Project Files of nRF52840 DK Library for Proteus: Bluetooth LE Simulation
0ebd2682570e419b85259678f4dc7c81.zip

nRF52840 DK Library for Proteus V1.0
nRF52840 DK Library for Proteus V1.0 comes as a ZIP archive of 285 files (3.5 MB, 7.9 MB unpacked) holding Proteus library files, simulation model DLLs, a Proteus simulation, an Arduino sketch, an Arduino library, compiled HEX firmware and source code.
- LIBProteus library
- DLLProteus model
- DSNProteus simulation
- INOArduino sketch
- LIBArduino library
- HEXHEX firmware
- SRCSource code
Description
nRF52840-DK-Library-for-Proteus-v1.0.zip with the nRF52840 DK in Proteus (your sketch with the DK's pin names, four LEDs, four buttons, Bluetooth LE to a phone and a serial monitor; TEPNRF52840DK.LIB, TEPNET.DLL and the TEP Boards for Proteus add-on 1.59.0), the BME280 and phone libraries, the weather node demo with its sketch and a README.
File Structure
6.2 KB1.1 KB7.7 KB11 KB8.5 KB1.5 KB1.7 KB1.9 KB5.7 KB4.9 KB1.1 KB5.8 KB9.6 KB7.2 KB2.5 KB2.1 KB1.9 KB2.1 KB4.4 KB1.1 KB3 KB3 KB1.8 KB2.5 KB3.5 KB149 B2.7 KB2 KB6.4 KB3.2 KB1.3 KB963 B8.6 KB5.9 KB6 KB12 KB1.6 KB1.3 KB14.7 KB4.3 KB6.1 KB20.1 KB8.2 KB2 KB4.5 KB311 B12.8 KB6.7 KB6.1 KB2.2 KB3.4 KB5.9 KB1.5 KB1.6 KB16.6 KB9.7 KB6.9 KB2.1 KB533 B5.7 KB7.4 KB514 B1.7 KB896 B481 B1.4 KB1012 B482 B936 B559 B467 B3.6 KB3.8 KB504 B956 B575 B455 B8.3 KB10.9 KB522 B79 B5.5 KB3.1 KB79 B442 B918 B1.4 KB1.8 KB1 KB1.3 KB1.4 KB1.8 KB1.4 KB5.7 KB502 B463 B5 KB6.5 KB3.4 KB3.4 KB500 B1.6 KB368 B406 B466 B404 B444 B460 B477 B739 B448 B1.3 KB350 B5.7 KB4 KB562 B1.5 KB2 KB550 B7.2 KB4.1 KB371 B4.5 KB3.5 KB492 B390 B478 B6.6 KB2.4 KB479 B5.1 KB1.9 KB1.3 KB1.3 KB750 B1.3 KB490 B2.2 KB1.9 KB498 B1.2 KB1.2 KB487 B5.1 KB4.6 KB371 B1.5 KB1.2 KB478 B6.2 KB3 KB1.5 KB1.7 KB469 B1 KB1.7 KB433 B294 B358 B1.3 KB2.5 KB13.2 KB3.8 KB659 B510 B4.4 KB1.9 KB5.8 KB11 KB835 B518 B6.4 KB2.3 KB29 B436 B9.2 KB4.9 KB439 B4.2 KB1.5 KB9.3 KB7.1 KB4.7 KB2.4 KB388 B5.1 KB893 B667 B1.3 KB5.5 KB2.3 KB1.8 KB468 B882 B530 B791 B487 B894 B2 KB730 B646 B2.6 KB977 B702 B20.6 KB1.8 KB11.8 KB3.2 KB596 B406 B6.3 KB5.7 KB9.3 KB7.7 KB7.7 KB5.8 KB5.9 KB6.4 KB6.4 KB5.3 KB5.6 KB5.7 KB7.9 KB7.7 KB6.5 KB6.3 KB6.2 KB10.3 KB8.5 KB6.6 KB7.6 KB6.7 KB6.1 KB6.7 KB8.3 KB6.2 KB7.2 KB5.9 KB5.6 KB5.7 KB6.7 KB5.9 KB6.2 KB6 KB6 KB6.1 KB6.3 KB6 KB6.1 KB6.2 KB6 KB5.8 KB6.4 KB7 KB6.5 KB6.6 KB6.5 KB5.6 KB7.5 KB7.7 KB7.1 KB5.8 KB5.9 KB5.9 KB6.9 KB5.5 KB5.5 KB7.1 KB5.2 KB29 KB25.9 KB1.3 KB8.5 KB34.4 KB89.4 KB39.5 KB13.1 KB39 KB381 KB2.9 MB60 KB21.8 KB381 KB2.9 MB12 KBGallery12 images from the tutorialOpen the tutorial
The circuit, the board and the results as they appear in nRF52840 DK Library for Proteus: Bluetooth LE Simulation. Open an image for its full size.












