TEP DOWNLOAD CENTER

Project Files of Dual-Axis Solar Tracker Library for Proteus Simulation

Libraries Code Projects Simulation
tep://download-terminal f993d1cb82664907827183cb4377fa41.zip ZIP archiveV1.0Verified0 downloadsFree
Dual-Axis Solar Tracker Library for Proteus Simulation: an Arduino UNO V4.0 with the solar tracker, its panel turned to the sun
Proteus library · File 1 of 1

Dual-Axis Solar Tracker Library for Proteus V1.0

Dual-Axis Solar Tracker Library for Proteus V1.0 comes as a ZIP archive of 10 files (1.2 MB, 2.7 MB unpacked) holding Proteus library files, simulation model DLLs, a Proteus simulation, an Arduino sketch and compiled HEX firmware.

  • LIBProteus library
  • DLLProteus model
  • DSNProteus simulation
  • INOArduino sketch
  • HEXHEX firmware

Description

Dual-Axis-Solar-Tracker-Library-for-Proteus-v1.0.zip with the dual-axis solar tracker for Proteus simulation (TEPTRACKER.LIB and TEPTRACKER.DLL), our Arduino UNO V4.0, the A4 demo with its sketch and a README.

Read Dual-Axis Solar Tracker Library for Proteus Simulation

File Structure

f993d1cb82664907827183cb4377fa41.zip10 files · 5 folders · 2.7 MB unpacked
Dual-Axis-Solar-Tracker-TEP-v1.0/10 files · 2.7 MB
Arduino Code/1 file · 5.1 KB
SolarTracker_Demo/1 file · 5.1 KB
INO SolarTracker_Demo.inoArduino sketch 5.1 KB
Proteus Library Files/2 files · 228 KB
LIB ArduinoV4TEP.LIBProteus library 201.9 KB
LIB TEPTRACKER.LIBProteus library 26 KB
Proteus Model Files/2 files · 1.2 MB
DLL TEPARDUINO.DLLSimulation model 883.5 KB
DLL TEPTRACKER.DLLSimulation model 340.5 KB
Proteus Simulation/4 files · 1.2 MB
DSN Dual-Axis-Solar-Tracker-ArduinoUnoV4.pdsprjProteus simulation 19.9 KB
HEX SolarTracker_Demo.hexCompiled HEX file 23.4 KB
DLL TEPARDUINO.DLLSimulation model 883.5 KB
DLL TEPTRACKER.DLLSimulation model 340.5 KB
TXT README.txtText file 17.9 KB

README

README.txt 319 lines
DUAL-AXIS SOLAR TRACKER LIBRARY FOR PROTEUS SIMULATION - V1.0 (two servos, four LDRs, a solar panel, a pop-up)
Designed by The Engineering Projects
www.TheEngineeringProjects.com

IMPORTANT LINKS
Article (read it first - pictures, step by step, every feature explained):
  https://www.theengineeringprojects.com/2026/11/dual-axis-solar-tracker-library-for-proteus.html
Report a bug or suggest a feature (our forum):
  https://www.theengineeringprojects.com/forum/category/motor-driver-proteus-library
The demo runs on our Arduino UNO V4.0 (included) - working LEDs, RESET and a
built-in serial monitor, no Virtual Terminal to wire - its own article:
  https://www.theengineeringprojects.com/2026/10/arduino-uno-library-for-proteus-v40.html
The demo sketch uses the Servo library that comes with the Arduino IDE (nothing to install).
  
Support us (the libraries are free):
  https://www.theengineeringprojects.com/donate

