Project Files of nRF5340 DK Library for Proteus: Dual-Core Bluetooth LE Simulation
75f1f42380c645e6be34b4e67f9e61f5.zip

nRF5340 DK Library for Proteus V1.0
nRF5340 DK Library for Proteus V1.0 comes as a ZIP archive of 292 files (4.3 MB, 10.0 MB unpacked) holding Proteus library files, simulation model DLLs, a Proteus simulation, an Arduino sketch, an Arduino library, compiled HEX firmware and source code.
- LIBProteus library
- DLLProteus model
- DSNProteus simulation
- INOArduino sketch
- LIBArduino library
- HEXHEX firmware
- SRCSource code
Description
nRF5340-DK-Library-for-Proteus-v1.0.zip with the nRF5340 DK in Proteus (your sketch with the DK's pin names, four LEDs, four buttons, Bluetooth LE to a phone and a serial monitor; TEPNRF5340DK.LIB, TEPNET.DLL and the TEP Boards for Proteus add-on 1.60.0), the soil sensor, LDR, relay and phone libraries, the plant monitor demo with its sketch and a README.
File Structure
7.2 KB1.1 KB7.7 KB11 KB8.5 KB1.5 KB1.7 KB1.9 KB5.7 KB4.9 KB1.1 KB5.8 KB9.6 KB7.2 KB2.5 KB2.1 KB1.9 KB2.1 KB4.4 KB1.1 KB3 KB3 KB1.8 KB2.5 KB3.5 KB149 B2.7 KB2 KB6.4 KB3.2 KB1.3 KB963 B8.6 KB5.9 KB6 KB12 KB1.6 KB1.3 KB14.7 KB4.3 KB6.1 KB20.1 KB8.2 KB2 KB4.5 KB311 B12.8 KB6.7 KB6.1 KB2.2 KB3.4 KB5.9 KB1.5 KB1.6 KB16.6 KB9.7 KB6.9 KB2.1 KB533 B5.7 KB7.4 KB514 B1.7 KB896 B481 B1.4 KB1012 B482 B936 B559 B467 B3.6 KB3.8 KB504 B956 B575 B455 B8.3 KB10.9 KB522 B79 B5.5 KB3.1 KB79 B442 B918 B1.4 KB1.8 KB1 KB1.3 KB1.4 KB1.8 KB1.4 KB5.7 KB502 B463 B5 KB6.5 KB3.4 KB3.4 KB500 B1.6 KB368 B406 B466 B404 B444 B460 B477 B739 B448 B1.3 KB350 B5.7 KB4 KB562 B1.5 KB2 KB550 B7.2 KB4.1 KB371 B4.5 KB3.5 KB492 B390 B478 B6.6 KB2.4 KB479 B5.1 KB1.9 KB1.3 KB1.3 KB750 B1.3 KB490 B2.2 KB1.9 KB498 B1.2 KB1.2 KB487 B5.1 KB4.6 KB371 B1.5 KB1.2 KB478 B6.2 KB3 KB1.5 KB1.7 KB469 B1 KB1.7 KB433 B294 B358 B1.3 KB2.5 KB13.2 KB3.8 KB659 B510 B4.4 KB1.9 KB5.8 KB11 KB835 B518 B6.4 KB2.3 KB29 B436 B9.2 KB4.9 KB439 B4.2 KB1.5 KB9.3 KB7.1 KB4.7 KB2.4 KB388 B5.1 KB893 B667 B1.3 KB5.5 KB2.3 KB1.8 KB468 B882 B530 B791 B487 B894 B2 KB730 B646 B2.6 KB977 B702 B20.6 KB1.8 KB11.8 KB3.2 KB596 B406 B6.3 KB5.7 KB9.3 KB7.7 KB7.7 KB5.8 KB5.9 KB6.4 KB6.4 KB5.3 KB5.6 KB5.7 KB7.9 KB7.7 KB6.5 KB6.3 KB6.2 KB10.3 KB8.5 KB6.6 KB7.6 KB6.7 KB6.1 KB6.7 KB8.3 KB6.2 KB7.2 KB5.9 KB5.6 KB5.7 KB6.7 KB5.9 KB6.2 KB6 KB6 KB6.1 KB6.3 KB6 KB6.1 KB6.2 KB6 KB5.8 KB6.4 KB6.4 KB7 KB6.5 KB6.6 KB6.5 KB5.6 KB7.5 KB7.7 KB7.1 KB5.8 KB5.9 KB5.9 KB6.9 KB5.5 KB5.5 KB7.1 KB5.2 KB29.4 KB25.9 KB1.3 KB8.5 KB34.5 KB60.1 KB39.5 KB289.8 KB13.1 KB39 KB490.4 KB312.5 KB420 KB2.9 MB330 KB34.7 KB28.2 KB312.5 KB420 KB2.9 MB330 KB13.3 KBGallery12 images from the tutorialOpen the tutorial
The circuit, the board and the results as they appear in nRF5340 DK Library for Proteus: Dual-Core Bluetooth LE Simulation. Open an image for its full size.












