TEP DOWNLOAD CENTER

Project Files of EMG Muscle-Controlled Gripper on Raspberry Pi 5 in Proteus Simulation

Libraries Code Projects Simulation
tep://download-terminal 464c6af4347e44e4b030bf13d82a49b2.zip ZIP archiveV1.0Verified0 downloadsFree
EMG Muscle-Controlled Gripper on Raspberry Pi 5 in Proteus Simulation: the Raspberry Pi 5, the EMG sensor, the ADS1115 and the DS3218 gripper servo
Proteus library · File 1 of 1

EMG Muscle-Controlled Gripper on Raspberry Pi 5 in Proteus Simulation V1.0

EMG Muscle-Controlled Gripper on Raspberry Pi 5 in Proteus Simulation V1.0 comes as a ZIP archive of 144 files (14.3 MB, 28.1 MB unpacked) holding Proteus library files, simulation model DLLs, a Proteus simulation, source code and a nested archive.

  • LIBProteus library
  • DLLProteus model
  • DSNProteus simulation
  • SRCSource code
  • ZIPNested archive

Description

EMG-Muscle-Controlled-Gripper-Raspberry-Pi-5-Proteus-Simulation-v1.0.zip: the complete Proteus simulation project (Raspberry Pi 5, the EMG muscle sensor, an ADS1115, the DS3218 servo, an LED, a resistor, the Laptop and Mobile WiFi Monitors), the Python program emg_gripper.py, every LIB and DLL the simulation needs, the TEPPi Python runtime and a README.

