TEP DOWNLOAD CENTER

Project Files of IoT AC Fan Speed Controller with Raspberry Pi 5 - Proteus Simulation

Libraries Code Projects Simulation
tep://download-terminal 5ba6598ca9534553be02cb654deb6b45.zip ZIP archiveV1.0Verified0 downloadsFree
IoT AC Fan Speed Controller with Raspberry Pi 5 - Proteus Simulation: the Raspberry Pi 5, the AC dimmer module, the 230 V fan, the mains source and the NTC on an ADS1115
Proteus library · File 1 of 1

IoT AC Fan Speed Controller with Raspberry Pi 5 - Proteus Simulation V1.0

IoT AC Fan Speed Controller with Raspberry Pi 5 - Proteus Simulation V1.0 comes as a ZIP archive of 144 files (14.3 MB, 28.0 MB unpacked) holding Proteus library files, simulation model DLLs, a Proteus simulation, source code and a nested archive.

  • LIBProteus library
  • DLLProteus model
  • DSNProteus simulation
  • SRCSource code
  • ZIPNested archive

Description

IoT-AC-Fan-Speed-Controller-Raspberry-Pi-5-Proteus-Simulation-v1.0.zip: the complete Proteus simulation project (Raspberry Pi 5, AC dimmer module, 120 mm 230 V AC fan, NTC thermistor, ADS1115, resistor, the Laptop and Mobile WiFi Monitors), the Python program ac_fan.py, every LIB and DLL the simulation needs, the TEPPi Python runtime and a README.