FILE STRUCTURE
Dual-Axis-Solar-Tracker-TEP-v1.0/
|-- Proteus Library Files/
|   |-- ArduinoV4TEP.LIB                              201.9 KB   TEP Arduino boards V4.0 (UNO) -> LIBRARY
|   |-- TEPTRACKER.LIB                                 26.0 KB   the library -> LIBRARY folder
|-- Proteus Model Files/
|   |-- TEPARDUINO.DLL                                883.5 KB   the Arduino board model -> MODELS folder
|   |-- TEPTRACKER.DLL                                340.5 KB   the model -> MODELS folder
|-- Proteus Simulation/
|   |-- Dual-Axis-Solar-Tracker-ArduinoUnoV4.pdsprj    19.9 KB   the demo project
|   |-- SolarTracker_Demo.hex                          23.4 KB   the demo firmware
|   |-- TEPARDUINO.DLL                                883.5 KB   copy of the board model
|   |-- TEPTRACKER.DLL                                340.5 KB   copy of the model
|-- Arduino Code/
|   |-- SolarTracker_Demo/SolarTracker_Demo.ino         5.1 KB   the demo sketch (source of the .hex)
|-- README.txt                                        ~19.2 KB   this file
Total: 2.68 MB (unzipped). The C++ source code of the models is not included.

WHAT IS IT?
A small dual-axis solar tracker of the hobby kind: a base, a pan servo, a post with the tilt servo,
a 6 V 1 W solar panel
(110 x 60 mm) and a head of four LDRs behind a shade cross - seen from the south and from above. It
is drawn small and
compact, at a quarter of the real size (our own drawing, no maker's mark). What the model does:
  * The sun moves through the sky by the solar time (HOUR, running SPEED times faster than the
    simulation), the LATITUDE
    and the DAY of the year. A clear sky gives up to about 900 W/m2 straight from the sun and a
    tenth of that from the
    sky; a CLOUDY sky gives 3 % of the direct light.
  * PAN and TILT take servo pulses, 544 to 2400 us for 0 to 180 degrees - what the Arduino Servo
    library sends. Each servo
    turns at up to 600 degrees a second and holds its place when the pulses stop. Pan 0 = the panel
    looks east, 90 south,
    180 west. Tilt 0 = the panel stands upright and looks at the horizon, 90 = it lies flat and
    looks straight up.
  * TL, TR, BL, BR are the four LDRs (top / bottom, left / right as seen from the front of the
    panel), each from VCC with
    1 kohm to GND on the head: a brighter LDR gives a higher voltage. The cross between them throws
    its shade on the
    LDRs that are away from the sun: an LDR is fully shaded when the sun stands 14 degrees to the
    other side. A grey cap
    lets 1 % of the light through, so that the LDRs do not saturate in full sun. They need 30 ms to
    follow the light.
  * PV+ and PV- are the panel: 7.2 V open, 0.18 A shorted and 1.0 W at 6.0 V in full sun. Its light
    is the direct light
    times the cosine of its angle to the sun, plus the sky's light.
  * VCC and GND: 5 V for the servos (6 mA each at rest, up to 0.25 A each while turning) and the
    LDRs.
  * On the sheet the panel TURNS as the servos turn it; the base shows the pan and tilt angles, a
    status line with the
    panel's watts and a LOCK lamp (ours). Click it at Run for the pop-up: the sky with the sun's
    path, the sun and the
    panel's aim, the four LDRs with their volts, eight live values, the light caught against a fixed
    panel; graphs, an
    event log and a check page.
The body is drawn as on the real part and to true scale against our Arduino.
The TEP signature and the pop-up are TEP additions.

ONE DEVICE (search "TRACKER" or "SOLAR" in Pick Devices):
  SOLARTRACKERTEP  "Dual-Axis Solar Tracker V1.0" in TEPTRACKER.LIB (Electromechanical > Solar
  Trackers), prefix ST,
                   model TEPTRACKER.DLL (mixed: analog and digital). Ten pins: on the left TL, TR,
                   BL, BR (the LDR
                   outputs) and PAN, TILT (the servo signals); on the right VCC, GND and PV+, PV-
                   (the panel).