Read EMG Muscle-Controlled Gripper on Raspberry Pi 5 in Proteus Simulation

File Structure

464c6af4347e44e4b030bf13d82a49b2.zip144 files · 24 folders · 28.1 MB unpacked
Pi-5-EMG-Gripper-TEP-v1.0/144 files · 28.1 MB
Proteus Library Files/8 files · 569 KB
LIB TEPADS1115.LIBProteus library 66.3 KB
LIB TEPDS3218.LIBProteus library 25 KB
LIB TEPEMG.LIBProteus library 35.9 KB
LIB TEPLAPTOP.LIBProteus library 39.5 KB
LIB TEPLED5MM.LIBProteus library 21.8 KB
LIB TEPMOBILE.LIBProteus library 13.1 KB
LIB TEPRESISTOR.LIBProteus library 306.9 KB
LIB TEPRPI5.LIBProteus library 60.5 KB
Proteus Model Files/126 files · 23.0 MB
TEPPi/120 files · 18.7 MB
python/33 files · 17.5 MB
DLL libcrypto-3.dllSimulation model 3.3 MB
DLL libffi-8.dllSimulation model 34.3 KB
DLL libssl-3.dllSimulation model 620.8 KB
TXT LICENSE.txtText file 36 KB
PYD pyexpat.pydPYD file 169.8 KB
CAT python.catCAT file 628.1 KB
EXE python.exeEXE file 99.3 KB
DLL python3.dllSimulation model 65.3 KB
DLL python311.dllSimulation model 4.8 MB
ZIP python311.zipArchive 4.1 MB
_PTH python311._pth_PTH file 80 B
EXE pythonw.exeEXE file 97.8 KB
PYD select.pydPYD file 26.8 KB
DLL sqlite3.dllSimulation model 1.2 MB
PYD unicodedata.pydPYD file 1.1 MB
DLL vcruntime140.dllSimulation model 88.9 KB
PYD winsound.pydPYD file 27.3 KB
PYD _asyncio.pydPYD file 55.8 KB
PYD _bz2.pydPYD file 79.8 KB
PYD _ctypes.pydPYD file 105.8 KB
PYD _decimal.pydPYD file 193.8 KB
PYD _elementtree.pydPYD file 113.8 KB
PYD _hashlib.pydPYD file 48.8 KB
PYD _lzma.pydPYD file 145.8 KB
PYD _msi.pydPYD file 36.8 KB
PYD _multiprocessing.pydPYD file 29.3 KB
PYD _overlapped.pydPYD file 42.3 KB
PYD _queue.pydPYD file 28.8 KB
PYD _socket.pydPYD file 67.3 KB
PYD _sqlite3.pydPYD file 89.3 KB
PYD _ssl.pydPYD file 153.8 KB
PYD _uuid.pydPYD file 22.8 KB
PYD _zoneinfo.pydPYD file 38.8 KB
runtime/87 files · 1.1 MB
Adafruit_BBIO/6 files · 22.6 KB
PYC ADC.pycPYC file 2.1 KB
PYC GPIO.pycPYC file 9.9 KB
PYC PWM.pycPYC file 4.1 KB
PYC UART.pycPYC file 1.3 KB
PYC _pins.pycPYC file 4.7 KB
PYC __init__.pycPYC file 431 B
Adafruit_DHT/1 file · 2.5 KB
PYC __init__.pycPYC file 2.5 KB
arduino/2 files · 17.7 KB
app_utils/1 file · 17.5 KB
PYC __init__.pycPYC file 17.5 KB
PYC __init__.pycPYC file 283 B
colorzero/8 files · 85.3 KB
SRC attr.pySource file 6.5 KB
SRC color.pySource file 37.9 KB
SRC conversions.pySource file 11.1 KB
SRC deltae.pySource file 5.5 KB
SRC easings.pySource file 885 B
SRC tables.pySource file 13.6 KB
SRC types.pySource file 9 KB
SRC __init__.pySource file 878 B
colorzero-2.0.dist-info/5 files · 6.6 KB
TXT LICENSE.txtText file 1.5 KB
FILE METADATAFile 4 KB
FILE RECORDFile 1004 B
TXT top_level.txtText file 10 B
FILE WHEELFile 110 B
gpiozero/27 files · 594.5 KB
fonts/3 files · 12.6 KB
TXT 14seg.txtText file 2.6 KB
TXT 7seg.txtText file 1.1 KB
SRC __init__.pySource file 8.9 KB
pins/11 files · 234.3 KB
SRC data.pySource file 58.5 KB
SRC lgpio.pySource file 12.4 KB
SRC local.pySource file 6.6 KB
SRC mock.pySource file 18.5 KB
SRC native.pySource file 20.7 KB
SRC pi.pySource file 27.8 KB
SRC pigpio.pySource file 21.1 KB
SRC rpigpio.pySource file 7.1 KB
SRC spi.pySource file 7.7 KB
SRC style.pySource file 2.7 KB
SRC __init__.pySource file 51.2 KB
SRC boards.pySource file 100.9 KB
SRC compat.pySource file 1.2 KB
SRC devices.pySource file 24.3 KB
SRC exc.pySource file 7.4 KB
SRC input_devices.pySource file 53.6 KB
SRC internal_devices.pySource file 26.1 KB
SRC mixins.pySource file 20.5 KB
SRC output_devices.pySource file 60.5 KB
SRC spi_devices.pySource file 19.6 KB
SRC threads.pySource file 1.6 KB
SRC tones.pySource file 8.4 KB
SRC tools.pySource file 20.9 KB
SRC __init__.pySource file 2.6 KB
gpiozero-2.0.1.post3.dist-info/6 files · 14.6 KB
TXT entry_points.txtText file 539 B
RST LICENSE.rstRST file 1.4 KB
FILE METADATAFile 9.7 KB
FILE RECORDFile 2.8 KB
TXT top_level.txtText file 21 B
FILE WHEELFile 92 B
Jetson/2 files · 8.2 KB
GPIO/1 file · 7.9 KB
PYC __init__.pycPYC file 7.9 KB
PYC __init__.pycPYC file 264 B
micropython/11 files · 142.1 KB
PYC dht.pycPYC file 3.4 KB
PYC ds18x20.pycPYC file 3.8 KB
PYC framebuf.pycPYC file 17.5 KB
PYC machine.pycPYC file 55.2 KB
PYC micropython.pycPYC file 3.3 KB
PYC network.pycPYC file 10.8 KB
PYC ntptime.pycPYC file 1.5 KB
PYC onewire.pycPYC file 4.2 KB
PYC requests.pycPYC file 7.3 KB
PYC rp2.pycPYC file 2.5 KB
PYC tep_mpy.pycPYC file 32.6 KB
OPi/2 files · 14.8 KB
PYC GPIO.pycPYC file 14.5 KB
PYC __init__.pycPYC file 283 B
RPi/2 files · 17.6 KB
PYC GPIO.pycPYC file 17.4 KB
PYC __init__.pycPYC file 257 B
serial/2 files · 15.2 KB
PYC serialutil.pycPYC file 691 B
PYC __init__.pycPYC file 14.5 KB
smbus2/1 file · 12.8 KB
PYC __init__.pycPYC file 12.8 KB
PYC adafruit_dht.pycPYC file 3.6 KB
PYC board.pycPYC file 1.7 KB
PYC lgpio.pycPYC file 37 KB
PYC smbus.pycPYC file 418 B
PYC spidev.pycPYC file 6.2 KB
PYC tep_opi.pycPYC file 7 KB
PYC tep_pi.pycPYC file 37.3 KB
PYC tep_pi_boot.pycPYC file 10.6 KB
PYC tep_pi_fs.pycPYC file 23.7 KB
PYC tep_pi_net.pycPYC file 28.7 KB
PYC tep_pi_w1.pycPYC file 8.8 KB
PYC wiringpi.pycPYC file 16.9 KB
DLL TEPADS1115.DLLSimulation model 326 KB
DLL TEPDS3218.DLLSimulation model 296 KB
DLL TEPEMG.DLLSimulation model 315 KB
DLL TEPLED5MM.DLLSimulation model 289.5 KB
DLL TEPNET.DLLSimulation model 2.9 MB
DLL TEPRESISTOR.DLLSimulation model 311 KB
Proteus Simulation/8 files · 4.4 MB
SRC emg_gripper.pySource file 8.5 KB
DSN Pi-5-EMG-Gripper.pdsprjProteus simulation 41.6 KB
DLL TEPADS1115.DLLSimulation model 326 KB
DLL TEPDS3218.DLLSimulation model 296 KB
DLL TEPEMG.DLLSimulation model 315 KB
DLL TEPLED5MM.DLLSimulation model 289.5 KB
DLL TEPNET.DLLSimulation model 2.9 MB
DLL TEPRESISTOR.DLLSimulation model 311 KB
Python Code/1 file · 8.5 KB
SRC emg_gripper.pySource file 8.5 KB
TXT README.txtText file 10.3 KB

