TEP DOWNLOAD CENTER

Project Files of MT3608 DC-DC Boost Converter Module Library for Proteus Simulation

Libraries Code Projects Simulation
tep://download-terminal 8bacb42e7c4440e1b82baa83265aea8d.zip ZIP archiveV1.0Verified0 downloadsFree
MT3608 DC-DC Boost Converter Module Library for Proteus Simulation: the module makes 12 V from one 18650 cell beside an Arduino UNO V4.0
Proteus library · File 1 of 1

MT3608 DC-DC Boost Converter Module Library for Proteus V1.0

MT3608 DC-DC Boost Converter Module Library for Proteus V1.0 comes as a ZIP archive of 13 files (1.5 MB, 3.2 MB unpacked) holding Proteus library files, simulation model DLLs, a Proteus simulation, an Arduino sketch and compiled HEX firmware.

  • LIBProteus library
  • DLLProteus model
  • DSNProteus simulation
  • INOArduino sketch
  • HEXHEX firmware

Description

MT3608-DC-DC-Boost-Converter-Module-Library-for-Proteus-v1.0.zip with the MT3608 boost module for Proteus simulation (TEPMT3608.LIB and TEPMT3608.DLL), our 18650 cell and Arduino UNO V4.0, the A4 demo with its sketch and a README.

Read MT3608 DC-DC Boost Converter Module Library for Proteus Simulation

File Structure

8bacb42e7c4440e1b82baa83265aea8d.zip13 files · 5 folders · 3.2 MB unpacked
MT3608-Boost-Converter-TEP-v1.0/13 files · 3.2 MB
Arduino Code/1 file · 2.7 KB
Boost_Demo/1 file · 2.7 KB
INO Boost_Demo.inoArduino sketch 2.7 KB
Proteus Library Files/3 files · 234.5 KB
LIB ArduinoV4TEP.LIBProteus library 201.9 KB
LIB TEP18650.LIBProteus library 11.9 KB
LIB TEPMT3608.LIBProteus library 20.7 KB
Proteus Model Files/3 files · 1.5 MB
DLL TEP18650.DLLSimulation model 319.5 KB
DLL TEPARDUINO.DLLSimulation model 883.5 KB
DLL TEPMT3608.DLLSimulation model 314 KB
Proteus Simulation/5 files · 1.5 MB
HEX Boost_Demo.hexCompiled HEX file 15.6 KB
DSN MT3608-Boost-Converter-18650-ArduinoUnoV4.pdsprjProteus simulation 20.4 KB
DLL TEP18650.DLLSimulation model 319.5 KB
DLL TEPARDUINO.DLLSimulation model 883.5 KB
DLL TEPMT3608.DLLSimulation model 314 KB
TXT README.txtText file 16.6 KB

README

README.txt 293 lines
MT3608 DC-DC BOOST CONVERTER MODULE LIBRARY FOR PROTEUS SIMULATION - V1.0 (a step-up module with a pop-up)
Designed by The Engineering Projects
www.TheEngineeringProjects.com

IMPORTANT LINKS
Article (read it first - pictures, step by step, every feature explained):
  https://www.theengineeringprojects.com/2026/11/mt3608-dc-dc-boost-converter-module-library-for-proteus.html
Report a bug or suggest a feature (our forum):
  https://www.theengineeringprojects.com/forum/category/motor-driver-proteus-library
The demo runs on our Arduino UNO V4.0 (included) - working LEDs, RESET and a
built-in serial monitor, no Virtual Terminal to wire - its own article:
  https://www.theengineeringprojects.com/2026/10/arduino-uno-library-for-proteus-v40.html
The demo's cell is our 18650 Li-ion Battery library (its LIB and DLL are in this zip; its own article):
  https://www.theengineeringprojects.com/2026/11/18650-li-ion-battery-library-for-proteus.html
Support us (the libraries are free):
  https://www.theengineeringprojects.com/donate

