TEP DOWNLOAD CENTER

Project Files of IoT Split-Flap Message Board with Raspberry Pi 5 - Proteus Simulation

Libraries Code Projects Simulation
tep://download-terminal 90ea3659beb1432ab63b0651544b7476.zip ZIP archiveV1.0Verified0 downloadsFree
IoT Split-Flap Message Board with Raspberry Pi 5 - Proteus Simulation: the Raspberry Pi 5, four ULN2003 boards and four split-flap modules
Proteus library · File 1 of 1

IoT Split-Flap Message Board with Raspberry Pi 5 - Proteus Simulation V1.0

IoT Split-Flap Message Board with Raspberry Pi 5 - Proteus Simulation V1.0 comes as a ZIP archive of 135 files (13.3 MB, 25.9 MB unpacked) holding Proteus library files, simulation model DLLs, a Proteus simulation, source code and a nested archive.

  • LIBProteus library
  • DLLProteus model
  • DSNProteus simulation
  • SRCSource code
  • ZIPNested archive

Description

IoT-Split-Flap-Message-Board-Raspberry-Pi-5-Proteus-Simulation-v1.0.zip: the complete Proteus simulation project (Raspberry Pi 5, four split-flap modules, four ULN2003 boards, the Laptop and Mobile WiFi Monitors), the Python program splitflap_board.py, every LIB and DLL the simulation needs, the TEPPi Python runtime and a README.