README

README.txt 144 lines
===============================================================================================================
  EMG Muscle-Controlled Gripper on Raspberry Pi 5 in Proteus Simulation - Project V1.0
  The Engineering Projects - www.TheEngineeringProjects.com
===============================================================================================================

IMPORTANT LINKS
  The project tutorial (circuit, code, simulation results):
    https://www.theengineeringprojects.com/2026/11/emg-muscle-controlled-gripper-raspberry-pi-5-proteus-simulation.html
  The libraries this project is built from (each post has its own full download and tutorial):
    Raspberry Pi 5 board:
      https://www.theengineeringprojects.com/2026/10/raspberry-pi-5-library-for-proteus.html
    EMG muscle sensor (MyoWare style):
      https://www.theengineeringprojects.com/2026/11/myoware-emg-muscle-sensor-library-for-proteus.html
    ADS1115 ADC:
      https://www.theengineeringprojects.com/2026/10/ads1115-adc-library-for-proteus-v1-0.html
    DS3218 servo motor:
      https://www.theengineeringprojects.com/2026/10/ds3218-servo-motor-library-for-proteus-v1-0.html
    5 mm LED:
      https://www.theengineeringprojects.com/2026/11/5mm-led-library-for-proteus.html
    Resistor:
      https://www.theengineeringprojects.com/2026/11/resistor-library-for-proteus.html
    Laptop WiFi Monitor:
      https://www.theengineeringprojects.com/2026/10/laptop-wifi-monitor-library-for-proteus.html
    Mobile WiFi Monitor:
      https://www.theengineeringprojects.com/2026/10/mobile-wifi-monitor-library-for-proteus.html
  Support our free work: https://www.theengineeringprojects.com/donate