README
NRF5340 DK LIBRARY FOR PROTEUS - V1.0 (YOUR ARDUINO SKETCH, BLUETOOTH LE TO A PHONE, FOUR LEDS AND FOUR BUTTONS)
Designed by The Engineering Projects
www.TheEngineeringProjects.com
IMPORTANT LINKS
Article (read it first - pictures, step by step, every feature explained):
https://www.theengineeringprojects.com/2026/11/nrf5340-dk-library-for-proteus.html
Report a bug or suggest a feature (our forum):
https://www.theengineeringprojects.com/forum
The demo's other parts are our libraries (included) - their articles:
https://www.theengineeringprojects.com/2026/10/capacitive-soil-moisture-sensor-library-for-proteus-v1-0.html
https://www.theengineeringprojects.com/2026/10/ldr-sensor-library-for-proteus.html
https://www.theengineeringprojects.com/2026/10/relay-module-library-for-proteus-v1-0.html
https://www.theengineeringprojects.com/2026/10/mobile-wifi-monitor-library-for-proteus.html
Support us (the libraries are free):
https://www.theengineeringprojects.com/donate
FILE STRUCTURE
nRF5340-DK-TEP-v1.0/
|-- Proteus Library Files/
| |-- TEPCAPSOIL.LIB 60.1 KB the soil moisture sensor (demo), to LIBRARY
| |-- TEPLAPTOP.LIB 39.5 KB the laptop (demo), to LIBRARY
| |-- TEPLDR.LIB 289.8 KB the LDR light module (demo), to LIBRARY
| |-- TEPMOBILE.LIB 13.1 KB the phone (demo), to LIBRARY
| |-- TEPNRF5340DK.LIB 39.0 KB the nRF5340 DK, to LIBRARY
| |-- TEPRELAY.LIB 490.4 KB the relay (demo), to LIBRARY
|-- Proteus Model Files/
| |-- TEPCAPSOIL.DLL 312.5 KB the soil moisture sensor, to MODELS
| |-- TEPLDR.DLL 420.0 KB the LDR light module, to MODELS
| |-- TEPNET.DLL 2.90 MB the board + monitors + network, to MODELS
| |-- TEPRELAY.DLL 330.0 KB the relay, to MODELS
|-- Arduino Code/
| |-- DK_BLE_Plant_Monitor/DK_BLE_Plant_Monitor.ino 7.2 KB the demo sketch
| |-- TEP Boards for Proteus/hardware/ 1.11 MB the Arduino IDE add-on 1.60.0 (274 files)
|-- Proteus Simulation/
| |-- DK_BLE_Plant_Monitor.hex 34.7 KB the demo sketch (U1)
| |-- nRF5340-DK-BLE-Plant-Monitor.pdsprj 28.2 KB the demo: a Bluetooth LE plant monitor
| |-- TEPCAPSOIL.DLL 312.5 KB copy of the model
| |-- TEPLDR.DLL 420.0 KB copy of the model
| |-- TEPNET.DLL 2.90 MB copy of the model
| |-- TEPRELAY.DLL 330.0 KB copy of the model
|-- README.txt ~12.1 KB this file
Total: 9.98 MB (unzipped). The source code of the models is not included.
WHAT IS IT?
Proteus 8 has no nRF5340 processor model, so this is NOT a real nRF5340 chip. Our team has put a lot of effort into
building this board ourselves: it is Nordic Semiconductor's nRF5340 DK (PCA10095) - the blue development kit with the
dual-core nRF5340 SoC, its PCB antenna, the interface MCU with its USB port, the power switch, four green LEDs and four
buttons - drawn compact, and it runs YOUR Arduino sketch in Proteus:
* You write a normal sketch for the DK's Arduino header (D0 .. D13, A0 .. A5, SDA, SCL; analogRead 0-1023,
analogWrite, attachInterrupt, tone, Wire, SPI, Serial, Serial1) and compile it in the Arduino IDE with our board
package "TEP Boards for Proteus" 1.60.0 (in Arduino Code - see INSTALLATION).