README
NRF52840 DK LIBRARY FOR PROTEUS - V1.0 (YOUR ARDUINO SKETCH, BLUETOOTH LE TO A PHONE, FOUR LEDS AND FOUR BUTTONS)
Designed by The Engineering Projects
www.TheEngineeringProjects.com
IMPORTANT LINKS
Article (read it first - pictures, step by step, every feature explained):
https://www.theengineeringprojects.com/2026/11/nrf52840-dk-library-for-proteus.html
Report a bug or suggest a feature (our forum):
https://www.theengineeringprojects.com/forum
The demo's other parts are our libraries (included) - their articles:
https://www.theengineeringprojects.com/2026/09/bme280-sensor-library-for-proteus.html
https://www.theengineeringprojects.com/2026/10/mobile-wifi-monitor-library-for-proteus.html
Support us (the libraries are free):
https://www.theengineeringprojects.com/donate
FILE STRUCTURE
nRF52840-DK-TEP-v1.0/
|-- Proteus Library Files/
| |-- TEPBME280.LIB 89.4 KB the BME280 (demo), to LIBRARY
| |-- TEPLAPTOP.LIB 39.5 KB the laptop (demo), to LIBRARY
| |-- TEPMOBILE.LIB 13.1 KB the phone (demo), to LIBRARY
| |-- TEPNRF52840DK.LIB 39.0 KB the nRF52840 DK, to LIBRARY
|-- Proteus Model Files/
| |-- TEPBME280.DLL 381.0 KB the BME280, to MODELS
| |-- TEPNET.DLL 2.90 MB the board + monitors + network, to MODELS
|-- Arduino Code/
| |-- DK_BLE_Weather_Node/DK_BLE_Weather_Node.ino 6.2 KB the demo sketch
| |-- TEP Boards for Proteus/hardware/ 1.11 MB the Arduino IDE add-on 1.59.0 (273 files)
|-- Proteus Simulation/
| |-- DK_BLE_Weather_Node.hex 60.0 KB the demo sketch (U1)
| |-- nRF52840-DK-BLE-Weather-Node.pdsprj 21.8 KB the demo: a Bluetooth LE weather node
| |-- TEPBME280.DLL 381.0 KB copy of the model
| |-- TEPNET.DLL 2.90 MB copy of the model
|-- README.txt ~11.5 KB this file
Total: 7.92 MB (unzipped). The source code of the models is not included.
WHAT IS IT?
Proteus 8 has no nRF52840 processor model, so this is NOT a real nRF52840 chip. Our team has put a lot of effort into
building this board ourselves: it is Nordic Semiconductor's nRF52840 DK (PCA10056) - the blue development kit with the
nRF52840 SoC, its PCB antenna, the interface MCU with its USB port, the power switch, four green LEDs and four buttons -
drawn compact, and it runs YOUR Arduino sketch in Proteus:
* You write a normal sketch for the DK's Arduino header (D0 .. D13, A0 .. A5, SDA, SCL; analogRead 0-1023,
analogWrite, attachInterrupt, tone, Wire, SPI, Serial, Serial1) and compile it in the Arduino IDE with our board
package "TEP Boards for Proteus" 1.59.0 (in Arduino Code - see INSTALLATION).