Read IoT AC Fan Speed Controller with Raspberry Pi 5 - Proteus Simulation

File Structure

5ba6598ca9534553be02cb654deb6b45.zip144 files · 24 folders · 28.0 MB unpacked
Pi-5-AC-Fan-Controller-TEP-v1.0/144 files · 28.0 MB
Proteus Library Files/8 files · 539.6 KB
LIB TEPACDIMMER.LIBProteus library 19.9 KB
LIB TEPACFAN120.LIBProteus library 19.2 KB
LIB TEPADS1115.LIBProteus library 66.3 KB
LIB TEPLAPTOP.LIBProteus library 39.5 KB
LIB TEPMOBILE.LIBProteus library 13.1 KB
LIB TEPNTC.LIBProteus library 14.3 KB
LIB TEPRESISTOR.LIBProteus library 306.9 KB
LIB TEPRPI5.LIBProteus library 60.5 KB
Proteus Model Files/126 files · 23.0 MB
TEPPi/120 files · 18.7 MB
python/33 files · 17.5 MB
DLL libcrypto-3.dllSimulation model 3.3 MB
DLL libffi-8.dllSimulation model 34.3 KB
DLL libssl-3.dllSimulation model 620.8 KB
TXT LICENSE.txtText file 36 KB
PYD pyexpat.pydPYD file 169.8 KB
CAT python.catCAT file 628.1 KB
EXE python.exeEXE file 99.3 KB
DLL python3.dllSimulation model 65.3 KB
DLL python311.dllSimulation model 4.8 MB
ZIP python311.zipArchive 4.1 MB
_PTH python311._pth_PTH file 80 B
EXE pythonw.exeEXE file 97.8 KB
PYD select.pydPYD file 26.8 KB
DLL sqlite3.dllSimulation model 1.2 MB
PYD unicodedata.pydPYD file 1.1 MB
DLL vcruntime140.dllSimulation model 88.9 KB
PYD winsound.pydPYD file 27.3 KB
PYD _asyncio.pydPYD file 55.8 KB
PYD _bz2.pydPYD file 79.8 KB
PYD _ctypes.pydPYD file 105.8 KB
PYD _decimal.pydPYD file 193.8 KB
PYD _elementtree.pydPYD file 113.8 KB
PYD _hashlib.pydPYD file 48.8 KB
PYD _lzma.pydPYD file 145.8 KB
PYD _msi.pydPYD file 36.8 KB
PYD _multiprocessing.pydPYD file 29.3 KB
PYD _overlapped.pydPYD file 42.3 KB
PYD _queue.pydPYD file 28.8 KB
PYD _socket.pydPYD file 67.3 KB
PYD _sqlite3.pydPYD file 89.3 KB
PYD _ssl.pydPYD file 153.8 KB
PYD _uuid.pydPYD file 22.8 KB
PYD _zoneinfo.pydPYD file 38.8 KB
runtime/87 files · 1.1 MB
Adafruit_BBIO/6 files · 22.6 KB
PYC ADC.pycPYC file 2.1 KB
PYC GPIO.pycPYC file 9.9 KB
PYC PWM.pycPYC file 4.1 KB
PYC UART.pycPYC file 1.3 KB
PYC _pins.pycPYC file 4.7 KB
PYC __init__.pycPYC file 431 B
Adafruit_DHT/1 file · 2.5 KB
PYC __init__.pycPYC file 2.5 KB
arduino/2 files · 17.7 KB
app_utils/1 file · 17.5 KB
PYC __init__.pycPYC file 17.5 KB
PYC __init__.pycPYC file 283 B
colorzero/8 files · 85.3 KB
SRC attr.pySource file 6.5 KB
SRC color.pySource file 37.9 KB
SRC conversions.pySource file 11.1 KB
SRC deltae.pySource file 5.5 KB
SRC easings.pySource file 885 B
SRC tables.pySource file 13.6 KB
SRC types.pySource file 9 KB
SRC __init__.pySource file 878 B
colorzero-2.0.dist-info/5 files · 6.6 KB
TXT LICENSE.txtText file 1.5 KB
FILE METADATAFile 4 KB
FILE RECORDFile 1004 B
TXT top_level.txtText file 10 B
FILE WHEELFile 110 B
gpiozero/27 files · 594.5 KB
fonts/3 files · 12.6 KB
TXT 14seg.txtText file 2.6 KB
TXT 7seg.txtText file 1.1 KB
SRC __init__.pySource file 8.9 KB
pins/11 files · 234.3 KB
SRC data.pySource file 58.5 KB
SRC lgpio.pySource file 12.4 KB
SRC local.pySource file 6.6 KB
SRC mock.pySource file 18.5 KB
SRC native.pySource file 20.7 KB
SRC pi.pySource file 27.8 KB
SRC pigpio.pySource file 21.1 KB
SRC rpigpio.pySource file 7.1 KB
SRC spi.pySource file 7.7 KB
SRC style.pySource file 2.7 KB
SRC __init__.pySource file 51.2 KB
SRC boards.pySource file 100.9 KB
SRC compat.pySource file 1.2 KB
SRC devices.pySource file 24.3 KB
SRC exc.pySource file 7.4 KB
SRC input_devices.pySource file 53.6 KB
SRC internal_devices.pySource file 26.1 KB
SRC mixins.pySource file 20.5 KB
SRC output_devices.pySource file 60.5 KB
SRC spi_devices.pySource file 19.6 KB
SRC threads.pySource file 1.6 KB
SRC tones.pySource file 8.4 KB
SRC tools.pySource file 20.9 KB
SRC __init__.pySource file 2.6 KB
gpiozero-2.0.1.post3.dist-info/6 files · 14.6 KB
TXT entry_points.txtText file 539 B
RST LICENSE.rstRST file 1.4 KB
FILE METADATAFile 9.7 KB
FILE RECORDFile 2.8 KB
TXT top_level.txtText file 21 B
FILE WHEELFile 92 B
Jetson/2 files · 8.2 KB
GPIO/1 file · 7.9 KB
PYC __init__.pycPYC file 7.9 KB
PYC __init__.pycPYC file 264 B
micropython/11 files · 142.1 KB
PYC dht.pycPYC file 3.4 KB
PYC ds18x20.pycPYC file 3.8 KB
PYC framebuf.pycPYC file 17.5 KB
PYC machine.pycPYC file 55.2 KB
PYC micropython.pycPYC file 3.3 KB
PYC network.pycPYC file 10.8 KB
PYC ntptime.pycPYC file 1.5 KB
PYC onewire.pycPYC file 4.2 KB
PYC requests.pycPYC file 7.3 KB
PYC rp2.pycPYC file 2.5 KB
PYC tep_mpy.pycPYC file 32.6 KB
OPi/2 files · 14.8 KB
PYC GPIO.pycPYC file 14.5 KB
PYC __init__.pycPYC file 283 B
RPi/2 files · 17.6 KB
PYC GPIO.pycPYC file 17.4 KB
PYC __init__.pycPYC file 257 B
serial/2 files · 15.2 KB
PYC serialutil.pycPYC file 691 B
PYC __init__.pycPYC file 14.5 KB
smbus2/1 file · 12.8 KB
PYC __init__.pycPYC file 12.8 KB
PYC adafruit_dht.pycPYC file 3.6 KB
PYC board.pycPYC file 1.7 KB
PYC lgpio.pycPYC file 37 KB
PYC smbus.pycPYC file 418 B
PYC spidev.pycPYC file 6.2 KB
PYC tep_opi.pycPYC file 7 KB
PYC tep_pi.pycPYC file 37.3 KB
PYC tep_pi_boot.pycPYC file 10.6 KB
PYC tep_pi_fs.pycPYC file 23.7 KB
PYC tep_pi_net.pycPYC file 28.7 KB
PYC tep_pi_w1.pycPYC file 8.8 KB
PYC wiringpi.pycPYC file 16.9 KB
DLL TEPACDIMMER.DLLSimulation model 296.5 KB
DLL TEPACFAN120.DLLSimulation model 291 KB
DLL TEPADS1115.DLLSimulation model 326 KB
DLL TEPNET.DLLSimulation model 2.9 MB
DLL TEPNTC.DLLSimulation model 288.5 KB
DLL TEPRESISTOR.DLLSimulation model 311 KB
Proteus Simulation/8 files · 4.4 MB
SRC ac_fan.pySource file 9 KB
DSN Pi-5-AC-Fan-Controller.pdsprjProteus simulation 38.7 KB
DLL TEPACDIMMER.DLLSimulation model 296.5 KB
DLL TEPACFAN120.DLLSimulation model 291 KB
DLL TEPADS1115.DLLSimulation model 326 KB
DLL TEPNET.DLLSimulation model 2.9 MB
DLL TEPNTC.DLLSimulation model 288.5 KB
DLL TEPRESISTOR.DLLSimulation model 311 KB
Python Code/1 file · 9 KB
SRC ac_fan.pySource file 9 KB
TXT README.txtText file 11 KB