FILE STRUCTURE
Pi-5-EMG-Gripper-TEP-v1.0/
|-- Proteus Library Files/
|   |-- TEPADS1115.LIB                                 66.3 KB   a part of the project -> LIBRARY folder
|   |-- TEPDS3218.LIB                                  25.0 KB   a part of the project -> LIBRARY folder
|   |-- TEPEMG.LIB                                     35.9 KB   a part of the project -> LIBRARY folder
|   |-- TEPLAPTOP.LIB                                  39.5 KB   a part of the project -> LIBRARY folder
|   |-- TEPLED5MM.LIB                                  21.8 KB   a part of the project -> LIBRARY folder
|   |-- TEPMOBILE.LIB                                  13.1 KB   a part of the project -> LIBRARY folder
|   |-- TEPRESISTOR.LIB                               306.9 KB   a part of the project -> LIBRARY folder
|   |-- TEPRPI5.LIB                                    60.5 KB   a part of the project -> LIBRARY folder
|-- Proteus Model Files/
|   |-- TEPADS1115.DLL                                326.0 KB   a model -> MODELS folder
|   |-- TEPDS3218.DLL                                 296.0 KB   a model -> MODELS folder
|   |-- TEPEMG.DLL                                    315.0 KB   a model -> MODELS folder
|   |-- TEPLED5MM.DLL                                 289.5 KB   a model -> MODELS folder
|   |-- TEPNET.DLL                                     2.89 MB   a model -> MODELS folder
|   |-- TEPRESISTOR.DLL                               311.0 KB   a model -> MODELS folder
|   |-- TEPPi/python/                                 17.54 MB   Python 3.11 embeddable -> MODELS\TEPPi (33 files)
|   |-- TEPPi/runtime/                                 1.11 MB   TEP Pi runtime, gpiozero -> MODELS\TEPPi (87 files)
|-- Proteus Simulation/
|   |-- emg_gripper.py                                  8.5 KB   the program PI1 runs
|   |-- Pi-5-EMG-Gripper.pdsprj                        41.6 KB   the project simulation
|   |-- TEPADS1115.DLL                                326.0 KB   copy of the model
|   |-- TEPDS3218.DLL                                 296.0 KB   copy of the model
|   |-- TEPEMG.DLL                                    315.0 KB   copy of the model
|   |-- TEPLED5MM.DLL                                 289.5 KB   copy of the model
|   |-- TEPNET.DLL                                     2.89 MB   copy of the model
|   |-- TEPRESISTOR.DLL                               311.0 KB   copy of the model
|-- Python Code/
|   |-- emg_gripper.py                                  8.5 KB   the program (the same file)
|-- README.txt                                        ~10.0 KB   this file
Total: 28.06 MB (unzipped). The C++ source code of the models is not included.

