Project Files of FRDM-MCXN947 Library for Proteus: NXP MCX N947 Tiny AI Simulation
64a6aac389404603875714f3ca13acd8.zip

FRDM-MCXN947 Library for Proteus V1.0
FRDM-MCXN947 Library for Proteus V1.0 comes as a ZIP archive of 305 files (3.6 MB, 8.0 MB unpacked) holding Proteus library files, simulation model DLLs, a Proteus simulation, an Arduino sketch, an Arduino library, compiled HEX firmware and source code.
- LIBProteus library
- DLLProteus model
- DSNProteus simulation
- INOArduino sketch
- LIBArduino library
- HEXHEX firmware
- SRCSource code
Description
FRDM-MCXN947-Library-for-Proteus-v1.0.zip with NXP's FRDM-MCXN947 in Proteus (your sketch with D0 .. D15, A0 .. A5, the RGB LED, SW2, SW3 and a serial monitor; TEPFRDMN947.LIB, TEPNET.DLL and the TEP Boards for Proteus add-on 1.74.0), the BME280 library, the tiny neural network demo with its sketch and a README.
File Structure
4.8 KB1.1 KB7.7 KB11 KB8.5 KB1.5 KB1.7 KB1.9 KB5.7 KB4.9 KB1.1 KB5.8 KB9.6 KB7.2 KB2.5 KB2.1 KB1.9 KB2.1 KB4.4 KB1.1 KB3 KB3 KB1.8 KB2.5 KB3.5 KB149 B2.7 KB2 KB6.4 KB3.2 KB1.3 KB963 B8.6 KB5.9 KB6 KB12 KB1.6 KB1.3 KB14.7 KB4.3 KB6.1 KB20.1 KB8.2 KB2 KB4.5 KB311 B12.8 KB6.7 KB6.1 KB2.2 KB3.4 KB5.9 KB1.5 KB1.6 KB16.6 KB9.7 KB6.9 KB2.1 KB533 B5.7 KB7.4 KB514 B1.7 KB896 B481 B1.4 KB1012 B482 B936 B559 B467 B3.6 KB3.8 KB504 B956 B575 B455 B8.3 KB10.9 KB522 B79 B5.5 KB3.1 KB79 B442 B918 B1.4 KB1.8 KB1 KB1.3 KB1.4 KB1.8 KB1.4 KB5.7 KB502 B463 B5 KB6.5 KB3.4 KB3.4 KB500 B1.6 KB368 B406 B466 B404 B444 B460 B477 B739 B448 B1.3 KB350 B5.7 KB4 KB562 B1.5 KB2 KB550 B7.2 KB4.1 KB371 B4.5 KB3.5 KB492 B390 B478 B6.6 KB2.4 KB479 B5.1 KB1.9 KB1.3 KB1.3 KB750 B1.3 KB490 B2.2 KB1.9 KB498 B1.2 KB1.2 KB487 B5.1 KB4.6 KB371 B3.6 KB2.5 KB534 B1.5 KB1.2 KB478 B6.2 KB3 KB1.5 KB1.7 KB469 B1 KB1.7 KB433 B294 B358 B1.3 KB2.5 KB13.2 KB3.8 KB659 B510 B4.4 KB1.9 KB5.8 KB11 KB835 B518 B308 B1.3 KB3.3 KB568 B6.4 KB2.3 KB29 B436 B9.2 KB4.9 KB439 B4.2 KB1.5 KB9.3 KB7.1 KB4.7 KB2.4 KB388 B5.1 KB893 B667 B1.3 KB5.5 KB2.3 KB1.8 KB468 B882 B530 B791 B487 B894 B2 KB730 B646 B2.6 KB977 B702 B20.6 KB1.8 KB11.8 KB3.2 KB596 B406 B6.3 KB5.7 KB9.3 KB7.7 KB7.7 KB6.1 KB5.8 KB5.9 KB6.4 KB6.4 KB5.3 KB5.6 KB5.7 KB7.9 KB7.7 KB6.5 KB6.3 KB6.2 KB5.9 KB10.3 KB8.5 KB6.6 KB7.6 KB6.7 KB6.1 KB6.7 KB8.3 KB6.2 KB7.2 KB5.9 KB5.6 KB5.7 KB6.7 KB5.9 KB6.2 KB6 KB6 KB6.1 KB6.3 KB6 KB6.1 KB6.2 KB6 KB5.8 KB6.4 KB6.4 KB6.9 KB6 KB6.8 KB7 KB6.3 KB6.4 KB6.5 KB6.5 KB6.6 KB6.5 KB5.6 KB6.6 KB5.9 KB7.5 KB3.8 KB5.4 KB7.7 KB7.1 KB5.8 KB5.9 KB5.9 KB6.9 KB5.7 KB5.9 KB5.5 KB5.5 KB7.1 KB5.2 KB36.3 KB25.9 KB1.3 KB8.5 KB36.1 KB89.4 KB34.4 KB381 KB2.9 MB19.4 KB48.4 KB381 KB2.9 MB10 KBGallery12 images from the tutorialOpen the tutorial
The circuit, the board and the results as they appear in FRDM-MCXN947 Library for Proteus: NXP MCX N947 Tiny AI Simulation. Open an image for its full size.