* LED1 .. LED4 light when LOW, as on the real DK (LED_BUILTIN is LED1). BUTTON1 .. BUTTON4 read LOW while you hold
them: click a button on the board in the running simulation.
* Bluetooth LE works through ArduinoBLE: the board advertises as a peripheral with your services and
characteristics, and our Mobile WiFi Monitor's Bluetooth app is the central (it lists the board, connects, reads,
writes and gets the notifications).
TEP additions: the USB port opens the serial monitor (the same window as our TEP Serial Monitor Advance).
Limits (say them before you start): one phone is the central; the board cannot be a central itself. Your sketch is
one program (the real chip's two cores are not split). LE Audio, Thread, Zigbee, NFC, USB device classes and the QSPI
flash are drawn, not modelled.
Your sketch gets 8 KB of RAM in the simulation (the real one: 512 KB), about 256 KB of flash, and int is 16 bits in
the simulation (use long for big numbers). See MODEL SCOPE AND LIMITS.
ONE DEVICE (search "NRF5340" in Pick Devices):
NRF5340 DK "nRF5340 DK" V1.0 (Microprocessor ICs > Bluetooth Boards), prefix U, model TEPNET.DLL.
Its TEP window has no Windows title bar: the serial monitor (the USB port, 115200 baud: Monitor, Plotter and Board
tabs).
The same TEPNET.DLL also runs our other sketch boards and the phone; it replaces any older TEPNET.DLL (keep only this
newest one in MODELS).
TEST STATUS
V1.0: verified in Proteus 8.5 on 17 Nov 2026 with the demo project as shipped. What the Proteus run showed:
* nRF5340-DK-BLE-Plant-Monitor: the banner, "Advertising as "nRF5340 DK Plant"" with the board's address and the button
help; LED1 blinked. The soil sensor settled in about 3 s (100, 94, 81, 78 %), then "Sensors: soil raw 479 (air 790,
water 395), light raw 200" and "Soil 78 % light 81 % limit 30 % pump OFF auto" every second.
* The phone's Bluetooth app listed nRF5340 DK Plant; Connect: ">> Phone connected", LED1 on, and the phone showed the
soil, the light, the dry limit, the pump and the auto mode.
* BUTTON4: "auto mode OFF (manual)". BUTTON1: "Pump ON (BUTTON1)", LED3 and the relay on, 4 s later "Pump OFF
(watered)". BUTTON3 twice: "dry limit 35 %", "dry limit 40 %". BUTTON4: "auto mode ON".
* The soil sensor's pop-up, DRY: the soil fell to 19 % and LED2 lit; when the 15 s rest after the hand watering was
over: "Pump ON (the soil is dry)", 4 s later "Pump OFF (watered)"; the phone followed.
* The LDR's pop-up, Night: "light 0 %" and LED4 on.
* about 52 s of simulation, no errors, with the sensors' and the relay's windows, the phone and the monitor open.
INSTALLATION (about 3 minutes)
1. Close Proteus. Extract the WHOLE ZIP to a normal folder (e.g. Desktop).
2. Copy everything in "Proteus Library Files" to the LIBRARY folder of Proteus, for example:
C:\Program Files (x86)\Labcenter Electronics\Proteus 8 Professional\LIBRARY
(on some PCs: C:\ProgramData\Labcenter Electronics\Proteus 8 Professional\LIBRARY). TEPNRF5340DK.LIB is the board;
the others are the demo's parts: TEPCAPSOIL.LIB, TEPLDR.LIB, TEPRELAY.LIB, TEPMOBILE.LIB and TEPLAPTOP.LIB.
3. Copy the DLLs from "Proteus Model Files" (TEPNET.DLL, TEPCAPSOIL.DLL, TEPLDR.DLL, TEPRELAY.DLL) to the MODELS
folder (...\Proteus 8 Professional\MODELS) -
replace an older TEPNET.DLL (this one is the first that knows this board).