Read IoT Split-Flap Message Board with Raspberry Pi 5 - Proteus Simulation

File Structure

90ea3659beb1432ab63b0651544b7476.zip135 files · 24 folders · 25.9 MB unpacked
Pi-5-Split-Flap-Message-Board-TEP-v1.0/135 files · 25.9 MB
Proteus Library Files/5 files · 223.2 KB
LIB TEPLAPTOP.LIBProteus library 39.5 KB
LIB TEPMOBILE.LIBProteus library 13.1 KB
LIB TEPRPI5.LIBProteus library 60.5 KB
LIB TEPSPLITFLAP.LIBProteus library 20.5 KB
LIB TEPULN2003.LIBProteus library 89.7 KB
Proteus Model Files/123 files · 22.1 MB
TEPPi/120 files · 18.7 MB
python/33 files · 17.5 MB
DLL libcrypto-3.dllSimulation model 3.3 MB
DLL libffi-8.dllSimulation model 34.3 KB
DLL libssl-3.dllSimulation model 620.8 KB
TXT LICENSE.txtText file 36 KB
PYD pyexpat.pydPYD file 169.8 KB
CAT python.catCAT file 628.1 KB
EXE python.exeEXE file 99.3 KB
DLL python3.dllSimulation model 65.3 KB
DLL python311.dllSimulation model 4.8 MB
ZIP python311.zipArchive 4.1 MB
_PTH python311._pth_PTH file 80 B
EXE pythonw.exeEXE file 97.8 KB
PYD select.pydPYD file 26.8 KB
DLL sqlite3.dllSimulation model 1.2 MB
PYD unicodedata.pydPYD file 1.1 MB
DLL vcruntime140.dllSimulation model 88.9 KB
PYD winsound.pydPYD file 27.3 KB
PYD _asyncio.pydPYD file 55.8 KB
PYD _bz2.pydPYD file 79.8 KB
PYD _ctypes.pydPYD file 105.8 KB
PYD _decimal.pydPYD file 193.8 KB
PYD _elementtree.pydPYD file 113.8 KB
PYD _hashlib.pydPYD file 48.8 KB
PYD _lzma.pydPYD file 145.8 KB
PYD _msi.pydPYD file 36.8 KB
PYD _multiprocessing.pydPYD file 29.3 KB
PYD _overlapped.pydPYD file 42.3 KB
PYD _queue.pydPYD file 28.8 KB
PYD _socket.pydPYD file 67.3 KB
PYD _sqlite3.pydPYD file 89.3 KB
PYD _ssl.pydPYD file 153.8 KB
PYD _uuid.pydPYD file 22.8 KB
PYD _zoneinfo.pydPYD file 38.8 KB
runtime/87 files · 1.1 MB
Adafruit_BBIO/6 files · 22.6 KB
PYC ADC.pycPYC file 2.1 KB
PYC GPIO.pycPYC file 9.9 KB
PYC PWM.pycPYC file 4.1 KB
PYC UART.pycPYC file 1.3 KB
PYC _pins.pycPYC file 4.7 KB
PYC __init__.pycPYC file 431 B
Adafruit_DHT/1 file · 2.5 KB
PYC __init__.pycPYC file 2.5 KB
arduino/2 files · 17.7 KB
app_utils/1 file · 17.5 KB
PYC __init__.pycPYC file 17.5 KB
PYC __init__.pycPYC file 283 B
colorzero/8 files · 85.3 KB
SRC attr.pySource file 6.5 KB
SRC color.pySource file 37.9 KB
SRC conversions.pySource file 11.1 KB
SRC deltae.pySource file 5.5 KB
SRC easings.pySource file 885 B
SRC tables.pySource file 13.6 KB
SRC types.pySource file 9 KB
SRC __init__.pySource file 878 B
colorzero-2.0.dist-info/5 files · 6.6 KB
TXT LICENSE.txtText file 1.5 KB
FILE METADATAFile 4 KB
FILE RECORDFile 1004 B
TXT top_level.txtText file 10 B
FILE WHEELFile 110 B
gpiozero/27 files · 594.5 KB
fonts/3 files · 12.6 KB
TXT 14seg.txtText file 2.6 KB
TXT 7seg.txtText file 1.1 KB
SRC __init__.pySource file 8.9 KB
pins/11 files · 234.3 KB
SRC data.pySource file 58.5 KB
SRC lgpio.pySource file 12.4 KB
SRC local.pySource file 6.6 KB
SRC mock.pySource file 18.5 KB
SRC native.pySource file 20.7 KB
SRC pi.pySource file 27.8 KB
SRC pigpio.pySource file 21.1 KB
SRC rpigpio.pySource file 7.1 KB
SRC spi.pySource file 7.7 KB
SRC style.pySource file 2.7 KB
SRC __init__.pySource file 51.2 KB
SRC boards.pySource file 100.9 KB
SRC compat.pySource file 1.2 KB
SRC devices.pySource file 24.3 KB
SRC exc.pySource file 7.4 KB
SRC input_devices.pySource file 53.6 KB
SRC internal_devices.pySource file 26.1 KB
SRC mixins.pySource file 20.5 KB
SRC output_devices.pySource file 60.5 KB
SRC spi_devices.pySource file 19.6 KB
SRC threads.pySource file 1.6 KB
SRC tones.pySource file 8.4 KB
SRC tools.pySource file 20.9 KB
SRC __init__.pySource file 2.6 KB
gpiozero-2.0.1.post3.dist-info/6 files · 14.6 KB
TXT entry_points.txtText file 539 B
RST LICENSE.rstRST file 1.4 KB
FILE METADATAFile 9.7 KB
FILE RECORDFile 2.8 KB
TXT top_level.txtText file 21 B
FILE WHEELFile 92 B
Jetson/2 files · 8.2 KB
GPIO/1 file · 7.9 KB
PYC __init__.pycPYC file 7.9 KB
PYC __init__.pycPYC file 264 B
micropython/11 files · 142.1 KB
PYC dht.pycPYC file 3.4 KB
PYC ds18x20.pycPYC file 3.8 KB
PYC framebuf.pycPYC file 17.5 KB
PYC machine.pycPYC file 55.2 KB
PYC micropython.pycPYC file 3.3 KB
PYC network.pycPYC file 10.8 KB
PYC ntptime.pycPYC file 1.5 KB
PYC onewire.pycPYC file 4.2 KB
PYC requests.pycPYC file 7.3 KB
PYC rp2.pycPYC file 2.5 KB
PYC tep_mpy.pycPYC file 32.6 KB
OPi/2 files · 14.8 KB
PYC GPIO.pycPYC file 14.5 KB
PYC __init__.pycPYC file 283 B
RPi/2 files · 17.6 KB
PYC GPIO.pycPYC file 17.4 KB
PYC __init__.pycPYC file 257 B
serial/2 files · 15.2 KB
PYC serialutil.pycPYC file 691 B
PYC __init__.pycPYC file 14.5 KB
smbus2/1 file · 12.8 KB
PYC __init__.pycPYC file 12.8 KB
PYC adafruit_dht.pycPYC file 3.6 KB
PYC board.pycPYC file 1.7 KB
PYC lgpio.pycPYC file 37 KB
PYC smbus.pycPYC file 418 B
PYC spidev.pycPYC file 6.2 KB
PYC tep_opi.pycPYC file 7 KB
PYC tep_pi.pycPYC file 37.3 KB
PYC tep_pi_boot.pycPYC file 10.6 KB
PYC tep_pi_fs.pycPYC file 23.7 KB
PYC tep_pi_net.pycPYC file 28.7 KB
PYC tep_pi_w1.pycPYC file 8.8 KB
PYC wiringpi.pycPYC file 16.9 KB
DLL TEPNET.DLLSimulation model 2.9 MB
DLL TEPSPLITFLAP.DLLSimulation model 290.5 KB
DLL TEPULN2003.DLLSimulation model 308 KB
Proteus Simulation/5 files · 3.5 MB
DSN Pi-5-Split-Flap-Message-Board.pdsprjProteus simulation 32.6 KB
SRC splitflap_board.pySource file 10.6 KB
DLL TEPNET.DLLSimulation model 2.9 MB
DLL TEPSPLITFLAP.DLLSimulation model 290.5 KB
DLL TEPULN2003.DLLSimulation model 308 KB
Python Code/1 file · 10.6 KB
SRC splitflap_board.pySource file 10.6 KB
TXT README.txtText file 9.4 KB