README

README.txt 150 lines
===============================================================================================================
  IoT AC Fan Speed Controller with Raspberry Pi 5 - Proteus Simulation Project V1.0
  The Engineering Projects - www.TheEngineeringProjects.com
===============================================================================================================

IMPORTANT LINKS
  The project tutorial (circuit, code, simulation results):
    https://www.theengineeringprojects.com/2026/11/iot-ac-fan-speed-controller-raspberry-pi-5-proteus-simulation.html
  The libraries this project is built from (each post has its own full download and tutorial):
    Raspberry Pi 5 board:
      https://www.theengineeringprojects.com/2026/10/raspberry-pi-5-library-for-proteus.html
    AC dimmer module:
      https://www.theengineeringprojects.com/2026/11/ac-dimmer-module-library-for-proteus.html
    120 mm 230 V AC fan:
      https://www.theengineeringprojects.com/2026/11/120mm-230v-ac-fan-library-for-proteus.html
    NTC thermistor:
      https://www.theengineeringprojects.com/2026/11/ntc-thermistor-library-for-proteus.html
    ADS1115 ADC:
      https://www.theengineeringprojects.com/2026/10/ads1115-adc-library-for-proteus-v1-0.html
    Resistor:
      https://www.theengineeringprojects.com/2026/11/resistor-library-for-proteus.html
    Laptop WiFi Monitor:
      https://www.theengineeringprojects.com/2026/10/laptop-wifi-monitor-library-for-proteus.html
    Mobile WiFi Monitor:
      https://www.theengineeringprojects.com/2026/10/mobile-wifi-monitor-library-for-proteus.html
  Support our free work: https://www.theengineeringprojects.com/donate

