Project Files of xG24 Explorer Kit Library for Proteus: BLE Smart Fan Simulation
8a4d23be1670455794606474ec90d28b.zip

xG24 Explorer Kit Library for Proteus V1.0
xG24 Explorer Kit Library for Proteus V1.0 comes as a ZIP archive of 298 files (4.4 MB, 10.3 MB unpacked) holding Proteus library files, simulation model DLLs, a Proteus simulation, an Arduino sketch, an Arduino library, compiled HEX firmware and source code.
- LIBProteus library
- DLLProteus model
- DSNProteus simulation
- INOArduino sketch
- LIBArduino library
- HEXHEX firmware
- SRCSource code
Description
xG24-Explorer-Kit-Library-for-Proteus-v1.0.zip with the Silicon Labs xG24 Explorer Kit in Proteus (your sketch with D0 .. D6, A0 .. A7, LED0 / LED1, BTN0 / BTN1, the mikroBUS signals on the pads, Bluetooth LE to a phone and a serial monitor; TEPXG24EK.LIB, TEPNET.DLL and the TEP Boards for Proteus add-on 1.66.0), the BME280, PIR, relay and phone libraries, the smart ventilation demo with its sketch and a README.
File Structure
1.1 KB7.7 KB11 KB8.5 KB1.5 KB1.7 KB1.9 KB5.7 KB4.9 KB1.1 KB5.8 KB9.6 KB7.2 KB2.5 KB2.1 KB1.9 KB2.1 KB4.4 KB1.1 KB3 KB3 KB1.8 KB2.5 KB3.5 KB149 B2.7 KB2 KB6.4 KB3.2 KB1.3 KB963 B8.6 KB5.9 KB6 KB12 KB1.6 KB1.3 KB14.7 KB4.3 KB6.1 KB20.1 KB8.2 KB2 KB4.5 KB311 B12.8 KB6.7 KB6.1 KB2.2 KB3.4 KB5.9 KB1.5 KB1.6 KB16.6 KB9.7 KB6.9 KB2.1 KB533 B5.7 KB7.4 KB514 B1.7 KB896 B481 B1.4 KB1012 B482 B936 B559 B467 B3.6 KB3.8 KB504 B956 B575 B455 B8.3 KB10.9 KB522 B79 B5.5 KB3.1 KB79 B442 B918 B1.4 KB1.8 KB1 KB1.3 KB1.4 KB1.8 KB1.4 KB5.7 KB502 B463 B5 KB6.5 KB3.4 KB3.4 KB500 B1.6 KB368 B406 B466 B404 B444 B460 B477 B739 B448 B1.3 KB350 B5.7 KB4 KB562 B1.5 KB2 KB550 B7.2 KB4.1 KB371 B4.5 KB3.5 KB492 B390 B478 B6.6 KB2.4 KB479 B5.1 KB1.9 KB1.3 KB1.3 KB750 B1.3 KB490 B2.2 KB1.9 KB498 B1.2 KB1.2 KB487 B5.1 KB4.6 KB371 B1.5 KB1.2 KB478 B6.2 KB3 KB1.5 KB1.7 KB469 B1 KB1.7 KB433 B294 B358 B1.3 KB2.5 KB13.2 KB3.8 KB659 B510 B4.4 KB1.9 KB5.8 KB11 KB835 B518 B6.4 KB2.3 KB29 B436 B9.2 KB4.9 KB439 B4.2 KB1.5 KB9.3 KB7.1 KB4.7 KB2.4 KB388 B5.1 KB893 B667 B1.3 KB5.5 KB2.3 KB1.8 KB468 B882 B530 B791 B487 B894 B2 KB730 B646 B2.6 KB977 B702 B20.6 KB1.8 KB11.8 KB3.2 KB596 B406 B6.3 KB5.7 KB9.3 KB7.7 KB7.7 KB5.8 KB5.9 KB6.4 KB6.4 KB5.3 KB5.6 KB5.7 KB7.9 KB7.7 KB6.5 KB6.3 KB6.2 KB10.3 KB8.5 KB6.6 KB7.6 KB6.7 KB6.1 KB6.7 KB8.3 KB6.2 KB7.2 KB5.9 KB5.6 KB5.7 KB6.7 KB5.9 KB6.2 KB6 KB6 KB6.1 KB6.3 KB6 KB6.1 KB6.2 KB6 KB5.8 KB6.4 KB6.4 KB6.9 KB6 KB6.8 KB7 KB6.5 KB6.6 KB6.5 KB5.6 KB7.5 KB3.8 KB7.7 KB7.1 KB5.8 KB5.9 KB5.9 KB6.9 KB5.7 KB5.9 KB5.5 KB5.5 KB7.1 KB5.2 KB32.3 KB25.9 KB1.3 KB8.5 KB35.2 KB6.6 KB89.4 KB391.6 KB39.5 KB13.1 KB490.4 KB29.7 KB381 KB400 KB2.9 MB330 KB381 KB400 KB2.9 MB330 KB30.5 KB60.3 KB12.8 KBGallery12 images from the tutorialOpen the tutorial
The circuit, the board and the results as they appear in xG24 Explorer Kit Library for Proteus: BLE Smart Fan Simulation. Open an image for its full size.