README

README.txt 130 lines
===============================================================================================================
  IoT Split-Flap Message Board with Raspberry Pi 5 - Proteus Simulation Project V1.0
  The Engineering Projects - www.TheEngineeringProjects.com
===============================================================================================================

IMPORTANT LINKS
  The project tutorial (circuit, code, simulation results):
    https://www.theengineeringprojects.com/2026/11/iot-split-flap-message-board-raspberry-pi-5-proteus-simulation.html
  The libraries this project is built from (each post has its own full download and tutorial):
    Raspberry Pi 5 board:
      https://www.theengineeringprojects.com/2026/10/raspberry-pi-5-library-for-proteus.html
    Split-flap display module:
      https://www.theengineeringprojects.com/2026/11/split-flap-display-library-for-proteus-v1-0.html
    28BYJ-48 stepper and ULN2003 driver board:
      https://www.theengineeringprojects.com/2026/10/28byj-48-uln2003-stepper-motor-library-for-proteus-v1-0.html
    Laptop WiFi Monitor:
      https://www.theengineeringprojects.com/2026/10/laptop-wifi-monitor-library-for-proteus.html
    Mobile WiFi Monitor:
      https://www.theengineeringprojects.com/2026/10/mobile-wifi-monitor-library-for-proteus.html
  Support our free work: https://www.theengineeringprojects.com/donate

FILE STRUCTURE
Pi-5-Split-Flap-Message-Board-TEP-v1.0/
|-- Proteus Library Files/
|   |-- TEPLAPTOP.LIB                                  39.5 KB   a part of the project -> LIBRARY folder
|   |-- TEPMOBILE.LIB                                  13.1 KB   a part of the project -> LIBRARY folder
|   |-- TEPRPI5.LIB                                    60.5 KB   a part of the project -> LIBRARY folder
|   |-- TEPSPLITFLAP.LIB                               20.5 KB   a part of the project -> LIBRARY folder
|   |-- TEPULN2003.LIB                                 89.7 KB   a part of the project -> LIBRARY folder
|-- Proteus Model Files/
|   |-- TEPNET.DLL                                     2.89 MB   a model -> MODELS folder
|   |-- TEPSPLITFLAP.DLL                              290.5 KB   a model -> MODELS folder
|   |-- TEPULN2003.DLL                                308.0 KB   a model -> MODELS folder
|   |-- TEPPi/python/                                 17.54 MB   Python 3.11 embeddable -> MODELS\TEPPi (33 files)
|   |-- TEPPi/runtime/                                 1.11 MB   TEP Pi runtime, gpiozero -> MODELS\TEPPi (87 files)
|-- Proteus Simulation/
|   |-- Pi-5-Split-Flap-Message-Board.pdsprj           32.6 KB   the project simulation
|   |-- splitflap_board.py                             10.6 KB   the program PI1 runs
|   |-- TEPNET.DLL                                     2.89 MB   copy of the model
|   |-- TEPSPLITFLAP.DLL                              290.5 KB   copy of the model
|   |-- TEPULN2003.DLL                                308.0 KB   copy of the model
|-- Python Code/
|   |-- splitflap_board.py                             10.6 KB   the program (the same file)
|-- README.txt                                         ~9.9 KB   this file
Total: 25.89 MB (unzipped). The C++ source code of the models is not included.