FILE STRUCTURE
MT3608-Boost-Converter-TEP-v1.0/
|-- Proteus Library Files/
|   |-- ArduinoV4TEP.LIB                              201.9 KB   TEP Arduino boards V4.0 (UNO) -> LIBRARY
|   |-- TEP18650.LIB                                   11.9 KB   a part the demo uses -> LIBRARY folder
|   |-- TEPMT3608.LIB                                  20.7 KB   the library -> LIBRARY folder
|-- Proteus Model Files/
|   |-- TEP18650.DLL                                  319.5 KB   its model -> MODELS folder
|   |-- TEPARDUINO.DLL                                883.5 KB   the Arduino board model -> MODELS folder
|   |-- TEPMT3608.DLL                                 314.0 KB   the model -> MODELS folder
|-- Proteus Simulation/
|   |-- Boost_Demo.hex                                 15.6 KB   the demo firmware
|   |-- MT3608-Boost-Converter-18650-ArduinoUnoV4.pdsprj   20.4 KB   the demo project
|   |-- TEP18650.DLL                                  319.5 KB   copy of its model
|   |-- TEPARDUINO.DLL                                883.5 KB   copy of the board model
|   |-- TEPMT3608.DLL                                 314.0 KB   copy of the model
|-- Arduino Code/
|   |-- Boost_Demo/Boost_Demo.ino                       2.7 KB   the demo sketch (source of the .hex)
|-- README.txt                                        ~17.7 KB   this file
Total: 3.25 MB (unzipped). The C++ source code of the models is not included.

WHAT IS IT?
The small blue step-up (boost) module with the MT3608 chip, seen from above at its true size against
our Arduino UNO
(36 x 17 mm; our own drawing, no maker's mark): four pads, the blue multi-turn trimmer, the
inductor, the diode, the
chip. It makes a higher voltage from a lower one - 5 V, 9 V or 12 V from one Li-ion cell, for
example. Figures of the
chip's data sheet and of the module:
  * Input 2 to 24 V (the chip starts at 2 V); output up to 28 V; 1.2 MHz; an internal switch of 80
    milliohm with a
    current limit of 4 A; a reference of 0.6 V.
  * The module: a 22 uH inductor, an SS34 diode, a 100 k trimmer over 2.2 k: Vout = 0.6 V x (1 + R /
    2.2 k). VOUT is the
    voltage the trimmer is set to.
  * The model is a mean-value one (it does not switch at 1.2 MHz in the simulation): it holds the
    set voltage and takes
    the input current that the load and its own losses ask for - in the inductor, the switch, the
    diode, and in
    switching - so the efficiency comes out of the model.
  * The limits: past 4 A in the switch the output voltage sinks (CURRENT LIMIT); the chip heats up
    with its losses and
    switches off at 155 C (TOO HOT, ours: 150 C/W on the module); under 2 V it stops, and tries
    again after a
    quarter of a second (ours; a real chip tries again faster).
  * A boost converter can never give less than its input: with the chip off, or the trimmer set
    below the input, the
    input passes through the inductor and the diode (0.35 V less).
  * On the board a lamp shows the state and a line the output's volts and amps (ours). Click it at
    Run for the pop-up:
    where the power goes, with the four losses; the inductor's current over two switching periods
    with the duty;
    eight live values; graphs, an event log and a check page.
The body is drawn as on the real part and to true scale against our Arduino.
The TEP signature and the pop-up are TEP additions.

ONE DEVICE (search "MT3608" or "BOOST" in Pick Devices):
  MT3608BOOSTTEP  "MT3608 DC-DC Boost Converter Module V1.0" in TEPMT3608.LIB (Analog ICs >
  Regulators), prefix PS, model
                  TEPMT3608.DLL. Four pins: IN+ and IN- on the left, OUT+ and OUT- on the right; IN-
                  and OUT- are one
                  ground.