WHAT IS IT?
  A muscle-controlled robotic gripper you can run in Proteus: a Raspberry Pi 5 reads the EMG of a forearm muscle and
  closes a servo gripper in proportion to how hard the muscle contracts, the way a myoelectric prosthetic hand works;
  a web dashboard calibrates it and can lock the grip.
    * EMG muscle sensor (MUSCLEEMGTEP, U1): VIN on +3.3V, GND, ENV to A0 of the ADS1115; FLEX = the run's contractions
      (12-14 s 30 %, 17-20 s 60 %, 24-27 s 100 %, 30.5-31.3 s 80 %, 35-40 s 70 %, 46-48 s 50 %), GAIN 12.
    * ADS1115 (ADS1115ADVTEP, U2) on I2C1 at 0x48: VDD +3.3V, SDA GPIO2 (pin 3), SCL GPIO3 (pin 5), ADDR GND; A0 = ENV.
    * DS3218 servo (DS3218SERVOTEP, SERVO1), the gripper: SIG GPIO18 (pin 12), V+ on the 5 V rail, GND; START 30 (open).
    * Red LED LOCK (LED5MMREDTEP, D1) on GPIO23 (pin 16) through R1 220 ohm.
    * RASPBERRY PI 5 (PI1) runs emg_gripper.py on Ethernet at 192.168.1.51 (port 8000).
    * Laptop WiFi Monitor (PC1) and Mobile WiFi Monitor (MOB1) open http://192.168.1.51:8000/.
  The rules (at the top of the program):
    * the rest level: ENV averaged over the first 2 s (the muscle relaxed);
    * the strength = (ENV - rest) / (full - rest); a full contraction is 1.5 V until CAL records the strongest of 3 s;
    * proportional grip: a 10 % dead band, then 30 deg (open) to 150 deg (closed); each reading (20 a second) moves the
      grip 20 % of the way to its target; servo pulses 500 - 2500 us timed by the Pi (lgpio tx_servo);
    * a contraction starts above 15 % and ends below 10 %: its peak and length are logged;
    * LOCK holds the grip (the LED on) while the muscle relaxes; OPEN unlocks and opens the hand.
  Its pages:
    /          the dashboard: the controls, the strength, the grip, the calibration, the events
    /cal       record the full contraction (flex hard for 3 s)
    /lock      hold the grip / release it          /open      unlock and open the hand
    /data      everything as JSON
  No extra Python library: lgpio (in the TEPPi runtime and on Raspberry Pi OS), threading, http.server.

TEST STATUS
  Tested in Proteus 8 Professional on Windows 11, the run that made the tutorial's screenshots (the program's times):
  - 2.1 s: "rest level 0.014 V (the muscle relaxed)"; the gripper open at 30 deg.
  - 12 - 14 s, a 30 % contraction: ENV 0.44 - 0.56 V, the grip to 64 deg ("contraction 1: 41 % for 1.9 s", before CAL).
  - 17 - 20 s, 60 %: ENV about 1.0 V, the grip about 105 deg.
  - 24.0 s: CAL from the laptop during the full contraction (24 - 27 s): "CAL done: a full contraction is 2.086 V" at
    27.0 s; the gripper closed at 149.8 deg.
  - 35 - 40 s, 70 %: the grip about 91 deg; 37.1 s LOCK from the phone, "the grip held at 90 deg", the LED on; muscle
    relaxed at 40 s and the grip stayed at 89.5 deg.
  - 42.1 s: OPEN from the laptop; 46 - 48 s, 50 %: the grip to 71 deg - the muscle drives the hand again.
  - 6 contractions; 50.1 s of simulation in 459 s.

INSTALLATION
  1. Close Proteus. Extract the WHOLE zip file, for example to your Desktop.
  2. Copy the files from "Proteus Library Files" into the LIBRARY folder of Proteus, for example
     C:\Program Files (x86)\Labcenter Electronics\Proteus 8 Professional\LIBRARY
  3. Copy everything in "Proteus Model Files" - the DLL files and the TEPPi folder - into the MODELS folder (next
     to LIBRARY).
  4. Start Proteus. Press P in the schematic and search for RASPBERRY PI 5, MUSCLEEMGTEP or DS3218SERVOTEP to check that
     the parts are there.