README
FRDM-MCXN947 LIBRARY FOR PROTEUS - V1.0 (YOUR ARDUINO SKETCH, THE RGB LED, SW2 AND SW3)
Designed by The Engineering Projects
www.TheEngineeringProjects.com
IMPORTANT LINKS
Article (read it first - pictures, step by step, every feature explained):
https://www.theengineeringprojects.com/2026/11/frdm-mcxn947-library-for-proteus.html
Report a bug or suggest a feature (our forum):
https://www.theengineeringprojects.com/forum
Support us (the libraries are free):
https://www.theengineeringprojects.com/donate
FILE STRUCTURE
FRDM-MCXN947-TEP-v1.0/
|-- Proteus Library Files/
| |-- TEPBME280.LIB 89.4 KB the BME280 (demo), to LIBRARY
| |-- TEPFRDMN947.LIB 34.4 KB the FRDM-MCXN947, to LIBRARY
|-- Proteus Model Files/
| |-- TEPBME280.DLL 381.0 KB the BME280, to MODELS
| |-- TEPNET.DLL 2.93 MB the board + monitors + network, to MODELS
|-- Arduino Code/
| |-- FRDM_Comfort_AI/FRDM_Comfort_AI.ino 4.8 KB the demo sketch
| |-- TEP Boards for Proteus/hardware/ 1.22 MB the Arduino IDE add-on 1.74.0 (295 files)
|-- Proteus Simulation/
| |-- FRDM_Comfort_AI.hex 48.4 KB the demo sketch (U1)
| |-- FRDM-Tiny-AI-Comfort.pdsprj 19.4 KB the demo: a tiny neural network for room comfort
| |-- TEPBME280.DLL 381.0 KB copy of the model
| |-- TEPNET.DLL 2.93 MB copy of the model
|-- README.txt ~10.1 KB this file
Total: 8.03 MB (unzipped). The source code of the models is not included.
WHAT IS IT?
Proteus 8 has no MCX N947 model, so this is NOT a real MCX N947. Our team has put a lot of effort into building this
board ourselves: it is NXP's FRDM-MCXN947 - the black development board with the MCX N947 (two Arm Cortex-M33 at 150
MHz, the eIQ Neutron NPU for machine learning, 2 MB of flash, 512 KB of RAM), the MCU-Link debugger with its USB-C, the
high-speed USB-C and the RJ45 Ethernet jack, the RGB LED, the buttons SW2 and SW3 and RESET, the Arduino R3 headers and
the mikroBUS socket - drawn compact, and it runs YOUR Arduino sketch in Proteus:
* NXP makes no Arduino core for this board, so the pins have TEP names in the Arduino R3 style: D0 .. D15, A0 .. A5,
LED_RED / LED_GREEN / LED_BLUE, SW2, SW3. You compile with our board package "TEP Boards for Proteus" 1.74.0 (in
Arduino Code - see INSTALLATION).
* The RGB LED: each colour lights when its pin is LOW (LED_BUILTIN is LED_RED). SW2 and SW3 read LOW while you hold
them: click them on the board in the running simulation.
TEP additions: the MCU-Link's USB opens the serial monitor (the same window as our TEP Serial Monitor Advance).
Limits (say them before you start): your sketch is one program (the second core and the NPU are not modelled: the
demo's neural network runs in the sketch). The Ethernet jack, the high-speed USB, the mikroBUS socket, the camera and
LCD headers are drawn, not modelled. Your sketch gets 8 KB of RAM in the simulation (the real one: 512 KB), about 256 KB
of flash, and int is 16 bits in the simulation (use long for big numbers). See MODEL SCOPE AND LIMITS.
ONE DEVICE (search "FRDM" in Pick Devices):
FRDM-MCXN947 "FRDM-MCXN947" V1.0 (Microprocessor ICs > NXP Boards), prefix U, model TEPNET.DLL.