4. Delete TEPNRF5340DK.IDX from the LIBRARY folder if it is there.
5. The Arduino IDE (only to compile your own sketches - the demo has its HEX file): copy the folder
"Arduino Code\TEP Boards for Proteus\hardware" into your sketchbook folder (normally Documents\Arduino), so that
Documents\Arduino\hardware\tep\avr\boards.txt exists (replace an older copy); restart the IDE. The Arduino AVR Boards
platform must be installed (it comes with IDE 1.8.x; in IDE 2.x install "Arduino AVR Boards" from the Boards
Manager once).
Tools > Board > TEP Boards for Proteus > Nordic nRF5340 DK (TEP Proteus). ArduinoBLE is in the board package; the
demo needs no other library.
6. Start Proteus. In Pick Devices (P) search "NRF5340".
RUN THE DEMO
Keep the .hex file and the DLLs beside the project in "Proteus Simulation".
nRF5340-DK-BLE-Plant-Monitor.pdsprj - U1 the nRF5340 DK (DK_BLE_Plant_Monitor.hex) is a Bluetooth LE plant monitor:
U2 = the capacitive soil moisture sensor (Advance) on A0, U3 = the LDR light module (Advance) on A1, RLY1 = the pump's
relay (Advance) on D7, MOB1 = the phone (Mobile WiFi Monitor), the central.
Press Run. The monitor prints "Advertising as "nRF5340 DK Plant"" and LED1 blinks; a line every second gives the soil,
the light, the dry limit, the pump and the mode. On the phone open the Bluetooth app and click Connect: LED1 stays on
and the phone shows the soil, the light, the dry limit, the pump and the auto mode.
Click the buttons on the board: BUTTON1 waters for 4 s (LED3 and the relay), BUTTON2 / BUTTON3 move the dry limit 5 %
down / up, BUTTON4 switches the auto mode. On the soil sensor's pop-up click DRY: LED2 lights and, in auto mode, the
pump waters by itself (then rests 15 s). On the LDR's pop-up make it dark: LED4 lights. On the phone write the Pump
row (1) to water, the Dry limit row to set the limit, the Auto mode row (0 / 1).
Closed a window? The USB port opens the monitor, the OPEN PANEL pads open the sensors and the relay, a click on the
phone's screen the phone.
THE PINS (the label on the part, what it can do in the simulation)
D0, D1 Serial1 RX and TX, or GPIO (the real DK: P1.00, P1.01)
D2 .. D13 GPIO, PWM (analogWrite), interrupt; D10 .. D13 SPI (SS, MOSI, MISO, SCK)
A0 .. A5 analogRead 0 .. 1023 for 0 .. 3.3 V, or GPIO (the core's numbers 14 .. 19)
SDA, SCL Wire (the real DK: P1.02, P1.03)
VDD, 5V, GND 3.3 V (the logic), 5 V, ground; RESET the board's reset (the RESET button too)
AREF, VIN drawn, not modelled
LED1 .. LED4 (22 .. 25) are the green LEDs, lit when LOW; LED_BUILTIN is LED1, with LED_BUILTIN_ACTIVE and
LED_BUILTIN_INACTIVE. BUTTON1 .. BUTTON4 (26 .. 29) are the buttons, LOW when pressed (pinMode INPUT_PULLUP);
BTN_BUILTIN is BUTTON1. Serial is the USB: the board's built-in monitor. The pin header follows the real DK's
Arduino Uno layout; pins_arduino.h lists the real P0 / P1 GPIO of each pin.
PROPERTIES (double-click the part > Edit Properties)
PROGRAM the sketch's HEX (Arduino IDE: Sketch > Export Compiled Binary with Nordic nRF5340 DK (TEP Proteus))
MONITOR YES = the built-in serial monitor on Serial; BAUD its speed (115200, or AUTO)
AUTOOPEN YES = the monitor window opens at Run (the demo: YES)
TROUBLESHOOTING
* The phone's list is empty: call BLE.begin(), set a local name and BLE.advertise(); call BLE.poll() in loop(). The
phone needs this TEPNET.DLL or newer.
* The soil reads 100 % for the first seconds: the capacitive sensor settles after power-up, as a real one does.
* The pump runs backwards: the relay module switches on when IN is LOW (the sketch writes HIGH before OUTPUT).
* A button does nothing: use pinMode(BUTTONx, INPUT_PULLUP) and act when digitalRead() is LOW.
* The LEDs look inverted: they light when the pin is LOW, as on the real DK.
* An integer goes wrong above 32767: int is 16 bits in the simulation - use long.