FILE STRUCTURE
Pi-5-AC-Fan-Controller-TEP-v1.0/
|-- Proteus Library Files/
|   |-- TEPACDIMMER.LIB                                19.9 KB   a part of the project -> LIBRARY folder
|   |-- TEPACFAN120.LIB                                19.2 KB   a part of the project -> LIBRARY folder
|   |-- TEPADS1115.LIB                                 66.3 KB   a part of the project -> LIBRARY folder
|   |-- TEPLAPTOP.LIB                                  39.5 KB   a part of the project -> LIBRARY folder
|   |-- TEPMOBILE.LIB                                  13.1 KB   a part of the project -> LIBRARY folder
|   |-- TEPNTC.LIB                                     14.3 KB   a part of the project -> LIBRARY folder
|   |-- TEPRESISTOR.LIB                               306.9 KB   a part of the project -> LIBRARY folder
|   |-- TEPRPI5.LIB                                    60.5 KB   a part of the project -> LIBRARY folder
|-- Proteus Model Files/
|   |-- TEPACDIMMER.DLL                               296.5 KB   a model -> MODELS folder
|   |-- TEPACFAN120.DLL                               291.0 KB   a model -> MODELS folder
|   |-- TEPADS1115.DLL                                326.0 KB   a model -> MODELS folder
|   |-- TEPNET.DLL                                     2.89 MB   a model -> MODELS folder
|   |-- TEPNTC.DLL                                    288.5 KB   a model -> MODELS folder
|   |-- TEPRESISTOR.DLL                               311.0 KB   a model -> MODELS folder
|   |-- TEPPi/python/                                 17.54 MB   Python 3.11 embeddable -> MODELS\TEPPi (33 files)
|   |-- TEPPi/runtime/                                 1.11 MB   TEP Pi runtime, gpiozero -> MODELS\TEPPi (87 files)
|-- Proteus Simulation/
|   |-- ac_fan.py                                       9.0 KB   the program PI1 runs
|   |-- Pi-5-AC-Fan-Controller.pdsprj                  38.7 KB   the project simulation
|   |-- TEPACDIMMER.DLL                               296.5 KB   copy of the model
|   |-- TEPACFAN120.DLL                               291.0 KB   copy of the model
|   |-- TEPADS1115.DLL                                326.0 KB   copy of the model
|   |-- TEPNET.DLL                                     2.89 MB   copy of the model
|   |-- TEPNTC.DLL                                    288.5 KB   copy of the model
|   |-- TEPRESISTOR.DLL                               311.0 KB   copy of the model
|-- Python Code/
|   |-- ac_fan.py                                       9.0 KB   the program (the same file)
|-- README.txt                                        ~10.7 KB   this file
Total: 27.99 MB (unzipped). The C++ source code of the models is not included.