Its TEP window has no Windows title bar: the serial monitor (the MCU-Link's USB, 115200 baud: Monitor, Plotter and
Board tabs).
The same TEPNET.DLL also runs our other sketch boards; it replaces any older TEPNET.DLL (keep only this newest one in
MODELS).
TEST STATUS
V1.0: verified in Proteus 8.5 on 17 Nov 2026 with the demo project as shipped. What the Proteus run showed:
* FRDM-Tiny-AI-Comfort: "Network: 2 inputs, 6 hidden (ReLU), 3 outputs", ">> The network says: COMFORT (100 %) 24.0 C
45 %", the RGB LED green.
* The BME280's window at 32.5 C: "HOT/HUMID", the LED red; SW2: "Scores: COLD 0 % COMFORT 0 % HOT/HUMID 100 %"; at
10 C: "COLD", the LED blue; at 25 C: "COMFORT", green; 25 C with 86 %: "HOT/HUMID", red; 46 %: "COMFORT", green.
* SW3: "Self-test:" 24 C 45 % COMFORT, 30 C 45 % HOT/HUMID, 10 C 45 % COLD, 25 C 85 % HOT/HUMID, 16 C 60 % COLD,
21 C 55 % COMFORT.
* about 21 s of simulation, no errors, with the BME280 window and the monitor open.
INSTALLATION (about 3 minutes)
1. Close Proteus. Extract the WHOLE ZIP to a normal folder (e.g. Desktop).
2. Copy everything in "Proteus Library Files" to the LIBRARY folder of Proteus, for example:
C:\Program Files (x86)\Labcenter Electronics\Proteus 8 Professional\LIBRARY
(on some PCs: C:\ProgramData\Labcenter Electronics\Proteus 8 Professional\LIBRARY). TEPFRDMN947.LIB is the board;
TEPBME280.LIB is the demo's sensor.
3. Copy the DLLs from "Proteus Model Files" to the MODELS folder (...\Proteus 8 Professional\MODELS) - replace an older
TEPNET.DLL (this one is the first that knows this board).
4. Delete TEPFRDMN947.IDX from the LIBRARY folder if it is there.
5. The Arduino IDE (only to compile your own sketches - the demo has its HEX file): copy the folder
"Arduino Code\TEP Boards for Proteus\hardware" into your sketchbook folder (normally Documents\Arduino), so that
Documents\Arduino\hardware\tep\avr\boards.txt exists (replace an older copy); restart the IDE. The Arduino AVR Boards
platform must be installed (it comes with IDE 1.8.x; in IDE 2.x install "Arduino AVR Boards" from the Boards
Manager once).
Tools > Board > TEP Boards for Proteus > NXP FRDM-MCXN947 (TEP Proteus). The demo also needs Adafruit BME280 and
Adafruit Unified Sensor (Library Manager).
6. Start Proteus. In Pick Devices (P) search "FRDM".
RUN THE DEMO
Keep the .hex file and the DLLs beside the project in "Proteus Simulation".
FRDM-Tiny-AI-Comfort.pdsprj - U1 the FRDM-MCXN947 (FRDM_Comfort_AI.hex) runs a tiny neural network (2 inputs, 6 hidden
neurons, 3 outputs, trained offline) on the room's air: U2 = BME280 on SDA / SCL (D14 / D15).
Press Run. The monitor prints "The network says: COMFORT" and the RGB LED is green. In the BME280's window click the
temperature track: at 32.5 C the network says HOT/HUMID (red), at 10 C COLD (blue); at 25 C with 85 % humidity HOT/HUMID
again. SW2 prints the three scores as percentages; SW3 runs a self-test on six known rooms.
Closed a window? The MCU-Link's USB opens the monitor.
THE PINS (the label on the board, the core's number, what it can do in the simulation)
D0 .. D13 0 .. 13 GPIO, PWM (analogWrite), interrupt; D0 / D1 Serial1 RX / TX; D10 .. D13 SPI (SS, MOSI,
MISO, SCK)
SDA, SCL 14, 15 D14 / D15: Wire, the I2C bus
A0 .. A5 16 .. 21 analogRead 0 .. 1023 for 0 .. 3.3 V, or GPIO
3V3, 5V, GND, RESET 3.3 V (the logic), 5 V, ground, the board's reset; AREF, VIN drawn, not modelled
LED_RED / LED_GREEN / LED_BLUE (22 / 23 / 24) are the RGB LED, each lit when LOW; LED_BUILTIN is LED_RED. SW2 / SW3
(25 / 26) are the buttons, LOW when pressed (pinMode INPUT_PULLUP). Serial is the MCU-Link's virtual COM port: the
board's built-in monitor.