THE POP-UP
Click the part at Run. Tabs:
    Converter  chips: the trimmer set to 5, 9, 12 or 24 V. Where the power goes: the input, the
    converter and the output
               with their volts, amps and watts, and the four losses as bars; the inductor's current
               over two switching
               periods, with the part of each period in which the switch is closed; eight live
               values: the input, the
               output, the power in and out, the efficiency, the duty and the switch's peak current,
               the trimmer, the
               chip's temperature, the mode.
    Graphs     the live values over the last 2, 6 or 15 s. Live / Freeze.
    Event log  every change and warning; filters All / Changes / Warnings, Pause, Clear
    Check      what the part is doing and what to look at, each with a verdict (green = fine, amber
    = check, red = wrong)
    Settings   theme, text size, open at Run, window size
    Help       report a bug, suggest a feature, article, updates, donate, forum; Copy diagnostics
    for a bug report

TEST STATUS
V1.0: verified in Proteus 8.5 on 16 Nov 2026 (the demo project as shipped: an A4 sheet, an Arduino UNO V4.0).
What the runs showed (the model's own numbers and the sketch's monitor):
The demo as shipped (Boost_Demo; PS1 VOUT 12 on our 18650 cell BAT1 - SOC 90, SPEED 600: ten minutes
each simulated
second -, a 30 ohm load, a quarter of the output on A1), one run (bstfinal), the model's pauses:
  * 0.5 s, a nearly full cell: 3.91 V at 1.37 A in (5.36 W), 11.99 V at 0.40 A out (4.80 W): 89.6 %
    efficient; the
    switch closed 68 % of each period, 1.42 A peak (ripple 101 mA); the chip at 35 C. The losses:
    112 mW in the
    inductor, 102 mW in the switch, 140 mW in the diode, 205 mW in switching.
  * 3 s: 3.75 V at 1.44 A in (5.39 W), 89.0 %, the chip at 62 C; the cell's own pop-up: 63 % left
    (1642 mAh), 1 h 08
    min to empty at this current. On the sheet the module's lamp is green and the board shows 11.99
    V 0.40 A.
  * 8.5 s: 3.43 V at 1.60 A in (5.47 W), 87.6 %, the chip at 78 C; the monitor says LOW BATTERY
    (under 3.5 V).
  * 9.1 s, the cell nearly empty: 2.75 V at 2.10 A in (5.78 W), 82.9 %; duty 78 %, 2.14 A peak; the
    chip at 81 C with
    0.58 W in it.
  * The Event log: the same 4.80 W cost 1.44 A at 3.75 V, 1.56 A at 3.50 V, 1.70 A at 3.25 V, 1.88 A
    at 3.00 V, 2.41 A
    at 2.50 V and 3.52 A at 1.99 V (68 %); at 9.226 s UNDER 2 V - the chip stops; it tries again at
    9.477 s (the cell
    back at 3.13 V without the load) and is under 2 V again at 9.533 s.
  * 10 s: OFF, "the input falls under 2 V when the chip starts (3 tries)": 2.82 V in, 2.45 V at 0.08
    A pass through to
    the load. The cell's pop-up: 0 % left, 2347 mAh given, 52 mAh of them under 2.5 V (harm): the
    module does not
    protect the cell.
  * The Check page: the output between 1.54 and 11.99 V, the most input current 3.90 A, the chip
    never over 85 C.
  * The monitor (a line every 250 ms): ok down to 3.50 V, LOW BATTERY from 3.48 V to 2.82 V (five
    lines, the output
    still 12.00 V 0.40 A 4.80 W), then OUTPUT LOW (2.66 V, 0.09 A). 142 s for the 10 s.
A second run with a load of 8 ohm (bstlim2: R1 8R, SPEED 1), CURRENT LIMIT: at 1 s 3.86 V at 3.95 A
in (15.25 W), the
switch at its 4.00 A peak; the output sinks to 10.04 V at 1.26 A (12.60 W), 82.6 %; the chip at 100
C with 1.27 W in
it. At 2.294 s TOO HOT: the chip at 155 C switches off and 3.63 V at 0.45 A pass through; at 2.628 s
it is down to 135
C and starts again.
A third run with the trimmer at 3 V (bstpas2: VOUT 3, SPEED 1), PASSING THE INPUT: 4.09 V at 0.13 A
in, 3.72 V at 0.12
A out through the inductor and the diode; the switch rests.