README
XG24 EXPLORER KIT LIBRARY FOR PROTEUS - V1.0 (YOUR ARDUINO SKETCH, BLUETOOTH LE, TWO LEDS, TWO BUTTONS, MIKROBUS PINS)
Designed by The Engineering Projects
www.TheEngineeringProjects.com
IMPORTANT LINKS
Article (read it first - pictures, step by step, every feature explained):
https://www.theengineeringprojects.com/2026/11/xg24-explorer-kit-library-for-proteus.html
Report a bug or suggest a feature (our forum):
https://www.theengineeringprojects.com/forum
The demo's other parts are our libraries (included) - their articles:
https://www.theengineeringprojects.com/2026/09/bme280-sensor-library-for-proteus.html
https://www.theengineeringprojects.com/2026/10/relay-module-library-for-proteus-v1-0.html
https://www.theengineeringprojects.com/2026/10/mobile-wifi-monitor-library-for-proteus.html
Support us (the libraries are free):
https://www.theengineeringprojects.com/donate
FILE STRUCTURE
xG24-Explorer-Kit-TEP-v1.0/
|-- Proteus Library Files/
| |-- TEPBME280.LIB 89.4 KB the BME280 (demo), to LIBRARY
| |-- TEPHCSR501.LIB 391.6 KB the PIR sensor (demo), to LIBRARY
| |-- TEPLAPTOP.LIB 39.5 KB the laptop (demo), to LIBRARY
| |-- TEPMOBILE.LIB 13.1 KB the phone (demo), to LIBRARY
| |-- TEPRELAY.LIB 490.4 KB the relay (demo), to LIBRARY
| |-- TEPXG24EK.LIB 29.7 KB the xG24 Explorer Kit, to LIBRARY
|-- Proteus Model Files/
| |-- TEPBME280.DLL 381.0 KB the BME280, to MODELS
| |-- TEPHCSR501.DLL 400.0 KB the PIR sensor, to MODELS
| |-- TEPNET.DLL 2.91 MB the board + monitors + network, to MODELS
| |-- TEPRELAY.DLL 330.0 KB the relay, to MODELS
|-- Arduino Code/
| |-- xG24_Smart_Ventilation/xG24_Smart_Ventilation.ino 6.6 KB the demo sketch
| |-- TEP Boards for Proteus/hardware/ 1.15 MB the Arduino IDE add-on 1.66.0 (280 files)
|-- Proteus Simulation/
| |-- TEPBME280.DLL 381.0 KB copy of the model
| |-- TEPHCSR501.DLL 400.0 KB copy of the model
| |-- TEPNET.DLL 2.91 MB copy of the model
| |-- TEPRELAY.DLL 330.0 KB copy of the model
| |-- xG24_Smart_Ventilation.hex 60.3 KB the demo sketch (U1)
| |-- xG24-BLE-Smart-Ventilation.pdsprj 30.5 KB the demo: a Bluetooth LE smart ventilation fan
|-- README.txt ~12.0 KB this file
Total: 10.29 MB (unzipped). The source code of the models is not included.
WHAT IS IT?