WHAT IS IT?
  An AC fan speed controller you can run in Proteus: a Raspberry Pi 5 sets the speed of a 230 V AC fan by
  phase-angle control through an AC dimmer module, follows the temperature of an NTC thermistor and serves a web
  dashboard.
    * AC dimmer module (DIMMERACTEP, U1): VCC on +5V, GND; Z-C (the zero-cross pulse) to GPIO17 (pin 11), PWM (the
      triac's gate) from GPIO27 (pin 13); L-IN on the mains' L, N-IN on the earthed neutral, L-OUT / N-OUT to the fan.
    * 120 mm 230 V AC fan (FAN120ACTEP, M1) on the dimmer's output.
    * V1 = Proteus's own ALTERNATOR: 325 V peak (230 V RMS), 50 Hz - the mains.
    * NTC thermistor 10 k bead, B 3950 (NTCBEAD10KTEP, RT1) from the net NTC to GND, R1 10 k from +3.3V to NTC.
    * ADS1115 (ADS1115ADVTEP, U2) on I2C1 at 0x48 (ADDR to GND): VDD +3.3V, SDA GPIO2 (pin 3), SCL GPIO3 (pin 5),
      A0 = the net NTC. The Pi has no analog input.
    * RASPBERRY PI 5 (PI1) runs ac_fan.py on Ethernet at 192.168.1.51 (port 8000).
    * Laptop WiFi Monitor (PC1) and Mobile WiFi Monitor (MOB1) open http://192.168.1.51:8000/.
  The rules (at the top of the program):
    * every half cycle of the mains the triac is fired a delay after the zero; it conducts to the next zero. The
      delay for a power share P solves 1 - a/pi + sin(2a)/(2 pi) = P (a = the firing angle), 0.6 - 9.0 ms;
    * the Z-C pulse rises about 0.5 ms before the real zero: the program adds 0.51 ms;
    * the gate is held high to 8.5 ms after the zero: a fan's current lags its voltage, and a short pulse that comes
      while the triac still carries the last half cycle's current is missed;
    * the mains' frequency is measured from the zero crosses (100 a second at 50 Hz);
    * AUTO: OFF below 24 C, 30 % at 24 C rising to 100 % at 36 C;
    * the temperature: R(NTC) = 10 k x V / (3.3 - V), then the Beta equation from 25 C (B 3950).
  Its pages:
    /            the dashboard: the controls, the temperature, the power, the firing delay, the mains, the events
    /auto        AUTO: the power follows the temperature
    /off  /p30  /p60  /p100    OFF or a fixed power
    /data        everything as JSON
  No extra Python library: lgpio (in the TEPPi runtime and on Raspberry Pi OS), math, threading, http.server.

TEST STATUS
  Tested in Proteus 8 Professional on Windows 11, the run that made the tutorial's screenshots (the program's times):
  - 0 - 12 s: 22.0 C, AUTO: the fan off; the mains measured from the zero crosses: 50.00 Hz; the Z-C pulse 1.03 ms
    wide, rising 0.51 ms before each zero.
  - 12.4 s: the NTC's air +10 C (32 C); the bead follows (7 s time constant). 13.3 s: "AUTO: 24.2 C - the fan 31 %,
    fired 6.0 ms after the zero"; at 15 s the dimmer fires at 5.38 ms (97 deg), 153 V RMS, and the fan starts (254 RPM).
  - 26 s: about 30.8 C, AUTO near 69 %: fired 4.08 ms (73 deg), 195 V, 0.094 A, 13.2 W; the fan 2337 RPM, 141 m3/h.
  - 28.3 s: 100 % from the phone: fired at 0.6 ms - the triac turns on at 2.53 ms (45 deg), where the fan's lagging
    current ends, and carries the whole cycle (the gate held to 8.5 ms): 229 V, 0.115 A, 18.7 W, 2639 RPM, 159 m3/h.
  - 34.5 s: 30 % from the laptop: fired 6.08 ms (109 deg), 128 V, 0.064 A, 5.5 W; 1009 RPM, 61 m3/h.
  - 41.8 s: OFF: no firing, the fan coasting (231 RPM at 45 s). 46.4 s: AUTO again: 32.1 C, 77 %, fired 3.5 ms.
  - 52 s: the air back to Room 25: the fan slows with the temperature (70 % at 30.9 C, 53 % at 27.9 C, 42 % at 26.1 C);
    at 66 s, 25.9 C: fired 5.48 ms (99 deg), 150 V, 0.076 A, 8.0 W, 1483 RPM, 89 m3/h.
  - 69.6 s of simulation in 450 s; the NTC 9.70 kohm at 25.7 C at the end (self-heating 0.14 C).

INSTALLATION
  1. Close Proteus. Extract the WHOLE zip file, for example to your Desktop.
  2. Copy the files from "Proteus Library Files" into the LIBRARY folder of Proteus, for example
     C:\Program Files (x86)\Labcenter Electronics\Proteus 8 Professional\LIBRARY
  3. Copy everything in "Proteus Model Files" - the DLL files and the TEPPi folder - into the MODELS folder (next
     to LIBRARY).
  4. Start Proteus. Press P in the schematic and search for RASPBERRY PI 5, DIMMERACTEP or FAN120ACTEP to check that
     the parts are there.