RUN THE SIMULATION
  1. Open "Proteus Simulation\Pi-5-EMG-Gripper.pdsprj". Keep emg_gripper.py and the DLL files beside it.
  2. Press Play. Keep the muscle relaxed for the first 2 s (the first contraction comes at 12 s).
  3. The contractions come by themselves (U1's FLEX property): watch the gripper follow them.
  4. Open the Laptop WiFi Monitor (PC1) or the Mobile WiFi Monitor (MOB1) and press Go: CAL during a hard contraction,
     LOCK and OPEN.
  Your own contractions: edit U1's FLEX property ("start-end:percent, ..."). Your own program: edit emg_gripper.py.

PROPERTIES USED IN THIS PROJECT
  PI1 RASPBERRY PI 5           PROGRAM=emg_gripper.py, ETHERNET=IN (192.168.1.51)
  U1 MUSCLEEMGTEP              FLEX=12-14:30, 17-20:60, 24-27:100, 30.5-31.3:80, 35-40:70, 46-48:50
                               GAIN=12, NOISE=4, MAINS=50
  U2 ADS1115ADVTEP             (no changes)
  SERVO1 DS3218SERVOTEP        START=30, LOAD=0
  D1 LED5MMREDTEP, R1 220 ohm
  PC1, MOB1                    HOMEPAGE=http://192.168.1.51:8000/

TROUBLESHOOTING
  * The hand moves with a relaxed muscle: the rest level was taken during a contraction - restart relaxed.
  * The hand never closes fully: the full contraction is too high - CAL during a hard contraction.
  * The hand closes at a weak contraction: CAL was done with a weak one; do it again flexing hard.
  * The servo does not move: SIG not on GPIO18, or no 5 V on its V+.
  * The terminal cannot start Python: the TEPPi folder is not in MODELS.

LICENCES
  * The project, the program, the parts (LIB files) and the models (DLL files) are made by The Engineering Projects
    and are free for learning and for your own projects. The models use only standard Windows libraries.
    The C++ source code of the models is not included; the source code is not included for any model.
  * TEPPi\python is the Python 3.11 Windows embeddable package (Python Software Foundation License); TEPPi\runtime
    holds our TEP Pi runtime with gpiozero and colorzero (BSD licences) - their licence files are inside the folders.
  * Proteus is a product of Labcenter Electronics and is not included. Raspberry Pi is a trademark of Raspberry Pi
    Ltd; MyoWare is a trademark of Advancer Technologies; the ADS1115 is a product of Texas Instruments.
    This project is not made or endorsed by them. Not a medical device.

VERSION
  V1.0 - the first release of the project.
===============================================================================================================
Advertisement

Development1 release

  1. V1.0EMG Muscle-Controlled Gripper on Raspberry Pi 5 in Proteus Simulation V1.0this page

    V1.0 is the only release in the Download Center so far. When a newer version is published, it appears above with its own download page.

Installation7 steps

From the download to a working project, in order. The steps follow what the package contains.

You will need

  • Proteus Design SuiteProteus 8 or newer (Labcenter), on Windows
  • Pythonto build the source files into firmware
  • Any archive toolWindows, macOS and Linux extract ZIP files on their own

Steps

  1. 1

    Extract the archive

    Right-click 464c6af4347e44e4b030bf13d82a49b2.zip and choose Extract All (or open it with 7-Zip or WinRAR) into a folder you can find again. Keep its folder structure (Pi-5-EMG-Gripper-TEP-v1.0) as it is.

  2. 2

    Copy the library files into Proteus

    Move TEPADS1115.LIB, TEPDS3218.LIB and TEPEMG.LIB and 5 more and the files into the LIBRARY folder of your Proteus installation: C:\Program Files (x86)\Labcenter Electronics\Proteus 8 Professional\LIBRARY for Proteus 8, or the matching Proteus 7 folder. Older versions keep it under ProgramData\Labcenter Electronics. If Proteus is open, close it first.

  3. 3

    Add the simulation model

    Copy TEPADS1115.DLL, TEPDS3218.DLL and TEPEMG.DLL and 10 more into the MODELS folder next to LIBRARY, so the component can run, not only be drawn.