PROPERTIES (double-click the part > Edit Properties)
PROGRAM the sketch's HEX (Arduino IDE: Sketch > Export Compiled Binary, board NXP FRDM-MCXN947 (TEP Proteus))
MONITOR YES = the built-in serial monitor on Serial; BAUD its speed (115200, or AUTO)
AUTOOPEN YES = the monitor window opens at Run (the demo: YES)
TROUBLESHOOTING
* The LED looks inverted: each colour of the RGB LED lights when its pin is LOW.
* A colour mixes: switch the other two colours off (HIGH) when you light one.
* A button seems dead: use pinMode(SW2, INPUT_PULLUP) and act on the change to LOW.
* "BME280 not found": check SDA / SCL and the address (0x76 when SDO is on GND).
* An integer goes wrong above 32767: int is 16 bits in the simulation - use long.
BUG REPORTS AND FEATURE REQUESTS
Please post them in our forum with a screenshot and the Serial Monitor text:
https://www.theengineeringprojects.com/forum
LICENCES AND THIRD-PARTY NOTES
* The board model (TEPNET.DLL) and the symbols and artwork (TEPFRDMN947.LIB) are made by The Engineering Projects. The
source code of the models is not included.
* TEP Boards for Proteus (Arduino Code): its core, the variants and the EEPROM, SPI and Wire libraries are modified
copies of the Arduino AVR core 1.8.6 - GNU Lesser General Public License 2.1 (LGPL 2.1, the text:
LICENSE-LGPL-2.1.txt); the others and our core files are MIT (LICENSE-MIT.txt).
* Proteus is a product of Labcenter Electronics and is not included. NXP, FRDM, MCX and eIQ are names of NXP
Semiconductors, Arduino of Arduino. This library is not made or endorsed by them or by Labcenter.
REBUILDING THE FIRMWARE (OPTIONAL)
The HEX file is supplied. Install TEP Boards for Proteus (INSTALLATION step 5), open Arduino Code\FRDM_Comfort_AI,
select NXP FRDM-MCXN947 (TEP Proteus) and use Sketch > Export Compiled Binary. tools\train_comfort_net.py (in the
library's sources, not shipped) trained the network's weights. For a real board use MCUXpresso or Zephyr (board
frdm_mcxn947): the same network runs in C, and NXP's eIQ tools can move larger models onto the NPU. Its pins work at
3.3 V.
MODEL SCOPE AND LIMITS
Modelled: D0 .. D15 and A0 .. A5; digital I/O, analogRead 0 .. 1023, PWM (analogWrite), tone and attachInterrupt
through the board model; Serial (the board's monitor), Serial1, Wire and SPI; the RGB LED, SW2, SW3 and RESET.
Not modelled: the MCX N947 itself, its second core and the NPU, Ethernet, the USB ports, the mikroBUS socket, the camera
and LCD headers. The simulation runs below real time.
VERSION
TEP FRDM-MCXN947 library V1.0 (Nov 2026). Device FRDM-MCXN947 (TEPFRDMN947.LIB / TEPNET.DLL), TEP Boards for Proteus
1.74.0 (adds this board: D0 .. D15, A0 .. A5, LED_RED / LED_GREEN / LED_BLUE, SW2, SW3).
Demo sketch FRDM_Comfort_AI V1.0. Demo part: BME280 (Advance).Development1 release
-
V1.0FRDM-MCXN947 Library for Proteus V1.0this page
V1.0 is the only release in the Download Center so far. When a newer version is published, it appears above with its own download page.
Installation10 steps
From the download to a working project, in order. The steps follow what the package contains.
You will need
- Proteus Design SuiteProteus 8 or newer (Labcenter), on Windows
- Arduino IDE1.8 or 2.x, with the board of the tutorial chosen under Tools → Board
- The compiler named in the tutorialto build the source files into firmware
- Any archive toolWindows, macOS and Linux extract ZIP files on their own
Steps
- 1
Extract the archive
Right-click 64a6aac389404603875714f3ca13acd8.zip and choose Extract All (or open it with 7-Zip or WinRAR) into a folder you can find again. Keep its folder structure (FRDM-MCXN947-TEP-v1.0) as it is.
- 2
Copy the library files into Proteus
Move TEPBME280.LIB and TEPFRDMN947.LIB and the files into the LIBRARY folder of your Proteus installation: C:\Program Files (x86)\Labcenter Electronics\Proteus 8 Professional\LIBRARY for Proteus 8, or the matching Proteus 7 folder. Older versions keep it under ProgramData\Labcenter Electronics. If Proteus is open, close it first.