BUG REPORTS AND FEATURE REQUESTS
Please post them in our forum with a screenshot and the Serial Monitor text:
https://www.theengineeringprojects.com/forum
LICENCES AND THIRD-PARTY NOTES
* The board model (TEPNET.DLL), the symbols and artwork (TEPNRF5340DK.LIB) and the soil sensor, LDR and relay models
are made by The Engineering Projects. The source code of the models is not included.
* TEP Boards for Proteus (Arduino Code): its core, the variants and the EEPROM, SPI and Wire libraries are modified
copies of the Arduino AVR core 1.8.6 - GNU Lesser General Public License 2.1 (LGPL 2.1, the text:
LICENSE-LGPL-2.1.txt); its WiFi, WebServer, ArduinoBLE, the sensor libraries and the others and our core files are
MIT (LICENSE-MIT.txt).
* Our ArduinoBLE has the calls of the library of that name; its code is ours.
* Proteus is a product of Labcenter Electronics and is not included. nRF5340 and Nordic Semiconductor are names of
Nordic Semiconductor ASA, Arduino of Arduino. The Bluetooth word mark belongs to Bluetooth SIG. This library is not
made or endorsed by them or by Labcenter.
REBUILDING THE FIRMWARE (OPTIONAL)
The HEX file is supplied. Install TEP Boards for Proteus (INSTALLATION step 5), open Arduino
Code\DK_BLE_Plant_Monitor, select Nordic nRF5340 DK (TEP Proteus) and use Sketch > Export Compiled Binary. For a
real board use Nordic's nRF Connect SDK (the application core runs your code, the network core the Bluetooth
controller). Its pins work at 3.3 V.
MODEL SCOPE AND LIMITS
Modelled: the DK's Arduino header; digital I/O, analogRead 0 .. 1023, PWM (analogWrite), tone and attachInterrupt
through the board model; Serial (the board's monitor), Serial1, Wire and SPI; the four LEDs, the four buttons and
RESET; Bluetooth LE as a peripheral (ArduinoBLE) with the phone as the central.
Not modelled: the nRF5340 itself and its two cores, the radio's range, LE Audio, Thread, Zigbee, 802.15.4, NFC, USB
device classes, the QSPI flash, the current measurement header, the board as a central. The simulation runs below
real time.
VERSION
TEP nRF5340 DK library V1.0 (Nov 2026). Device NRF5340 DK (TEPNRF5340DK.LIB / TEPNET.DLL), TEP Boards for Proteus
1.60.0 (adds this board: LED1 .. LED4, BUTTON1 .. BUTTON4).
Demo sketch DK_BLE_Plant_Monitor V1.0. Demo parts: CAPSOILADVTEP, LDRADVTEP, RELAY1ADVTEP and MOBILE WIFI MONITOR.Development1 release
-
V1.0nRF5340 DK Library for Proteus V1.0this page
V1.0 is the only release in the Download Center so far. When a newer version is published, it appears above with its own download page.
Installation10 steps
From the download to a working project, in order. The steps follow what the package contains.
You will need
- Proteus Design SuiteProteus 8 or newer (Labcenter), on Windows
- Arduino IDE1.8 or 2.x, with the board of the tutorial chosen under Tools → Board
- The compiler named in the tutorialto build the source files into firmware
- Any archive toolWindows, macOS and Linux extract ZIP files on their own
Steps
- 1
Extract the archive
Right-click 75f1f42380c645e6be34b4e67f9e61f5.zip and choose Extract All (or open it with 7-Zip or WinRAR) into a folder you can find again. Keep its folder structure (nRF5340-DK-TEP-v1.0) as it is.
- 2
Copy the library files into Proteus
Move TEPCAPSOIL.LIB, TEPLAPTOP.LIB and TEPLDR.LIB and 3 more and the files into the LIBRARY folder of your Proteus installation: C:\Program Files (x86)\Labcenter Electronics\Proteus 8 Professional\LIBRARY for Proteus 8, or the matching Proteus 7 folder. Older versions keep it under ProgramData\Labcenter Electronics. If Proteus is open, close it first.
- 3
Add the simulation model
Copy TEPCAPSOIL.DLL, TEPLDR.DLL and TEPNET.DLL and 1 more into the MODELS folder next to LIBRARY, so the component can run, not only be drawn.