RUN THE SIMULATION
  1. Open "Proteus Simulation\Pi-5-AC-Fan-Controller.pdsprj". Keep ac_fan.py and the DLL files beside it.
  2. Press Play. The Pi's terminal opens; the NTC starts at 22 C, so AUTO keeps the fan off.
  3. Click a lead of RT1 for its pop-up and warm the air (+10 C, Hot 60, or hold the mouse on the bead: a finger).
  4. Open the Laptop WiFi Monitor (PC1) or the Mobile WiFi Monitor (MOB1), press Go and try 30 %, 60 %, 100 %, OFF
     and AUTO. Watch the fan's and the dimmer's pop-ups.
  Your own program: edit ac_fan.py beside the project (PI1's PROGRAM property) and press Play again.

PROPERTIES USED IN THIS PROJECT
  PI1 RASPBERRY PI 5           PROGRAM=ac_fan.py, ETHERNET=IN (192.168.1.51)
  V1 ALTERNATOR                AMP=325V, FREQ=50Hz
  RT1 NTCBEAD10KTEP            VALUE=10k, AIR=22 (the air at the start, C)
  R1 RESISTOR4BANDTEP          10k
  U1, M1, U2                   (no changes)
  PC1, MOB1                    HOMEPAGE=http://192.168.1.51:8000/

TROUBLESHOOTING
  * The fan never starts: no zero-cross pulses on GPIO17 (the dimmer's VCC), or the mains source missing.
  * The fan runs at full speed whatever the setting: the gate held high - the delay must come after each zero.
  * The fan stutters at high power: the gate pulse too short for a lagging current - hold it to 8.5 ms.
  * The temperature reads "-": the NTC divider open or shorted, or the ADS1115 not at 0x48.
  * The terminal cannot start Python: the TEPPi folder is not in MODELS.
  * On a real board: the dimmer and the fan carry MAINS VOLTAGE. Never touch them while plugged in; use an enclosure.

LICENCES
  * The project, the program, the parts (LIB files) and the models (DLL files) are made by The Engineering Projects
    and are free for learning and for your own projects. The models use only standard Windows libraries.
    The C++ source code of the models is not included; the source code is not included for any model.
  * TEPPi\python is the Python 3.11 Windows embeddable package (Python Software Foundation License); TEPPi\runtime
    holds our TEP Pi runtime with gpiozero and colorzero (BSD licences) - their licence files are inside the folders.
  * Proteus and its ALTERNATOR are products of Labcenter Electronics and are not included. Raspberry Pi is a trademark
    of Raspberry Pi Ltd; ADS1115 is a product of Texas Instruments. This project is not made or endorsed by them.

VERSION
  V1.0 - the first release of the project.
===============================================================================================================
Advertisement

Development1 release

  1. V1.0IoT AC Fan Speed Controller with Raspberry Pi 5 - Proteus Simulation V1.0this page

    V1.0 is the only release in the Download Center so far. When a newer version is published, it appears above with its own download page.

Installation7 steps

From the download to a working project, in order. The steps follow what the package contains.

You will need

  • Proteus Design SuiteProteus 8 or newer (Labcenter), on Windows
  • Pythonto build the source files into firmware
  • Any archive toolWindows, macOS and Linux extract ZIP files on their own

Steps

  1. 1

    Extract the archive

    Right-click 5ba6598ca9534553be02cb654deb6b45.zip and choose Extract All (or open it with 7-Zip or WinRAR) into a folder you can find again. Keep its folder structure (Pi-5-AC-Fan-Controller-TEP-v1.0) as it is.

  2. 2

    Copy the library files into Proteus

    Move TEPACDIMMER.LIB, TEPACFAN120.LIB and TEPADS1115.LIB and 5 more and the files into the LIBRARY folder of your Proteus installation: C:\Program Files (x86)\Labcenter Electronics\Proteus 8 Professional\LIBRARY for Proteus 8, or the matching Proteus 7 folder. Older versions keep it under ProgramData\Labcenter Electronics. If Proteus is open, close it first.