* LED1 .. LED4 light when LOW, as on the real DK (LED_BUILTIN is LED1). BUTTON1 .. BUTTON4 read LOW while you hold
them: click a button on the board in the running simulation.
* Bluetooth LE works through ArduinoBLE: the board advertises as a peripheral with your services and
characteristics, and our Mobile WiFi Monitor's Bluetooth app is the central (it lists the board, connects, reads,
writes and gets the notifications).
TEP additions: the USB port opens the serial monitor (the same window as our TEP Serial Monitor Advance).
Limits (say them before you start): one phone is the central; the board cannot be a central itself. Thread, Zigbee,
802.15.4, NFC, USB device classes and the QSPI flash are drawn, not modelled.
Your sketch gets 8 KB of RAM in the simulation (the real one: 256 KB), about 256 KB of flash, and int is 16 bits in
the simulation (use long for big numbers). See MODEL SCOPE AND LIMITS.
ONE DEVICE (search "NRF52840" in Pick Devices):
NRF52840 DK "nRF52840 DK" V1.0 (Microprocessor ICs > Bluetooth Boards), prefix U, model TEPNET.DLL.
Its TEP window has no Windows title bar: the serial monitor (the USB port, 115200 baud: Monitor, Plotter and Board
tabs).
The same TEPNET.DLL also runs our other sketch boards and the phone; it replaces any older TEPNET.DLL (keep only this
newest one in MODELS).
TEST STATUS
V1.0: verified in Proteus 8.5 on 17 Nov 2026 with the demo project as shipped. What the Proteus run showed:
* nRF52840-DK-BLE-Weather-Node: the banner, "Advertising as "nRF52840 DK Weather"" with the board's address, the
button help line and "First reading: 24.0 C 50 % 1013.0 hPa"; LED1 blinked while the node advertised.
* The phone's Bluetooth app listed nRF52840 DK Weather; Connect: ">> Phone connected", LED1 stayed on, and the phone
showed Temperature C 24.00, Humidity % 50.00, Pressure hPa 1013.00, Alarm above C 28.00 and Last button 0.
* BUTTON1: "reading on request" at once. BUTTON3 twice: "alarm above 28.5 C", then 29.0 C, on the phone too. BUTTON4:
"night mode ON (LED4 quiet)" and LED3 on; LED4 no longer flashed at each reading. The phone's Last button: 4.
* The BME280's pop-up, a warmer room: "Room: 32.5 C", ">> ALARM: warmer than 29.0 C" and LED2 on; the phone followed.
* BUTTON2: "alarm above 28.5 C" (LED2 stayed on); BUTTON4 again: "night mode OFF".
* about 27 s of simulation, no errors, with the BME280's window, the phone and the monitor open.
INSTALLATION (about 3 minutes)
1. Close Proteus. Extract the WHOLE ZIP to a normal folder (e.g. Desktop).
2. Copy everything in "Proteus Library Files" to the LIBRARY folder of Proteus, for example:
C:\Program Files (x86)\Labcenter Electronics\Proteus 8 Professional\LIBRARY
(on some PCs: C:\ProgramData\Labcenter Electronics\Proteus 8 Professional\LIBRARY). TEPNRF52840DK.LIB is the board;
the others are the demo's parts: TEPBME280.LIB, TEPMOBILE.LIB and TEPLAPTOP.LIB.
3. Copy the DLLs from "Proteus Model Files" (TEPNET.DLL, TEPBME280.DLL) to the MODELS folder
(...\Proteus 8 Professional\MODELS) -
replace an older TEPNET.DLL (this one is the first that knows this board).
4. Delete TEPNRF52840DK.IDX from the LIBRARY folder if it is there.
5. The Arduino IDE (only to compile your own sketches - the demo has its HEX file): copy the folder
"Arduino Code\TEP Boards for Proteus\hardware" into your sketchbook folder (normally Documents\Arduino), so that
Documents\Arduino\hardware\tep\avr\boards.txt exists (replace an older copy); restart the IDE. The Arduino AVR Boards
platform must be installed (it comes with IDE 1.8.x; in IDE 2.x install "Arduino AVR Boards" from the Boards
Manager once).