INSTALLATION (about 2 minutes)
1. Close Proteus. Extract the WHOLE ZIP to a normal folder (e.g. Desktop).
2. Copy everything in "Proteus Library Files" (TEPMT3608.LIB, TEP18650.LIB and our Arduino library
V4.0, ArduinoV4TEP.LIB, with the ARDUINO UNO V4.0 used by the demo) to the LIBRARY folder of
Proteus, for example:
     C:\Program Files (x86)\Labcenter Electronics\Proteus 8 Professional\LIBRARY
   (use the folder that already holds Proteus's own .LIB files).
3. Copy TEPMT3608.DLL, TEP18650.DLL and TEPARDUINO.DLL from "Proteus Model Files" to the MODELS
folder (...\Proteus 8 Professional\MODELS).
4. Delete TEPMT3608.IDX from the LIBRARY folder if it is there (Proteus makes a new index).
5. Start Proteus. In Pick Devices (P) search "MT3608".

RUN THE DEMO
"Proteus Simulation\MT3608-Boost-Converter-18650-ArduinoUnoV4.pdsprj" (an A4 sheet) - keep the .hex
file and the DLLs beside the project.
  12 V from one Li-ion cell, with a monitor:
  ARD1:   Arduino UNO V4.0 running Boost_Demo.hex, its serial monitor built in (window "TEP Arduino
  UNO - ARD1").
  PS1:    the module, VOUT 12: IN+ on the cell's + (the label VIN), IN- and OUT- on ground, OUT+ on
  the label VOUT.
  BAT1:   our 18650 Li-ion cell, 2600 mAh, SOC 90 %, SPEED 600 (ten minutes each simulated second),
  - on ground.
  R1:     30 ohm, the load, from VOUT to ground: 0.4 A and 4.8 W at 12 V.
  R2, R3: 30k and 10k: a quarter of VOUT to A1. The cell's voltage goes straight to A0.
          Four times a second the sketch prints the input voltage, the output voltage, the load's
          current and power,
          and warns with LOW BATTERY and the UNO's LED when the cell is down to 3.5 V.
Closed the monitor? Click the UNO's USB port.

WIRING (the same in Proteus and on a real board)
  IN+ and IN- to the source (2 to 24 V), OUT+ and OUT- to the load. Turn the trimmer until the
  output has the voltage you
  want - on a real module that takes many turns before anything happens. To measure an output above
  5 V with an Arduino,
  divide it: 30 k over 10 k gives a quarter (good up to 20 V).
REAL HARDWARE:
 * The input current is larger than the output current by the voltage ratio and more: 0.4 A at 12 V
   from a 3.7 V cell
   costs about 1.5 A. Size the source and the wires for the INPUT current.
 * The chip's switch limits at about 4 A, but the little module gets hot long before: keep the input
   under 2 A or cool it.
 * The output cannot be switched off by the module: the input always passes through the inductor and
   the diode.
 * A new module's trimmer is often turned to the far end: turn it many turns (anti-clockwise on
   most) until the output
   starts to move, and set the voltage BEFORE you connect the load.
 * Never run a Li-ion cell flat through a boost converter: the module works down to 2 V, the cell
   must not go under
   2.5 to 3 V. Watch the cell's voltage, as the demo sketch does.