THE POP-UP
Click the part at Run. Tabs:
    Tracker    chips: the sky (Clear, Cloudy), the day (21 March, 21 June, 21 December) and the
    clock (x 1, x 3600,
               x 7200). The sky as a map with the sun's path of the day, the sun, the panel's aim
               and the aim of a fixed
               panel; the four LDRs from the front, each as bright as its light, with its volts and
               lux; eight live
               values: the sun, the panel's pan and tilt, the angle off the sun, the light on the
               panel, the panel's
               output, the two servo pulses, the light caught today against a fixed panel, the 5 V
               supply.
    Graphs     the live values over the last 2, 6 or 15 s. Live / Freeze.
    Event log  every change and warning; filters All / Changes / Warnings, Pause, Clear
    Check      what the part is doing and what to look at, each with a verdict (green = fine, amber
    = check, red = wrong)
    Settings   theme, text size, open at Run, window size
    Help       report a bug, suggest a feature, article, updates, donate, forum; Copy diagnostics
    for a bug report

TEST STATUS
V1.0: verified in Proteus 8.5 on 16 Nov 2026 (the demo project as shipped: an A4 sheet, an Arduino UNO V4.0).
What the runs showed (the model's own numbers and the sketch's monitor):
The demo as shipped (SolarTracker_Demo; ST1 HOUR 6, SPEED 3600, LATITUDE 30, DAY 81, SKY CLEAR, PAN0
90, TILT0 45; R1
33 ohm, the panel's load; R2 and R3 10 k, half of the panel's voltage to A4), one run (trkfinal3),
the model's pauses:
  * The panel starts at pan 90, tilt 45. It is dark at the first step, so the sketch turns it east
    (pan 0, tilt 20).
    ON THE SUN at 06:20 (the Event log: the panel within 5.0 deg of the sun; pan 0, tilt 9; the sun
    at 93 / 4 deg).
  * 06:30 (0.5 s): the sun at 94 deg, 6 deg up; the panel looks to 92 deg, 3 deg up, 4.1 deg off; TL
    2.29 V, TR 2.16
    V, BL 2.11 V, BR 1.98 V; 334 W/m2 on the panel, 1.97 V, 0.12 W.
  * 10:00 (4 s): the sun at 131 deg, 49 deg up; pan 39, tilt 46, 3.0 deg off; the LDRs 3.03 to 3.25
    V; 964 W/m2, 5.53
    V, 0.93 W. On the sheet the panel is turned, the base shows 39 and 46 and 0.93 W, the lamp is
    green and the UNO's
    LED is lit.
  * 12:00 (6 s): the sun at 180 deg, 60 deg up; pan 86, tilt 58, 3.1 deg off; 1003 W/m2, 5.69 V,
    0.98 W; 4774 Wh/m2
    caught so far, a fixed panel 3603 (+32 %).
  * 15:00 (9 s, the Event log): the sun at 243 deg, 38 deg up, the panel 2.5 deg off, 905 W/m2 on it
    (a fixed panel
    664), 0.84 W.
  * 17:30 (11.5 s): the sun at 266 deg, 6 deg up; pan 174, tilt 8, 2.8 deg off; 334 W/m2, 1.97 V,
    0.12 W; 9471 Wh/m2
    against 7189 (+32 %).
  * SUNSET at 18:00 at azimuth 270 deg, then NIGHT: the sketch parks the panel east (pan 0, tilt
    20).
  * In all (the Check page at 19:00): 9557 Wh/m2 caught, a fixed panel (south, tilted 30 deg) 7204
    Wh/m2: +33 %; on
    the sun 11.7 of 12.0 hours; the most it was off while on the sun 4.8 deg; the most power 0.98 W;
    8436 mWh out of
    the panel.
  * The Event log, hour by hour (W/m2 on the tracker's panel / on a fixed panel): 07:00 563 / 184,
    08:00 794 / 434,
    09:00 904 / 665, 10:00 964 / 848, 11:00 994 / 964, 12:00 1003 / 1005, 13:00 995 / 964, 14:00 964
    / 848, 15:00 905
    / 664, 16:00 794 / 433, 17:00 563 / 184.
  * The monitor (a line every 1000 ms = an hour): DARK at 06:00 (pan 0, tilt 20); 07:00 pan 6, tilt
    13, 3.48 V, 0.37
    W, ON THE SUN; 12:00 pan 89, tilt 58, 5.70 V, 0.98 W; 17:00 pan 172, tilt 14, 3.15 V, 0.30 W;
    DARK at 18:00. 117 s
    for the 13 s of the run.
A second run under a cloudy sky (trkcloud3: SKY CLOUDY), at 12:00: OFF THE SUN, the panel 73 deg
away from it (pan 2,
tilt 19); the four LDRs 1.94 to 1.97 V; 216 W/m2 on the panel, 1.27 V, 0.05 W; 843 Wh/m2 caught, a
fixed panel 841.
A third run on 21 June (trksum3: DAY 172, PAN0 0, TILT0 20), at 07:00: the sun at 76 deg, 24 deg up;
pan 0 (its stop),
tilt 26; the panel 13.2 deg off the sun; TL 1.36 V, TR 2.92 V, BL 1.39 V, BR 3.04 V; 753 W/m2, 4.42
V, 0.59 W.

