Hello Guys! I welcome you on board. In this post today, I’ll document the detailed Introduction to 1n4744.
The 1n4744 is a Zener diode that comes with a total power dissipation of 1W. It is used in high-power rating circuits for clipping purposes. This component is composed of silicon material and comes with a forward voltage drop of 1.2V. This Zener diode is a bit different than a regular diode in terms of current conduction. The 1n4744 conducts in both directions i.e. forward-biased and reverse-biased conditions. While the regular diode conducts in forward-biased condition only. Zener diodes are also employed to prevent the electrical circuits from overvoltage.
Read the entire post as I’ll detail the datasheet, pinout, features, and applications of 1n4744. Keep reading.
Introduc ...
Hello friends, I hope you all are doing well. In today's tutorial, we are going to design a Home Security System using Arduino UNO in Proteus software. It's the most commonly designed engineering project, especially in electrical, electronics and mechatronics engineering. Normally engineering students design it as a semester project during their engineering course.
So, today we will design a home security system from scratch in Proteus software. I have given the complete project below to download but I would suggest you to design it on your own so that you could understand it better. So, let's get started:
Home Security System: Project Description
Before going into the detail, let's first download the complete Proteus Simulation with Ardui ...
Introduction
Hello friends, I hope you are doing very well. Today we are going to learn and practice the master control reset (MCR)! So what is that MCR? Well! This is a tool you might use to control a group of devices with one push button for performing fast emergency responses with one click for a group of devices in one zone. In another word, you divide the program into zones and put this zone between a master control to control their operation as one unit by one contact. This technique is useful for applying emergence stops and also protecting some equipment by applying a safety restriction to not operate when that condition is in effect.
The concept of the master control reset (MCR)
Figure 1 shows the master control relay in a ladder logic showing a couple of rungs between the ma ...
Hi friends, today we are going to learn a good technique to run multi outputs in sequence. In another word, when we have some output that is repeatedly run in sequence. In the normal or conventional technique of programming we deal with them individually or one by one which takes more effort in programming and much space of memory. So instead we can use a new technique to trigger these outputs in sequence using one instruction which will save the effort of programming and space of memory. In this article, we are going to introduce how to implement sequencer output instruction. And practice some examples with the simulator as usual. Before starting the article, we need to mention that, some controllers like Allen Bradley have sequencer output instruction and some has not like Siemens. So we ...
Hello friends, I hope you all are doing great. In today’s tutorial, we will have a look at the Introduction to 20x4 LCD Module. The LCD stands for liquid crystal display, which works on the light modulation features of liquid crystals. It is available in electronic visible display, video display and flat panel display. There are numerous categories and features are exist in markets of LCD and you can see it on your mobile, laptop, computer and television screen.
The invention of LCD gives new life to electronic industries and replaces lED and gas plasma techniques. It also replaces the CTR (cathode ray) tube that is used for visual display. The input power consumed by the liquid crystal display is less than the light-emitting diode and plasma display. In today's post, we will have a loo ...
Hello friends, I hope you all are doing great. In today's tutorial, I am going to share a new PC817 Library for Proteus. PC817 is an optocoupler / optoisolator, which is used for electrical isolation between components or modules. It's normally used after Microcontroller Pins so that back emf doesn't burn them. You should also have a look at Introduction to PC817, I have shared its complete details there.
PC817 is used a lot in Embedded projects but is not available in Proteus, so our team has designed it for the first time. Using this Library, now you can easily simulate this optocoupler in your Proteus simulations. So, let's get started with How to download & install PC817 Library for Proteus:
PC817 Library for Proteus
First of all, downl ...
Hello friends, I hope you all are doing fine. In today's tutorial, I am going to share a new Soil Moisture Sensor Library for Proteus V2.0. You should also have a look at its previous version i.e. Soil Moisture Sensor Library for Proteus V1.0. If you have worked on the previous version, it has only one soil moisture sensor in it, while in this library, we have added three soil moisture sensors.
First, we will have a brief introduction of the Soil Moisture sensor, then we will download the zip file containing Proteus Library files of Soil Moisture Sensor and finally, we will design a small simulation using these new sensors. So, let's get started:
What is Soil Moisture Sensor?
Soil Moisture sensor is an embedded sensor, used to measure the moist ...
Hey Everyone! I hope you are doing great. I am back to give you daily dose of information so you can excel in your life. Today, I am going to uncover the details on the Introduction to 5n50. It is an N-Channel MOSFET which is designed to obtain high switching performance and minimum on state resistance in an effective way. It is a unipolar device which comes with three terminals called drain gate and source. I'll try to cover everything in detail related to this N-Channel MOSFET. Let's hop on the board and dive in the details to unlock the features of this transistor.
Introduction to 5n50
5n50 is an N-Channel MOSFET that comes in advanced DMOS, planer stripe technology.
It is designed to achieve high switching performance. As it is an N-Chann ...
Hello everyone! hope you all will be fine. In this article I am going to share the knowledge about displaying Scrolling Text on LCD with Arduino. A Liquid Crystal Display is usually known as LCD in the market. It is a display unit made up of liquid crystal. When we want to made electronics based projects, we need a device on which we can show the system’s output and the desired messages. There are a lot of such devices which are helpful to display the output messages and the most common is a seven segment display.
Alternate good option is LCD, which are now available in different size having different qualities. 16×2 LCD Module is a most frequently used device for the electronic projects out of all the other types of LCD’s available in the marke ...
Hello friends, hope you all are enjoying and having fun. In today's tutorial we are gonna see how to design a LED Dimming Project using 555 Timer in Proteus ISIS. In our previous tutorials we have seen how to design Multiple LED Flasher Project using 555 Timer in Proteus ISIS and also Single and Double LED Flasher Project using 555 Timer in Proteus ISIS, in which we have seen how to flash Single and Multiple LED's using 555 Timer in Proteus ISIS. In today's post i am gonna extend the same concept and we will see how to design a LED Dimming Project Using 555 Timer in Proteus ISIS.
It is a quick and very simple tutorial and it elaborates how to control the Intensity of LED using 555 Timer in Proteus ISIS. It's a very simple project and the complete ...
