proteus Simulation V1.0this page

    V1.0 is the only release in the Download Center so far. When a newer version is published, it appears above with its own download page.

Installation7 steps

From the download to a working project, in order. The steps follow what the package contains.

You will need

  • Proteus Design SuiteProteus 8 or newer (Labcenter), on Windows
  • Pythonto build the source files into firmware
  • Any archive toolWindows, macOS and Linux extract ZIP files on their own

Steps

  1. 1

    Extract the archive

    Right-click 33120f3f8f9e4e9b9f12cb457b3ca52a.zip and choose Extract All (or open it with 7-Zip or WinRAR) into a folder you can find again. Keep its folder structure (Pi-5-Robot-Arm-TEP-v1.0) as it is.

  2. 2

    Copy the library files into Proteus

    Move TEPLAPTOP.LIB, TEPMOBILE.LIB and TEPPCA9685.LIB and 2 more and the files into the LIBRARY folder of your Proteus installation: C:\Program Files (x86)\Labcenter Electronics\Proteus 8 Professional\LIBRARY for Proteus 8, or the matching Proteus 7 folder. Older versions keep it under ProgramData\Labcenter Electronics. If Proteus is open, close it first.

  3. 3

    Add the simulation model

    Copy TEPNET.DLL, TEPPCA9685.DLL and TEPROBOTARM.DLL and 7 more into the MODELS folder next to LIBRARY, so the component can run, not only be drawn.

  4. 4

    Restart Proteus and place the component

    Start Proteus, open a schematic, press P (Pick Devices) and search for the component by the name used in the tutorial. It appears with its pins ready to wire.

  5. 5

    Build the source code

    Open robot_arm.py, attr.py and color.py and 28 more in the compiler named in the tutorial (MikroC, Keil, MPLAB, Code Composer or the Arduino IDE) and build it to get the firmware.

  6. 6

    Open the example simulation

    Open Pi-5-Robot-Arm.pdsprj in Proteus to see the wiring exactly as in the tutorial. Check the controller's Program File path, then press Play.

  7. 7

    Follow the tutorial

    IoT Robot Arm Controller with Raspberry Pi 5 - Proteus Simulation explains every connection and setting in order; keep it open beside the files while you build.

How to add a library in Proteus 8

FAQs8 questionsContact TEP

How do I download IoT Robot Arm Controller with Raspberry Pi 5 - Proteus Simulation V1.0?

Wait for the 30-second guest countdown on this page, then press the download button; the file comes straight from our storage. Members who are logged in skip the wait. If the browser opens the file instead of saving it, use its Save as option. The download link is made for you when the countdown ends and works for 15 minutes; a saved or shared link stops working, so share this page instead.

What is inside the archive?

IoT Robot Arm Controller with Raspberry Pi 5 - Proteus Simulation V1.0 comes as a ZIP archive of 135 files (13.4 MB, 26.0 MB unpacked) holding Proteus library files, simulation model DLLs, a Proteus simulation, source code and a nested archive. Open the File Structure tab for the full list of 135 files.

What should I do if the download does not start?

Check the browser's download list first; an ad blocker or a company firewall can also hold it back, so try another browser or network. If the file arrives incomplete, download it again. For an installation problem, read the Install tab or tell us in the comments with your software version and the exact error message.

Is this file free?

Yes. Every file in the TEP Download Center is free for learning, personal and student projects. If you share it, link back to this page or the tutorial so others find the latest version.

How do I check that the file arrived complete?

Compare its SHA-256 with the one on this page, 7653497b6d8dd28f8a9596228750ebc39f6c046249f3280135dc3d14998c9fe1. In PowerShell run Get-FileHash "33120f3f8f9e4e9b9f12cb457b3ca52a.zip"; on macOS or Linux run shasum -a 256 "33120f3f8f9e4e9b9f12cb457b3ca52a.zip". The same value means the file is exactly the one in our storage; a different one means the download broke off, so download it again.

Do I need WinRAR to open the ZIP file?

No. Windows, macOS and Linux open ZIP archives on their own (Extract All, or double-click). WinRAR and 7-Zip work too. Extract the whole archive before using the files.

Where do I put the LIB and IDX files?

Both files go into the LIBRARY folder of your Proteus installation (Proteus 8: C:\Program Files (x86)\Labcenter Electronics\Proteus 8 Professional\LIBRARY; Proteus 7 has the same folder under its own name). Restart Proteus afterwards and search for the component with P.

Which Proteus version does the library need?

The tutorial names the Proteus version the library was made and tested with. Most TEP libraries work in Proteus 7 and Proteus 8; if the component does not appear after a restart, check that both the LIB and the IDX file were copied and that Proteus was fully closed while copying.

preparing · 33120f3f8f9e4e9b9f12cb457b3ca52a.zip
Rating
Your download will be ready shortly
Preparing your download…

Members skip the wait. Log in or join TEP.

Last 14 days0 downloads
SHA-256 7653497b6d8dd28f8a9596228750ebc39f6c046249f3280135dc3d14998c9fe1
DocumentationIoT Robot Arm Controller with Raspberry Pi 5 - Proteus Simulation
Need help with this file? Bug report Ask a question Download problemsGet updates
Advertisement

Comments

0

Join the conversation

Start the conversationAsk a question or share how you used this download.