INSTALLATION (about 2 minutes)
1. Close Proteus. Extract the WHOLE ZIP to a normal folder (e.g. Desktop).
2. Copy everything in "Proteus Library Files" (TEPTRACKER.LIB and our Arduino library V4.0,
ArduinoV4TEP.LIB, with the ARDUINO UNO V4.0 used by the demo) to the LIBRARY folder of Proteus, for
example:
     C:\Program Files (x86)\Labcenter Electronics\Proteus 8 Professional\LIBRARY
   (use the folder that already holds Proteus's own .LIB files).
3. Copy TEPTRACKER.DLL and TEPARDUINO.DLL from "Proteus Model Files" to the MODELS folder
(...\Proteus 8 Professional\MODELS).
4. Delete TEPTRACKER.IDX from the LIBRARY folder if it is there (Proteus makes a new index).
5. Start Proteus. In Pick Devices (P) search "TRACKER".

RUN THE DEMO
"Proteus Simulation\Dual-Axis-Solar-Tracker-ArduinoUnoV4.pdsprj" (an A4 sheet) - keep the .hex file
and the DLLs beside the project.
  A sun tracker:
  ARD1:   Arduino UNO V4.0 running SolarTracker_Demo.hex, its serial monitor built in (window "TEP
  Arduino UNO - ARD1").
  ST1:    the tracker: 21 March at latitude 30, the day starts at 06:00, SPEED 3600 (an hour each
  second); the
          panel starts facing south at 45 degrees. TL, TR, BL, BR to A0 - A3; PAN to D9, TILT to
          D10; VCC and GND on
          the supply rails; PV- on ground.
  R1:     33 ohm, the panel's load, from PV+ to ground.
  R2, R3: 10 k each: half of the panel's voltage to A4.
          Twenty times a second the sketch compares the LDRs in pairs - the two left against the two
          right for the pan
          servo, the two upper against the two lower for the tilt servo - and turns each servo
          towards the brighter
          pair, up to 6 degrees a step; the pan step grows as the panel lies flatter. In the dark it
          parks the panel
          facing east. The UNO's LED lights while the panel is on the sun; the monitor prints the
          four LDRs, the two
          angles and the panel's volts and watts.
Closed the monitor? Click the UNO's USB port.

WIRING (the same in Proteus and on a real board)
  The four LDR outputs to four analog inputs; PAN and TILT to two pins that the Servo library
  drives; VCC to 5 V, GND to
  ground. Take the panel's power from PV+ and PV-. To measure it with a 5 V board, divide its
  voltage (it can reach
  7.2 V): two equal resistors halve it. A real tracker's servos need their own 5 V supply, not the
  Arduino's 5 V pin.
REAL HARDWARE:
 * Bare LDRs saturate in full sun: their resistance falls to a few tens of ohms and all four read
   the same. Real
   trackers shade them, put them in tubes or under a grey filter - ours has a grey cap.
 * Give the servos their own 5 V supply (each can draw 0.65 A when it stalls) and join the grounds.
 * A tracker gains most in the morning and the evening. On a small panel the two servos can use more
   energy than the
   tracking wins: move in steps and rest in between, as the big trackers do.
 * Under clouds the LDRs read alike. Do not let the tracker hunt: keep the last position or go to a
   rest position.
 * Wind: a tilted panel is a sail. Big trackers lay the panel flat in a storm.