WHAT IS IT?
  A four-character split-flap message board you can run in Proteus - the clattering flaps of railway departure
  boards: a Raspberry Pi 5 drives four split-flap modules through four ULN2003 boards, finds each module's home
  with its hall sensor, shows words and the time, and serves a web dashboard.
    * Four split-flap modules (SPLITFLAPTEP, DS1 - DS4): a 28BYJ-48 5 V stepper turns a spool of 40 flaps (blank,
      A - Z, 0 - 9, . - ?), only forwards; RED (the common) on the 5 V rail; a hall sensor's HOME goes LOW once a turn,
      1.5 deg into the blank flap (the hall board's VCC on the Pi's 3.3 V pin 1, its own 10 k pull-up).
    * Four ULN2003 boards (ULN2003ADVTEP, DRV1 - DRV4): IN1 - IN4 from the Pi, + on the 5 V rail, - to GND; A - D to
      the module's ORANGE, YELLOW, PINK and BLUE; COM on the 5 V rail.
    * The Pi's pins (BCM): module 1 IN1 - IN4 GPIO4, 17, 27, 22, HOME GPIO26; module 2 GPIO5, 6, 13, 19, HOME GPIO7;
      module 3 GPIO18, 23, 24, 25, HOME GPIO8; module 4 GPIO12, 16, 20, 21, HOME GPIO11.
    * RASPBERRY PI 5 (PI1) runs splitflap_board.py on Ethernet at 192.168.1.51 (port 8000).
    * Laptop WiFi Monitor (PC1) and Mobile WiFi Monitor (MOB1) open http://192.168.1.51:8000/.
  The rules (at the top of the program):
    * half steps in the order A, AB, B, BC, C, CD, D, DA; 4075.77 half steps a turn (64 x 63.68, NOT 4096);
      40 flaps of 9 deg: flap k is shown from k x 9 deg, its middle at k x 9 + 4.5 deg;
    * all four modules step from one thread, each on its own clock, with a ramp from 5 to 12 r/min over 120 half steps
      (and back down); only forwards, so a letter further back goes all the way round;
    * every HOME pulse sets that module's position again (it never drifts); at the start each module turns to its
      magnet first (homing); a module that already shows the letter stays still;
    * 150 ms after a module stops, its coils are switched off: the gearbox holds the spool.
  Its pages:
    /            the dashboard: the controls, what the board shows, the word asked, the home passes, the events
    /open  /busy  /free     a word
    /clock       the time as HHMM, shown again every minute
    /home        find home again
    /data        everything as JSON
  No extra Python library: lgpio (in the TEPPi runtime and on Raspberry Pi OS), threading, time, http.server.

TEST STATUS
  Tested in Proteus 8 Professional on Windows 11, the run that made the tutorial's screenshots (the program's times):
  - 0 - 5.1 s: homing - every spool rests on its blank flap with the magnet at the sensor (HOME already LOW), so each
    turns a whole turn to the next HIGH-to-LOW edge: "module 1 - 4: home found" at 5.1 s (1.5 deg, 17 half steps).
  - 5.8 - 7.2 s: OPEN - 'E' at 5.8 s, 'N' 6.9 s, 'O' 7.0 s, 'P' 7.2 s: "the board shows OPEN - 7.2 s".
  - 17.5 s: BUSY from the phone - the flaps falling (a sheet shot at 18 s shows Z-U-P-Y on the way); 'U' 18.3 s,
    'Y' 19.1 s, 'S' 19.4 s, 'B' 21.1 s (27 flaps, all the way round from O): "BUSY - 3.5 s".
  - 27.5 s: FREE from the laptop - 'F' 28.2 s, 'E' 30.2 / 30.9 s, 'R' 32.3 s: "FREE - 4.8 s".
  - 36.3 s: CLOCK - "0953" (the PC's time) at 40.5 s, 3.5 s.
  - 44.4 s: HOME from the phone - all four turn to their magnets again (45.0 - 46.1 s), then "0953" again at 49.6 s.
  - The models: 0 lost steps on every module, 3 home passes each, the flap each shows = the flap the program counts;
    ramps from 5 to 12 r/min; 54.1 s of simulation in 320 s.