Tools > Board > TEP Boards for Proteus > Nordic nRF52840 DK (TEP Proteus). ArduinoBLE is in the board package.
From the Library Manager: Adafruit BME280 and Adafruit Unified Sensor.
6. Start Proteus. In Pick Devices (P) search "NRF52840".
RUN THE DEMO
Keep the .hex file and the DLLs beside the project in "Proteus Simulation".
nRF52840-DK-BLE-Weather-Node.pdsprj - U1 the nRF52840 DK (DK_BLE_Weather_Node.hex) is a Bluetooth LE weather node:
U2 = the BME280 (Advance) on the I2C header (SDA, SCL), MOB1 = the phone (Mobile WiFi Monitor), the central.
Press Run. The monitor prints "Advertising as "nRF52840 DK Weather"" and LED1 blinks. On the phone open the Bluetooth
app and click Connect: LED1 stays on and the phone shows the temperature, the humidity, the pressure, the alarm limit
and the last button.
Click the buttons on the board: BUTTON1 sends a reading at once, BUTTON2 / BUTTON3 move the alarm 0.5 C down / up,
BUTTON4 switches night mode (LED3 on, LED4 quiet). On the BME280's pop-up click the Temperature track above 28 C:
the monitor prints the ALARM and LED2 lights. Click the phone's Alarm above C row, type a number and press Send to
set the limit from the phone.
Closed a window? The USB port opens the monitor, the OPEN PANEL pad opens the BME280, a click on the phone's screen
the phone.
THE PINS (the label on the part, what it can do in the simulation)
D0, D1 Serial1 RX and TX, or GPIO (the real DK: P1.01, P1.02)
D2 .. D13 GPIO, PWM (analogWrite), interrupt; D10 .. D13 SPI (SS, MOSI, MISO, SCK)
A0 .. A5 analogRead 0 .. 1023 for 0 .. 3.3 V, or GPIO (the core's numbers 14 .. 19)
SDA, SCL Wire (the real DK: P0.26, P0.27)
VDD, 5V, GND 3.3 V (the logic), 5 V, ground; RESET the board's reset (the RESET button too)
AREF, VIN drawn, not modelled
LED1 .. LED4 (22 .. 25) are the green LEDs, lit when LOW; LED_BUILTIN is LED1, with LED_BUILTIN_ACTIVE and
LED_BUILTIN_INACTIVE. BUTTON1 .. BUTTON4 (26 .. 29) are the buttons, LOW when pressed (pinMode INPUT_PULLUP);
BTN_BUILTIN is BUTTON1. Serial is the USB: the board's built-in monitor. The pin header follows the real DK's
Arduino Uno layout; pins_arduino.h lists the real P0 / P1 GPIO of each pin.
PROPERTIES (double-click the part > Edit Properties)
PROGRAM the sketch's HEX (Arduino IDE: Sketch > Export Compiled Binary with Nordic nRF52840 DK (TEP Proteus))
MONITOR YES = the built-in serial monitor on Serial; BAUD its speed (115200, or AUTO)
AUTOOPEN YES = the monitor window opens at Run (the demo: YES)
TROUBLESHOOTING
* The phone's list is empty: call BLE.begin(), set a local name and BLE.advertise(); call BLE.poll() in loop(). The
phone needs this TEPNET.DLL or newer.
* "BME280 not found": the demo's sensor is at 0x76 (SDO to GND). Check SDA and SCL.
* A button does nothing: use pinMode(BUTTONx, INPUT_PULLUP) and act when digitalRead() is LOW.
* The LEDs look inverted: they light when the pin is LOW, as on the real DK.
* An integer goes wrong above 32767: int is 16 bits in the simulation - use long.
BUG REPORTS AND FEATURE REQUESTS
Please post them in our forum with a screenshot and the Serial Monitor text:
https://www.theengineeringprojects.com/forum
LICENCES AND THIRD-PARTY NOTES
* The board model (TEPNET.DLL), the symbols and artwork (TEPNRF52840DK.LIB) and the BME280 model are made by The
Engineering Projects. The source code of the models is not included.