THE DEMO SKETCH ON THE SERIAL MONITOR (SolarTracker_Demo V1.0, 9600 baud)
The sketch reports every 1000 ms (an hour of the demo's day). Type a command:
  park       stop tracking and hold the panel like a fixed one (south, 60 degrees)       track
  track again
  rate 500   report every 500 ms                                                         help
EXPECTED MONITOR OUTPUT
  Sun tracker - The Engineering Projects
  Commands: park | track | rate 1000 | help
  TL 40 TR 41 BL 40 BR 40 | pan 0 tilt 20 | 0.04 V 0.00 W  DARK
  TL 575 TR 552 BL 549 BR 526 | pan 6 tilt 13 | 3.48 V 0.37 W  ON THE SUN
  TL 634 TR 609 BL 602 BR 578 | pan 15 tilt 25 | 4.72 V 0.68 W  ON THE SUN
  ...
  TL 672 TR 647 BL 649 BR 624 | pan 89 tilt 58 | 5.70 V 0.98 W  ON THE SUN
  ...
  TL 542 TR 515 BL 571 BR 543 | pan 172 tilt 14 | 3.15 V 0.30 W  ON THE SUN
  TL 56 TR 53 BL 62 BR 58 | pan 0 tilt 20 | 0.01 V 0.00 W  DARK

PROPERTIES (double-click the part > Edit Properties)
  Solar time at the start (HOUR)       0 - 24 hours (6)
  Clock (SPEED)                        1 real time, 3600 an hour each simulated second, 1 - 14400
  (3600)
  Latitude (LATITUDE)                  0 - 66 degrees north (30)
  Day of the year (DAY)                1 - 365: 81 = 21 March, 172 = 21 June, 355 = 21 December (81)
  The sky (SKY)                        CLEAR or CLOUDY (CLEAR)
  Pan at the start (PAN0)              0 - 180 degrees: 0 east, 90 south, 180 west (90)
  Tilt at the start (TILT0)            0 - 180 degrees: 0 upright, 90 flat (45)
Every run starts again from the properties.

LINKS.INI (OPTIONAL)
The Help page cards of the pop-up open web pages. To point them somewhere else without a new DLL,
put a text file named links.ini next to TEPTRACKER.DLL with lines KEY=URL, for example:
  ARTICLE=https://www.theengineeringprojects.com/...
Keys: WEBSITE, FORUM, BUG_REPORT, FEATURE_REQUEST, ARTICLE, USER_GUIDE,
UPDATE_CHECK, DONATE. Only http:// and https:// links are used; lines starting
with # are comments.

TROUBLESHOOTING
* The panel does not move: no servo pulses on PAN / TILT (the pop-up says NO SIGNAL), or no 5 V on
  VCC (NO SUPPLY).
* It turns away from the sun: the LDR pairs are swapped in the sketch. A brighter LDR gives a HIGHER
  voltage here; TL is
  the top left one as seen from the front of the panel.
* It hunts to and fro: the steps are too large or too fast for the LDRs (30 ms) - use smaller steps
  or a dead band.
* It stays off the sun under a cloudy sky: the four LDRs read alike; that is how a real LDR tracker
  behaves.
* It cannot follow in the early morning of a summer day: the sun rises north of east, beyond the pan
  servo's 0 degree
  stop.
* The watts look low at noon: the load does not suit the panel. About 36 ohm takes the most in full
  sun.
* The part is not simulated: TEPTRACKER.DLL is missing from MODELS and from the project folder.
* The part is not simulated: TEPTRACKER.DLL is missing from MODELS and from the project folder. No
  UNO / no monitor window: TEPARDUINO.DLL is missing, or click the UNO's USB port.

BUG REPORTS AND FEATURE REQUESTS
Please post them in our forum with a screenshot, the Serial Monitor text, the
simulation log and the pop-up's Copy diagnostics text:
  https://www.theengineeringprojects.com/forum/category/motor-driver-proteus-library

SUPPORT US
This library is free. If it saves you time, please support our work:
  https://www.theengineeringprojects.com/donate