Proteus 8 has no EFR32MG24 model, so this is NOT a real EFR32MG24. Our team has put a lot of effort into building this
board ourselves: it is Silicon Labs' EFR32xG24 Explorer Kit (xG24-EK2703A, board BRD2703A) - the small black board with
the EFR32MG24 wireless SoC (an Arm Cortex-M33 with 1536 kB of flash, 256 kB of RAM and an AI/ML accelerator; Bluetooth
LE, Thread, Zigbee and Matter), the on-board J-Link debugger with its USB-C port, a mikroBUS socket for MikroElektronika
click boards, a Qwiic connector, two LEDs, two push buttons and the printed 2.4 GHz antenna - drawn compact, and it runs
YOUR Arduino sketch in Proteus:
* You write a normal sketch with the pin names of the Silicon Labs Arduino core (D0 .. D6, A0 .. A7, LED0 / LED1,
BTN0 / BTN1) and compile it in the Arduino IDE with our board package "TEP Boards for Proteus" 1.66.0 (in Arduino
Code - see INSTALLATION).
* The mikroBUS socket and the Qwiic connector are drawn on the part; their signals are on the pads: Wire (I2C) on
A2 (SDA) and A3 (SCL), SPI on D1 .. D4, Serial1 on A4 (TX) and A5 (RX). Wire any I2C, SPI or UART part to them.
* Bluetooth LE works through ArduinoBLE (the board as a peripheral, the phone of our Mobile WiFi Monitor as the
central: it scans, connects, reads, writes and gets notifications).
* LED0 / LED1 light when HIGH, as on the real kit (LED_BUILTIN is LED0). BTN0 / BTN1 read LOW while you hold them:
click a button on the board in the running simulation.
TEP additions: the USB-C port opens the serial monitor (the same window as our TEP Serial Monitor Advance).
Limits (say them before you start): Bluetooth LE: the board is a peripheral only; Thread, Zigbee and Matter are not
modelled. The Qwiic port's second I2C bus (Wire1) is not modelled: wire Qwiic parts to A2 / A3. The kit has no on-board
sensors. Your sketch gets 8 KB of RAM in the simulation (the real one: 256 KB), about 256 KB of flash, and int is 16
bits in the simulation (use long for big numbers). See MODEL SCOPE AND LIMITS.
ONE DEVICE (search "XG24" in Pick Devices):
XG24 EXPLORER KIT "xG24 Explorer Kit" V1.0 (Microprocessor ICs > Bluetooth Boards), prefix U, model TEPNET.DLL.
Its TEP window has no Windows title bar: the serial monitor (the USB-C port, 115200 baud: Monitor, Plotter and Board
tabs).
The same TEPNET.DLL also runs our other sketch boards and the phone; it replaces any older TEPNET.DLL (keep only this
newest one in MODELS).
TEST STATUS
V1.0: verified in Proteus 8.5 on 17 Nov 2026 with the demo project as shipped. What the Proteus run showed:
* xG24-BLE-Smart-Ventilation: "Advertising as "xG24 Vent"", a "Room:" line every 5 s (24.0 C, 50 %, 1013.0 hPa, empty,
fan OFF, auto).
* The phone's Bluetooth app: SCAN found "xG24 Vent", Connect: ">> Phone connected", the five values with their names.
* The HC-SR501's pop-up, Walk in: "Motion: room OCCUPIED", LED0 on; the BME280's pop-up, a warm room (32.5 C): "Fan ON
(warm and occupied)", LED1 and the relay on, the phone showed it.
* Walk out: "No motion for 8 s: room EMPTY", "Fan OFF (room empty)"; BTN0: "boost for 20 s", "Fan ON (boost)"; BTN1:
"mode OFF", "Fan OFF (mode OFF)".
* about 44 s of simulation, no errors, with the BME280's, the HC-SR501's and the relay's windows, the phone and the
monitor open.
INSTALLATION (about 3 minutes)
1. Close Proteus. Extract the WHOLE ZIP to a normal folder (e.g. Desktop).
2. Copy everything in "Proteus Library Files" to the LIBRARY folder of Proteus, for example:
C:\Program Files (x86)\Labcenter Electronics\Proteus 8 Professional\LIBRARY
(on some PCs: C:\ProgramData\Labcenter Electronics\Proteus 8 Professional\LIBRARY). TEPXG24EK.LIB is the board;
the others are the demo's parts: TEPBME280.LIB, TEPHCSR501.LIB, TEPRELAY.LIB, TEPMOBILE.LIB and TEPLAPTOP.LIB.
3. Copy the DLLs from "Proteus Model Files" (TEPNET.DLL, TEPBME280.DLL, TEPHCSR501.DLL, TEPRELAY.DLL) to the MODELS
folder (...\Proteus 8 Professional\MODELS) - replace an older TEPNET.DLL (this one is the first that knows this
board).