* TEP Boards for Proteus (Arduino Code): its core, the variants and the EEPROM, SPI and Wire libraries are modified
copies of the Arduino AVR core 1.8.6 - GNU Lesser General Public License 2.1 (LGPL 2.1, the text:
LICENSE-LGPL-2.1.txt); its WiFi, WebServer, ArduinoBLE, the sensor libraries and the others and our core files are
MIT (LICENSE-MIT.txt).
* Our ArduinoBLE has the calls of the library of that name; its code is ours.
* The demo sketch uses Adafruit BME280 and Adafruit Unified Sensor (BSD, Apache 2.0): install them with the Library
Manager to rebuild.
* Proteus is a product of Labcenter Electronics and is not included. nRF52840 and Nordic Semiconductor are names of
Nordic Semiconductor ASA, Arduino of Arduino. The Bluetooth word mark belongs to Bluetooth SIG. This library is not
made or endorsed by them or by Labcenter.
REBUILDING THE FIRMWARE (OPTIONAL)
The HEX file is supplied. Install TEP Boards for Proteus (INSTALLATION step 5), open Arduino
Code\DK_BLE_Weather_Node, select Nordic nRF52840 DK (TEP Proteus) and use Sketch > Export Compiled Binary. For a real
board use Nordic's nRF Connect SDK, or an Arduino core for nRF52 boards with a matching ArduinoBLE. Its pins work
at 3.3 V.
MODEL SCOPE AND LIMITS
Modelled: the DK's Arduino header; digital I/O, analogRead 0 .. 1023, PWM (analogWrite), tone and attachInterrupt
through the board model; Serial (the board's monitor), Serial1, Wire and SPI; the four LEDs, the four buttons and
RESET; Bluetooth LE as a peripheral (ArduinoBLE) with the phone as the central.
Not modelled: the nRF52840 itself, the radio's range, Thread, Zigbee, 802.15.4, NFC, USB device classes, the QSPI
flash, the current measurement header, the board as a central. The simulation runs below real time.
VERSION
TEP nRF52840 DK library V1.0 (Nov 2026). Device NRF52840 DK (TEPNRF52840DK.LIB / TEPNET.DLL), TEP Boards for Proteus
1.59.0 (adds this board: LED1 .. LED4, BUTTON1 .. BUTTON4).
Demo sketch DK_BLE_Weather_Node V1.0. Demo parts: BME280ADVTEP and MOBILE WIFI MONITOR.Development1 release
-
V1.0nRF52840 DK Library for Proteus V1.0this page
V1.0 is the only release in the Download Center so far. When a newer version is published, it appears above with its own download page.
Installation10 steps
From the download to a working project, in order. The steps follow what the package contains.
You will need
- Proteus Design SuiteProteus 8 or newer (Labcenter), on Windows
- Arduino IDE1.8 or 2.x, with the board of the tutorial chosen under Tools → Board
- The compiler named in the tutorialto build the source files into firmware
- Any archive toolWindows, macOS and Linux extract ZIP files on their own
Steps
- 1
Extract the archive
Right-click 0ebd2682570e419b85259678f4dc7c81.zip and choose Extract All (or open it with 7-Zip or WinRAR) into a folder you can find again. Keep its folder structure (nRF52840-DK-TEP-v1.0) as it is.
- 2
Copy the library files into Proteus
Move TEPBME280.LIB, TEPLAPTOP.LIB and TEPMOBILE.LIB and 1 more and the files into the LIBRARY folder of your Proteus installation: C:\Program Files (x86)\Labcenter Electronics\Proteus 8 Professional\LIBRARY for Proteus 8, or the matching Proteus 7 folder. Older versions keep it under ProgramData\Labcenter Electronics. If Proteus is open, close it first.
- 3
Add the simulation model
Copy TEPBME280.DLL and TEPNET.DLL into the MODELS folder next to LIBRARY, so the component can run, not only be drawn.
- 4
Restart Proteus and place the component
Start Proteus, open a schematic, press P (Pick Devices) and search for the component by the name used in the tutorial. It appears with its pins ready to wire.
- 5
Install the Arduino library
In the Arduino IDE choose Sketch → Include Library → Add .ZIP Library and pick the library, or copy its folder into Documents\Arduino\libraries. Restart the IDE to see its examples.