  4. 4

    Restart Proteus and place the component

    Start Proteus, open a schematic, press P (Pick Devices) and search for the component by the name used in the tutorial. It appears with its pins ready to wire.

  5. 5

    Build the source code

    Open emg_gripper.py, attr.py and color.py and 28 more in the compiler named in the tutorial (MikroC, Keil, MPLAB, Code Composer or the Arduino IDE) and build it to get the firmware.

  6. 6

    Open the example simulation

    Open Pi-5-EMG-Gripper.pdsprj in Proteus to see the wiring exactly as in the tutorial. Check the controller's Program File path, then press Play.

  7. 7

    Follow the tutorial

    EMG Muscle-Controlled Gripper on Raspberry Pi 5 in Proteus Simulation explains every connection and setting in order; keep it open beside the files while you build.

How to add a library in Proteus 8

FAQs8 questionsContact TEP

How do I download EMG Muscle-Controlled Gripper on Raspberry Pi 5 in Proteus Simulation V1.0?

Wait for the 30-second guest countdown on this page, then press the download button; the file comes straight from our storage. Members who are logged in skip the wait. If the browser opens the file instead of saving it, use its Save as option. The download link is made for you when the countdown ends and works for 15 minutes; a saved or shared link stops working, so share this page instead.

What is inside the archive?

EMG Muscle-Controlled Gripper on Raspberry Pi 5 in Proteus Simulation V1.0 comes as a ZIP archive of 144 files (14.3 MB, 28.1 MB unpacked) holding Proteus library files, simulation model DLLs, a Proteus simulation, source code and a nested archive. Open the File Structure tab for the full list of 144 files.

What should I do if the download does not start?

Check the browser's download list first; an ad blocker or a company firewall can also hold it back, so try another browser or network. If the file arrives incomplete, download it again. For an installation problem, read the Install tab or tell us in the comments with your software version and the exact error message.

Is this file free?

Yes. Every file in the TEP Download Center is free for learning, personal and student projects. If you share it, link back to this page or the tutorial so others find the latest version.

How do I check that the file arrived complete?

Compare its SHA-256 with the one on this page, e61cd875b702d968735fc1767beb66d33a5af096017f099f5e22771b39ebb05f. In PowerShell run Get-FileHash "464c6af4347e44e4b030bf13d82a49b2.zip"; on macOS or Linux run shasum -a 256 "464c6af4347e44e4b030bf13d82a49b2.zip". The same value means the file is exactly the one in our storage; a different one means the download broke off, so download it again.

Do I need WinRAR to open the ZIP file?

No. Windows, macOS and Linux open ZIP archives on their own (Extract All, or double-click). WinRAR and 7-Zip work too. Extract the whole archive before using the files.

Where do I put the LIB and IDX files?

Both files go into the LIBRARY folder of your Proteus installation (Proteus 8: C:\Program Files (x86)\Labcenter Electronics\Proteus 8 Professional\LIBRARY; Proteus 7 has the same folder under its own name). Restart Proteus afterwards and search for the component with P.

Which Proteus version does the library need?

The tutorial names the Proteus version the library was made and tested with. Most TEP libraries work in Proteus 7 and Proteus 8; if the component does not appear after a restart, check that both the LIB and the IDX file were copied and that Proteus was fully closed while copying.

preparing · 464c6af4347e44e4b030bf13d82a49b2.zip
Rating
Your download will be ready shortly
Preparing your download…

Members skip the wait. Log in or join TEP.

Last 14 days0 downloads
SHA-256 e61cd875b702d968735fc1767beb66d33a5af096017f099f5e22771b39ebb05f
DocumentationEMG Muscle-Controlled Gripper on Raspberry Pi 5 in Proteus Simulation
Need help with this file? Bug report Ask a question Download problemsGet updates
Advertisement

Comments

0

Join the conversation

Start the conversationAsk a question or share how you used this download.