4. Delete TEPXG24EK.IDX from the LIBRARY folder if it is there.
5. The Arduino IDE (only to compile your own sketches - the demo has its HEX file): copy the folder
"Arduino Code\TEP Boards for Proteus\hardware" into your sketchbook folder (normally Documents\Arduino), so that
Documents\Arduino\hardware\tep\avr\boards.txt exists (replace an older copy); restart the IDE. The Arduino AVR Boards
platform must be installed (it comes with IDE 1.8.x; in IDE 2.x install "Arduino AVR Boards" from the Boards
Manager once).
Tools > Board > TEP Boards for Proteus > Silicon Labs xG24 Explorer Kit (TEP Proteus). ArduinoBLE is in the board
package. From the Library Manager: Adafruit BME280 Library and Adafruit Unified Sensor.
6. Start Proteus. In Pick Devices (P) search "XG24".
RUN THE DEMO
Keep the .hex file and the DLLs beside the project in "Proteus Simulation".
xG24-BLE-Smart-Ventilation.pdsprj - U1 the xG24 Explorer Kit (xG24_Smart_Ventilation.hex) is a meeting-room fan: U2 =
the BME280 (Advance) on the mikroBUS I2C pins A2 / A3 (SDO to GND: 0x76), U3 = the HC-SR501 motion sensor (Advance) on
D5, RLY1 = the fan's relay (Advance) on D0, MOB1 = the phone (Mobile WiFi Monitor), whose Bluetooth app connects.
Press Run. The monitor prints "Advertising as "xG24 Vent"" and a "Room:" line every 5 s; the room starts at 24 C and
50 %. In the phone's Bluetooth app press SCAN and connect to "xG24 Vent". On the HC-SR501's pop-up make a movement:
"Motion: room OCCUPIED", LED0 on. On the BME280's pop-up make the room warm: "Fan ON (warm and occupied)", LED1 and the
relay on. Walk out on the HC-SR501's pop-up: 8 s after its OUT drops, "room EMPTY", "Fan OFF (room empty)". BTN0 runs
the fan 20 s (boost); BTN1 switches the mode AUTO / OFF.
Closed a window? The USB-C port opens the monitor, the OPEN PANEL pads the BME280, the HC-SR501 and the relay, a click
on the phone's screen the phone.
THE PINS (the label on the board, the core's number, what it can do in the simulation)
D0 .. D6 0 .. 6 GPIO, PWM (analogWrite), interrupt; D1 MOSI, D2 MISO, D3 SCK, D4 SS (SPI)
A0, A1, A6, A7 7, 8, 13, 14 analogRead 0 .. 1023 for 0 .. 3.3 V, or GPIO
A2, A3 9, 10 SDA, SCL (Wire, the mikroBUS I2C), or GPIO
A4, A5 11, 12 Serial1 TX, RX (the mikroBUS UART), or GPIO
3V3, 5V, GND 3.3 V (the logic), 5 V, ground
LED0 / LED1 (15 / 16) are the LEDs, lit when HIGH; LED_BUILTIN is LED0, with LED_BUILTIN_ACTIVE (HIGH) and
LED_BUILTIN_INACTIVE. BTN0 / BTN1 (17 / 18) are the buttons, LOW when pressed (pinMode INPUT_PULLUP); BTN_BUILTIN is
BTN0 and BTN_BUILTIN_1 is BTN1. Serial is the USB-C port (the J-Link's virtual COM port): the board's built-in monitor.
PROPERTIES (double-click the part > Edit Properties)
PROGRAM the sketch's HEX (Arduino IDE: Sketch > Export Compiled Binary, board Silicon Labs xG24 Explorer Kit
(TEP Proteus))
MONITOR YES = the built-in serial monitor on Serial; BAUD its speed (115200, or AUTO)
AUTOOPEN YES = the monitor window opens at Run (the demo: YES)
TROUBLESHOOTING
* The phone finds nothing: press SCAN after "Advertising as" is printed; the sketch must call BLE.advertise().
* "BME280 not found": the demo's sensor is at 0x76 (SDO to GND) on A2 (SDA) / A3 (SCL).
* The fan acts backwards: the relay module switches on when IN is LOW (the sketch writes HIGH before OUTPUT).
* The LEDs look inverted: on this kit they light when the pin is HIGH.
* An integer goes wrong above 32767: int is 16 bits in the simulation - use long.