- 6
Open the sketch in the Arduino IDE
Open DK_BLE_Weather_Node.ino, eeprom_clear.ino and eeprom_crc.ino and 17 more, select your board and port under Tools, then Verify. Sketch → Export Compiled Binary writes the HEX file a simulation needs.
- 7
Build the source code
Open abi.cpp, Arduino.h and binary.h and 52 more in the compiler named in the tutorial (MikroC, Keil, MPLAB, Code Composer or the Arduino IDE) and build it to get the firmware.
- 8
Load the HEX file
In Proteus double-click the microcontroller, set Program File to DK_BLE_Weather_Node.hex and run the simulation. For real hardware, flash the same file with your programmer.
- 9
Open the example simulation
Open nRF52840-DK-BLE-Weather-Node.pdsprj in Proteus to see the wiring exactly as in the tutorial. Check the controller's Program File path, then press Play.
- 10
Follow the tutorial
nRF52840 DK Library for Proteus: Bluetooth LE Simulation explains every connection and setting in order; keep it open beside the files while you build.
FAQs9 questionsContact TEP
How do I download nRF52840 DK Library for Proteus V1.0?
Wait for the 30-second guest countdown on this page, then press the download button; the file comes straight from our storage. Members who are logged in skip the wait. If the browser opens the file instead of saving it, use its Save as option. The download link is made for you when the countdown ends and works for 15 minutes; a saved or shared link stops working, so share this page instead.
What is inside the archive?
nRF52840 DK Library for Proteus V1.0 comes as a ZIP archive of 285 files (3.5 MB, 7.9 MB unpacked) holding Proteus library files, simulation model DLLs, a Proteus simulation, an Arduino sketch, an Arduino library, compiled HEX firmware and source code. Open the File Structure tab for the full list of 285 files.
What should I do if the download does not start?
Check the browser's download list first; an ad blocker or a company firewall can also hold it back, so try another browser or network. If the file arrives incomplete, download it again. For an installation problem, read the Install tab or tell us in the comments with your software version and the exact error message.
Is this file free?
Yes. Every file in the TEP Download Center is free for learning, personal and student projects. If you share it, link back to this page or the tutorial so others find the latest version.
How do I check that the file arrived complete?
Compare its SHA-256 with the one on this page, 6f9dbba14e44fbce5312e68ca6b3713fc3d984139b02398753293439582dc814. In PowerShell run Get-FileHash "0ebd2682570e419b85259678f4dc7c81.zip"; on macOS or Linux run shasum -a 256 "0ebd2682570e419b85259678f4dc7c81.zip". The same value means the file is exactly the one in our storage; a different one means the download broke off, so download it again.
Do I need WinRAR to open the ZIP file?
No. Windows, macOS and Linux open ZIP archives on their own (Extract All, or double-click). WinRAR and 7-Zip work too. Extract the whole archive before using the files.
Where do I put the LIB and IDX files?
Both files go into the LIBRARY folder of your Proteus installation (Proteus 8: C:\Program Files (x86)\Labcenter Electronics\Proteus 8 Professional\LIBRARY; Proteus 7 has the same folder under its own name). Restart Proteus afterwards and search for the component with P.
Which Proteus version does the library need?
The tutorial names the Proteus version the library was made and tested with. Most TEP libraries work in Proteus 7 and Proteus 8; if the component does not appear after a restart, check that both the LIB and the IDX file were copied and that Proteus was fully closed while copying.
How do I get the HEX file into the simulation?
Compile the sketch in the Arduino IDE (Sketch → Export Compiled Binary gives you the HEX next to the sketch), then in Proteus double-click the board, set Program File to that HEX and run.
Members skip the wait. Log in or join TEP.
- 0Total downloads
- 4%Popularity
- ProteusCategory
- 0Comments
- ssyedzainnasirUploaded by
- 18 Nov 2026Uploaded at
6f9dbba14e44fbce5312e68ca6b3713fc3d984139b02398753293439582dc814





















Comments
0