INSTALLATION
  1. Close Proteus. Extract the WHOLE zip file, for example to your Desktop.
  2. Copy the files from "Proteus Library Files" into the LIBRARY folder of Proteus, for example
     C:\Program Files (x86)\Labcenter Electronics\Proteus 8 Professional\LIBRARY
  3. Copy everything in "Proteus Model Files" - the DLL files and the TEPPi folder - into the MODELS folder (next
     to LIBRARY).
  4. Start Proteus. Press P in the schematic and search for RASPBERRY PI 5, SPLITFLAPTEP or ULN2003ADVTEP to check
     that the parts are there.

RUN THE SIMULATION
  1. Open "Proteus Simulation\Pi-5-Split-Flap-Message-Board.pdsprj". Keep splitflap_board.py and the DLL files
     beside it.
  2. Press Play. The Pi's terminal opens; every module turns to its home, then the board shows OPEN.
  3. Open the Laptop WiFi Monitor (PC1) or the Mobile WiFi Monitor (MOB1), press Go and try BUSY, FREE and CLOCK.
  Your own program: edit splitflap_board.py beside the project (PI1's PROGRAM property) and press Play again.

PROPERTIES USED IN THIS PROJECT
  PI1 RASPBERRY PI 5           PROGRAM=splitflap_board.py, ETHERNET=IN (192.168.1.51)
  DS1 - DS4 SPLITFLAPTEP       (no changes)
  DRV1 - DRV4 ULN2003ADVTEP    (no changes)
  PC1, MOB1                    HOMEPAGE=http://192.168.1.51:8000/

TROUBLESHOOTING
  * A module never finds home: its HOME not on the right GPIO, or the hall board without VCC.
  * A module shows the letter next to the one asked: the steps a turn wrong (4096 instead of 4075.77) - it drifts.
  * A module hums and stops (JAMMED or lost steps): too fast (above about 17 r/min) or turned backwards.
  * The coils get warm: they stay on - switch them off after a stop (the gearbox holds the spool).
  * The terminal cannot start Python: the TEPPi folder is not in MODELS.

LICENCES
  * The project, the program, the parts (LIB files) and the models (DLL files) are made by The Engineering Projects
    and are free for learning and for your own projects. The models use only standard Windows libraries.
    The C++ source code of the models is not included; the source code is not included for any model.
  * TEPPi\python is the Python 3.11 Windows embeddable package (Python Software Foundation License); TEPPi\runtime
    holds our TEP Pi runtime with gpiozero and colorzero (BSD licences) - their licence files are inside the folders.
  * Proteus is a product of Labcenter Electronics and is not included. Raspberry Pi is a trademark of Raspberry Pi
    Ltd; the 28BYJ-48 and the ULN2003 are made by several companies.
    This project is not made or endorsed by them.

VERSION
  V1.0 - the first release of the project.
===============================================================================================================
Advertisement

Development1 release

  1. V1.0IoT Split-Flap Message Board with Raspberry Pi 5 - Proteus Simulation V1.0this page

    V1.0 is the only release in the Download Center so far. When a newer version is published, it appears above with its own download page.

Installation7 steps

From the download to a working project, in order. The steps follow what the package contains.

You will need

  • Proteus Design SuiteProteus 8 or newer (Labcenter), on Windows
  • Pythonto build the source files into firmware
  • Any archive toolWindows, macOS and Linux extract ZIP files on their own

Steps

  1. 1

    Extract the archive

    Right-click 90ea3659beb1432ab63b0651544b7476.zip and choose Extract All (or open it with 7-Zip or WinRAR) into a folder you can find again. Keep its folder structure (Pi-5-Split-Flap-Message-Board-TEP-v1.0) as it is.

  2. 2

    Copy the library files into Proteus

    Move TEPLAPTOP.LIB, TEPMOBILE.LIB and TEPRPI5.LIB and 2 more and the files into the LIBRARY folder of your Proteus installation: C:\Program Files (x86)\Labcenter Electronics\Proteus 8 Professional\LIBRARY for Proteus 8, or the matching Proteus 7 folder. Older versions keep it under ProgramData\Labcenter Electronics. If Proteus is open, close it first.