BUG REPORTS AND FEATURE REQUESTS
Please post them in our forum with a screenshot and the Serial Monitor text:
https://www.theengineeringprojects.com/forum
LICENCES AND THIRD-PARTY NOTES
* The board model (TEPNET.DLL), the symbols and artwork (TEPXG24EK.LIB) and the BME280, HC-SR501 and relay models are
made by The Engineering Projects. The source code of the models is not included.
* TEP Boards for Proteus (Arduino Code): its core, the variants and the EEPROM, SPI and Wire libraries are modified
copies of the Arduino AVR core 1.8.6 - GNU Lesser General Public License 2.1 (LGPL 2.1, the text:
LICENSE-LGPL-2.1.txt); its ArduinoBLE and the others and our core files are MIT (LICENSE-MIT.txt).
* The demo sketch uses Adafruit BME280 Library and Adafruit Unified Sensor (BSD, Apache 2.0): install them with the
Library Manager to rebuild.
* Proteus is a product of Labcenter Electronics and is not included. EFR32, xG24 and Silicon Labs are names of Silicon
Laboratories Inc., mikroBUS of MikroElektronika, Qwiic of SparkFun, Arduino of Arduino. The Bluetooth word mark
belongs to Bluetooth SIG. This library is not made or endorsed by them or by Labcenter.
REBUILDING THE FIRMWARE (OPTIONAL)
The HEX file is supplied. Install TEP Boards for Proteus (INSTALLATION step 5), open Arduino
Code\xG24_Smart_Ventilation, select Silicon Labs xG24 Explorer Kit (TEP Proteus) and use Sketch > Export Compiled
Binary. For a real kit use the Silicon Labs Arduino core or Simplicity Studio. Its pins work at 3.3 V.
MODEL SCOPE AND LIMITS
Modelled: D0 .. D6 and A0 .. A7; digital I/O, analogRead 0 .. 1023, PWM (analogWrite), tone and attachInterrupt
through the board model; Serial (the board's monitor), Serial1, Wire and SPI; the two LEDs and the two buttons;
Bluetooth LE as a peripheral.
Not modelled: the EFR32MG24 itself, Thread, Zigbee and Matter, the AI/ML accelerator, the Qwiic port's own I2C bus, the
mikroBUS socket as a part (its signals are the pads), the board as a Bluetooth central. The simulation runs below real
time.
VERSION
TEP xG24 Explorer Kit library V1.0 (Nov 2026). Device XG24 EXPLORER KIT (TEPXG24EK.LIB / TEPNET.DLL), TEP Boards for
Proteus 1.66.0 (adds this board: D0 .. D6, A0 .. A7, LED0 / LED1, BTN0 / BTN1 and Bluetooth LE).
Demo sketch xG24_Smart_Ventilation V1.0. Demo parts: BME280ADVTEP, HCSR501ADVTEP, RELAY1ADVTEP and MOBILE WIFI MONITOR.Development1 release
-
V1.0xG24 Explorer Kit Library for Proteus V1.0this page
V1.0 is the only release in the Download Center so far. When a newer version is published, it appears above with its own download page.
Installation10 steps
From the download to a working project, in order. The steps follow what the package contains.
You will need
- Proteus Design SuiteProteus 8 or newer (Labcenter), on Windows
- Arduino IDE1.8 or 2.x, with the board of the tutorial chosen under Tools → Board
- The compiler named in the tutorialto build the source files into firmware
- Any archive toolWindows, macOS and Linux extract ZIP files on their own
Steps
- 1
Extract the archive
Right-click 8a4d23be1670455794606474ec90d28b.zip and choose Extract All (or open it with 7-Zip or WinRAR) into a folder you can find again. Keep its folder structure (xG24-Explorer-Kit-TEP-v1.0) as it is.
- 2
Copy the library files into Proteus
Move TEPBME280.LIB, TEPHCSR501.LIB and TEPLAPTOP.LIB and 3 more and the files into the LIBRARY folder of your Proteus installation: C:\Program Files (x86)\Labcenter Electronics\Proteus 8 Professional\LIBRARY for Proteus 8, or the matching Proteus 7 folder. Older versions keep it under ProgramData\Labcenter Electronics. If Proteus is open, close it first.
- 3
Add the simulation model
Copy TEPBME280.DLL, TEPHCSR501.DLL and TEPNET.DLL and 1 more into the MODELS folder next to LIBRARY, so the component can run, not only be drawn.