WEBSITE
  https://www.theengineeringprojects.com/

LICENCES AND THIRD-PARTY NOTES
* The model (TEPTRACKER.DLL), the symbols and artwork, the other parts of ours in the demo and the
  Arduino Library V4.0 (ArduinoV4TEP.LIB / TEPARDUINO.DLL, with its built-in TEP Serial Monitor
  Advance) are made by The Engineering Projects. The models use only standard Windows libraries; no
  Visual C++ redistributable is needed.
  The C++ source code is not included.
* Arduino UNO V4.0 (ArduinoV4TEP.LIB / TEPARDUINO.DLL, our Arduino Library V4.0 - its
  microcontroller is Proteus's own AVR model): The Engineering Projects,
  https://www.theengineeringprojects.com/2026/10/arduino-uno-library-for-proteus-v40.html
* The .hex file is built from the demo sketch and the Arduino AVR core 1.8.6, which includes
  LGPL-licensed code; its source code is available at
  https://github.com/arduino/ArduinoCore-avr/tree/1.8.6
* Proteus is a product of Labcenter Electronics and is not included. Arduino is a trademark of Arduino SA.
  This library is not made or endorsed by Arduino or Labcenter.

REBUILDING THE FIRMWARE (OPTIONAL)
The HEX file is supplied; Arduino IDE is not needed to run the demo. To edit the sketch, open
Arduino Code\SolarTracker_Demo\SolarTracker_Demo.ino, select Arduino Uno and use Sketch > Export
Compiled Binary. Replace the simulation's .hex with the exported HEX. The sketch needs 8,494 bytes
of flash and 328 bytes of RAM.

MODEL SCOPE AND LIMITS
Modelled: the sun's place from the solar time, the latitude and the day; the light of a clear sky
from the air mass and of
a cloudy sky; the two servos (544 - 2400 us, 600 degrees a second, their supply current); the four
LDRs (15 kohm at
10 lux, gamma 0.7, 30 ms) behind the shade cross and the grey cap; the panel's current against its
voltage and its
light; the light a fixed panel (south, tilted by the latitude) would catch. Our own figures: the
cross's height, the
cap's 1 %, the servos' currents, the panel's curve (a typical 6 V 1 W panel). Not modelled: the
panel's temperature,
wind, the servos' torque and gears, the clock's difference between solar time and the time on a
watch, places south of
the equator.

VERSION
TEP Dual-Axis Solar Tracker library V1.0 (Nov 2026). Device SOLARTRACKERTEP (TEPTRACKER.LIB /
TEPTRACKER.DLL). Demo sketch SolarTracker_Demo V1.0 (the Servo library of the Arduino IDE). Demo
board: ARDUINO UNO V4.0 (TEP Arduino Library V4.0) with its built-in serial monitor.
Advertisement

Development1 release

  1. V1.0Dual-Axis Solar Tracker Library for Proteus V1.0this page

    V1.0 is the only release in the Download Center so far. When a newer version is published, it appears above with its own download page.

Installation8 steps

From the download to a working project, in order. The steps follow what the package contains.

You will need

  • Proteus Design SuiteProteus 8 or newer (Labcenter), on Windows
  • Arduino IDE1.8 or 2.x, with the board of the tutorial chosen under Tools → Board
  • Any archive toolWindows, macOS and Linux extract ZIP files on their own

Steps

  1. 1

    Extract the archive

    Right-click f993d1cb82664907827183cb4377fa41.zip and choose Extract All (or open it with 7-Zip or WinRAR) into a folder you can find again. Keep its folder structure (Dual-Axis-Solar-Tracker-TEP-v1.0) as it is.

  2. 2

    Copy the library files into Proteus

    Move ArduinoV4TEP.LIB and TEPTRACKER.LIB and the files into the LIBRARY folder of your Proteus installation: C:\Program Files (x86)\Labcenter Electronics\Proteus 8 Professional\LIBRARY for Proteus 8, or the matching Proteus 7 folder. Older versions keep it under ProgramData\Labcenter Electronics. If Proteus is open, close it first.

  3. 3

    Add the simulation model

    Copy TEPARDUINO.DLL and TEPTRACKER.DLL into the MODELS folder next to LIBRARY, so the component can run, not only be drawn.

  4. 4

    Restart Proteus and place the component

    Start Proteus, open a schematic, press P (Pick Devices) and search for the component by the name used in the tutorial. It appears with its pins ready to wire.