  3. 3

    Add the simulation model

    Copy TEPNET.DLL, TEPSPLITFLAP.DLL and TEPULN2003.DLL and 7 more into the MODELS folder next to LIBRARY, so the component can run, not only be drawn.

  4. 4

    Restart Proteus and place the component

    Start Proteus, open a schematic, press P (Pick Devices) and search for the component by the name used in the tutorial. It appears with its pins ready to wire.

  5. 5

    Build the source code

    Open splitflap_board.py, attr.py and color.py and 28 more in the compiler named in the tutorial (MikroC, Keil, MPLAB, Code Composer or the Arduino IDE) and build it to get the firmware.

  6. 6

    Open the example simulation

    Open Pi-5-Split-Flap-Message-Board.pdsprj in Proteus to see the wiring exactly as in the tutorial. Check the controller's Program File path, then press Play.

  7. 7

    Follow the tutorial

    IoT Split-Flap Message Board with Raspberry Pi 5 - Proteus Simulation explains every connection and setting in order; keep it open beside the files while you build.

How to add a library in Proteus 8

FAQs8 questionsContact TEP

How do I download IoT Split-Flap Message Board with Raspberry Pi 5 - Proteus Simulation V1.0?

Wait for the 30-second guest countdown on this page, then press the download button; the file comes straight from our storage. Members who are logged in skip the wait. If the browser opens the file instead of saving it, use its Save as option. The download link is made for you when the countdown ends and works for 15 minutes; a saved or shared link stops working, so share this page instead.

What is inside the archive?

IoT Split-Flap Message Board with Raspberry Pi 5 - Proteus Simulation V1.0 comes as a ZIP archive of 135 files (13.3 MB, 25.9 MB unpacked) holding Proteus library files, simulation model DLLs, a Proteus simulation, source code and a nested archive. Open the File Structure tab for the full list of 135 files.

What should I do if the download does not start?

Check the browser's download list first; an ad blocker or a company firewall can also hold it back, so try another browser or network. If the file arrives incomplete, download it again. For an installation problem, read the Install tab or tell us in the comments with your software version and the exact error message.

Is this file free?

Yes. Every file in the TEP Download Center is free for learning, personal and student projects. If you share it, link back to this page or the tutorial so others find the latest version.

How do I check that the file arrived complete?

Compare its SHA-256 with the one on this page, 48b3d763a8795f0724842cfac929fbd0683c6430dfae4b1f87b38296f2376775. In PowerShell run Get-FileHash "90ea3659beb1432ab63b0651544b7476.zip"; on macOS or Linux run shasum -a 256 "90ea3659beb1432ab63b0651544b7476.zip". The same value means the file is exactly the one in our storage; a different one means the download broke off, so download it again.

Do I need WinRAR to open the ZIP file?

No. Windows, macOS and Linux open ZIP archives on their own (Extract All, or double-click). WinRAR and 7-Zip work too. Extract the whole archive before using the files.

Where do I put the LIB and IDX files?

Both files go into the LIBRARY folder of your Proteus installation (Proteus 8: C:\Program Files (x86)\Labcenter Electronics\Proteus 8 Professional\LIBRARY; Proteus 7 has the same folder under its own name). Restart Proteus afterwards and search for the component with P.

Which Proteus version does the library need?

The tutorial names the Proteus version the library was made and tested with. Most TEP libraries work in Proteus 7 and Proteus 8; if the component does not appear after a restart, check that both the LIB and the IDX file were copied and that Proteus was fully closed while copying.

preparing · 90ea3659beb1432ab63b0651544b7476.zip
Rating
Your download will be ready shortly
Preparing your download…

Members skip the wait. Log in or join TEP.

Last 14 days0 downloads
SHA-256 48b3d763a8795f0724842cfac929fbd0683c6430dfae4b1f87b38296f2376775
DocumentationIoT Split-Flap Message Board with Raspberry Pi 5 - Proteus Simulation
Need help with this file? Bug report Ask a question Download problemsGet updates
Advertisement

Comments

0

Join the conversation

Start the conversationAsk a question or share how you used this download.