THE DEMO SKETCH ON THE SERIAL MONITOR (Boost_Demo V1.0, 9600 baud)
The sketch reports every 250 ms. Type a command:
  rate 1000  report every 1000 ms       help
EXPECTED MONITOR OUTPUT
  Boost converter monitor - The Engineering Projects
  Commands: rate 250 | help
  ...
  3.50 V in | 12.00 V out  0.40 A  4.80 W | ok
  3.48 V in | 12.00 V out  0.40 A  4.80 W | LOW BATTERY
  ...
  2.82 V in | 12.00 V out  0.40 A  4.80 W | LOW BATTERY
  3.03 V in | 2.66 V out  0.09 A  0.24 W | OUTPUT LOW

PROPERTIES (double-click the part > Edit Properties)
  Set voltage (VOUT)                   2 - 28 V: what the trimmer is turned to (12)
  Air temperature (TEMP)               -20 - 60 C (25)
Every run starts again from the properties.

LINKS.INI (OPTIONAL)
The Help page cards of the pop-up open web pages. To point them somewhere else without a new DLL,
put a text file named links.ini next to TEPMT3608.DLL with lines KEY=URL, for example:
  ARTICLE=https://www.theengineeringprojects.com/...
Keys: WEBSITE, FORUM, BUG_REPORT, FEATURE_REQUEST, ARTICLE, USER_GUIDE,
UPDATE_CHECK, DONATE. Only http:// and https:// links are used; lines starting
with # are comments.

TROUBLESHOOTING
* The output equals the input minus a little: the trimmer is set below the input (the pop-up says
  PASSING THE INPUT), the
  input is under 2 V (OFF), or the chip is too hot.
* The output sinks under load: the switch is in its current limit (CURRENT LIMIT) - the load asks
  for more than the
  input voltage allows. Raise the input voltage or lighten the load.
* The source's voltage collapses when the module starts: the source cannot give the input current. A
  boost converter
  asks for MORE current as its input voltage falls.
* OFF, "the input falls under 2 V when the chip starts": the source is empty or too weak. The chip
  stops under 2 V, the
  source recovers without the load, the chip tries again - and so on. Charge the cell or lighten the
  load.
* TOO HOT: more than about half a watt is lost in the chip. Lighten the load.
* The Arduino reads a wrong output voltage: the divider's factor in the sketch does not match the
  two resistors.
* The part is not simulated: TEPMT3608.DLL is missing from MODELS and from the project folder.
* The part is not simulated: TEPMT3608.DLL is missing from MODELS and from the project folder. No
  UNO / no monitor window: TEPARDUINO.DLL is missing, or click the UNO's USB port.

BUG REPORTS AND FEATURE REQUESTS
Please post them in our forum with a screenshot, the Serial Monitor text, the
simulation log and the pop-up's Copy diagnostics text:
  https://www.theengineeringprojects.com/forum/category/motor-driver-proteus-library

SUPPORT US
This library is free. If it saves you time, please support our work:
  https://www.theengineeringprojects.com/donate

WEBSITE
  https://www.theengineeringprojects.com/

LICENCES AND THIRD-PARTY NOTES
* The model (TEPMT3608.DLL), the symbols and artwork, the other parts of ours in the demo and the
  Arduino Library V4.0 (ArduinoV4TEP.LIB / TEPARDUINO.DLL, with its built-in TEP Serial Monitor
  Advance) are made by The Engineering Projects. The models use only standard Windows libraries; no
  Visual C++ redistributable is needed.
  The C++ source code is not included.
* Arduino UNO V4.0 (ArduinoV4TEP.LIB / TEPARDUINO.DLL, our Arduino Library V4.0 - its
  microcontroller is Proteus's own AVR model): The Engineering Projects,
  https://www.theengineeringprojects.com/2026/10/arduino-uno-library-for-proteus-v40.html
* The .hex file is built from the demo sketch and the Arduino AVR core 1.8.6, which includes
  LGPL-licensed code; its source code is available at
  https://github.com/arduino/ArduinoCore-avr/tree/1.8.6
* Proteus is a product of Labcenter Electronics and is not included. Arduino is a trademark of Arduino SA.
  This library is not made or endorsed by Arduino or Labcenter.