- 4
Restart Proteus and place the component
Start Proteus, open a schematic, press P (Pick Devices) and search for the component by the name used in the tutorial. It appears with its pins ready to wire.
- 5
Install the Arduino library
In the Arduino IDE choose Sketch → Include Library → Add .ZIP Library and pick the library, or copy its folder into Documents\Arduino\libraries. Restart the IDE to see its examples.
- 6
Open the sketch in the Arduino IDE
Open DK_BLE_Plant_Monitor.ino, eeprom_clear.ino and eeprom_crc.ino and 17 more, select your board and port under Tools, then Verify. Sketch → Export Compiled Binary writes the HEX file a simulation needs.
- 7
Build the source code
Open abi.cpp, Arduino.h and binary.h and 52 more in the compiler named in the tutorial (MikroC, Keil, MPLAB, Code Composer or the Arduino IDE) and build it to get the firmware.
- 8
Load the HEX file
In Proteus double-click the microcontroller, set Program File to DK_BLE_Plant_Monitor.hex and run the simulation. For real hardware, flash the same file with your programmer.
- 9
Open the example simulation
Open nRF5340-DK-BLE-Plant-Monitor.pdsprj in Proteus to see the wiring exactly as in the tutorial. Check the controller's Program File path, then press Play.
- 10
Follow the tutorial
nRF5340 DK Library for Proteus: Dual-Core Bluetooth LE Simulation explains every connection and setting in order; keep it open beside the files while you build.
FAQs9 questionsContact TEP
How do I download nRF5340 DK Library for Proteus V1.0?
Wait for the 30-second guest countdown on this page, then press the download button; the file comes straight from our storage. Members who are logged in skip the wait. If the browser opens the file instead of saving it, use its Save as option. The download link is made for you when the countdown ends and works for 15 minutes; a saved or shared link stops working, so share this page instead.
What is inside the archive?
nRF5340 DK Library for Proteus V1.0 comes as a ZIP archive of 292 files (4.3 MB, 10.0 MB unpacked) holding Proteus library files, simulation model DLLs, a Proteus simulation, an Arduino sketch, an Arduino library, compiled HEX firmware and source code. Open the File Structure tab for the full list of 292 files.
What should I do if the download does not start?
Check the browser's download list first; an ad blocker or a company firewall can also hold it back, so try another browser or network. If the file arrives incomplete, download it again. For an installation problem, read the Install tab or tell us in the comments with your software version and the exact error message.
Is this file free?
Yes. Every file in the TEP Download Center is free for learning, personal and student projects. If you share it, link back to this page or the tutorial so others find the latest version.
How do I check that the file arrived complete?
Compare its SHA-256 with the one on this page, 7a98b0adf4929f8dc2d5950f47d2764a1e45355ae34880707a11c9fb1297298f. In PowerShell run Get-FileHash "75f1f42380c645e6be34b4e67f9e61f5.zip"; on macOS or Linux run shasum -a 256 "75f1f42380c645e6be34b4e67f9e61f5.zip". The same value means the file is exactly the one in our storage; a different one means the download broke off, so download it again.
Do I need WinRAR to open the ZIP file?
No. Windows, macOS and Linux open ZIP archives on their own (Extract All, or double-click). WinRAR and 7-Zip work too. Extract the whole archive before using the files.
Where do I put the LIB and IDX files?
Both files go into the LIBRARY folder of your Proteus installation (Proteus 8: C:\Program Files (x86)\Labcenter Electronics\Proteus 8 Professional\LIBRARY; Proteus 7 has the same folder under its own name). Restart Proteus afterwards and search for the component with P.
Which Proteus version does the library need?
The tutorial names the Proteus version the library was made and tested with. Most TEP libraries work in Proteus 7 and Proteus 8; if the component does not appear after a restart, check that both the LIB and the IDX file were copied and that Proteus was fully closed while copying.
How do I get the HEX file into the simulation?
Compile the sketch in the Arduino IDE (Sketch → Export Compiled Binary gives you the HEX next to the sketch), then in Proteus double-click the board, set Program File to that HEX and run.
Members skip the wait. Log in or join TEP.
- 0Total downloads
- 4%Popularity
- ProteusCategory
- 0Comments
- ssyedzainnasirUploaded by
- 18 Nov 2026Uploaded at
7a98b0adf4929f8dc2d5950f47d2764a1e45355ae34880707a11c9fb1297298f





















Comments
0