Hello friends, I hope you all are doing great. In today’s tutorial, we will have a look at What is Diode Clipper and how to use it in rectification circuits. In different circuits especially in rectifiers, the clipper is used to maintain the predefined voltage level. These circuits do not interrupt the original signal but only control the variation in the predefined value of the signal. These circuits eliminate the variation in the original waveform at the positive half and negative half.
These circuits are created by the combination of linear components such as resistance and non-linear components like transistors and diodes. These clipping circuits are also known as the slicers. In today's post, we will also have a look at such circuits that are ...
I hope you all are doing great. In today's tutorial, we are gonna have a look at detailed Introduction to ESP-01. ESP-01 is an inexpensive, small-sized WiFi module, which consists of TCP/IP stack along with a built-in microcontroller. So, we can directly program this small chip and can bring WiFi capability in our Embedded projects. When first time this ship came into the market in August 2014, it got a lot of attention by users. The main reason for it to seek attention is that this module allows the microcontroller to connect with a WiFi available (and programmed to connect) and it follows Hayes Style Commands and develops a TCP/IP network.
ESP-01 chip integrates an antenna, RF balun, power amplifier, filters, and power arrangement module. ESP-01 is used in industry and many projects a ...
Hello friends, I hope you all are doing great. In today's tutorial, we are gonna have a look at detailed Introduction to A1015. A1015 is a part of transmissive light sensing sequence which has a high competence GaAs Infrared light discharging diode which actions as the light stemming component, extremely sensitive phototransistor is used as the light sensing element. These two apparatuses are established so as in the opposite of each other, any materials fleeting among them are effortlessly sensed.
The A1015 is made in casing of TO-92. By seeing at its smooth side we can comprehend the three terminals impending out, these three terminals from left to right are emitter, collector and base. In today’s post, we will have a look at its fortification, ...
Hello friends, I hope you all are doing great. In today’s tutorial, we will discuss What is the Voltage Source. The source is a device that transformed thermal energy, chemical energy, mechanical energy or any type of energy in the electrical form of energy. We can say that the source is such an instrument manufactured for generating electrical power.
The voltage source has 2 endpoints by which it connects in the circuitry, the ideal voltage source gives the constant value of the voltage in a circuitry irrespective of the variation in the resistance of the output. While non-ideal voltage source cannot provide the same voltage to the circuitry during load variation. The voltage source is the correspondent of the current source. This eclectic source ...
Hello friends, I hope you all are doing great. In today's tutorial, we are gonna have a look at a detailed Introduction to TCS3200. TCS3200 is a color-detecting sensor, it consists of TAOS TCS3200 RGB sensor chip and four white LEDs. It is used to detect visible color in a measurable range. This sensor has an array of a photodetector diode, some diodes are equipped with different color filters i.e. red, blue or green color and some diodes do not have any filter.
TCS3200 has different applications such as test strip reading, sorting by color and ambient light sensing. In today's post, we will have a look at its working, protocol, pinout, specification, etc. I will also share some links where I have interfaced it with other microcontrollers. If you have any questions about it ask in the c ...
Hello friends, I hope you all are doing great. In today’s tutorial, we will discuss What is Full Wave Rectifier. Transformation of alternating current into the direct current is known as rectification. This conversion can be done by using a single diode or more than one diode. The diode that used for rectification is named as a rectifier. There are 2 main categories of the rectifiers, the first one is the half-wave and the other is full-wave rectifier.
In half-wave rectification circuitry, there is only single diode is used to convert alternating current into the direct current. So it can very easily design for rectification. But it has one drawback that it converts one half of the AC wave into direct current. Due to this, there is a higher power ...
Hello friends, I hope you all are doing great. In today's tutorial, we are gonna have a look at detailed Introduction to TIP41. It is an NPN power transistor. It exists in (TO-220) malleable suite which marks this expedient appropriate for acoustic, power rectilinear and swapping submissions. Its corresponding transistor is TIP42. It is intended by joining three (3) components of semiconductor material by doping with different materials. It's center portion is base which is tinny and the other two outer parts are prominently doped than the base.
Several transistors can strengthen a trivial current which will then be leading adequate to effort attention or other greater current maneuvers. These discretion are proficient to notice a shift in voltage ...
Hello friends, I hope you all are doing great. In today's tutorial, we are gonna have a look at detailed Introduction to 2sa1943. The 2sa1943 is a high power consuming PNP transistor, firstly it was created by a famous company Toshiba. As it has a high gain of current and consumes higher current at collector it is mostly used for such audio circuits which consume higher power or in AF amplifiers.
Nonetheless, currently the Transistor is outright from Toshiba and it has been swapped with TTA1943. We can also found old 2sa1943 in marketplaces because still it is replicated by other assemblers in China. In today’s post, we will have a look at its fortification, wreckages, implication, proposals, etc. I will also share some links where I have connecte ...
Hello friends, I hope you all are doing great. In today's tutorial, we are gonna have a look at detailed Introduction to TIP31. The TIP31 is a typical NPN transistor which is frequently cast-off for intermediate power submissions. This (BJT) is a three (3) points expedient which works for intensification or swapping submissions. It is designed by linking three units of semiconductors with alternatively dissimilar doping. The central unit which is (base) is thin and the other two external areas (emitter and collector) are greatly doped.
Some transistors can intensify a minor current which will then be dominant sufficient to work a spotlight or other higher current expedients. These diplomacies are also capable to notice an alteration in voltage an ...
Hello friends, I hope you all are doing great. In today's tutorial, we are gonna have a look at detailed Introduction to 74HC14. 74HC14 is a member of 74XXXX integrated circuit series, it consists of logic gates. This module is also called HEX Inverting Schmitt Trigger. It is available in six independent Schmitt trigger input inverters with standard push-pull outputs. The boolean function performed by this logic gates is Y=A. It is a 14 pin module which is available in various packages.
The 74HC14 works on the voltage range of 2.0V to 6.0V. This is a higher speed CMOS Schmitt Inverter mounted with a silicon gate C2MOS technology. In today's post, we will have a look at its pinout, construction, specifications, applications, working, etc. I will al ...