  3. 3

    Add the simulation model

    Copy TEPACDIMMER.DLL, TEPACFAN120.DLL and TEPADS1115.DLL and 10 more into the MODELS folder next to LIBRARY, so the component can run, not only be drawn.

  4. 4

    Restart Proteus and place the component

    Start Proteus, open a schematic, press P (Pick Devices) and search for the component by the name used in the tutorial. It appears with its pins ready to wire.

  5. 5

    Build the source code

    Open ac_fan.py, attr.py and color.py and 28 more in the compiler named in the tutorial (MikroC, Keil, MPLAB, Code Composer or the Arduino IDE) and build it to get the firmware.

  6. 6

    Open the example simulation

    Open Pi-5-AC-Fan-Controller.pdsprj in Proteus to see the wiring exactly as in the tutorial. Check the controller's Program File path, then press Play.

  7. 7

    Follow the tutorial

    IoT AC Fan Speed Controller with Raspberry Pi 5 - Proteus Simulation explains every connection and setting in order; keep it open beside the files while you build.

How to add a library in Proteus 8

FAQs8 questionsContact TEP

How do I download IoT AC Fan Speed Controller with Raspberry Pi 5 - Proteus Simulation V1.0?

Wait for the 30-second guest countdown on this page, then press the download button; the file comes straight from our storage. Members who are logged in skip the wait. If the browser opens the file instead of saving it, use its Save as option. The download link is made for you when the countdown ends and works for 15 minutes; a saved or shared link stops working, so share this page instead.

What is inside the archive?

IoT AC Fan Speed Controller with Raspberry Pi 5 - Proteus Simulation V1.0 comes as a ZIP archive of 144 files (14.3 MB, 28.0 MB unpacked) holding Proteus library files, simulation model DLLs, a Proteus simulation, source code and a nested archive. Open the File Structure tab for the full list of 144 files.

What should I do if the download does not start?

Check the browser's download list first; an ad blocker or a company firewall can also hold it back, so try another browser or network. If the file arrives incomplete, download it again. For an installation problem, read the Install tab or tell us in the comments with your software version and the exact error message.

Is this file free?

Yes. Every file in the TEP Download Center is free for learning, personal and student projects. If you share it, link back to this page or the tutorial so others find the latest version.

How do I check that the file arrived complete?

Compare its SHA-256 with the one on this page, f2593d409f36914bf988b0412f0f7fc9f3e0d81059eceaa2d2d8e78535d7d63c. In PowerShell run Get-FileHash "5ba6598ca9534553be02cb654deb6b45.zip"; on macOS or Linux run shasum -a 256 "5ba6598ca9534553be02cb654deb6b45.zip". The same value means the file is exactly the one in our storage; a different one means the download broke off, so download it again.

Do I need WinRAR to open the ZIP file?

No. Windows, macOS and Linux open ZIP archives on their own (Extract All, or double-click). WinRAR and 7-Zip work too. Extract the whole archive before using the files.

Where do I put the LIB and IDX files?

Both files go into the LIBRARY folder of your Proteus installation (Proteus 8: C:\Program Files (x86)\Labcenter Electronics\Proteus 8 Professional\LIBRARY; Proteus 7 has the same folder under its own name). Restart Proteus afterwards and search for the component with P.

Which Proteus version does the library need?

The tutorial names the Proteus version the library was made and tested with. Most TEP libraries work in Proteus 7 and Proteus 8; if the component does not appear after a restart, check that both the LIB and the IDX file were copied and that Proteus was fully closed while copying.

preparing · 5ba6598ca9534553be02cb654deb6b45.zip
Rating
Your download will be ready shortly
Preparing your download…

Members skip the wait. Log in or join TEP.

Last 14 days0 downloads
SHA-256 f2593d409f36914bf988b0412f0f7fc9f3e0d81059eceaa2d2d8e78535d7d63c
DocumentationIoT AC Fan Speed Controller with Raspberry Pi 5 - Proteus Simulation
Need help with this file? Bug report Ask a question Download problemsGet updates
Advertisement

Comments

0

Join the conversation

Start the conversationAsk a question or share how you used this download.