Hello friends, hope you all are fine and having fun with your lives. Today, I am going to share an informational tutorial about top 10 PCB design Software. These PCB design software are used for designing PCBs. In all engineering projects especially related to electronics, PCB designing is an important task and in order to design the PCB we have to use some software. There are many software available in market and today, I am gonna give a complete list of PCB Design software.
Few of these software and free to use and few have limited versions available but in order to get their advanced features you have to buy them. I have also mentioned their features below. If you have read my blog in detail then must have the idea that I use Proteus software f ...
Hey Learners! I welcome you on the behalf of The Engineering Projects. I hope you are doing Great. If you are seeking for the best information about the T Flip Flop along with some small concepts and the Practical Performance, then you are at the right article. In this session you will get the following topics:
What are T Flip Flops?
What are the Functions of Preset and Clear Input in T Flip Flop?
How can we Design the Truth Table of T Flip Flop?
How can you perform the T Flip Flop simulation in very simple and useful way?
Moreover, you will also get some pieces of information in DID YOU KNOW sections. so without wasting time, lets Jump into the answer of 1st Question.
T Flip Flop
T Flip Flop belongs to the family of Flip Flops and Latche ...
Hello readers! I hope you are doing well. Today, we are going to explore the MC34063 buck converter library for Proteus. An MC34063 buck converter is a type of DC-DC power converter that steps down the high voltage to the low voltage. It’s a popular device to get lower DC volts because it provides a stable output. By default, Proteus software does not have the buck converter; therefore, I designed the library for the simulation of the projects with this converter. In this tutorial, I’ll discuss the basic introduction to Buck Converter and Proteus library installation, and will also share the most basic simulation to see how it works.
Introduction to the MC34063 Buck Converter
The Buck converter is a step-down DC-DC converter that decreases the voltages while increasing the current and pr ...
Hello friends, I hope you all are doing great. Today, I am going to share the Raspberry Pi 4 Library for Proteus. In our previous tutorial, we shared the Raspberry Pi 3 Library for Proteus and as we mentioned in that tutorial, these Raspberry Pi libraries will have dummy modules i.e. We have just designed the exterior but these boards won't be able to read the Python code. Although just for fun, we have added the Arduino firmware in these boards, so we can upload the Arduino code in it. As the legends say, something is better than nothing. We have given these boards an unofficial name "Arduino Pi".You can use these Pi boards to design your circuit diagram or can also use it in your presentation/demonstration of your projects. I hope you will enjoy these simulated Raspberry Pi boards. Befor ...
Hello friends, hope you all are having fun in your life.
Today's tutorial is about the component designing in Proteus ISIS. This tutorial actually deals with the presentation of your project. Usually when students give presentation of their projects, then it is asked that add the circuit diagram of their project. Now when students open Proteus in order to design their circuit, they found out that the components they have used in their project are not available in the Proteus Directory. Now what to do ?
In that case, there's a need to design your own component in Proteus and place it in the circuit. Although, this new designed component won't work as the real co ...
Hello friends, I hope you all are doing great. Today, I am going to share a new Infrared Tracker Sensor Library for Proteus. By using this library, you will be able to simulate IR based tracker sensor. This library contains 4 tracker sensors in it.
This Infrared Tracker Sensor is not present in Proteus software and we are sharing it for the first time. We have already shared 2 Proteus Libraries of Infrared sensors, you should check them as well.
Note:
You should also have a look at:
IR Proximity Sensor Library for Proteus.
Infrared Sensor Library for Proteus.
First, let's have a look at what is tracker sensor and why is it used?
What is IR Tracker Sensor???
IR Tracker Sensor uses Infrared technology and contains two IR LEDs on it. ...
Hello friends, I hope you all are doing great. In today's tutorial, I am going to share a new Rain Sensor Library for Proteus. I have got a lot of requests for designing this sensor. So finally it has been designed by our team and is ready to use in your Proteus Simulations.
Rain Sensor, as the name shows, is used for detection of rain and is common sensor used in Embedded Systems Projects. Both analog and digital rain sensors are available these days but we have only designed the digital Rain Sensor. It will give digital output and its output will be HIGH when there's rain and will remain LOW if it won't detect any rain.
As Proteus is a simulation software and we can't actually bring the rain so that's why I have placed a TestPin. If you apply H ...
Hey Pals! We hope you are doing Great. Today, we are going to design another application of DLD Logical Gates i.e. Half Subtractor. In our previous lectures, we covered Adders in detail, where we studied both Half Adders & Full Adders. Now its time to discuss its reciprocal i.e. Subtractors.
In this session, we'll seek the answers to the following topics:
What is Half Subtractor?
Working Principle of Half Subtractor.
Truth-table of Half Subtractor.
Simulation of Half Subtractor in Proteus using three Logic Gates.
Designing of Half Subtractor with NOR gate.
So, let's get started:
What is Subtractor?The functionality of Subtractors is exactly the opposite of Adders(we discussed in previous lectures) and defined as:A Subtractor is a simple DLD Electronic circuit, d ...
Hey Geeks! Welcome to The Engineering Projects. We hope you are doing great. MOSFET is a predominant component widely used in electronics due to its performance. We are working on the Projects of MOSFET and today's experiment is really interesting. We are working on the MOSFET Gate Driver and we will work on the following concepts:
Introduction to MOSFET Gate Driver.
Circuit of MOSFET Gate Driver.
Working of MOSFET Gate Driver.
Simulation of MOSFET Gate Driver in Proteus.
Applications of MOSFET Gate Driver.
You will find important information about the topic in DID YOU KNOW sections.
Introduction to MOSFET Gate Driver
We all know MOSFET is a type of transistor and is used in a wide range of circuits. It has many interesting features and ...
Hey pupils, welcome to The Engineering Projects. We hope you are doing great. In today's simulation in Proteus ISIS, we'll seek the knowledge of an interesting topic. We are going to design a Television remote jammer in Proteus. We all are familiar with the TV Remote controller device and know it works when a light signal emitted by it is sensed by the television. Have a glance at the topics we will see in detail today:
Introduction to 555 Timer TV Remote Control Jammer.
Components of the circuit.
Working principle of 555 Timer Jammer.
Simulation of the Jammer of TV Remote Control using 555 Timer.
Moreover, you will also learn some interesting facts about the topic in DID YOU KNOW sections. let's jump to our first topic.
555 Timer TV R ...