  5. 5

    Open the sketch in the Arduino IDE

    Open SolarTracker_Demo.ino, select your board and port under Tools, then Verify. Sketch → Export Compiled Binary writes the HEX file a simulation needs.

  6. 6

    Load the HEX file

    In Proteus double-click the microcontroller, set Program File to SolarTracker_Demo.hex and run the simulation. For real hardware, flash the same file with your programmer.

  7. 7

    Open the example simulation

    Open Dual-Axis-Solar-Tracker-ArduinoUnoV4.pdsprj in Proteus to see the wiring exactly as in the tutorial. Check the controller's Program File path, then press Play.

  8. 8

    Follow the tutorial

    Dual-Axis Solar Tracker Library for Proteus Simulation explains every connection and setting in order; keep it open beside the files while you build.

How to add a library in Proteus 8

FAQs9 questionsContact TEP

How do I download Dual-Axis Solar Tracker Library for Proteus V1.0?

Wait for the 30-second guest countdown on this page, then press the download button; the file comes straight from our storage. Members who are logged in skip the wait. If the browser opens the file instead of saving it, use its Save as option. The download link is made for you when the countdown ends and works for 15 minutes; a saved or shared link stops working, so share this page instead.

What is inside the archive?

Dual-Axis Solar Tracker Library for Proteus V1.0 comes as a ZIP archive of 10 files (1.2 MB, 2.7 MB unpacked) holding Proteus library files, simulation model DLLs, a Proteus simulation, an Arduino sketch and compiled HEX firmware. Open the File Structure tab for the full list of 10 files.

What should I do if the download does not start?

Check the browser's download list first; an ad blocker or a company firewall can also hold it back, so try another browser or network. If the file arrives incomplete, download it again. For an installation problem, read the Install tab or tell us in the comments with your software version and the exact error message.

Is this file free?

Yes. Every file in the TEP Download Center is free for learning, personal and student projects. If you share it, link back to this page or the tutorial so others find the latest version.

How do I check that the file arrived complete?

Compare its SHA-256 with the one on this page, 3f79273b0d8ff5a3e1c35cdc28b410ed5a0f43e158a8ce866a7d04a0a86ef5c4. In PowerShell run Get-FileHash "f993d1cb82664907827183cb4377fa41.zip"; on macOS or Linux run shasum -a 256 "f993d1cb82664907827183cb4377fa41.zip". The same value means the file is exactly the one in our storage; a different one means the download broke off, so download it again.

Do I need WinRAR to open the ZIP file?

No. Windows, macOS and Linux open ZIP archives on their own (Extract All, or double-click). WinRAR and 7-Zip work too. Extract the whole archive before using the files.

Where do I put the LIB and IDX files?

Both files go into the LIBRARY folder of your Proteus installation (Proteus 8: C:\Program Files (x86)\Labcenter Electronics\Proteus 8 Professional\LIBRARY; Proteus 7 has the same folder under its own name). Restart Proteus afterwards and search for the component with P.

Which Proteus version does the library need?

The tutorial names the Proteus version the library was made and tested with. Most TEP libraries work in Proteus 7 and Proteus 8; if the component does not appear after a restart, check that both the LIB and the IDX file were copied and that Proteus was fully closed while copying.

How do I get the HEX file into the simulation?

Compile the sketch in the Arduino IDE (Sketch → Export Compiled Binary gives you the HEX next to the sketch), then in Proteus double-click the board, set Program File to that HEX and run.

preparing · f993d1cb82664907827183cb4377fa41.zip
Rating
Your download will be ready shortly
Preparing your download…

Members skip the wait. Log in or join TEP.

  • 0Total downloads
  • 4%Popularity
  • ProteusCategory
  • 0Comments
  • ssyedzainnasirUploaded by
  • 17 Nov 2026Uploaded at
Last 14 days0 downloads
SHA-256 3f79273b0d8ff5a3e1c35cdc28b410ed5a0f43e158a8ce866a7d04a0a86ef5c4
DocumentationDual-Axis Solar Tracker Library for Proteus Simulation
Need help with this file? Bug report Ask a question Download problemsGet updates
Advertisement

Comments

0

Join the conversation

Start the conversationAsk a question or share how you used this download.