REBUILDING THE FIRMWARE (OPTIONAL)
The HEX file is supplied; Arduino IDE is not needed to run the demo. To edit the sketch, open
Arduino Code\Boost_Demo\Boost_Demo.ino, select Arduino Uno and use Sketch > Export Compiled Binary.
Replace the simulation's .hex with the exported HEX. The sketch needs 5,660 bytes of flash and 246
bytes of RAM.

MODEL SCOPE AND LIMITS
Modelled: the set voltage from the trimmer, the start at 2 V with a soft start, the power balance
with the losses in the
inductor (60 milliohm), the switch (80 milliohm times the duty), the diode (0.35 V) and in
switching, the 4 A switch
limit with the inductor's ripple, the pass-through path, the chip's heating and its thermal
switch-off. Our own
figures: the inductor's and the diode's resistance, the switching loss, 150 C/W and the 155 / 135 C
thresholds, the
20 milliohm output, the quarter of a second before a new try after an undervoltage stop. Not
modelled: the 1.2 MHz switching itself and the output ripple, pulse skipping at light load,
the chip's enable pin (tied to the input on the module).

VERSION
TEP MT3608 Boost Converter library V1.0 (Nov 2026). Device MT3608BOOSTTEP (TEPMT3608.LIB /
TEPMT3608.DLL). Demo sketch Boost_Demo V1.0 (no library needed). The demo also uses our 18650 Li-ion
Battery (TEP18650: LIION18650TEP), shipped in this package. Demo board: ARDUINO UNO V4.0 (TEP
Arduino Library V4.0) with its built-in serial monitor.
Advertisement

Development1 release

  1. V1.0MT3608 DC-DC Boost Converter Module Library for Proteus V1.0this page

    V1.0 is the only release in the Download Center so far. When a newer version is published, it appears above with its own download page.

Installation8 steps

From the download to a working project, in order. The steps follow what the package contains.

You will need

  • Proteus Design SuiteProteus 8 or newer (Labcenter), on Windows
  • Arduino IDE1.8 or 2.x, with the board of the tutorial chosen under Tools → Board
  • Any archive toolWindows, macOS and Linux extract ZIP files on their own

Steps

  1. 1

    Extract the archive

    Right-click 8bacb42e7c4440e1b82baa83265aea8d.zip and choose Extract All (or open it with 7-Zip or WinRAR) into a folder you can find again. Keep its folder structure (MT3608-Boost-Converter-TEP-v1.0) as it is.

  2. 2

    Copy the library files into Proteus

    Move ArduinoV4TEP.LIB, TEP18650.LIB and TEPMT3608.LIB and the files into the LIBRARY folder of your Proteus installation: C:\Program Files (x86)\Labcenter Electronics\Proteus 8 Professional\LIBRARY for Proteus 8, or the matching Proteus 7 folder. Older versions keep it under ProgramData\Labcenter Electronics. If Proteus is open, close it first.

  3. 3

    Add the simulation model

    Copy TEP18650.DLL, TEPARDUINO.DLL and TEPMT3608.DLL into the MODELS folder next to LIBRARY, so the component can run, not only be drawn.

  4. 4

    Restart Proteus and place the component

    Start Proteus, open a schematic, press P (Pick Devices) and search for the component by the name used in the tutorial. It appears with its pins ready to wire.

  5. 5

    Open the sketch in the Arduino IDE

    Open Boost_Demo.ino, select your board and port under Tools, then Verify. Sketch → Export Compiled Binary writes the HEX file a simulation needs.

  6. 6

    Load the HEX file

    In Proteus double-click the microcontroller, set Program File to Boost_Demo.hex and run the simulation. For real hardware, flash the same file with your programmer.