- 3
Add the simulation model
Copy TEPBME280.DLL and TEPNET.DLL into the MODELS folder next to LIBRARY, so the component can run, not only be drawn.
- 4
Restart Proteus and place the component
Start Proteus, open a schematic, press P (Pick Devices) and search for the component by the name used in the tutorial. It appears with its pins ready to wire.
- 5
Install the Arduino library
In the Arduino IDE choose Sketch → Include Library → Add .ZIP Library and pick the library, or copy its folder into Documents\Arduino\libraries. Restart the IDE to see its examples.
- 6
Open the sketch in the Arduino IDE
Open FRDM_Comfort_AI.ino, eeprom_clear.ino and eeprom_crc.ino and 17 more, select your board and port under Tools, then Verify. Sketch → Export Compiled Binary writes the HEX file a simulation needs.
- 7
Build the source code
Open abi.cpp, Arduino.h and binary.h and 52 more in the compiler named in the tutorial (MikroC, Keil, MPLAB, Code Composer or the Arduino IDE) and build it to get the firmware.
- 8
Load the HEX file
In Proteus double-click the microcontroller, set Program File to FRDM_Comfort_AI.hex and run the simulation. For real hardware, flash the same file with your programmer.
- 9
Open the example simulation
Open FRDM-Tiny-AI-Comfort.pdsprj in Proteus to see the wiring exactly as in the tutorial. Check the controller's Program File path, then press Play.
- 10
Follow the tutorial
FRDM-MCXN947 Library for Proteus: NXP MCX N947 Tiny AI Simulation explains every connection and setting in order; keep it open beside the files while you build.
FAQs9 questionsContact TEP
How do I download FRDM-MCXN947 Library for Proteus V1.0?
Wait for the 30-second guest countdown on this page, then press the download button; the file comes straight from our storage. Members who are logged in skip the wait. If the browser opens the file instead of saving it, use its Save as option. The download link is made for you when the countdown ends and works for 15 minutes; a saved or shared link stops working, so share this page instead.
What is inside the archive?
FRDM-MCXN947 Library for Proteus V1.0 comes as a ZIP archive of 305 files (3.6 MB, 8.0 MB unpacked) holding Proteus library files, simulation model DLLs, a Proteus simulation, an Arduino sketch, an Arduino library, compiled HEX firmware and source code. Open the File Structure tab for the full list of 305 files.
What should I do if the download does not start?
Check the browser's download list first; an ad blocker or a company firewall can also hold it back, so try another browser or network. If the file arrives incomplete, download it again. For an installation problem, read the Install tab or tell us in the comments with your software version and the exact error message.
Is this file free?
Yes. Every file in the TEP Download Center is free for learning, personal and student projects. If you share it, link back to this page or the tutorial so others find the latest version.
How do I check that the file arrived complete?
Compare its SHA-256 with the one on this page, e8a82f214f195d042fc62e08204184480bd496ed086a51f83a9c7049603309a0. In PowerShell run Get-FileHash "64a6aac389404603875714f3ca13acd8.zip"; on macOS or Linux run shasum -a 256 "64a6aac389404603875714f3ca13acd8.zip". The same value means the file is exactly the one in our storage; a different one means the download broke off, so download it again.
Do I need WinRAR to open the ZIP file?
No. Windows, macOS and Linux open ZIP archives on their own (Extract All, or double-click). WinRAR and 7-Zip work too. Extract the whole archive before using the files.
Where do I put the LIB and IDX files?
Both files go into the LIBRARY folder of your Proteus installation (Proteus 8: C:\Program Files (x86)\Labcenter Electronics\Proteus 8 Professional\LIBRARY; Proteus 7 has the same folder under its own name). Restart Proteus afterwards and search for the component with P.
Which Proteus version does the library need?
The tutorial names the Proteus version the library was made and tested with. Most TEP libraries work in Proteus 7 and Proteus 8; if the component does not appear after a restart, check that both the LIB and the IDX file were copied and that Proteus was fully closed while copying.
How do I get the HEX file into the simulation?
Compile the sketch in the Arduino IDE (Sketch → Export Compiled Binary gives you the HEX next to the sketch), then in Proteus double-click the board, set Program File to that HEX and run.
Members skip the wait. Log in or join TEP.
- 0Total downloads
- 4%Popularity
- ProteusCategory
- 0Comments
- ssyedzainnasirUploaded by
- 20 Nov 2026Uploaded at
e8a82f214f195d042fc62e08204184480bd496ed086a51f83a9c7049603309a0
















Comments
0