- 4
Restart Proteus and place the component
Start Proteus, open a schematic, press P (Pick Devices) and search for the component by the name used in the tutorial. It appears with its pins ready to wire.
- 5
Install the Arduino library
In the Arduino IDE choose Sketch → Include Library → Add .ZIP Library and pick the library, or copy its folder into Documents\Arduino\libraries. Restart the IDE to see its examples.
- 6
Open the sketch in the Arduino IDE
Open xG24_Smart_Ventilation.ino, eeprom_clear.ino and eeprom_crc.ino and 17 more, select your board and port under Tools, then Verify. Sketch → Export Compiled Binary writes the HEX file a simulation needs.
- 7
Build the source code
Open abi.cpp, Arduino.h and binary.h and 52 more in the compiler named in the tutorial (MikroC, Keil, MPLAB, Code Composer or the Arduino IDE) and build it to get the firmware.
- 8
Load the HEX file
In Proteus double-click the microcontroller, set Program File to xG24_Smart_Ventilation.hex and run the simulation. For real hardware, flash the same file with your programmer.
- 9
Open the example simulation
Open xG24-BLE-Smart-Ventilation.pdsprj in Proteus to see the wiring exactly as in the tutorial. Check the controller's Program File path, then press Play.
- 10
Follow the tutorial
xG24 Explorer Kit Library for Proteus: BLE Smart Fan Simulation explains every connection and setting in order; keep it open beside the files while you build.
FAQs9 questionsContact TEP
How do I download xG24 Explorer Kit Library for Proteus V1.0?
Wait for the 30-second guest countdown on this page, then press the download button; the file comes straight from our storage. Members who are logged in skip the wait. If the browser opens the file instead of saving it, use its Save as option. The download link is made for you when the countdown ends and works for 15 minutes; a saved or shared link stops working, so share this page instead.
What is inside the archive?
xG24 Explorer Kit Library for Proteus V1.0 comes as a ZIP archive of 298 files (4.4 MB, 10.3 MB unpacked) holding Proteus library files, simulation model DLLs, a Proteus simulation, an Arduino sketch, an Arduino library, compiled HEX firmware and source code. Open the File Structure tab for the full list of 298 files.
What should I do if the download does not start?
Check the browser's download list first; an ad blocker or a company firewall can also hold it back, so try another browser or network. If the file arrives incomplete, download it again. For an installation problem, read the Install tab or tell us in the comments with your software version and the exact error message.
Is this file free?
Yes. Every file in the TEP Download Center is free for learning, personal and student projects. If you share it, link back to this page or the tutorial so others find the latest version.
How do I check that the file arrived complete?
Compare its SHA-256 with the one on this page, d37527784a53126b609750df9b99959e75544185285aaca74f2bdf19307ac327. In PowerShell run Get-FileHash "8a4d23be1670455794606474ec90d28b.zip"; on macOS or Linux run shasum -a 256 "8a4d23be1670455794606474ec90d28b.zip". The same value means the file is exactly the one in our storage; a different one means the download broke off, so download it again.
Do I need WinRAR to open the ZIP file?
No. Windows, macOS and Linux open ZIP archives on their own (Extract All, or double-click). WinRAR and 7-Zip work too. Extract the whole archive before using the files.
Where do I put the LIB and IDX files?
Both files go into the LIBRARY folder of your Proteus installation (Proteus 8: C:\Program Files (x86)\Labcenter Electronics\Proteus 8 Professional\LIBRARY; Proteus 7 has the same folder under its own name). Restart Proteus afterwards and search for the component with P.
Which Proteus version does the library need?
The tutorial names the Proteus version the library was made and tested with. Most TEP libraries work in Proteus 7 and Proteus 8; if the component does not appear after a restart, check that both the LIB and the IDX file were copied and that Proteus was fully closed while copying.
How do I get the HEX file into the simulation?
Compile the sketch in the Arduino IDE (Sketch → Export Compiled Binary gives you the HEX next to the sketch), then in Proteus double-click the board, set Program File to that HEX and run.
Members skip the wait. Log in or join TEP.
- 0Total downloads
- 4%Popularity
- ProteusCategory
- 0Comments
- ssyedzainnasirUploaded by
- 19 Nov 2026Uploaded at
d37527784a53126b609750df9b99959e75544185285aaca74f2bdf19307ac327
















Comments
0