  7. 7

    Open the example simulation

    Open MT3608-Boost-Converter-18650-ArduinoUnoV4.pdsprj in Proteus to see the wiring exactly as in the tutorial. Check the controller's Program File path, then press Play.

  8. 8

    Follow the tutorial

    MT3608 DC-DC Boost Converter Module Library for Proteus Simulation explains every connection and setting in order; keep it open beside the files while you build.

How to add a library in Proteus 8

FAQs9 questionsContact TEP

How do I download MT3608 DC-DC Boost Converter Module Library for Proteus V1.0?

Wait for the 30-second guest countdown on this page, then press the download button; the file comes straight from our storage. Members who are logged in skip the wait. If the browser opens the file instead of saving it, use its Save as option. The download link is made for you when the countdown ends and works for 15 minutes; a saved or shared link stops working, so share this page instead.

What is inside the archive?

MT3608 DC-DC Boost Converter Module Library for Proteus V1.0 comes as a ZIP archive of 13 files (1.5 MB, 3.2 MB unpacked) holding Proteus library files, simulation model DLLs, a Proteus simulation, an Arduino sketch and compiled HEX firmware. Open the File Structure tab for the full list of 13 files.

What should I do if the download does not start?

Check the browser's download list first; an ad blocker or a company firewall can also hold it back, so try another browser or network. If the file arrives incomplete, download it again. For an installation problem, read the Install tab or tell us in the comments with your software version and the exact error message.

Is this file free?

Yes. Every file in the TEP Download Center is free for learning, personal and student projects. If you share it, link back to this page or the tutorial so others find the latest version.

How do I check that the file arrived complete?

Compare its SHA-256 with the one on this page, 2593dfdf2f50b70c7ce6fd7c6280cf449d91990720bd74cdc977c1c608ad4a05. In PowerShell run Get-FileHash "8bacb42e7c4440e1b82baa83265aea8d.zip"; on macOS or Linux run shasum -a 256 "8bacb42e7c4440e1b82baa83265aea8d.zip". The same value means the file is exactly the one in our storage; a different one means the download broke off, so download it again.

Do I need WinRAR to open the ZIP file?

No. Windows, macOS and Linux open ZIP archives on their own (Extract All, or double-click). WinRAR and 7-Zip work too. Extract the whole archive before using the files.

Where do I put the LIB and IDX files?

Both files go into the LIBRARY folder of your Proteus installation (Proteus 8: C:\Program Files (x86)\Labcenter Electronics\Proteus 8 Professional\LIBRARY; Proteus 7 has the same folder under its own name). Restart Proteus afterwards and search for the component with P.

Which Proteus version does the library need?

The tutorial names the Proteus version the library was made and tested with. Most TEP libraries work in Proteus 7 and Proteus 8; if the component does not appear after a restart, check that both the LIB and the IDX file were copied and that Proteus was fully closed while copying.

How do I get the HEX file into the simulation?

Compile the sketch in the Arduino IDE (Sketch → Export Compiled Binary gives you the HEX next to the sketch), then in Proteus double-click the board, set Program File to that HEX and run.

preparing · 8bacb42e7c4440e1b82baa83265aea8d.zip
Rating
Your download will be ready shortly
Preparing your download…

Members skip the wait. Log in or join TEP.

  • 0Total downloads
  • 4%Popularity
  • ProteusCategory
  • 0Comments
  • ssyedzainnasirUploaded by
  • 17 Nov 2026Uploaded at
Last 14 days0 downloads
SHA-256 2593dfdf2f50b70c7ce6fd7c6280cf449d91990720bd74cdc977c1c608ad4a05
DocumentationMT3608 DC-DC Boost Converter Module Library for Proteus Simulation
Need help with this file? Bug report Ask a question Download problemsGet updates
Advertisement

Comments

0

Join the conversation

Start the conversationAsk a question or share how you used this download.